Avue High Speed dome Camera, Outdoor 18x with WDR, Outdoor 26x with WDR, Outdoor 36x with WDR User Manual

High Speed dome
Camera Series

USER'S MANUAL

v 2.66

WARNING

CONTENTS

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE. DO NOT INSERTANY METALLIC OBJECTS THROUGH THE VENTILATION GRILLS OR
OTHER OPENINGS ON THE EQUIPMENT.

This symbol indicates that dangerous
voltage constituting a risk of electric
shock is present within this unit.

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK, DO NOT

REMOVE COVER ( OR BACK). NO

USER SERVICEABLE PARTS

INSIDE. REFER SERVICING TO

QUALIFIED SERVICE

PERSONNEL

This symbol indicates that there are
important operating and maintenance
instructions in the literature
accompanying this unit.

FCC COMPLIANCE STATEMENT

FCC INFORMATION: THIS EQUIPMENT HAS BEEN TESTED AND FOUND TO COMPLY WITH THE
LIMITS FOR A CLASS A DIGITAL DEVICE, PURSUANT TO PART 15 OF THE FCC RULES. THESE
LIMITS ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST HARMFUL
INTERFERENCE WHEN THE EQUIPMENT IS OPERATED IN A COMMERCIAL ENVIRONMENT. THIS
EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND IF NOT
INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTION MANUAL, MAY CAUSE
HARMFUL INTERFERENCETO RADIO COMMUNICATIONS. OPERATION OF THIS EQUIPMENT IN A
RESIDENTIAL AREA IS LIKELY TO CAUSE HARMFUL INTERFERENCE IN WHICH CASE THE USER
WILL BE REQUIRED TO CORRECT THE INTERFERENCEAT HIS OWN EXPENSE.

1. Precaution......................................................1

2. Features.........................................................2

3. Packing list.....................................................3

4. Installation...................................................... 4

5. Operation........................................................10

6. OSD................................................................11

7. Adress and Protocol Setting................................20

8. Specifications..................................................25

8. Motion Tracking..................................................26

CAUTION: CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE COULD VOID THE USERS‘S AUTHORITY TO OPERATE THE
EQUIPMENT.

CE COMPLIANCE STATEMENT

WARNING: THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT THIS
PRODUCT MAY CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER MAY BE
REQUIRED TO TAKEADEQUATE MEASURES.

CAUTION: BEFOREATTEMPTING TO CONNECT OR OPERATE THIS PRODUCT, PLEASE
READ THE LABEL ON THE BOTTOM AND USER'S MANUAL CAREFULLY

Technical specification are subjects to change without
prior notice. Manual may contain mistake or print error.
All trademarks mentioned belong to their respective owners.

1.PRECAUTION

2.FEATURES

Refer all work related to the installaion of this product to qualified service
personnel or system installers.

Do not attemp to disassemble the appliance

To prevent electric shock, do not remove screws or cover. There are no user­serviceable parts inside. Contact qualified service personnel for maintenance

Handle the appliance with Care

Do not strike or shake, as this may damage the appliance. It should be protected
against extreme pressure, vibration and humidity during transportation and storage.
Damages caused by improper transportation avoid the warranty.

Do not use strong or abrasive detergents when cleaning the appliance body and
transparent cover.

Use a dry cloth to clean the appliance when it is dirty. When the dirt is hard to remove,
use a mild detergent and wipe gently.

Do not operate the apliance beyond its specified temperature, humidity or power
source ratings.

Do not use the dome camera in an extreme environment where high temperature or
high humidity exists.
Use the within -10°C to +50°C(14°F to 122°F) and a humidity below
90%. The input power source is 24V AC, 50/60Hz and requires 1000mA.
Use the within -20°C to +60°C(-4°F to 140°F) and a humidity below
90%. The input power source is 24V AC, 50/60Hz and requires 2500mA.

Do not expose the indoor model of dome camera to water or moisture, not try to
operate it in wet areas.

Take immediate action when the indoor speed dome becomes wet. Turn off the power
and refer servicing to qulified service personnel. Moisture may damage the appliance
and cause eletric shock.

Do not point the camera lens directly to sunlight or any strong light source.

This will cause permanent damage to the camera and avoids the warranty.

Read this user's manual carefully before operating the appliance.

Make sure that local electric safty standard are followed when using or installing the
appliance

indoor models

outdoor models

The high speed dome camera series are designed for in- and outdoor video
surveillance application. The integrated, motorized pan-tilt mechanic allows user to point
the camera to any position( 360° horizontal and 180° vertical). Both series can be
equipped with digital zoom camera modules, which provide zooming functon from 18 to
36 times (optical) and advanced image features.

Key features:

- 360° Pan and 180° Tilt range (90° with auto-image-flip)

- Support most well-known camera modules

- 128 preset points memory (80 can be used for auto tour function)

- 4 patt ern tou rs

- 1 Scan t our

- Basic setup directly from Keyboard.

- Advanced setup through OSD (On Screen Display) menu.

- up to 24 privacy masking zones ( despends on camera module)

- 7 alarm input & 2 output ( 4 input & 1 output pre-wired)

- Multi-Protocol through Rs485 or coaxial cable.

- Dirction Indicator on screen

- Aluminum Alloy structure with high intensity and heat-sinking

- High-precision step-motor for flicker-less image during movement.

Camera Features:

- HighResolution with 560TVL and Wide-Dynamic*

- Interlace and Progressive Scan*

- Auto-Focus

- Auto-Iris

- Auto- Brightness control

- Auto-Balance

- IR cutter control, Day-Night mode switching.

- Auto Slow-Shutter

- Electric Image Stabilization

- Stablezoom*

Temperature monitoring and protection

- Alarm notification will be displayed once the inner temperature exceeds the limit

- In low temperature area, the dome camera will only start after the operation
temperature is reached.

- Cooling fan activity is managed by the CPU ( extends the duration)

Do not install the camera in other orientation as designed.

And do not bend or squeez the sturctiure, as this may damage the mechanic sturcture
of the appliance and avoids the warranty.

Do not touch the Cover with bare hands or any object.

