AVUE HDMI-EC200 User Manual

HDMI EXTENDER OVER CAT5e/6/7

FEATURES

WHAT’S IN THE BOX

 1x Sender (TX) Unit

 1x Receiver (RX) Unit

 2x 5V Power Adapter

 User’s Manual

DIAGRAMS

OPERATION & CONNECTION

SPECIFICATIONS

DTS-HD/Dolby-trueHD/LPCM7.1/DTS/Dolby­AC3/DSD

HDMI Output

1080p/1080i/720p/576p/576i/480p/480i

Audio Output

LPCM7.1/DTS/Dolby-AC3/DSD

Max. Bandwidth

225Mhz

Max. Baud Rate

6.75Gbps

Input Video Signal

0.5 ~ 1.5 Volts p-p

Output DDC Signal

≤49.2feet or15m AWG26 HDMI standard cable

Max. Power

Consumption

Input: AC 50/60Hz 100V-240V
Output: DC4V/1A (TX/RX)

Operating Temp.

59° ~ 131° F or -15° ~ 55° C

Dimension L x W x H

82 x 44 x 22mm (TX/RX)

Weight

0.41 lb. or 195g

NOTES

HDMI-EC200

HDMI IN: Signal Source Input
HDMI OUT: Receiver to connect the HDTV or other display
DC 5V: 5V DC-DC Power Adapter interface

1. Connect one HDMI cable up to 50 feet between Sender (TX) unit

2. Connect one HDMI cable up to 50 feet between Receiver (RX) unit

3. Use a single CAT6/5e, up to 200 feet, to connect the Sender and Receiver

4. Connect the power adapter to Sender and Receiver unit.

 Supported Video Input: 1080p/1080i/720p/576p/576i/480p/480i @ 24/50/60fs
 Supported Video Output: 1080p/1080i/720p/576p/576i/480p/480i @ 24/50/60fs
 Supported Audio Formats: DTS-HD/Dolby-trueHD/LPCM7.1/DTS/Dolby-AC3/DSD
 Use single CAT6/5e cable up to 200 feet between sender and receiver units.
 Supports 3D
 LED status indicator
 No loss of quality
 Installs in minutes

CAT: Use single CAT cable to connect Sender and Receiver

Switcher: Reads EDID information of incompatible display source to adapt.

1. Connect power adaptor to TX unit.

2. Connect HDMI cable with output of TX to HDMI input of display.

3. Keep the display on and choose the matching HDMI input port.

4. Press Switcher button on TX to adapt to display. Status LED will turn green

when finished adapting from EDID information.

5. Take HDMI cable out and power off the TX.

Adapted EDID settings will take affect when powered on again.

NOTE: These steps also work for HDMI-DVI cable for DVI display.

Max. CAT-6 Length Up to 200 feet

HDMI Input 1080p/1080i/720p/576p/576i/480p/480i

Audio Input

600mA

Power Adapter

Please use these units as instructed to prolong their usefulness.

1. The units should be placed far from damp, high temperature, dusty, erosive, or

oxidative environment.

2. Avoid heavy shaking, hit, or fall.

3. Use original factory power adapter.

4. It is prohibited from touching the power adapter with wet hands.

5. Hold the adapter head and do no pull the power cord when not using the unit.

6. Unplug the power adapter when the units are not to be used for long periods.

7. Do not open the cover to touch the inside parts. There is no serviceable part.

Before powering on, please check the connecting cables carefully. Make sure that

#

Issue

Cause & Ways to Troubleshoot

1

No Power

1. Check the power adapter head is fully and

2. Check the power switch is on the ON status.

2

No Picture

1. Make sure that the TV is on and has been

5. Check the cables quality

3

Obscure Picture

1. Try again to connect the cable.

2. Use good quality HDMI cable.

all interfaces are normally connected. The table below is some common to issues
that may arise:

correctly inserted into the power socket.

connected with the unit.

2. Check if the signal source is on and well

connected.

3. Check the system connection quality.

4. Check if the line is all good quality.