TFT-LCD TV
READ CAREFULLY
BEFORE OPERATION
USER MANUALUSER MANUAL
W150T
W150T
Before connecting the AC power cord to the DC adapter outlet ,make sure the
voltage designation of the LCD TV corresponds to the local electrical supply .
If you are unsure of your power supply , ask your local power company .
Never insert anything metallic into the cabinet openings of the LCD TV;
otherwise may cause the danger of electric shock.
To avoid electric shock, never touch the inside of the LCD TV / adapter.
Only a qualified technician should open the case of the LCD TV/adapter.
Never use your LCD TV/adapter when the power cord has been damaged .
Make sure there is nothing resting on the power cord, and keep the cord
away from places where people can trip over it .
Be sure to hold the plug, not the cord when disconnecting the adapter from
an electric socket.
CAUTION
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
TO PREVENT ELECTRICAL SHOCK.
DO NOT REMOVE THIS COVER. NO
USER- SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol indicates
dangerous voltage
inside the product that
presents a risk of electric
shock or personal injury.
This symbol indicates
important instructions
accompanying the
product.
Please read this manual carefully before using this product.
IMPORTANT SAFETY INSTRUCTIONS
Openings in the LCD TV/adapter cabinet are provided for ventilation.
To prevent overheating, these openings should not be blocked or covered.
Also, avoid using the LCD TV on a bed ,sofa ,rug, or other soft surface. As
this, may block the ventilation openings in the bottom of the cabinet. If you
put the LCD TV in a bookcase or some other airless space, be sure to provide
adequate ventilation.
Do not expose the LCD TV to extreme temperature conditions or to extreme
humidity conditions.
The apparatus should not be exposed to dripping or splashing and no objects
filled with liquids, such as vases, should be placed on the apparatus.
Do not clean the front with keton-type materials (e.g.Acetone ),ethyl alcohol,
toluene, ethy lacid, methyl, or chloride-these may damage the panel.
Locate your DC adapter near an easily accessible AC outlet.
If your LCD TV does not operate normally in particular, if there are any
unusual sounds or smells coming from it unplug it immediately and
contact an authorized dealer or service center.
High temperature can cause problems. Don t use your LCD TV in direct
sunlight, and keep it away from heaters, stoves, fireplaces, and other
sources of heat.
'
Unplug the DC adapter when it is going to be left unused for a long time .
To reduce the risk of fire or electric shock, and annoying interference, use the
recommended accessories only.
If the LCD TV is broken, do not try to repair it yourself. Contact qualified service
personnel.
Unplug your DC adapter from the AC outlet before any service.
Be sure the service technician uses authorized replacement parts or their equivalents. Unauthorized parts may cause fire, electrical shock, or other hazards.
Following any service or repair, be sure the service technician performs safety
checks to certify that your TFT-LCD TV is in a safe operating order.
The apparatus with CLASS I construction shall be connected to a MAINS
socket outlet with a protective earthing connection.
IMPORTANT SAFETY INSTRUCTIONS
CONTENT
AV and SCART SETUP
Video setting menu
17
EXTERNAL EQUIPMENT
Connecting diagram
4
LET'S START
Changing source operation
8
REMOTE CONTROL HANDSET
Remote buttons
5
Battery installation
7
TV MENU SETUP
Picture
Sound
TV setup Function
9
11
12
14
PANEL BUTTON FUNCTIONS
Panel control
2
3
Rear panel
INSTALLATION
Normal installation
1
TELETEXT FUNCTION
Teletext display
Mix mode
Page selection
Lock
Zoom in teletext
16
Index
Display mode
16
Colorized buttons
16
15
15
15
15
15
SPECIFICATIONS
Specifications
27
TROUBLE SHOOTING
Display troubleshooting
Sound and TV troubleshooting
26
26
DVB FUNCTION SETUP
General setup
22
DVB-T setup
Video setup
23
22
Password setup
25
DISPLAY MODE
Display mode
28
VGA SETUP
Picture
Sound
TV setup Function
18
19
20
21
1, Hook the tache (labeled A)of the kickstand onto the plate (labeled C).