These will scratch the serface and affect the image qulaity.

12

Some products may not be available in your country, please contact our distributor for more details Some products may not be available in your country, please contact our distributor for more details

Other features:

- Proportional pan for Focus / Speed on different zoom factor.

- Auto-resuming user-defined action, such as tour, pattern or scan after selectable idle
time.

- Power-upAction activates tour or pattern by default.

depends on camera module type.

*

3.PACKING LIST

4.INSTALLATION

Indoor
Series

Outdoor
Series

Outdoor
Series

Core Unit
1 Piece

Core Unit
1 Piece

Core Unit
1 Piece

Indoor Roof-Mount
base platte
1 piece

Out-Door housing
with sun.shield and

cover

1 piece

Out-Door housing
with sun.shield and

cover

1 piece

High Speed dome
Camera Series

USER'S MANUAL

Instruction and
operation manual
1 piece

Spare dome cover
1 piece

Spare dome cover
1 piece

High Speed dome
Camera Series

USER'S MANUAL

Instruction and
operation manual
1 piece

High Speed dome
Camera Series

USER'S MANUAL

Instruction and
operation manual
1 piece

Safety Instructions before starting

- Do not install and operate this appliance in a flammable and explosive environment.

- Make sure that the installation is done according to the local electricity safety regulation
of your country.
.

- Before installation and mentainence, make sure that the appliance is disconnected
from the power source.

- Do not use any power source other than 24V AC, in order to prevent damages to this
device. For details, please refer to the section "Precaution" in previous chapter for
more details.

- Handle the device during the installation carfully. Falls or extreme vibration may cause
irrepairable damages and avoid the warranty.

- Do not install or operate the appliance near any high-voltage devices or high-voltage
cable. The safety distance should remain at least 50 m.

- To archive best image quality, its recommanded to use underground cable shielded with
steel tube. Do not install the cable without any protection.

- In a thunderstorm area or region with high inductive voltage, such as high voltage
transformer stations, it is necessary to use additional lighning-proof equipments or
lightning rob for protection.

- For outdoor installation, lightning-proof and grounding of the device should be
considered. Please refer to the industrial saftey regulation and request of your country
.

- Grounding of the appliance should consider anti-interference and fulfill the saftey
requirements. Do not connect the ground with short-circuited or other high-voltage
electric network.

WARNING:

be handled with care. Do not touch or rub the surface in any way
with the protection foil.Inproper cleaning method will cause
permanent scratches on the cover and cause unclear image or
focusing error of the camera. For Cleaning the cover, please
replace the original first with the spare cover, and wash it by
diving into warm water with non-corrosive cleaning solution.

The transparent cover part is sensitive and should

Unpacking

The speed dome is packed with protection. please take
out the core unit carefully. In case of transportation
please use the original packing box.

3

Some models may not be available in your country, please contact VIDO distributor for more details

- The resistance of down conductor should not exceed 4 Ohm, and its thickness should
be at least 25mm²

- This appliance has the lightning-proof function which can prevent damages caused by
high-voltage pulse, such as lightning strike below 1500.

- This appliance meets the Ip66 standard for water and dust proof. Do not install the in­door model for out-door application which is not designed with water protection. Make
sure that the installation is protected from long-time water-drop or spatter, which may
damage the appliance.

- Make sure that the enviroment of installation meets the requirement of the appliance,
such as holding the weight, enough spaces for bracket and power supply.

Some products may not be available in your country, please contact our distributor for more details

4

4.INSTALLATION

4.INSTALLATION

Connector description

The wiring cable of the PTZ camera provides connectors for power supply, video and
I/O interface

RED: AC 24V
BLACK: AC 24V

Power

To power supply

Connector

Green:RS485+

RS485
Connector
RJ-11

Yellow:RS485-

To Keyboard or DVR decives for
telemetric control

Inner Conn: Signal +
Outer Conn: Ground

Video output

Video Output to monitor or DVR

BNC

Using optional accessories

The speed dome cameras can be connected to various optional accessories through
the standard connector types, which simplifiy the cable handling and avoids possible
mistakes. All accessories are tested for max. compatibility and best performance.

Outdoor power adaptor box
AC 230V to AC 24V

AC 24 Power

supply

RS 485

Alarm I/O

AC 230V

Power input

Indoor power adaptor
AC 230V to AC 24V

AC 24 Power supply

AC 230V
Power input

3-Axis keyboard

controller

RS 485

21”High Res.
security Monitor.

Professional Real-time
16 Channel DVR

Telemetric control
camera setup

RED: Alarm in 1
PINK: Alarm in 2
YELLOW:
GREEN:
BLACK: COM
WHITE: Alarm output - N.O

Alarm I/O 1

BLUE: Alarm output - N.C

AQUA
BROWN: Alarm output - N.O2
GRAY: Alarm in 7
PURPLE: Alarm in 6
ORANGE: Alarm in 5

I/O interface to additional alarm sensor

Alarm I/O 2

56

Some products may not be available in your country, please contact our distributor for more details Some products may not be available in your country, please contact our distributor for more details

or control devices

Alarm in 3

Alarm in 4

Alarm output - N.C2

:

RS 485 cable

The telemetric control of the appliance uses Rs485 serial communication with half­duplex transmission technology.
Depends on the cable typeand baud rate, the transmission distance could vary. The
following table shows max. distances based on cable with 0,56mm (24AWG) twisted
pair:

Baud Rate

2400 bps
4800 bps

9600 bps

19200 bps

Max. Distance

1700m

1100 m

700m

4oom

Video signal

Due the environmental interferences, such as
eletromagnetic and induction fields, or number of
connected appliance on the RS-485 bus, the
transmission range may be less, e.g with cable thinner
than than 24AWG.

4.INSTALLATION

4.INSTALLATION

RS-485Termination

Devices using Rs485 control are usually connected in daisy-chain. which reqiuers
termination with 120 resistor on both ends. Following picture illustrates the

Ω

connection methods. please note that a daisy-chain connection type shall not
exceed 7 meters.

