Avtech ErisStation VCS702-WM Quick Start Manual

Quick start guide

Model: VCS702-WM

ErisStation

bu sin ess pho nes .vt ec h.c om

Conference Phone
with Two Wireless Mics

Congratulations

on purchas ing your new VTech product.

For support, shopping, and everything new at VTech, visit
our website at http://businessphones.vtech.com or call
(US) 1-800-595-9511, (Canada) 1-800-267-7377.

Install battery to the wireless mic

Risk of explosion! Batteries should not be exposed to
excessive heat such as bright sunshine or fire.
Use only the supplied battery.

Risque d’explosion! Le bloc-piles ne doit pas être exposé à
la chaleur excessive telle que la lumière du soleil ou au feu.
N’utilisez que la pile incluse.

•

•

•

•

1. Plug the battery connector securely into the socket insidePlug the battery connector securely into the socket inside
the battery compartment. Insert the battery with the label
THIS SIDE UP facing up onto the battery compartment.

2. Slide the battery door until it clicks into place.

3. Place the wireless mics into the charging cradles until
they are flush.

Register the wireless mic

You should register your new wireless mic to the base unit
following the instructions below.

To register the wireless mic

As part of this process, all existing, broken, or lost wireless
mics will be deregistered first. Then, the base unit will
re-register the two wireless mics that are placed into the
charging cradles.

Before registration, unplug the telephone line cord from the
wall jack to make sure there are no incoming calls during
registration.

Gather the two wireless mics that are to be registered,
and then place them into the charging cradles.

Enter 331734 on the base unit when it is not in use,
and then press . The screen displays Please place all
wireless mics on cradle, then press ‘SELECT’.

Make sure both wireless mics are on the charging
cradles, and then press . The wireless mics enter the

deregistration mode, and the screen displays Processing....

After deregistration is complete, registration starts.
The screen displays Registering... 1 2. The number X
blinks while registering the X-th wireless mic. You hear a
confirmation tone when each wireless mic is registered.
When both wireless mics are registered, the base unit
displays Registration done.

1.

2.

3.

Charge the battery for 8 hours before use.
If the wireless mic unit becomes warm when the
battery is charging, it is normal.

•

•

After registration, plug the telephone line cord back into the
wall jack.

If registration fails, the base unit will display
Registration failed. Try again and
returns to idle. You hear an error tone. Remove
the wireless mics from the charging cradles and
place them back in. Repeat steps 1 to 3 to try
the entire registration process again.

If the screen does not display Registration
done after step 3, repeat steps 1 to 3 to try the
entire registration process again.

All wireless mics should always be kept on the
charging cradles during the whole registration
process. Any wireless mic that is registered
before but not put into the charging cradle will be
deregistered after the above operations.

Status indicators on the wireless mics flash red
and green alternately during registration.

To cancel registration, press . The base unit
displays Registration cancelled. If registration
is cancelled, some of the wireless mics may
be deregistered. To register them back to the
base unit, repeat steps 1 to 3 to try the entire
registration process again.

•

•

•

•

•

Specific ations are subjec t to change withou t notice.
© 2015 for VTech Commu nications, Inc.
All rights r eserved. 06/ 15. VCS702-WM_QSG_V1.0
Document o rder number: 96 -010673-010-100

3

FCC, ACTA and IC regulations

FCC Part 68 and ACTA

This equipment complies with Part 68 of the FCC rules and
with technical requirements adopted by the Administrative
Council for Terminal Attachments (ACTA). The label on
the back or bottom of this equipment contains, among
other things, a product identifier in the format US:
AAAEQ##TXXXX. This identifier must be provided to your
telephone service provider upon request.

The plug and jack used to connect this equipment to
premises wiring and the telephone network must comply
with the applicable Part 68 rules and technical requirements
adopted by ACTA. A compliant telephone cord and
modular plug is provided with this product. It is designed
to be connected to a compatible modular jack that is also
compliant. An RJ11 jack should normally be used for
connecting to a single line and an RJ14 jack for two lines.
See the installation instructions in the user’s manual.

The Ringer Equivalence Number (REN) is used to determine
how many devices you may connect to your telephone line
and still have them ring when you are called. The REN
for this product is encoded as the 6th and 7th characters
following the US: in the product identifier (e.g., if ## is 03, the
REN is 0.3). In most, but not all areas, the sum of all RENs
should be five (5.0) or less. For more information, please
contact your telephone service provider.

This equipment may not be used with Party Lines. If you
have specially wired alarm dialing equipment connected to
your telephone line, ensure the connection of this equipment
does not disable your alarm equipment. If you have questions
about what will disable the alarm equipment, consult your
telephone service provider or a qualified installer.

If this equipment is malfunctioning, it must be unplugged
from the modular jack until the problem has been corrected.
Repairs to this telephone equipment can only be made by the
manufacturer or its authorized agents. For repair procedures,
follow the instructions outlined under the Limited warranty.

If this equipment is causing harm to the telephone network,
the telephone service provider may temporarily discontinue
your telephone service. The telephone service provider is
required to notify you before interrupting service. If advance
notice is not practical, you will be notified as soon as possible.
You will be given the opportunity to correct the problem and
the telephone service provider is required to inform you of
your right to file a complaint with the FCC. Your telephone
service provider may make changes in its facilities, equipment,
operation, or procedures that could affect the proper
functioning of this product. The telephone service provider is
required to notify you if such changes are planned.

If this product is equipped with a corded or cordless handset,
it is hearing aid compatible.

If this product has memory dialing locations, you may choose
to store emergency telephone numbers (e.g., police, fire,
medical) in these locations. If you do store or test emergency
numbers, please:

Remain on the line and briefly explain the reason for the call
before hanging up.

Perform such activities in off-peak hours, such as early
morning or late evening.

FCC Part 15

This equipment has been tested and found to comply with
the requirements for a Class B digital device under Part 15 of
the Federal Communications Commission (FCC) rules. These
requirements are intended to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and
receiver.

Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician
for help.

Changes or modifications to this equipment not expressly
approved by the party responsible for compliance could void
the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation. Privacy of communications may not be
ensured when using this telephone.

•

•

•

•

To ensure safety of users, the FCC has established criteria
for the amount of radio frequency energy that can be safely
absorbed by a user or bystander according to the intended
usage of the product. This product has been tested and
found to comply with the FCC criteria. The wireless mic may
be safely held against the face of the user. The telephone
base shall be installed and used such that parts of the user’s
body other than the hands are maintained at a distance of
approximately 20 cm (8 inches) or more.

This Class B digital apparatus complies with Canadian
requirement:

CAN ICES-3 (B)/NMB-3(B)

The RBRC® seal

The RBRC® Seal means that the manufacturer is voluntarily
participating in an industry program to collect and recycle
nickel-metal hydride rechargeable batteries when taken out
of service within the United States. These batteries may be
taken to a participating local retailer of replacement batteries
or recycling center. Or you may call 1 (800) 8 BATTERY® for
locations accepting spent Ni-MH batteries.

RBRC® and 1 (800) 8 BATTERY®
are registered trademarks of the
Rechargeable Battery Recycling
Corporation.