2, Tighten the screws ( M4 10) through the ostium (labeled B).
3, Figure shows the finished installation. The kickstand can rotate 15 -degree.
Kickstand
Ostium
Rear viewing of LCD TV
1
1
1
INSTALLATION
NORMAL INSTALLATION
A
B
M4 10
Screw 1pcs
C
Hook
10
2
5
2
PANEL BUTTON FUNCTIONS
Indicator( )Indicator is red when in standby mode, green when working normally.
1
IR sensor window
2
Front panel
CH+/- (Increase or decrease channel number)
6
5
VOL+/-(Increase or decrease volume)
SOURCE (Enter to exit source menu)
7
4
SETUP (Enter or exit setup menu)
STANDBY (To switch between standby mode and power-on mode)
8
Left panel
9
Headphone jack
PANEL CONTROL
3
POWER(Turns on or off the power supply).
1 2
3
4
5
6
7
8
9
PANEL BUTTON FUNCTIONS
3
REAR PANEL
SCART input terminal
2
Composite video/audio input
4
3
12V DC input terminal
1
1
VGA input terminal
2
3
4
5
Coaxial digital audio output
5
7
PC audio input
6
COAXIAL
SCART
PC IN
VGA AUDIO
6
R input terminal
F
7
R cable
F
DVD or VCR player
RL
EXTERNAL EQUIPMENT
NOTE
CONNECTING DIAGRAM
You should connect all interconnecting cables BEFORE plugging in the power cord.
Power amplifier (with coaxial digital audio in)
4
COAXIAL
SCART
PC IN
VGA AUDIO
W150T
2 3
4
5
6
7
8 9
1
0
REMOTE CONTROLLER
5
REMOTE BUTTONS
Direct source buttons
1
Select signal source directly: TV, DVB, AV,
SCART.
Number button
2
To select program number.
OK button
6
To confirm the selections.
14
INDEX/PAGE+
To display main content page when playing
the teletext /browse the next page of teletext
in DVB mode (not support MHEG5).
15
SUBPAGE/PAGE-
To display the subpage of the teletext/browse
the previous page of teletext in DVB mode( not
support MHEG5).
16
REVEAL/EPG
Display the hidden teletext information
/ in DVB
mode
To display the program guide
.
17
CYAN
CYAN button.
SETUP
8
Enter or exit setup menu.
NICAM
Switch in NICAM,A2 and mono channel (It is
effective in TV signal input with NICAM or A2
function).
11
12
SOUND
To select different sound field modes: User,
Music, Film, News.
1
2
3
4
5
8
14
7
10
6
12
17
4
To set the sleep timer.
SLEEP
10
CHANNEL+/-
To increase or decrease program number in
TV/DVBmode.
7
Left/Right cursor(menu adjustment )
To move leftward/ rightward or adjust the
selected item in the menu, or adjust sound
volume (invalid in DVB mode).
13
HOLD/INFO
To stop teletext on current page/To display the
language and sound track in DVB mode.
18
YELLOW
YELLOW button.
3
RETURN
To exchange channel between the previous
program and the current program in TV and
DVB mode.
5
FAVORITE
Display your favorite channel list in DVB mode.
9
11
13
15
16
18
PICTURE
9
To select different picture modes: User,
Standard, Dynamic, Soft.
6
REMOTE CONTROLLER
SOURCE
To select input source: TV, DVB, AV, SCART,
VGA.
22
UP/DOWN cursor
To select upward/downward in the menu or
change the channel in TV/DVB mode.
23
To display TV and teletext in the same time
/Selects the subtitle language in DVB mode.
MIX/SUBT
30
Volume +/-
26
To increase or decrease sound volume.
RED button.
RED
33
22
23
TEXT/TEXT
29
To enable or disable the function of teletext.
GREEN
Green button.