120

Resistor

RS 485+

Ω

Device 2 Device 3Device 1

RS 485-

120

Resistor

Ω

The PTZ cameras provide integrated termination switch. It should be turned on
when the dome is installed as the last device. If the controller keyboard is used,
you need also to turn on the termination on it. please refer to the keyboard’s
manual for details.

RS 485+

RS 485-

Termination on

Termination
on

Termination
off

Termination
off

How to turn on termination on the high speed dome camera

The termination switch is located on the rear side of the connection board. For
switching on, you need to open the

Star-Connection

The star-form connection is mostly used. it enables the connection of different dome
cameras in longer distance. It is recommended to use RS-485 distributor to ensure the

telemetric data transmission:

The advantage of star-connection is
that every channel can work

RS-485 cable
up to 1000m
per channel

RS-485
Distributor

Termination on

Termination
activated on
every end.

independently and take a cable
length up to 1000 meters( depends
on cable quality). In case more
dome camera are installed, the star­connection can be extended with
additional RS-485 distributors.

Video Cable

coaxial cable with 75 impedance with copper conductor at center conductor, and

Ω
shielded with 95% copper. The following table shows different cable type and its
maximum length:

Cable standard

RG 59 /U

RG 6 /U

RG 11 /U

Max. Distance (m /ft )

229m / 750 ft

305m/ 1000 ft

457m / 1500 ft

The values are for reference only.
Depends on the cable quality and
environmental condition, the
transmission distance might be less.

If the cable length is more than 400 m, it is recommended to use optional
accessories, such as video amlifier or twisted-pair video converter , for boost
the video signal.

How to open the connector board

The connector board can be easily

rear side

123

Termination
Jumper

Jumper

Term. On

7

Some products may not be available in your country, please contact our distributor for more details

Term. Off ( default)

123

ON

ON OFF
ON

OFF

opened by holding the metal clip and
pull.

ON

Metal
Clip holder

Pres s the met al
clip in and pull
the board on this
direction.

Up to 750m, coaxial cable

VideoAmplifier
(optional)

Extend connection distance with
video amplifier

Up to 1200m, twisted pair or cat.5 cable

transmitter

(optional)

Extend connection distance with Twisted-Pair
video converter

Some products may not be available in your country, please contact our distributor for more details

Real time DVR Center

TP receiver
(optional)

Real time DVR Center

(optional)

(optional)

High Res Monitor
(optional)

High Res Monitor
(optional)

8

4.INSTALLATION

5.OPERATING THE SPEED DOME

Installing the core unit to base board.

The PTZ camera core unit and base board are packed seperatly, in order to be
protected through the transportation. After unpaking and during the installation, the
core unit should be installed as following:

Installing the core unit by
pushing into the
housing.please note the
position of connector. For
releasing, please press the
lever-lock to core and pull off
the unit.

Once the base board is connected to power,
the power LED will light.

Connector
Interface

Power
LED

Metal
Clip

WARNING:
Do not pull or hold the connector interface with force. It
is design only to connect the core unit and the base
board. Any presure on connector will cause damage and
avoids the warranty.

Heater connector
on outdoor
housing

Screws

Rubber ring

Outdoor
housing cover

cable

Lever­Lock

Safety spring

Heater connector

Optional bracket accessories

The PTZ cameras can be equipped with various bracket accessories for indoor
and outdoor installation. please contact your distributor for further details.

Initial Screen

FIRMWARE V2.61
Protocol: PELCO
Dome Address: 001
Comm 9600,N,8,1

- V2.61:

- Protocol:

Current firmware version

control protocol which currently used

- Dome address:

Address ID of speed dome. please refer to the section "Protocol

After powering up, the camera will enter the
self-test mode and display the status screen(
as in the picture left).It contains information
about the model and current settings.

setup " for details.

- Comm 9600,N,8,1:

Baud rate. please refer to section "Baud-Rate setup" for details

9600:
N, 8, 1:

No parity bit, 8 bit length, 1 stop bit. this setting can not be changed

current setting of the serial communication interface.

The intial screen will stay remain on until any user action is being taken. If the power­up action is set, the initial info wil vanish immediatly.

Operation Screen

Temperature

The operation screen can display additional
information.

32.0CAM TITLE

Temperature: current temperature inside the
speed dome( °C)
Cam title: User definable camera title
Zone: Current zone name

ZONE-1
285 78 18X

Pan deg.: Pan angle, 0-359°
Tilt deg.: Tilt angle, 0-90°
Zoom Factor: Zoom factor

Zoom factor

Ceilling
mount

Wall mount and

Power box

Corner
Mount

Indoor Wall
mount

Pole
Mount

Outdoor
Power Box

Display of the information can be activate or
deactivate through the OSD menu. please refer to
the system setting for detais.

PTZ operation

Tilt degree
Pan degree

Zone description

For the surveillance operation, the dome can be controlled from a keyboard device,
Multiplexer or DVR through RS-485 Interface. Make sure that the cable is connected
and the settings (baud rate,Address ID and protocol) of both keyboard and the dome
are configured correctly. For more description about the PTZ operation, please refer

Indoor
embedded
mount

910

Some products may not be available in your country, please contact our distributor for more details Some products may not be available in your country, please contact our distributor for more details

Indoor ceilling
mount

Extended wall
mount

Swan-Neck
Mounting
bracket

Wall
mount

to the user’s manual of the keyboard.

OSD

OSD Menu

The PTZ cameras are equipped with new OSD-Menu function. All operation functions and
camera related settings can be changed or modified here. In order to use the OSD function,
a telemetric controller device, such as Keyboard, DVR or other devices with similiar function
is necessarily required. please make sure that the device used is physically connected to the
dome properly, and all connection parameters are set correctly.

OSD - MAP

ALARMS SETTING

ALARM NUMBER 001

ALARN ACTION NONE

ACTIVATEAUX NONE

ALARM PRIORITY

BACK

EXIT

ARM SETTING

DAY SUN

UNARM TIME N/A

ARM STATE OFF

ARM TIME N/A

BACK

EXIT

How to start the OSD menu

To start the OSD Menu, you need to press following key on the keyboard:

2-Axis

With or

keyboard

3-Axis

With or

keyboard

call

Shot

9 5

9 5

Enter

Enter

2 X

2 X

call

Shot

Enter

9

Enter

9

In case a DVR is used for the OSD, select “goto preset 95” or 2 X “goto preset 9”. Please
refer to the DVR’s operation manual for more details.

