Avtech AVC-756D, KPD678, AVC757, KPD677, AVC755 User Manual

...

Download

KD678_677_676_675_AC758D_757_756D_755_CD536_538_manual_V1.1

DIGITAL VIDEO RECORDER

USER MANUAL

Please read instructions thoroughly before operation and retain it for future reference.

IMPORTANT SAFEGUARD

Graphic Symbol Explanation

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

All lead-free products offered by the company comply with the requirements of the European law on the Restriction of Hazardous Substances (RoHS) directive, which means our manufacture processes and products are strictly “lead-free” and without the hazardous substances cited in the directive.

The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected separately at the product end-of-life. This applies to your product and any peripherals marked with this symbol. Do not dispose of these products as unsorted municipal waste. Contact your local dealer for procedures for recycling this equipment.

This apparatus is manufactured to comply with the radio interference requirements.

Disclaimer

We reserve the right to revise or remove any content in this manual at any time. We do not warrant or assume any legal liability or responsibility for the accuracy, completeness, or usefulness of this manual. For the actual display & operation, please refer to your DVR in hand. The content of this manual is subject to change without notice.

The product & company names mentioned herein may be the registered trademarks or tradenames of their respective owners.

MPEG4 Licensing

THIS PRODUCT IS LICENSED UNDER THE MPEG-4 VISUAL PATENT PORTFOLIO LICENSE FOR THE PERSONAL AND NON-COMMERCIAL USE OF A CONSUMER FOR (i) ENCODING VIDEO IN COMPLIANCE WITH THE MPEG-4 VISUAL STANDARD (“MPEG-4 VIDEO”) AND/OR (ii) DECODING MPEG-4 VIDEO THAT WAS ENCODED BY A CONSUMER ENGAGED IN A PERSONAL AND NON-COMMERCIAL ACTIVITY AND/OR WAS OBTAINED FROM A VIDEO PROVIDER LICENSED BY MPEG LA TO PROVIDE MPEG-4 VIDEO. NO LICENSE IS GRANTED OR SHALL BE IMPLIED FOR ANY OTHER USE. ADDITIONAL INFORMATION INCLUDING THAT RELATING TO PROMOTIONAL INTERNAL AND COMMERCIAL USES AND LICENSING MAY BE OBTAINED FROM MPEG LA, LLC. SEE HTTP://WWW.MPEGLA.COM.

GPL Licensing

This product contains codes which are developed by Third-Party-Companies and which are subject to the GNU General

Public License (“GPL”) or the GNU Lesser Public License (“LGPL”).

The GPL Code used in this product is released without warranty and is subject to the copyright of the corresponding

author.

Further source codes which are subject to the GPL-licenses are available upon request.

We are pleased to provide our modifications to the Linux Kernel, as well as a few new commands, and some tools to get

you into the code. The codes are provided on the FTP site, and please download them from the following site or you can refer to your distributor:

ftp://ftp.dvrtw.com.tw/GPL/AV071/

Version

Firmware: 1055-1015-1010-1023-1007 (For 16CH Models) / 1030-1015-1010-1023-1007 (For 8CH Models) Video Viewer: 0114

CAUTION:

To reduce the risk of electric shock, do not expose this apparatus to rain or moisture.

Only operate this apparatus from the type of power source indicated on the label.

The company shall not be liable for any damages arising out of any improper use,

even if we have been advised of the possibility of such damages.

CCAAUUTTIIOONN

RRIISSKK OOFF EELLEECCTTRRIICC SSHHOOCCKK

TABLE OF CONTENTS

1. SPECIAL NOTES .....................................................................................................................................................................................................1

2. FRONT AND REAR PANEL......................................................................................................................................................................................3

2.1. Front Panel .....................................................................................................................................................................................................3

2.2. Rear Panel...................................................................................................................................................................................................... 4

3. CONNECTION AND SETUP ....................................................................................................................................................................................6

3.1. HDD Installation.............................................................................................................................................................................................. 6

3.2. Camera Connection........................................................................................................................................................................................ 7

3.3. Optional Peripheral Connection (Selected models only)................................................................................................................................ 7

3.4. Power Setup ...................................................................................................................................................................................................7

3.5. Date and Time Setting.................................................................................................................................................................................... 7

3.6. Password Setting............................................................................................................................................................................................ 8

3.7. Record Setting................................................................................................................................................................................................ 8

4. BASIC OPERATION.................................................................................................................................................................................................9

4.1 Live Page......................................................................................................................................................................................................... 9

