Avycon AVR-HN5128E2N-FD-10T, AVR-HN5128E2N-FD-112T, AVR-HN5128E2N-FD-120T, AVR-HN5128E2N-FD-12T, AVR-HN5128E2N-FD-132T Quick Start Guide

...

Network Video Recorder

Quick Start Guide

Note: Please read this instruction carefully for correct use of the product and preserve it for reference purposes. All the examples and pictures used here are for reference only. There may be several technically incorrect places or printing errors in this manual. The updates will be added into the new version of this manual. The contents of this manual are subject to change without notice.This device should be operated only from the type of power source indicatedon the marking label. The voltage of the power must be veriﬁed before using the same.

1. Packing Check

Please check the device and the accessories after getting the device. If there are any damages, shortages or defects, please contact your dealer immediately.

2. HDD Installation

This series of the product supports 16 SATA hard drives. Please make sure that the device is powered off before the installation.

1.Get the brackets and screws of installing HDDs from the accessories and then ﬁx two brackets to the HDD.

2.Open the front panel of the device.

3. Use one hand to hold the handles of the two brckets respectively, and push the HDD into the HDD slot. Clamp the HDD to make sure the HDD to install successfully.

4. Choose the number of installing HDDs according to your need as above-mentioned methods.

Tips: Hold the handles of the two brackets to pull out the HDD

3. Rear Panel Installation

AUDI O OUTALAR M INALAR M OUT

AUDI O IN

e-SATA

LAN 1

LAN 2

VGA

USB

2 1

The interfaces of the rear panel are for reference only.

4. Startup & Shutdown

• Startup

1. Connect the monitor and the power.

2. The device will boot and the power indicator will display blue.

3. A wizard window will pop up.

• Shutdown

Go to “Main Menu” and then select “Shutdown” icon. This will bring up a shutdown window. The device will shut down by clicking “OK” button. Then disconnect the power.

4. Login

For our HN500 series NVRs, the default username is admin and the default password is 123456. You must conﬁgure the wizard if you

start the NVR for the ﬁrst time and you may change the password when you conﬁgure the wizard for the ﬁrst time. You can skip the settings of wizard next time. Click “Start” and select “Login”. This will take you to see a login box. Input default username and password you set and you can see the live image.

Use rname

Pas sword

adm in

Ent er Pass word

Dis play Pa sswor d Log I n Aut omati cally

Log inEdi t Secur ity Que stion Can cel

5. Network Configuration

After you ﬁnish adding IP cameras, you can see the live images through the monitor of the NVR. The following will mainly introduce how to add the IP cameras via LAN/WAN. This NVR has two network ports, you can select the network work pattern as required. Network fault toleratnce and multiple address setting are optional.

Network Fault Tolerance: Bound two network ports to one IP address. This pattern can increase the network bandwidth and form a network redundant array to share the load. When one port goes wrong, the other port will take over the entire load immediately and seamlessly. Multiple Address Setting: You shall set the IP address, subnet mask, gateway and DNS of each ethernet port respectively.The pictures are only for reference, please refer to User Manual for details.

• LAN

1. Set the network of the NVR. Go to Start → Settings → Network → TCP/IP. Input IP address, subnet mask, gateway, etc. If using DHCP, please enable DHCP in both the NVR and the router.

2. Go to Start → Settings → Network → Port. Input HTTP port (the default value is 80), server port (the default port is 6036).

3. User may modify the MTU(Maximum Transmission Unit) value according to the real network situation. Click “Apply” to save the settings.

TCP /IP Por t PPP oE DDN S E-mai l UPn P NAT Tel net

IP Addr ess Set tings

Work Pa ttern (Modi fying w ork pat tern ne ed to reb oot)

Netwo rk Faul t Toleran ce

Obtai n an IPv4 a ddres s autom atica lly Obtai n an IPv6 a ddres s autom atica lly

Addre ss Addre ss

Subne t Mask Mask Le ngth

Gatew ay Gatew ay

Prima ry Card

Ether net Por t 1 ( Onlin e )

MAC Add ress

MTU

4. Go to Start → Settings → Camera → Add Camera. The NVR will automatically refresh the cameras searched. The IPC which supports the Onvif protocol may be added manually. If the IPC searched is not in the same local network as the NVR, you should select the device and click to modify the IP address.

Qui ckly Ad d

No.

Sele cted: 1 /3

Rema in Band width : 108 / 120 M b

192 . 168 . 1 . 2

0 . 0 . 0 . 0 0

192 . 168 . 1 . 1

Ether net Por t 1

00：18：AE：3 5：64：1A

Man ually A dd

Addr ess

192. 168.1 .20

192. 168.1 .38

192. 168.2 .45

Mac Add ress

Addr ess

Subn et Mask

Gate way

Port

User name

Pass word

Add C amera

EditPort

255. 255.2 55.0

Edi t Camer a

CE :98 : 23 :75 :3 5 :22

192 .1 68 . 1 . 45

255 . 25 5 . 255 . 0

192 .1 68 . 1 . 1

admi n

Ether net Por t 2 ( Onlin e )

MAC Add ress

Subn et Mask

Defa ult Pas sword

OK Can cel

00：18：AE：3 5：64：1B

Prot ocol Mode l

XXX80

XXX

XXXXXX

Add

Versi on

3.4. 2

4.0. 0.1.b eta1

Canc el

5. Checkmark the device you want to add and then click “Add” button. The NVR will automatically refresh the cameras and return to “Edit Camera” interface. “Online” status means connecting the device successfully and you will see the live image. You may select the added device and click button to modify channel, IP address, ect.