34
DISPLAY
To display current source information.
24
33
26
25
27
STANDBY
19
To switch between standby mode and poweron mode.
34
32
31
29
30
28
21
TWO-DIGIT NUMBER BUTTON
To switch between one or two-digit program
number.
MUTE
Sound mute switch.
25
LANG
27
To switch the output language in DVB mode.
CANCEL/AUDIO
To cancel teletext/To change the audio
language and sound track in DVB mode.
31
28
SCAN
Long press the button to start scanning
automatically in TV/DVB mode.
SIZE/TV/
To magnify teletext page/To switch between
TV and Radio modes in DVB mode.
32
W150T
2 3
4
5
6
7
8 9
1
0
19
21
24
20
No function
20
7
REMOTE CONTROLLER
Remove the battery cover. Insert two SUM-4(AAA) batteries matching the -/+ polarities of
the battery to the -/+ marks inside the battery compartment, as in the following figure:
BATTERY LIFE
Generally speaking, the battery may be used for one year, but the battery life is also
related to the usage times and remote controller operation.
If the remote controller is still not operating when very near to the remote sensor window,
please replace the battery.
Please use SUM-4(AAA) battery.
NOTES
Never use rechargeable battery.
Never charge, short-circuit, disassemble and heat the battery, or throw it into fire.
Pay attention not to fall or knock the remote controller, which may cause damage or
function failure to it.
Do not use new and old battery together.
If electrolyte splashes into body, please clean it with water.
CAUTION
Please put the battery in a place children cannot access. If swallowed by accident,
please contact your local doctor immediately.
BATTERY INSTALLATION
When not using the remote controller for a long time, please take out the batteries to avoid
liquid leakage. Before replacing new batteries, please clean the electrolyte in the remote
controller.
Please confirm whether the accessories contain the power adapter.
Please make sure to use power adapter within the specification range, otherwise it will
cause damage.
POWER SUPPLY
Use the car adapter in the accessories, connect one end to the socket in you car, the
other to the DC socket in the TV.
The input voltage of the car adapter should be 12Volts.
LET'S START
You can change the input source by using the source Menu. Press [SOURCE] button or
[SOURCE] key to show the menu as follows:
The current source item is highlighted. Press [ ] button on the remote control or [ CH+
/CH- ] key on the left side of LCD TV to select different source, Press [ ] button, [VOL+
/VOL-] key or [OK] button to confirm your choice .
CHANGE SOURCE OPERATION
TV
DVB
AV
SCART
VGA
8
INDICATOR
STANDBY
STANDBY
After this unit is well fixed on the desk or on the wall, and the cords are well connected
for input and output, what you should do next is:
Firstly, connect the adapter to the LCD TV, and turn on the power switch then the unit will go
into standby mode, you can see the indicator turn red.
Secondly, press [STANDBY] key on the left side of the LCD TV or [STANDBY] button on the
remote control to make the unit switch into working mode, and you will see the indicator turns
green. Now you can enjoy all exciting features of the whole new product.
Power switch
2 3
4
5
6
1
Item
BRIGHTNESS
To adjust brightness.
CONTRAST
To adjust contrast.
SATURATION
To adjust color saturation.
This product can store up to 100-channel programs (0 99). You can scan and
store all of the channels through manual or automatic scan mode.
In TV mode, press [SETUP] button and the setup menu will show as follows:
Pressing [ ] button on the remote control,
you can select setup menu sections(setup menu
consist of
. Press [ ] or [OK]
button to enter this menu section.
" PICTURE " , " SOUND " , " TV
SETUP " , " FUNCTION ")
Press [ ] button on the remote control to select
the item, and then press [ ] button to adjust
parameters. Press [SETUP] button to return to
main menu sections.
Select " " and menu will show as follows:
Press [ ] button to select different items and
[ ] button to adjust them.
TV MENU SETUP
Description
TINT
To adjust picture tint, only valid in N 3.58/N 4.43/PAL60 and display
mode with V-scanning frequency equal to 60HZ (please refer to P28).