4.2. Recording .......................................................................................................................................................................................................9

4.3. Playback ....................................................................................................................................................................................................... 10

Via DVR........................................................................................................................................................................................................ 10

Via Supplied Software “Video Viewer” ......................................................................................................................................................... 10

4.4. Search .......................................................................................................................................................................................................... 11

Via Supplied Software “Video Viewer” ......................................................................................................................................................... 11

4.5. Firmware / OSD Upgrade ............................................................................................................................................................................. 11

5. ADVANCED OPERATION ...................................................................................................................................................................................... 13

5.1. QUICK SEARCH ..........................................................................................................................................................................................13

5.2. RECORD ......................................................................................................................................................................................................13

5.2.1. Quick record setting ...........................................................................................................................................................................13

5.2.2. Detailed record setting .......................................................................................................................................................................13

5.3. TIMER........................................................................................................................................................................................................... 14

5.4. DETECTION.................................................................................................................................................................................................15

5.4.1 For Model 1 & 3................................................................................................................................................................................... 15

5.4.2 For Model 2 & 4................................................................................................................................................................................... 16

5.5. REMOTE ......................................................................................................................................................................................................17

5.6. SYSTEM INFO .............................................................................................................................................................................................17

5.7. NETWORK ...................................................................................................................................................................................................18

5.7.1. STATIC ...............................................................................................................................................................................................18

5.7.2. PPPOE ...............................................................................................................................................................................................19

5.7.3. DHCP .................................................................................................................................................................................................20

5.8. BACKUP.......................................................................................................................................................................................................20

5.8.1. USB BACKUP .................................................................................................................................................................................... 20

5.8.2. DISK BACKUP (Selected models only) .............................................................................................................................................21

6. REMOTE OPERATION...........................................................................................................................................................................................23

6.1. Video Viewer.................................................................................................................................................................................................23

6.1.1. Installation & Network Connection ..................................................................................................................................................... 23

6.1.2. Control Panel...................................................................................................................................................................................... 24

6.1.3. General Operation.............................................................................................................................................................................. 25

6.2. IE Web Browser............................................................................................................................................................................................ 28

6.3. QuickTime Player .........................................................................................................................................................................................30

APPENDIX 1 PIN CONFIGURATION.........................................................................................................................................................................31

APPENDIX 2 TROUBLESHOOTING .........................................................................................................................................................................33

APPENDIX 3 COMPATIBLE USB FLASH DRIVE LIST.............................................................................................................................................34

APPENDIX 4 COMPATIBLE SATA HDD LIST............................................................................................................................................................35

APPENDIX 5 COMPATIBLE USB DVD WRITER LIST.............................................................................................................................................. 36

APPENDIX 6 RS485 PROTOCOL .............................................................................................................................................................................37

APPENDIX 7 SPECIFICATIONS................................................................................................................................................................................ 38

APPENDIX 8 RECORDING TIME TABLE.................................................................................................................................................................. 42

APPENDIX 9 DVR BATTERY REPLACEMENT......................................................................................................................................................... 44

SPECIAL NOTES

1. SPECIAL NOTES

 Remote Surveillance

1). This DVR series supports remote independent operation, and the image transmission per channel is

independent at the remote site. Therefore, during the remote surveillance, the image transmission may not be

so fluent when you’re viewing four channels or more at the same time.

2). During the remote surveillance, you can only switch the channel display when you are in DVR Control (

You’re not allowed to enter the DVR menu.

3). When you click snapshot to take a snapshot of the current view, each channel will have one image file.

The snapshot will be saved in the path you specified in “Record Setting”.

4). You can choose the single channel to watch when you are playback the record.

5). The channel title will not be shown when the user level for remote login is “guest”.

 VGA Output Resolution Support

Some models have VGA interface built-in, and users are allowed to change the resolution depending on their

display monitor.

Go to “ADVANCE”  “DISPLAY”, and move to “VGA OUTPUT” to select the VGA resolution you want. There are

seven options as follows:

1). 800 x 600 2). 1024 x 768 (default) 3). 1280 x 1024

4). 1440 x 900 5). 1400 x 1050 6). 1680 x 1050

7). 1600 x 1200

Note: To have the best image quality on your LCD monitor, make sure (1) the selected DVR VGA output

resolution is supported by your monitor, and (2) the VGA output settings on both the LCD monitor and DVR are consistent. If the image is not positioned or scaled properly, please go to your monitor’s menu for adjustment. For details, please refer to the user manual of your LCD monitor.