Note that in some certain situations, it is not possible to enter the OSD menu:

1. the dome is running tour

2. performing PTZ operation

3. dome is receiving command other than OSD-request from the keyboard.

please stop the operation and try again.

Main menu and navigation

After entering the OSD Menu, the screen will show menu
items . Use the controller’ joystick to navigate through

Main Menu

the menu’s main and sub items by moving in the
direction. The angle mark on the beginning of every

SYSTEM SETTING

items indicates the selection.
CAMERA SETTING
FUNCTION SETTING
WINDOW BLANKING
ALARM
EXIT

UP, DOWN: - Moving between current menu items

- Changing the value in subitems

RIGHT: - Enter the selected menu item

- Confirm the value change and return to

item selection

LEFT: Exit from sub menu

For more inforamtion, please refer to the illustration on

the next page for the OSD menu structure.

Symbols and indicator

Cursor.

Sub item is selected. use up or down to change value

This item has subitem(s)

MAIN MENU

→

→

SYSTEM SETTING

CAMERA SETTING

→

→

FUNCTION SETTING

WINDOW BLANKING

→

ALARMS

EXIT

→

→

ALARMS

RESUME OFF

SEQUENCE 60

RESET DELEY 030

ALARM CONTACT N/O

ALARM SETTING

ARM SETTING

WINDOW BLANKING

WINDOW NUMBER 01

EDIT WINDOW

ENABLE WINDOW ON

CLEAR WINDOW

BACK

EXIT

FUNCTION SETTING

CAMERA SETTING

ZOOM SPEED HIGH

DIGITAL ZOOM ON

BLC MODE OFF

SLOW SHUTTER ON

LINE SYNC N/A

WDR MODE AUTO

ADVANCE SETTING 1 →

→

→

→

→

→

→

SYSTEM SETTING

EDIT DOME LABEL

INITIAL INFO

DISPLAY SETUP

MOTION

CLEAR

PASSWORDSETUP

BACK

EXIT

→

→

→

PRESETS

SCAN

PATTERNS

→

ADVANCE SETTING 2

BACK

EXIT

CLOCK SETTING

BACK

EXIT

→

TOUR

→

→

ZONES

TIME RUNNING

ADVANCE SETTING1

AUTO-TRACKING

BACK

PS SCAN O N

ADVANCE SETTING1

IR CUTTER FILTER AUTO

EDIT DOME LABEL

EXIT

LABEL:SPEED DOME

-- -

-- -

-- -

-- -

-- -

EDITTOUR

LABEL: PRESET-01

PRESET NUMBER 001

SET PRESET

MIRRO R OFF

FLIP OFF

INITIAL INFO

BACK

EXIT

SHOW PRESET

NEXT→

→

CLEAR PRESET

EDIT PRESET LABEL

2.66

VIDO B02

SPEED DOME V

PROTOCOL :

DOME ADDRESS: 001

BACK

EXIT

ADVANCE SETTING2

96

COMM: 00 . N.8.1

EDIT SCAN LABEL

LABEL: AUTO SCAN

SCAN

SCAN NU MBER 01

SCAN SPEED 63

SHUTTER N/A

IRI S N/A

BRI GHT N/A

R GAIN N/A

B

AE MODE AUTO

W M ODE AUTO

BACK

EXIT

BACK

SET LEFT LIMIT

B GAI N N/A

DISPLAY SETUP

EDIT PATTERN LABEL

EXIT

→

PATTERNS

PATTERN N UMBER 1

SET RIGHT LIMIT

CLEAR SCAN

RUN SCAN

EDIT SCAN LABEL

BACK

EXIT

HI-RESOLUION ON

BACK

EXIT

FF

FF

DOME LABEL OFF

PRESET LABEL OFF

ZOOM LABEL O

ZONE LABEL OFF

DIRECTION LABEL O

TEMPERATURE LABEL OFF

TIME LABEL OFF

DATE LABEL OFF

BACK

EXIT

EDIT PRESET LABEL

PRESETS

STABLE Z OOM OFF

DNR 00

BACK

EXIT

IR CUT ON T IME N/A

IR CUT OF F TIME N/ A

THRES HOLD 10dB

MAX GAI N 28dB

EXPOSURE COMP OFF

BACK

EXIT

LABEL: PATTERN-1

BACK

PROGRAM PATTERN

RUN PATTERN

EXIT

CLEAR PATTERN

→

EDIT PATTERN LABEL

BACK

EXIT

ADVANCE SETTING

MOTION

TM TM TM

P0-S- P0-S- P0-S-

TOUR

ESET FREEZE FF

PR N O

EIS ENABLED ON

AUTO FLIP ON

PROPORTION PAN ON

PARK TIME 005

AUTO FOCUS OFF

00-0-00 00 0 00 00 0- 00

NUMBER 1

TOUR

NONE

PARK ACTION

DEFOGGER 015C

00-0-00 00 0 00 00 0- 00

→

EDITTOUR

NONE

POWER UP ACTION

00-0-00 00 0 00 00 0- 00

RUN TOUR

HEAD UP OFF

FAN ENABLED 040

EDIT ZONE LABEL

LABEL: ZONE-1

BACK

00-0-00 00 0 00 00 0- 00

00-0-00 00 0 00 00 0- 00

CLEARTOUR

BACK

BACK

EXIT

TEMP C/F CENT

ADVANVE SETTING →

EXIT

BACK

EXIT

→

ZONES

ZONES N UMBER 1

EXIT

BACK

EXIT

SETLEFT LIMIT

CLEAR

SETRIGHT LIMIT

CLEAR ZONE

EDITZONE LABEL

CLEAR ALL ZONES

CLEAR ALL PRESETS

BACK

EXIT

CLEAR ALL PATTERNS

CLEAR ALL TOURS

CLEAR ALL WINDOWS

FACTORY DEFAULTS

RESTART

BACK

TIME RUNNING

DAY SUN

EXIT

START TIM E 00:00

RUNNING NONE

TIME CHANNEL 1

BACK

EXIT

PASSWORD SETUP

OLD PASS WORD : ** ****

NEW PASS WORD : ******

CONF PASSWORD : ******

ENABL E PASSWO RD OFF

AUTO-TRACKING

DAY SUN

BACK

EXIT

STATE ON

START TIM E N/A

END TIM E N/A

CLOCK SETTING

→

→

SENSITIVE LOW

TRACKING-ZOOM OFF

SETLEFT LIMIT

SETRIGHT LIMIT

BACK

EXIT

TIME 00:00:00

DATE 01/01/01

DAY MON

BACK

EXIT

Some products may not be available in your country, please contact our distributor for more details Some products may not be available in your country, please contact our distributor for more details

