Avtech DG1648, DG0824, DG0412 Quick Start Manual
240Z
DG1648, 0824, 0412 quick_V1.3
B
B
E
E
S
S
T
T
D
DII
G
GII
T
T
A
A
L
L
S
S
E
E
C
C
U
U
R
RII
T
T
Y
Y
G
G
U
U
A
A
R
R
D
D
S
S
E
E
R
RII
E
E
S
S
Please read instructions thoroughly before operation and retain it for future reference.
The image shown above may differ from the actual product appearance.
1
1. FRONT AND REAR PANELS
1.1 Front Panel
1) LED Indication
The following LEDs will be on when:
POWER: DVR is powered on.
STANDBY: DVR is powered off normally till the next time DVR is powered on.
HDD: HDD is reading or under recording.
HDD Full: HDD is full.
ALARM: The alarm is triggered.
TIMER: Timer recording is enabled.
PLAY: DVR is under playback status.
REC: DVR is under recording.
2) (USB port)
To quickly backup or upgrade firmware/OSD, you can insert a compatible USB flash drive into this USB port.
Before using the USB flash drive, please use your PC to format the USB flash drive as “FAT32” first.
Note: For the list of compatible USB flash drives, please refer to “APPENDIX 2 COMPATIBLE USB FLASH
DRIVE BRAND” in the manual.
3) EJECT
Press this button to open / close the DVD writer.
4) MENU
Press this button to enter / exit the quick start menu.
In the sub-layer of the advanced setting menu,
press this button to confirm the settings and go back to the upper layer.
5) ENTER
Confirm the password entering.
Under the advanced menu, use this button to confirm the settings and go back to the upper layer.
6) SLOW
Under the playback mode, press this button to slowly playback the recorded file (by 1/4 speed or 1/8 speed).
7) ZOOM
Press this button to enlarge the image of the selected channel.
8)
16CH: Press this button to show the 4 / 8 / 9 / 16 channel display modes.
8CH: Press this button to show the 4 / 8 / 9 channel display modes.
4CH: Press this button to show the 4 channel display mode.
9) SEQ
Full screen sequence (Indicated by the icon “ ” ):
When the DVR is under one channel display, press “SEQ” button the DVR will enter full screen sequence mode.
Press again to exit the sequence mode.
Quad screen sequence (Indicated by the icon “ ” ):
2
When the DVR is under quad channel display, press “SEQ” button the DVR will enter quad screen sequence
mode. Press again to exit the sequence mode.
10) (Audio)
Use these two buttons to select the live or playback sound of the audio channels.
Icon “ ” means: Live audio of the 1st audio channel / Icon “ ” means: Playback audio of the 1st audio channel
Icon “
” means: Live audio of the 2nd audio channel / Icon “ ” means: Playback audio of the 2nd audio channel
Icon “
” means: Live audio of the 3rd audio channel / Icon “ ” means: Playback audio of the 3rd audio channel
Icon “
” means: Live audio of the 4th audio channel / Icon “ ” means: Playback audio of the 4th audio channel
Icon “
” means: The audio channel is not selected.
Note: If you want to make a video backup with audio, please connect audio cameras to the channels
which support the audio function
For 16CH & 8CH DVR, the audio channels are CH1, CH2, CH3 and CH4.
For 4CH DVR, the audio channels are CH1 and CH2.
11) (PTZ)
Press these two buttons at the same time to enter / exit the PTZ control mode.
In the PTZ control mode (Indicated by the icon “ ”):
Zoom in: Press "＋" button ; Zoom out: Press "－" button
Adjust PTZ angle: Press "UP”, “DOWN”, “LEFT” or “RIGHT" buttons
12) 1 ~ 16 (for 16CH) / 1~8 (for 8CH) / 1~4 (for 4CH)
Press one of the buttons to select the channel to display.
13) LIST
To quick search the recorded files by event list, press this button to show all types of the event lists.
ALARM: List the information of the alarm-trigger-recorded files.
MANUAL: List the information of the manual-recorded files. The DVR will save one recorded file once any recording setting is changed
MOTION: List the information of the motion-trigger-recorded files.
SYSTEM: List the information of the system-recorded files. The DVR system will save one recorded file every one hour.
TIMER: List the information of the timer-recorded files.
14) SNAP
Please connect a USB drive first and then press “SNAP” button to take a snapshot picture of the current image on
the monitor.
15) (PLAY)
Press this button to playback the recorded video.
16) (PAUSE/UP/ +), ◄◄ (REW/LEFT), ►► (FF/RIGHT), ▓ (STOP/DOWN/ -)
Press one of these four buttons to move the cursor up/down/left/right.
Under the playback mode, press these buttons to pause / stop / fast rewind / fast forward the playback file.
Press ”UP/ +” or “DOWN/ -” button to change the setting in the menu.
17) POWER
Press “POWER” button long enough to turn on/off your DVR.
Loading...