 Power Supply

To ensure that your DVR works constantly and properly, it's recommended to use an UPS, Uninterruptible Power

Supply, for continuously operation. (Optional)

 HDD Scanning & Formatting

When a HDD is connected for the first time and the DVR is turned on, the DVR will automatically detect & format

the HDD as needed. At the same time, the DVR will also scan the HDD for any bad sector, and use the good ones

for recording and data storage. It takes about eight minutes for a 1TB HDD to finish the whole process, and the

actual time needed varies based on different HDD capacity.

When the DVR is rebooted, the DVR will scan the HDD for any bad sector, and use the good ones for recording

and data storage. It takes about three minutes for a 1TB HDD to finish the whole process, and the actual time

needed varies based on different HDD capacity.

 USB DVD Writer Support

USB DVD writer connection is only supported for the selected models to have disk backup function.

To know whether your DVR supports USB DVD writer connection, please refer to “APPENDIX 7

SPECIFICATIONS” at page 38.

To know the compatible USB DVD writer list, please refer to “APPENDIX 5 COMPATIBLE USB DVD WRITER

LIST” at page 36.

To know how to use a USB DVD writer for video backup, please refer to “5.8.2. DISK BACKUP” at page 21.

SPECIAL NOTES

 DVR Battery Replacement

DVR time might reset after the disconnecting of the DVR power, for example, caused by a power outage, because

the DVR battery is low or even running out of power.

For details about battery replacement, please refer to “APPENDIX 9 DVR BATTERY REPLACEMENT” at page

44.

FRONT AND REAR PANEL

2. FRONT AND REAR PANEL

2.1. Front Panel

1) LED Indicators

POWER : DVR is powered on.

HDD : HDD is reading or recording.

ALARM : An alarm is triggered (Selected models only).

TIMER : Timer recording is on.

PLAY : Under playback status.

2) MENU

Press to enter the main menu.

3) ENTER

Press to confirm the setting.

4) LIST

To quick search the recorded files by event, press this button to show all types of the event lists.

Select one of the event list and press “ENTER” to playback the selected file.

5) SLOW

Under the playback mode, press to slowly playback the recorded file.

6) ZOOM

In the live or playback mode, press to enlarge the image of the selected channel.

7) 16CH: Press to show the 4 / 9 / 16 channel display modes.

8CH: Press to show the 4 / 9 channel display modes.

8) SEQ

Press to switch the channel display one by one, and press again to quit.

Note: When channel sequence display is on, the channel(s) with video loss and covert recording will be

skipped.

9) POWER or

Press long enough to turn on/off your DVR.

Note: Under the recording mode, please stop recording before turning off your DVR.

Note: To ensure that your DVR works constantly and properly, it's recommended to use an UPS,

Uninterruptible Power Supply, for continuously operation. (Optional)

10) 1~16 / 1~8

Press one of the buttons to select the channel to display.

11) PLAY

Press to play the recorded video.

12) S (PAUSE / +), T (STOP/ -), W (REW), X (FF)

Press one of these four buttons to move up/down/left/right.

Under the playback mode, press these buttons to pause / stop / fast rewind / fast forward the playback file. Under the setting mode, press ” S” or “T” to change the setting in the menu.

FRONT AND REAR PANEL

13) AUDIO (SEQ + )

Press SEQ + simultaneously to select the audio channel you want for listening to the live audio (in the live mode) or playback audio (in the playback mode).

14) PTZ (SLOW + ZOOM)

Press these two buttons at the same time to enter / exit the PTZ control mode.

15) USB port

To quickly backup or upgrade firmware/OSD, you can insert a compatible USB flash drive into this USB port.

Before using the USB flash drive, please use your PC to format the USB flash drive as “FAT32” first.

16) EJECT (Selected models only)

Press to open / close the built-in DVD Writer.

17) “MENU” + “ENTER” (Key lock)

Press these two buttons at the same time to lock keys on the DVR front panel.

Press any button on the DVR front panel and enter the DVR password to exit the key lock mode.

2.2. Rear Panel

1) INPUT (1 ~ 16CH / 1 ~ 8CH)

INPUT: Connect to video sources, such as cameras.

Note: If you want to make a video backup with audio, please make sure whether your DVR supports the

audio function, and connect audio cameras to the channels which support the audio function.

2) MONITOR

Connect to a CRT monitor for video output.

3) Audio IN

Connect to audio sources, such as cameras equipped with the audio function.

Please get to know whether your DVR supports the audio function, and how many audio inputs are supported

first.