6.OSD - System Setting 6.OSD - Motion, Clear

SYSTEM SETTING

EDIT DOME LABEL
INITIAL INFO
DISPLAY SETUP
MOTION
CLEAR
PASSWORD SETUP
CLOCK SETTING
BACK
EXIT

EDIT DOME LABEL

LABEL

：

ENTRANCE

BACK

EXIT

INITIAL INFO

SPEED DOME V1.00
PROTOCOL：FACTORY
DOME ADDRESS：001
COMM：4800,N,8,1
BACK
EXIT

DISPLAY SETUP

DOME LABEL OFF

PRESET LABEL OFF

ZOOM LABEL ON

ZONE LABEL OFF

DIRECTION LABEL ON

TEMPERATURE

BACK

EXIT

LABEL OFF

System Setting

In system setting menu, you can modify operation and

display setting, such as dome label, temperature and

display of various value on the operational screen.

Dome Label:

1. use UP or DOWN to change the charactor.

2. u se RIG HT to m ove t o next c har.

3. u se RIG HT to m ove t o last c har a nd save.

4. u se Lef t to fi rst ch ar an d canc el.

Initial information:

Shows the information about current setting.

Display setup

Actuvate the display for the on-screen info in operaton

mode.

Dome label:

Preset label:

Zoom label:

Zone label:

Direction label:

Temperature label:

shows the cur. temp in the speed dome

the name of dome

shows the labe of every preset

shows zoom factor on screen

shows the zone name

shows the coordinates

MOTION

AUTO FLIP ON
PROPORTION PAN ON
PARK TIME 005
PARK ACTION SCAN
POWER UP ACTION AUTO
FAN ENABLED 040
TEMP C/ F CE NT
ADVANCE SETTING
BACK
EXIT

ADVANCE SETTING

EIS ENABLED N/A
PRESET FREEZEN OFF
AUTO FO CU S OF F
DEFOGGER 015C
HEAD UP OFF
BACK
EXIT

CLEAR

CLEAR ALL ZONES
CLEAR ALL PRESETS
CLEAR ALL PATTERNS
CLEAR ALL TOURS
CLEAR ALL WINDOWS
FACTORY DEFAULTS
RESTART
BACK
EXIT

Motion control

AUTO FLIP

180°

PROPORTIONAL PAN:

the dome will adjust the pan and tilt speed
automatically for comfortable viewing.

PARK TIME:

custom defined action( park action).The range is
from 1 to 240 minutes. This function can be
deactivated by setting the minute to 0.

PARKACTION:

the idle time (park time). Selectable between Preset,
Scan, Pattern (Nr), Tour or None.

POWER UPACTION:

be started after power up and self test. Selectable
between Auto,Preset 1, Scan, Pattern (Nr), Tour or
None. By selecting Auto, the dome will resume the
last action before power off.

FAN ENABLED:

temperature.

TEMP C/F:

Fahrenheit.

: Auto. Image flip in tilt range from 90° to

depends on the zoom factor,

defines the idle time prior to start a

the action which will be started after

defines the action which will

Activate Fan when the dome reach the

Switch the temperature unit between Celius and

Advance Setting

EIS ENABLED: E I S

function is variable on certain camera modul.

PRESET FREEZEN:
AUTO FOCUS:
DEFOGGER:
HEAD UP:

combine with Camera Flip function.

Clear

You can clear setting’s memory or reset the camear to
factory default. The follwing functions are supported:

- Clear Zones

- Cl ear al l pre sets

- Clear all patterns

- Clear all tours

- Cl ear al l win dows

- Factory defaults

Warning: The c lear a cti on can n ot be u ndon e.
once a item is cleared it is impossible to
re trie ve th e del eted s ett i ng. P leas e mak e sur e
that the requested clear action is desired.

Enable „ lectric mage tabilization“. This

Freeze the image immediately.

Switch ON/OFF the Auto Focus

Activate Heater/Fan on the cold temperatur.

Switch ON/OFF the proportional PT moving. Can

13 14

Some products may not be available in your country, please contact our distributor for more details Some products may not be available in your country, please contact our distributor for more details

OSD - Camera Setting OSD - Preset, Scan

PASSWORD SETUP

O

LD PASSWORD : ******
NEW PASSWORD : ******
CONF PASSWORD : ******
ENABLE PASSWORD OFF
BACK
EXIT

CLOCK SETTING

TIME 00:00:00
DATE 01/01/01
DAY MON
BACK
EXIT

Password setup

You can change password to access the OSD menu.
Default Password is 000000.

Clock setting

Some function like Auto-Tracking require the timer for
activation.
Time: HH:MM:SS
DATE: YY/MM/DD
DAY: MON-SUN

CAMERA SETTING

CAMERA SETTING

ZOOM SPEED HIGH
DIGITAL ZOOM ON
BLC MODE OFF
SLOW SHUTTER ON
LINE SYNC N/A
WDR MODE N/A
ADVANCE SETTING 1
ADVANCE SETTING 2
BACK
EXIT

In camera setting menu, you can setup camera module
related settings. please note that depends on module’s
capability, some function may not available. please contact
your local sales representative for detailed information.

ZOOM SPEED:

function.

DIGITAL ZOOM:

function of the camera module.

BLC MODE:

improves the image when an object has strong back light.