Edi t Camer a

Rema in Band width : 85 / 120 Mb

No. Cam era Nam e

Edi t Camer a Group

Addr ess

192. 168.1 .20IP Came ra 1

192. 168.1 .38IP Came ra 2

192. 168.1 .45IP Camer a 3

Came ra Name

Addr ess

Port

Prot ocol

Mode l

User name

Pass word

Port

Stat us

Prot ocol

Onli ne

XXX

XXX80

Edi t Camer a

IP Cam era 3

192 . 168 . 1 . 58

XXX

admi n

Disp lay Pas sword

Mode l

XXX

XXXOffl ine

XXXOn line

Sear ch Came ra

Prev iew

Oper ation

OKTest Can cel

Sync t o IPC

Upgr ade

Versi on

4.1. 0.0

• WAN

1. Set the network of the NVR. Go to Start → Settings → Network → TCP/IPv4. Input static IP address or enable PPPoE and then input the user name and password received from your ISP.

2. Go to Start → Settings → Camera. Click “Add Camera” or behind the column of the search camera and select “Manually Add” to add the IP cameras. Input IP address, server port, username and password of the IP camera. The IP camera must be connected over WAN. And here the IP address of the IP camera must be a WAN IP address.

6. UPnP

You can use the UPnP function to enable the fast connection of the device to WAN via a router without port mapping.

1. Go to Start → Settings → Network → UPnP, and enable UPnP and then click “Apply” button to save.

2. Enable the UPnP function in the router.

3. Click “Refresh” button to refresh the UPnP status. If the UPnP status were still “Invalid UPnP” after refreshing it for several times, the port would be wrong. Please change the mapping type to “Manual” and then click to modify the port until the UPnP status turns to “valid UPnP”.

TCP /IP Por t P PPo E DDN S E- mai l UPn P N AT Tel net

UPn P

Enab le

AutoMap Typ e

Port

Port Ty pe

HTTP P ort

Serv er Port

RTSP Po rt

Exte rnal Po rt

6036

554

Exte rnal Add ress

UPnP S tatus Edit

80183. 17.25 4.19 Valid U PnP

Valid U PnP

60361 83.17 .254. 19

Inva lid UPn P

554

Refr esh Appl y

7. NAT

• NAT Setting

1. The NVR shall be powered on and connected to the network.

2. Go to Start → Settings → Network → TCP/IP. You can obtain the IP address, subnet mask and gateway automatically. You can also manually enter them according to the actual network situation. Please make sure the network segment is the same as that of the network which is used.

3. Set the preferred or alternative DNS Server. Click “Apply” to save the parameters.

4. Go to Start → Settings → Network → NAT tab. Enable NAT and select the NAT Server Address (The default NAT Server Address is nat.autonat.com). Click “Apply” to save the parameters.

TCP /IP Por t P PPo E DDN S E- mai l UPn P N AT Tel net

NAT

Vis it Addre ss www.a utona t.com

Ena ble

NAT Ser ver Addr ess

• NAT Access

After ﬁnishing the NAT settings, you can input www.autonat.com in the IE address bar and then press enter to go to the following interface. If you are the ﬁrst time to access the NAT, you shall download and install the ActiveX according to the popup tips. After installing ActiveX successfully, it will pop the login box.

nat .auto nat.c om

Appl y

Enter device ser ia l nu mb er

Enter Username

Enter Password

Logi n

Device Serial Number: Click on the menu bar at the bottom of the live interface to check the serial number or go to Start → Settings → Network →Network Status to check the serial number of the DVR).

Username: The username of the NVR. The default username is admin. Password: The password of the NVR. The password is set by yourself

when you conﬁgure the wizard for the ﬁrst time.

9. Manual Recording

Before recording, please install and format a HDD. In the live interface you can see the menu toolbar. Click button to start recording. Click it again to stop recording. You can also click to check the status of the recording.

10. Playback

• Instant Playback

Click “Instant Playback” in the right-click menu of the camera’s preview window to select or drag the playback progress bar to change the playback time to play back the record.

• General Playback

Click on the tool bar at the bottom of the live preview interface or click Start → Playback to go to the playback interface as shown below. You can also add the playback cameras manually. Click in the playback window to pop up the “Add Camera” window. Check the cameras in the window and then click “Add” to add playback camera. The record ﬁles of the added playback camera will be played in the playback interface.