9
PICTURE
PICTURE
MODE
Can be changed between : "USER ", "STANDARD ", " DYNAMIC "
and "SOFT ".
TINT
PICTURE
BRIGHTNESS
SATURATION
CONTRAST
50
40
50
50
SELECT RETURN
SETUP
ENTER
OK
PICTURE MODE USER
PICTURE
SATURATION
CONTRAST
70
TINT
50
50
70
SHARPNESS
SELECT RETURN
SETUP
ADJUST
SHARPNESS
COLOR TEMP.
To adjust picture sharpness.
Select color temperature mode : "NORMAL ", " WARM "and "COOL ".
NORMAL
COLOR TEMP.
TV MENU SETUP
10
" " Means there are more items in this page, you can press [ ] button to select them.
NOTE
Select "BRIGHTNESS " to adjust it, the sub item will show as follows :
press [ ] button to adjust the value of brightness.
BRIGHTNESS
50
RETURN
SETUP
ADJUST
Item
BALANCE
TREBLE
To adjust balance of left and right channels.
To adjust bass.
To adjust treble.
Select " "and menu will show as follows:
TV MENU SETUP
BASS
Description
SOUND MODE
Can be changed between USER , , FILM ." " "MUSIC" " " and "NEWS"
11
SOUND
Press [ ] button to select different items and press [ ] button to adjust them. The
following are the descriptions of the sound item.
50
50
50
SOUND MODE
BASS
BALANCE
TREBLE
SOUND
USER
NICAM
MONO
NICAM
Nicam/A2 function is only valid in TV mode while current program coming with Nicam/A2
signal.
If you can receive Nicam/A2 signal, you can operate as follows to enjoy that.
You can select Nicam stereo, mono channel or bilingual through NICAM button on the remote
control. If Nicam/A2 signal is too weak, this unit will switch into mono channel automatically.
When selecting mono channel, "MONO" will show on screen; when selecting bilingual I,
"DUAL I " will show on screen; when selecting bilingual II, "DUAL I I " will show on screen
and when selecting stereo, " STEREO " will show on screen.
NOTES
Select the NICAM mode( please refer to the notes).
SELECT RETURN
SETUP
ENTER
OK
TV MENU SETUP
12
Press [ ] button to select different items and press [ ] button to adjust them.
Item
CHANNEL
To change the channel number.
CHANNEL EDIT
FINE TUNING
To adjust the channel frequency accurately to make the sound
and picture effect better.
MANUAL SEARCH
To scan programs manually.
Description
AUTO SEARCH
To scan programs and store all of them automatically.
Select " " and TV setup menu will show as follows:
TV SETUP
NOTES
To enter a submenu to set channel skip and channel swap.
Please refer to the next page.
TV SETUP
CHANNEL
COLOR SYSTEM
SOUND SYSTEM
FINE TUNING
AUTO SEARCH
1
AUTO
I
40.00MHZ
SELECT RETURN
SETUP
ENTER
OK
COLOR SYSTEM
SOUND SYSTEM
Can be changed between: "AUTO ", "PAL " and " SECAM ".
Can be changed between: "B/G ", "D/K " , " L " and " I ".
Which COLOR SYSTEM mode and SOUND SYSTEM mode to use is related to the
local TV broadcasting system.
""""
If the local system is SECAM L, the color system must be selected as "SECAM" and sound
system must be selected as "L".
TV SETUP
SOUND SYSTEM
FINE TUNING
AUTO SEARCH
I
40.00MHZ
MANUAL SEARCH
SELECT RETURN
SETUP
ADJUST
CHANNEL EDIT
Item
CHANNEL
Description
SKIP
SWAP
SAVE
To select current channel here.
To select "YES " or "NO ", you can select "YES " to make current
channel unaccessible while using [ ] button to browse
channels.
Select or enter the channel number directly to swap with current
channel.