SLOW SHUTTER:

of the camera, which provides a higher light sensibility
in low-environment.

WDR:

Activates the Wide Dynamic Range function, which
improves the image contrast when an object has very
strong light on background. Only available with camera
modules with WDR.

defines the speed when performing zoom

Activate or deactivate the digital zoom

Select the Back Light Compensation mode,

Activates the Slow Shutter function

ADVANCE SETTING1

IR CUT FILTER:

ADVANCE SETTING 1

IR CUTTER FILTER AUTO

IR CUT ON T IM E N/ A
IR CUT OF F TI ME N /A

THRESHOLD 10dB
MAX GAIN 28dB
EXPOSURE COMP OFF
MIRROR OFF
FLIP OFF
NEXT

15

Some products may not be available in your country, please contact our distributor for more details Some products may not be available in your country, please contact our distributor for more details

Filter (IRC), also known as “DAY/NIGHT” mode. with the
removal of IRC, the camera turns into Black/White mode and
has higher sensibility to low-light or IR-Light in the night.
Selectable between On, Off, Auto or Time. Only available
on camera module with IRC function.

MAX GA IN :
EXPOSURE COMP:

of a short exposure.Configure the shutter speed of a long
exposure by setting the ratio with regards to a short
exposure with the exposure ratio parameter. Blocked-up
shadow correction is not performed in this mode.

Mirror:
Flip:

This function reverses the camera horizontally.

This function turns the camera upside down.

Enables the removal of Infrared Cutter

improve the image quality in the Night modus

This mode fixes the shutter speed

ADVANCE SETTING 1

PS SCAN ON
STAB LE Z OO M ON
DNR 00
BACK
EXIT

ADVANCE SETTING 2

AE MODE AUTO

SHUTTER N/A
IRIS N/A
BRIGHT N/A

WB MODE AUTO

R GAIN N/A

B GAIN N /A
HI-RESOLUTION OFF
BACK
EXIT

FUNCTION SETTING

PRESETS
SCAN
PATTERNS
TOUR
ZONES
TIME RUNNING
AUTO-TRACKING
BACK
EXIT

PRESETS

PRESET NUMBER 001
SET PRESET
SHOW PRESET
CLEAR PRESET
AUTO-TRACKING ON
EDIT PRESET LABEL
BACK
EXIT

ADVANCE SETTING 1

These function are o
camera modules

PS SCAN:

on the WDR mode.

STABLE ZOOM:

using the Image Stabilizer function in accordance with
the zoom ratio, and smoothly zooming up to
approximately ×40 using a combination of the optical
zoom and digital zoom.

DNR: D N R

Activate Progressive Scan, can be combine

Set the 2D/3D igital oise eduction.

nly available with the E-Serie

This function is performing correction

ADVANCE SETTING 2

Under the advanced setting, you can make
improvements to image quality due to different
environmental conditions.

AE MODE:

Auto Exposure mode. Depends on the light
condition in the surveillance area, you can set the AE in
different modes and adjust the parameters, such as
shutter speed, iris factor and brightness for the best
image quality.

WB MODE:

White balance mode, a image improvement
based on DSP processing. you can also adjust the Red­Gain or Blue-Gain to change the color tone.

ALC, PLC:

Average and Peak Level Control,
additional setting to WB function. only avialble with
dedicated camera modules.

FUNCTION SETTING

In function setting menu, you can define and activate
different PTZ funcitons, such as preset points, auto
scan, tours and Pattern. Presets and tour functions
can also be set or activated directly from keyboard
device without OSD. Please refer to the keyboard’s
manual for operation details.

PRESETS:

PRESET NUMBER:

G65-70 Series supports up to

128 presets. The number can be selected from 0 to

128.

SET PRESET:

Defining the preset points directly in
OSD by entering this menu item and move the PTZ.
press IRIS-OPEN key on the keyboard to save. If the
preset is pointed within digital zoom, it will
automatically go back to max. optical zoom range in
order to provide the best image.

SHOW PRESET:

Moves to current preset point

6.OSD - Patterns, Tours 6.OSD - Zones and Privacy Mask

CLEAR PRESET:

Clear the current preset

EDIT PRESET LABEL

AUTO-TRACKING:

LABEL

：ROOM 1
BACK
EXIT

SCAN

SCAN NUMBER 01
SCAN SPEED 63
SET LEFT LIMIT
SET RIGHT LIMIT
CLEAR SCAN
RUN SCAN
EDIT SCAN LABEL
BACK
EXIT

PATTERNS

PATTE RN NUMB ER 1
PROGRAM PATTERN
RUN PATTERN
CLEAR PATTERN
EDIT PATTERN LABEL
BACK
EXIT

17

Some products may not be available in your country, please contact our distributor for more details

is called.

EDIT PRESET LABEL:

can define a name which will be shon on the
operation screen once the preset is called. please
choose the preset number at first. The avaialbe
characters are: 0-9, A-Z, <,>,. and space.

SCAN

Th e SCAN f unc tion m ove s the P TZ bet wee n 2­predefined points in constant speed.The
following parameters can be set:

SCAN NUMBER:

scan.

SCAN SPEED:

points.

SET LEFT LIMIT:
SET RIGHT LIMIT:
CLEAR SCAN:
RUN SCAN:
EDIT SCAN LABEL:

Pattern

Patte rn re cord s the u ser’s ope rat ion s teps o n
pe rfor min g PTZ co ntr ol and s tor e s as a track . The
Sp eed Do me ca n reco rd up t o 4 tra cks wi th ma x.
180 sec. each.

PATTERN NUMBER:

from 1 t o 4

PROGRAM PATTERN:

when selected. you can perfome PTZ movement for
recording and shall not exceed 180 sec. Press IRIS­OPEN to save the track.

RUN PATTERN:

CLEAR PATTERN:

EDIT PATTERN L ABEL :

pattern.

Start Auto Tracking, if the preset

For th e curre nt preset, y ou

The Speed Dome

cruising speed between the

defines the left point.

de fine s the r ight p oin t

Delete the scan setting

starting the scan function

se t the na me fo r the sc an

Selects the pattern number,

Starts recording the pattern

Starts the current pattern

Delete curretn pattern.

