AVUE AV676PIRW User Manual

AV676PIR - Black

AV676PIRW - White

Thank you for purchasing our product. Before attempting to connect
or operate this product, please read the instructions carefully before
use.

DESCRIPTION

AV676PIR(W) uses advanced imaging technology from
SONY IMX138 CMOS sensor to capture image resolution as
high as 720P@60FPS and outputs analog signal through
CVBS/BNC. It features 2D/3D adaptive noise reduction.
External button accesses camera’s OSD menu to set Motion
Detection, Privacy Zone, Digital Zoom, Digital Picture
Correction, Shutter, White Balance, and other imaging
features.

PRECAUTIONS

1. Use appropriate power supply.
The power input for AV676PIR(W) is DC12V. Using wrong power source will
damage the camera permanently.

2. Do not attempt to disassemble the camera.
There is not serviceable parts.

3. Handle the camera with care.
Avoid abusing the camera by striking, shaking, or other improper
handling.

4. Do not place the camera in the following locations:
a. Where temperature is lower than -4 ℉ or higher than 131 ℉;
b. Where humidity is higher than 90%.

5. Clean the CMOS faceplate with care.
Do not use strong detergents. Use a piece of lens tissue or cotton tipped
applicator and ethanol.

6. Do not attempt to aim the camera at the sun.
Aiming at the sun or other extremely bright objects causes smear to
appear irrespectively of whether the camera is operating or not. This can
damage the CMOS.

7. Do not put the camera in places with interference.
When this camera is installed near the equipment like wireless
communication device that emits strong electromagnetic field, some
irregularities such as noise on the monitor screen may happen.

FEATURES

● Sony IMX138 720P CMOS Sensor

● CVBS/BNC 960H/720P@60FPS Video Output

● True Day & Night

● Motion Detection, Privacy Zones

● Adaptive 2D/3D Noise Reduction

● Ingress Protection Rated IP66: Dust & Weather Proof

● OSD Menu & External Button menu access

PARTS INSTRUCTIONS

1. Ring Enclosure

2. Camera Holder

3. Base

4. Camera Lens

5. Wire Out Hole

6. Four install screws holes (on base)

www.avueinc.com

DIMENSION

CONNECTIONS

Use screwdriver to adjust zoom and focus.

SETUP

Camera Installation:

1. Unscrew the ring
enclosure, take it out.

2. Using the foam pat to
locate the holes in the
wall.

3. Drill 4 holes in the
position needed in
accordance with the holes
on the base. Push the
expansion bolt inside,
then screws the base to
the expansion bolt holes
loosely.

4. Get the wire out from the
wire out hole through the
base.

5. Screw tightly the base to
the wall.

6. Screw the enclosure to
the base with the ring
enclosure.

MENU

IMAGE ↩

3D-NR ↩
AE MODE
IMAGE ENHANCE ↩
FLIP
ZOOM IN

IRIS ↩
WB
MIRROR
BRIGHTNESS

DAY & NIGHT

AUTO
B&W

COLOR
EXTERNAL

ZONE MASKING ↩

STATUS
VERTICAL SIZE
VERTICAL MOVE

HORIZONTAL SIZE
HORIZONTAL MOVE

MOTION DETECTION ↩

STATUS
HORIZONTAL SIZE
HORIZONTAL MOVE

COLOR
VERTICAL SIZE
VERTICAL MOVE

VIDEO STANDARD

PAL

NTSC

LANGUAGE

ENGLISH

CHINESE

LOAD DEFAULT

SOFT VERSION

SAVE & EXIT

SPECIFICATIONS

Sensor

⅓” SONY IMX138 CMOS

Effective Pixels

1.3 Megapixels

Scanning System

2:1 Interlaced

Sync. System

Internal

Resolution

720P (equal to 1000TVL)

Lens

2.8-12mm Varifocal

White Balance

AUTO

Electronic Shutter

AUTO

OSD

Built-in with external access button

White Balance

AWB-PRO/AWB-TEMP/AWB-AI/AWB-GW/AWB-CCT

Backlight

Compensation (BLC)

ON/OFF/AUTO

Noise Reduction

3D Noise Reduction

Motion Detection

Off/On (4 Areas)

Privacy Zones

Off/On (8 Areas)

Day & Night

Auto / B&W / Exton / Color

S/N Ratio

> 50dB (AGC Off)

Video Output

1.0V p-p Composite Video Output, 75Ω

IR LED

36 pcs IR LED (⌀5mm/850nm)

IR Distance

100 Feet / 30 Meters

Min. Illumination

0 Lux (IR On)

Power Supply

DC 12V ± 10%

Power Consumption

300mA, 3.6W

Operating Temp.

-4 ~ 131 ℉ / -20 ~ 55 ℃

Dimension (⌀ x H)

⌀4.72 x 3.74 inches / ⌀120 x 95 mm

Weight

1.81 lb / 820g

www.avueinc.com