Highlight this option and press the [OK] button to confirm the swap
function.
13
TV MENU SETUP
CHANNEL EDIT
SELECT RETURN
SETUP
ADJUST
SKIP
SWAP
SAVE
5
CHANNEL
NO
?
_ _
Select "CHANNEL EDIT " , the menu will show as follows:
AUTO SEARCH
112.25MHZ
RETURN
SETUP
FOUND: 3
VHF L
Select "AUTO SEARCH " , the searching menu will show as follows:
3
1
2
3
4
The number of programs have found.
The current searching frequency Band, 3 Bands in total: "VHF L" ,"VHF H"," UHF".
The current searching frequency.
4
During the searching, you can press [SETUP] button to stop it.
2
1
TV MENU SETUP
Press [ ] to select " " item and press [ ] button to enter the following section:
14
FUNCTION
You can setup system configuration here.
Description
LANGUAGE
TRANSPARENCY
RESET
Set OSD language.
To reset all value to default.
Press [ ] button to select different items and press [ ] button to adjust them.
Item
FUNCTION
LANGUAGE
ENGLISH
TRANSPARENCY
LEVEL 3
SLEEP
OFF
RESET
SELECT RETURN
SETUP
ENTER
OK
SLEEP
To set the sleep timer.
To adjust transparency of OSD. it can be change from OFF
to LEVEL6, 7 levels in total.
15
TELETEXT FUNCTION
Press [REVEAL] button to display the hidden teletext information. Press this button again
to cancel teletext information displaying.
DISPLAY MODE
COLORIZED BUTTONS (RED, YELLOW, GREEN, CYAN)
Select the corresponding teletext page through colorized buttons.
When teletext page shows, you may double zoom in to display this teletext page;
Press [SIZE] button to zoom in the upper half part of teletext page;
Press [SIZE] button again to enter the under half part of teletext page;
Press this button for the third time to return to original display mode.
ZOOM IN TELETEXT
16
User could press [SUBPAGE] button to select to the subpage of teletext.
SUBPAGE
If no signal input in TV, AV, SCART the screen will show a similar signal to the
following figure.
NOTE
AV and SCART SETUP
17
AV
NO SIGNAL
4:50
VIDEO SETTING MENU
This unit will go into standby mode automatically
with no signal input for 5 minutes.
The menu setup of AV/SCART modes is much the same as that of TV mode, except the
" " section is invalid and a bit difference in sound mode. It is not repeated here.
You can find it in preceding pages.
If the input channel is SCART, this unit will automatically recognise RGB or CVBS
signal of SCART; when normal RGB signal appears, this unit will automatically switch
into RGB display mode. For this unit is combined by multiple functions, when inserting
into SCART socket, it will not automatically switch into SCART mode. You have to
select SCART channel through [SOURCE] menu, that is a little difference with that of
others TV set.
With the VGA mode supported up to 1024*768@75Hz, and speakers built in, you can use
this unit as a multimedia PC monitor. When this unit works in VGA mode, the following setup
can be done.
Press [SETUP] button to enter main section. Press [ ] button to select sections and then
press [ ] button or [OK] button to enter. If all is done, please press [SETUP] button twice to
exit and your setup data will be saved automatically.
Press [ ] button to select " ", and press [ /OK] button to enter.
To adjust brightness of picture.
Item
Description
BRIGHTNESS
COLOR TEMPERATURE
CONTRAST
AUTO CONFIG
STATUS
Press [ ] button to adjust value of item.
To adjust contrast of picture.
Enter sub menu to adjust color temperature of picture. Press
[ /OK ] button to enter.(details refer to the next page)
Auto config horizontal/vertical position, phase and frequency.
Press [ /OK] button to activate.
The format of the input signal.
18
VGA SETUP
PICTURE
PICTURE
AUTO CONFIG
BRIGHTNESS
COLOR TEMPERATURE
CONTRAST
50
40
SELECT RETURN
SETUP
ENTER
OK
1024 X768 V:75 HZ
VGA SETUP
Here shows the color temperature sub menu.