Sets t he name f or current

supports up to 4

EDIT TOUR

TOUR DWELL 001
00-00-00-00-00-00-00-00
00-00-00-00-00-00-00-00
00-00-00-00-00-00-00-00
00-00-00-00-00-00-00-00
RUN TOUR
BACK
EXIT

ZONES

ZONE S NUMBE R 1
SET LEFT LIMIT
SET RIGHT LIMIT
CLEAR ZONE
EDIT ZONE LABEL
BACK
EXIT

TIME RUNNING

DAY SUN

TIME CHANNEL 1
START TIME 0 0:00
END TIME 00:00

RUNNING NONE
BACK
EXIT

AUTO TRACKING

DAY SUN

STATE ON

START TIME 0 0:00

END TIME 00:00
SENSITIVE LOW
TRACKING-ZOOM OFF
SET LEFT LIMIT
SET RIGHT LIMT
BACK
EXIT

Some products may not be available in your country, please contact our distributor for more details

Tour

Tour is an auto-run through selected preset
po ints w ith d efin abl e paus e tim e . A tou r can
store up to 32 presets points.

TOUR DWELL:

preset points. selectable between 000-255(s).

TOUR PRESETS:

ke ybo ard de vic e to ent er th e p res et po i nt
selection. Move the joystick with up and down to
se lect t he pr eset p oin ts by nu mbe r and sa ve th e
setting with IRIS-OPEN key. with IRIS-CLOSE
ke y you c an mo ve to t he pre vio u s sel ecti on. I f a
se lect p oin t has th e va l ue 0, a ll the f oll owin g
presets points will be ignored.

RU N TOU R:

menu.

pa use ti me fo r eve ry sto p on th e

pr ess IR IS- OPEN Key o n the

St arts t he to ur and e xit t he OSD

ZONE

You c an def ine t he zon es in t he who le PT r ang e up

up t o 8 zon es

to with individual label. When the
display setting “Zone Label” is activated, the
la bel wi ll be d ispl aye d on th e operati on sc reen .
Th e defi nit ion of t he zo nes sh oul d not be
overlapped.

ZONES NUMBER:
SET LEFT LIMIT:
SET RIGHT LIMIT:
CLEAR ZONE:
EDIT ZONE LABEL :

Current zone selection

Left limit of the current zone

Right limit of the current zone

Delet the current zone

change the laben of current zone.

TIME RUNNING

You c an set u p the t imer t o sta r t a fun cti o n lik e
pr eset , tou r or pat ter n. Eac h day c an be se t 4
action.

AUTO TRACKING

Auto-Tracking can seach people or object with
hi gh spe ed an d low li ght p erfo rma n ce.

DAY: set current day
STATE : acti va t e AUTO-TR ACK ING on t his day
STA RT TI ME: se t the t ime fo r act iva tion
EN D TIME : set t he tim e for s top th e tra cki ng
SE NSIT IVE : set th e sen siti vit y for th e det ecti on
TRAKING ZOOM: activate auto-zoom
SE T LIMI T: se t the ma x. an gle fo r
the tracking.

18

6.OSD - Alarm Setting

7. Dome Address & Protocol

WINDOW BLANKING

WINDOW NUMBER 01
EDIT WINDOW
ENAB LE W INDOW O FF
CLEAR WINDOW
BACK
EXIT

ALARMS

Resume OFF

SEQUENCE 001

RESET DELEY 030

ALARM CONTACT N/O

ALARM SETTING

ARM SETTING

BACK

EXIT

ALARM SETTING

ALARM NUMBER 001

ALARM

ACTION TOUR

ACTIVATE AUX AUX1

ALARM PRIORITY LOW

BACK

EXIT

ARM SETTING

DAY SUN

ARM STATE OFF
ARM TIME N /A

UNARM TIME N/A
BACK
EXIT

Privacy Mask ( Window Blanking)

Privacy Mask is used to protect the privacy area not to be
displayed once the camera is pointed on, such as
ulevatory area or the operation desk of anATM machine.
It might be required for video surveillance application
depends on the local law regulation. The PTZ camera
supports up to 24 private masks. ( depends on installed
camera module, please contact your local sales
representative for more information)

Hitachi camera modules

Sony Camera modules:

ex cep t the 45 s eri es pro vid es onl y 8)

LG,CNB Camera modules:

WINDOW NUMBER:

EDIT WINDOW:

the keyboard. presse IRIS-OPEN to save.

ENABLE WINDOW:

CLEAR WINDOW:

Edit position of the mask by joystick of

Delete the mask

: 8 ma ski n g are a.

up t o 24 ma s kin g area (

no masking function.

Mask number

shows the mask on screen OFF

Alarms

RESUME: Continue the function on the camera , if it

was setting before the alarms.
RESET DELAY: How long the camera stay in Alarm

position.

ALARM CONTACT: Setting between N/C (normal Close)
or N/O (normal Open).

ALARM NUMBER: curent Alarm number.

ALARM ACTION: Setting for PRESET, SCAN, TOUR,

PAT 1-4, or NONE, if the camere inAlarm position.

ACTIVATE AUX:

activate. Select between AUX1, AUX2 (not connected)
or BOTH.

ALARM PRIORITY:

ARM SETTING: define the operation timer of the alarm

Setting Alarm Output, when Alarm is

define the priority of the alarm input.

Protocol setting

In order to establish a connection for
telemetric control with keyboard device. you
need to setup the dome address and protocol.

The PTZ cameras are capable with multiple
communication protocol. The setting can be
ch ange d thr ough t he DI P-S witc hes o n the re ar
side of the connector boards as Illustrated.

Sw1 Sw2

SW 1:

represent the domes address in binary form.

please refer to the list on next page for reference.

SW 2:

Used for protocol settting and baud rate.

DIP 1 to 6 : Protocol setting
DIP 7 and 8: Baud rate setting

Baud rate

DIP 7 DIP8

pl ease u se th e foll owi ng tab le fo r deta ils s e tup .

current pattern.

