Avtech IR Done Camera User Manual

669z

t503s_V0.9

IR Done Camera User Manual

The product image shown above may differ from the actual product.

Please use this camera with a DVR which supports HD video recording.

Please read the instructions thoroughly before using the product.

CCAAUUTTIIOONN

RRIISSKK OOFF EELLEECCTTRRIICC SSHHOOCCKK

CCAAUUTTIIOONN:

:

To reduce the risk of electric shock, do not expose this apparatus to rain or moisture.

Only operate this apparatus from the type of power source indicated on the label.

The company shall not be liable for any damages arising out of any improper use, even if we have been advised of the possibility of
such damages.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence
of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.

This exclamation point within an equilateral triangle is intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the literature accompanying the appliance.

ROHS Announcement
All lead-free products offered by the company comply with the requirements of the European law on the Restriction
of Hazardous Substances (RoHS) directive, which means our manufacture processes and products are strictly
“lead-free” and without the hazardous substances cited in the directive.

The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected
separately at the product end-of-life. This applies to your product and any peripherals marked with this symbol. Do
not dispose of these products as unsorted municipal waste.

CE Mark
This apparatus is manufactured to comply with the radio interference.

The company does not warrant that this manual will be uninterrupted or error-free. We reserve the right to revise or
remove any content in this manual at any time.

FEATURES

1. 1/2.8” CMOS Sensor with 1080P video output

2. With motorized 316-degree pan, the camera can achieve a wide range of view, giving users more
comprehensive control over the monitored site

3. Sequence setup with up to 16 preset points for area patrol

4. External alarm I/O device connection

5. WDR to increase image recognizability in overexposure and dark areas

6. Solid Light series featuring better overexposure prevention (Advanced Smart Light Control), automatic
adjustment of image brightness, and longer lifetime of LEDs

7. IR effective distance up to 15 meters for 24-hour surveillance

PACKAGE CONTENT

 IR camera  User manual  Accessory pack

DIMENSIONS*

*Dimensional Tolerance: ± 5mm

SPECIFICATIONS*

Pick-up Element 1/2.8" SONY CMOS image sensor
Number of Pixels 1936(H) × 1096(V)
Video Frame Rate 1080P@30fps / 1080P@25fps
Min. Illumination 0.1 Lux / F1.8, 0 Lux (IR LED ON)

S/N Ratio More than 48dB (AGC OFF)
Shutter Speed 1/10,000 ~ 1/7.5 (Slow shutter)
Lens f3.6mm / F1.8

Lens Angle 87° (Horizontal) / 46° (Vertical) / 104° (Diagonal)
IR LED 1 unit
IR Effective Distance Up to 15 meters

PIR Sensor YES
IR Shift YES
IRIS Mode AES

White Balance ATW
AGC Auto
WDR YES (120dB)

External alarm I/O YES (1 input / 1 output)
Operating Temperature 0℃ ~ 40℃
Video Output 1.0 Vp-p composite, 75Ω

Power Source (±10%) DC12V / 1A
Optional Peripherals Wall-mount bracket (PAVM542-BKT(B))

* The specifications are subject to change without notice.

INSTALLATION

Step 1: Separate the dome cover from the camera.

Step 2: Make sure the screw holes on the plate are aligned with the holes on the camera base.

If not, slightly loosen the two screws on the plate and rotate it.

Step 3: Mark the locations of the two screw holes on the ceiling or wall, and drill a hole for each on the ceiling

or wall.

The distance between your camera and the location you want to monitor should be 3 ~ 4 meters.

NOTE: An installation sticker could be downloaded from

www.surveillance-download.com/user/503_installation_sticker.pdf.

-- For cabling behind the ceiling or wall, mark the location for one more hole for the camera cable to
go through;

-- For cabling along the ceiling or wall, do as indicated below for the cable to go through.

Step 4: Fix the camera to the ceiling or wall with the supplied screws.

Step 5: Connect your camera to power.

Step 6: Tilt and rotate the lens itself to adjust the position and viewing angle of the camera, and fasten the two

screws on the plate to fix.

NOTE: You don’t need to manually pan this camera. For details, please refer to the section

“MOTORIZED PAN AND SEQUENCE SETUP”.

Step 7: Replace the dome cover back to the camera.

NOTE: Please wipe the inner part of the dome cover against the lens for clear images.