19
Item
Description
COLOR TEMP.
RED
GREEN
BLUE
Select color temperature mode :"USER", "NORMAL", "WARM"
and "COOL".
Adjust red value of color temperature.
Adjust green value of color temperature.
Adjust blue value of color temperature.
SOUND
Press [ ] button to select " " and press [ /OK] button to enter.
The operation of sound section here is the same as that in TV mode except the NICAM
is invalid. Please refer to P11.
Press [ ] button to select item and press [ ] button to adjust the value of the item.
NOTE: The RED , GREEN , BLUE only can be adjusted in USER mode." "" """ ""
50
50
50
SOUND MODE
BASS
BALANCE
TREBLE
SOUND
USER
NICAM
MONO
SELECT RETURN
SETUP
ADJUST
COLOR TEMPERATURE
BLUE
GREEN
RED
50
SELECT RETURN
SETUP
50
50
ADJUST
NORMALCOLOR TEMP.
To adjust frequency.
VGA SETUP
20
MONITOR SETUP
Press [ ] button to select " " and press [ /OK] button to enter.
Item
Description
PHASE
FREQUENCY
H-POSITION
V-POSITION
To adjust phase.
To adjust screen horizontal position.
To adjust screen vertical position.
Press [ ] button to select different items and press [ ] button to adjust .
NOTE
VGA
NO SIGNAL
1:50
If you use this unit as a PC-monitor, This unit will go into sleep
mode with no signal input for in 2 minutes.
In this mode, the indicator will turn red, and the screen is turned
off. You can wake it up by waking up your PC .
MONITOR SETUP
PHASE
FREQUENCY
H-POSITION
V-POSITION
SELECT RETURN
SETUP
ENTER
OK
50
50
50
50
VGA SETUP
21
FUNCTION
Press [ ] button to select " ", and press [ /OK] button to enter.
Press [ ] button to select different items and press [ ] button to adjust .
Item
Description
LANGUAGE
TRANSPARENCY
RESET
Select OSD language .
To adjust transparency of OSD. it can be change from OFF
to LEVEL6, 7 levels in total.
Reset all value that related to picture and sound to default .
FUNCTION
LANGUAGE
ENGLISH
TRANSPARENCY
LEVEL 3
SLEEP
OFF
RESET
SELECT RETURN
SETUP
ENTER
OK
SLEEP
To set the sleep timer.
DVB FUNCTION SETUP
Turn on the TV, press [SOURCE] button to change source to DVB, then you can enjoy the
rich and colorful contents of Digital Video Broadcast!
In DVB mode, press [SETUP] button, then press [ ] button to choose DVB item ,the DVB
setup menu will be introduce as follow:
22
General Setup Page
TV Display
Wide
OSD Lang
ENG
Go To General Setup Page
TV Type
PAL
Default
GENERAL SETUP
1. TV Display: This item is used to set the output picture ratio of this unit.
Optional settings: Normal/PS, Normal/LB, Wide, Wide Squeeze; Default: Wide.
2. OSD language: This item is used to set the OSD language .
Optional settings: English; Default: English
3. TV Type: To set the output video system of this player.
Optional settings: PAL, Auto, NTSC; Default: PAL.
4. Default: This item is used to restore all settings to the default value except "Parental control"
and Password" in the setup menu."
VIDEO SETUP
Video Quality Setup
Hue 00
Saturation 00
Sharpness
Med
Contrast
00
Brightness
00
Go To Video Setup Page
Gamma
None
2. Brightness: This item is used to set the brightness of video outputs.
1. Sharpness: This item is used to set the sharpness of video outputs.
Optional settings: High, Medium, Low; Default: Med.
4. Gamma: This item is used to set the color temperature of video output.
Optional settings: High, Medium, Low, None ; Default: None
5. Hue: This item is used to set the hue of video outputs.
3. Contrast: This item is used to set the contrast of video outputs.
6. Saturation: This item is used to set the saturation of video outputs.
DVB
DVB
NOTE: Please don t do any operation during setting the value to default, or the unit may
work abnormally.