2400 bps 0 0

4800 bps 1 0

9600 bps 0 1

19200 bps 1 1

Protocol / DIP 1 2 3 4 5 6

B02 0 0 1 1 0 0

DIAMOND 1 0 0 1 0 0

HUNDA 1 0 1 1 0 0

KALATEL 0 1 0 1 0 0

LILIN 1 1 0 1 0 0

MOLYNX 0 0 1 0 0 0

PANASONIC 1 1 1 0 0 0

PELCO (D/P) 1 0 0 0 0 0

PHILIPS 0 0 0 0 0 1

SAE 0 1 0 0 0 0

SAMSUNG 0 0 0 1 0 0

SANTACHI 0 1 1 0 0 0

UNIVISION 0 1 0 0 0 1

VCL 1 1 0 0 0 0

19

Some products may not be available in your country, please contact our distributor for more details

VICON 1 0 1 0 0 0

AD 1 0 0 0 0 1

7. Address ID, 1 to 67

7.Address ID, 68 to 135

7. Address ID, 136 to 203

177

7. Address ID, 204 to 255

8. Specification

9. Motion Tracking

Indoor 18X Indoor 18x

Model

Signal Format

Scanning

Image Sensor

H. Resolution

Viewing Angle

Zoom

Min. Illumination

Focus

White Balance

Shutter Speed

Iris Control

Gain Control

Video Output

S/N Ratio

PTZ Characteristics

On-Screen Display

OSD Menu

Object Tracking

(only G70AT serie)

Communication

Preset Positions

Auto Pan

Tour / Sequence

Alarm inputs

Operating Environment

Power

25

Some products may not be available in your country, please contact our distributor for more details

Outdoor 18X Outdoor 18x

Outdoor 18X Outdoor 18x

48.0° (Wide end) 54.2° (Wide end)

18× Opt. / 12× Digital 26× Opt. / 12× Digital

0.7 Lux

(1/50 sec., Color)

-

Auto / Manual (ATW, Indoor, Outdoor, One Push WB, Manual WB)

Wide Dynamic Function (SB18WD/ SB26WD / SB36WD models)

360° PAN (0.4° ~320° per sec) / 90° Tilt (0.4°~150° per sec) with

Auto Flip/ Vario-Speed control* / Proportional & constant PT speed

Date/ Time/ Zoom Rate/ Temperature/ Zones/ Camera name

Setup/ Automation programming/ Password protection

4 progr. Tours with max 32 presets/ 4 Pattern up to 180s

with WDR

1/4 inch Ex-View CCD

470 TVL, 440K Pixels (PAL)/ 540 TVL (High Resolution)

Day: 0.7Lx

(1/50), 0.1Lx (1/3)

Night: 0.01Lx (1/3)

1 to 1/10,000 Sec. 1/3 to 1/10,000 Sec.

Auto / Manua/ Auto Slow Shutter

Auto / Manual (-3 to 28 dB, 2 dB steps, 16steps)

VBS: 1.0Vp-p (Sync Negative), Y / C Output

Manual activation / Preset triggering / Scheduled activation

RS-485, , coax16 Multiple protocol supported

Outdoor: -40℃ to 60℃ / IP66 weather protection

Indoor: / humidity up to 95%-10 5℃to 0℃

Tracking zone selection

Yes, between 2 presets

7 inputs / 2 output

24V AC / 24W(indoor) 48W(outdoor)

Indoor 26x Indoor 36x

Outdoor 26x Outdoor 36x

Outdoor 26x Outdoor 36x

with WDR with WDR

AU-G65-SB26

Day / Night Day / NightDay / Night

PAL / NTSC

Progressive

2.2° (Tele end)

Day: 1.0 Lux
(50IRE, F1.6)

Night: 0.01Lux

Auto / Manual

More than 50 dB

128 Presets

36× Opt. / 12× Digital

Night: 0.01Lx (1/3)

57.8° (Wide end)

1.7° (Tele end)2.8° (Tele end)

Day: 1.4Lx

(1/50), 0.1Lx (1/3)

Note: This option is only available if your Speed dome supported this function.

1. Enter the OSD menu with CALL 95

2. Go to the option Function Setting Auto Tracking→

AUTO TRACKING

DAY SUN

STATE ON
START TIME 0 0:00

END TIME 00:00
SENSITIVE LOW
TRACKING-ZOOM OFF
SET LEFT LIMIT
SET RIGHT LIMT
BACK
EXIT

AUTO TRACKING

Auto-Tracking can seach people or object with
hi gh spe ed an d low li ght p erfo rma nce.

DAY: set current day
STATE : acti va t e AUTO-TR ACK ING on t his day
START TIME: set the time for activation
EN D TIME : set t he tim e for s top th e tra cki ng
SE NSIT IVE : set th e sen siti vit y for th e det ecti on
TRAKING ZOOM: activate auto-zoom
SET LIMIT: set the max. angle for
the tracking.

Setting 1: Auto Tracking all the time

1. Step: Set on all „Day“ (Mon-Sun) with „ON“ on the
„State“ setting.

Setting 2: Auto Tracking on the certain time

1. Step: Set the desired „Day“ (Mon-Sun) with „ON“ on the
„State“ setting.

2. Step: Set the „Start Time“ and „End Time“

Setting 3: Auto Tracking on the certain Area

1. Step: Set the desired „Day“ (Mon-Sun) with „ON“ on the
„State“ setting. Set the „Time“, if it necessity.

2. Step: Set the „Left Limit“ and „Right Limit“

(The AT function will be stop, if the range of the
limit is reach)

Optional function can be use:

► .... Auto Zoom if the moving object is too small.

Tracking Zoom

► : Go to

Start/Stop Auto Tracking by Preset

„Function Setting“ Preset“ and set „Auto Tracking“

→→„

ON....... Start Auto Tracking function

OFF...... Stop Auto Tracking function

NONE .. No function

► ..... Start a function if the AT isn‘t moving (lost object)

Park Time

Go to „System setting“ Motion“ and set the „Park Time“

„

time (1-240min) and action(like Preset as a Start position)
to do, when the AT is on Idle.

Some products may not be available in your country, please contact our distributor for more details

26