'
DVB FUNCTION SETUP
DVB- T Setup Page
Area
UK
Parental Age
Time Zone
Go To DVB - T Setup Page
DVB
DIS
DVB-T SETUP
The DVB-T Setup Page is composed of five parts: Area, Time Zone, parental Age, Antenna
power, Channel Setup.
Note : Press [ ] button to select different item, and press [OK] or [ ] button to enter it.
Press [ ] button to return to the previous menu or to exit the current menu .
Optional settings: Australia, Austria, Belgium, Denmark, Estonia, Germany, Spain, France,
Italy, Netherland, Taiwan, UK ,Others, Default: UK.
Note : you must set the correct area before searching channels.
You can choose the area of your country.
1. Area
To choose your time zone, it is set depending on your country. If you dont know the exact
time, please ask local time manage department.
Default: 00:00
2. Time zone
This item is used to set the parental control ratings .To prevent your children watching
undesired programmes.
Optional settings: 4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,Disable
Default: Disable
3. Parental age
5. Channel setup
This item is used to search channels, edit the channel list or your favourite channel list,
view program guide information, etc.
23
Antenna Power
Channel Setup
Channel Remap
Auto Scan
Start
Adjust Channel
Manual Scan
Auto Scan
DVB
Reserve Channel
Auto Scan
Connect the antenna to the RF socket on the TV as follows, then you can automatically
search channels without entering any other information.
Channel setup
Off
4. Antenna power
Turn on/off antenna power supply, optional settings: On, Off; Default: Off.
24
Press [SCAN] on remote control more than 3
seconds to auto scan.
Using the [ ] button to select the Auto Scan item,
and press [OK] or [ ] button to select Start item,
then press [OK] button;
A prompting message will be displayed to request that
you confirm, select OK and press the [OK] button to
confirm.
In the scan process, the scan result will be displayed in the Auto Scan window.
DVB FUNCTION SETUP
Note: If you press the [SETUP] button during scanning, the operation is stopped and a prompting
message will be displayed at the bottom of Auto Scan window. Select OK and press [OK]
button to abort auto scan operation, and the channels found until then will be saved. And
select Cancel and press [OK] button to return to auto scan process.
Wait while the TV searches for the channels, this may take a few minutes.
""
""
Once you press [OK] button to start auto search operation, all the saved channels will be
cleared.
You can scan channels manually by setting scan parameters.
1. In setup menu, select Manual Scan item using
the[ ]button, and press [OK] or [ ] button to
select Start item, then press [OK] button.
2. Use [ ] button or enter you desired frequency
to search directly.
3. Select Scan item to start manual scan operation.
4. The scan result will be displayed on the manual scan
window, you can save the found channels or delete them if the TV has the same program.
""
Manual scan
Manual Scan
Freq: 177500KHz
Status Found Channels
Scan
Auto Scan
Freq: 65000KHz
TV Total: 00
Radio Total: 00
Progress:
Status Found Channels
40%
You can change every channel position as you like in channel remap window.
Channel Remap
Adjust channel
You can set your favorite channel, set parental control age for some channels or skip
channel in Adjust Channel window.
1. Select channel using [ ] button , Press [RED] button to set this channel as one of
your favorite channels.
2. Select channel using [ ] button , if you don't like this channel press [GREEN] button
to skip it .
3. Select channel using [ ] button, press [YELLOW] button to set this channel as a
protected one, to prevent children dialog from watching the undesired program.
Note: If the password mode is set to be On, when you set a channel protected, a password
will be needed to inputted in the Protect Channel window. The default password is
000000.
You can set the time when the reminding signal should be displayed before the program
starts.
Press [EPG] button, then a program information list of current channel will be displayed in
a window, move the cursor to PROGRAM, then press [OK] button, a more detailed program
list will be displayed, move the cursor to the program which you want to watch, then press
[OK] button ,the program is saved in your reserved channel.
25
DVB FUNCTION SETUP
If you want to watch a special program on a channel at a later time, you can reserve it.
Then a reminding signal will be displayed on screen several minutes before it starts.
Reserve Channel
DVB
Tenestrial
EPG 002 FlowerGd 4Mbs
Channel FlowerGd 4Mbs
Program
DVB
Notify time
OK
03 min
Password : This item is used to set a six digit password to enable you to change the parental
control ratings or the protected channels..
Password Mode: To set whether parental control function or protected channels needs
a password, optional setting: On, Off; Default: On.
PASSWORD SETUP
Password: To change the password, default :000000.
Password Setup Page
Password Mode
On
Password
Go To Password Setup Page
DVB
Please check for causes of problems in accordance with the following chart before contacting
maintenance personnel.
Cannot power on
Please make sure the power cord is correctly connected
No sound
Please make sure the audio cord is correctly connected
Check volume
Volume too low
Check volume
If volume is still too low when adjusting volume to maximum,
please check whether the input device is correctly
Please make sure the antenna is well connected
Remote control failure
Check whether remote control battery is full charged
Whether battery installation is correct
Whether obstacles exists between remote control and the
unit's receiving window
Check whether receiving window has strong light
Symptom
Causes and Correction
Symptom
Causes and Correction
Black screen, power
indicator light off
Check whether the power cord is well connected, and
whether this unit is powered on
Check whether the signal cord of input device is well
connected
Check whether input device is powered on
Check whether the input device signal is in this unit's
specification
Check computer output mode: control panel-display-setup
If the setup does not accord with this unit's specification,
please change the display setup
Horizontal scanning frequency: 30kHz 75kHz
Max display mode:
1024X768 75 Hz@
Image display flicker,
unstable
~
Vertical scanning frequency: 50 Hz 75Hz
~
TROUBLESHOOTING
DISPLAY TROUBLESHOOTING
SOUND AND TV TROUBLESHOOTING
Snowy picture
26
Make sure there is nothing plugged into the headphone jack
27
SCART
W H D
DVB
Input connector
Frequency range (VHF/UHF)
Channel range(VHF/UHF)
IEC-Type, IEC 169-2, Female
174MHz~858MHz
7 & 8 Mhz
Normal
Standby mode
Less than
Power
VGA
Format
(Hz )
Ver scanning frequency
SUPPORTED PC INPUT MODE
31.5
70.0
DOS
640 350
25.17
720 400
31.5 70.0
28.32
DOS
640 480
31.5 60.0
25.18
DOS
640 480
37.9 72.0
31.50
VESA
640 480
37.5 75.0
31.50
VESA
800 600
35.1 56.2
36.00
VESA
800 600
37.9 60.0
40.00
VESA
800 600
48.1 72.0
50.00
VESA
800 600
46.9 75.0
49.50
VESA
Hor scanning frequency
(KHz)
Pixel frequency
To prolong this unit's service life, you are suggested to use power management function
of computer.
Because of the difference of display card output signal (especially non-standard signal
output), the display image may appear little disturbance which can be adjusted through
" AUTO CONFIG " in the "PICTURE" menu by users.
This product does not support the display mode not listed above. In order to achieve
the best display effect, please select the above-listed 12 display modes input signal.
DISPLAY MODE
Resolution
(MHz)
28
1024 768
48.4 60.0
65.00
VESA
1024 768
VESA
VESA
56.5
70.11
75.00
1024 768 60.0 75.0 78.75
NOTES
Please check the following accessories.
User manual
AV cord
Remote control and battery
Power adaptor
Operational
Manual
ACCESSORIES
Kickstand Kit
V0.0
5195887
Wall Mount Holder Kit (optional)
**
**
Automotive Power socket adapter
W150T
2 3
4
5
6
7
8 9
1
0
Loading...