Note: Depending on the model you have, this DVR series supports UP TO FOUR audio-in channels, which

are Audio 1, Audio 2, Audio 3 and Audio 4 accordingly, and the audio data will be recorded with the video data of CH1, CH2, CH3 and CH4 respectively. For example, if your DVR supports two audio-in, its audio channels will be Audio 1 and Audio 2. When you playback CH1, you will also hear the audio recording of Audio 1.

4) Audio OUT

Connect to an audio device, such as a microphone or speaker.

Note: Depending on the model you have, this DVR series supports UP TO TWO audio-out channels.

Please get to know whether your DVR supports the audio function, and how many audio outputs are supported first.

5) USB (Selected models only)

To quickly backup or upgrade firmware/OSD, you can insert a compatible USB flash drive into this USB port.

Before using the USB flash drive, please use your PC to format the USB flash drive as “FAT32” first.

6) IR

Connect the IR receiver for remote control (IR receiver optional).

7) EXTERNAL I/O

Insert the supplied 25 PIN DSUB to this port for connecting external devices (external alarm, PTZ camera, etc).

FRONT AND REAR PANEL

For detailed I/O port PIN configuration, please refer to “APPENDIX 1 PIN CONFIGURATION” at page 31.

8) VGA (Selected models only)

Connect to a LCD monitor directly.

Note: To select the suitable VGA resolution, please go to “ADVANCE”  “DISPLAY”  “VGA OUTPUT”.

9) LAN

Connect to Internet by LAN cable.

10) LINK ACT.

When your DVR is connected to the Internet, this LED will be on.

11) DC 19V

Connect to the supplied adapter.

CONNECTION AND SETUP

3. CONNECTION AND SETUP

3.1. HDD Installation

The HDD must be installed before the DVR is turned on. The steps below are for your reference only. The actual

installation process may vary depending on different models and situations.

 For Model 1 ~ 4

Step 1: Loose the screws on the upper cover and open the upper cover of the DVR.

Note: The DVR cover is made of metal. Please be careful with its edge when you remove the cover.

Step 2: Find the HDD brackets supplied within the sales package,

two L-shape brackets for each HDD.

Step 3: Get a compatible HDD, and align the screw holes of the

bracket with the HDD’s screw holes. Make sure the PCB

side of the HDD is facing up. Then, fasten the HDD to the

brackets.

Step 4: Connect the power connector and data bus connector to

the HDD.

Step 5: Find the screw holes on the DVR base, and fasten the

brackets to the DVR base.

Step 6: Close the upper cover of the DVR, and fasten all the screws you loosened in Step 1.

 For Model 6 & 8

Step 1: Loose the screws on the upper cover and open the upper cover of the DVR.

Note: The DVR cover is made of metal. Please be careful with its edge when you remove the cover.

Step 2: There are two HDD brackets for this DVR as indicated on

the right picture.

2-1 To install on the first bracket

Remove the bracket, and align the screw holes of the

bracket with the HDD’s screw holes. Make sure the PCB

side of the HDD is facing up.

Fasten the HDD to the bracket, and connect the power

connector and data bus connector to the HDD. Then,

replace the bracket to DVR.

2-2 To install on the second bracket

Connect the power connector and data bus connector to

the HDD.

When connecting the power cable, make sure the cable is

passed through the power cable of DVD writer. This is to

prevent the HDD power cable from interfering with the fan

spinning.

Align the screw holes of the bracket with the HDD’s screw

holes. Make sure the PCB side of the HDD is facing up.

Then, fasten the HDD to the bracket.

CONNECTION AND SETUP

Note: Make sure the HDD power cable is connected to the WHITE jack on the DVR mainboard as shown

below. The black jack is reserved for DVD writer installation.

Step 3: Close the upper cover of the DVR, and fasten all the screws you loosened in Step 1.

Note: When a HDD is connected for the first time and the DVR is turned on, the DVR will automatically

detect & format the HDD as needed. At the same time, the DVR will also scan the HDD for any bad sector, and use the good ones for recording and data storage. It takes about eight minutes for a 1TB HDD to finish the whole process, and the actual time needed varies based on different HDD capacity.

3.2. Camera Connection

The cameras must be connected and power-supplied. And then connect the camera video output to the DVR

video input port with a coaxial cable or RCA lines with BNC connectors. The DVR will automatically detect the

video system of the connected camera(s) (NTSC / PAL), and switch itself to the correct system.

1) Power connection

Connect the camera with indicated power supply.

2) Video cable connection

Connect the camera video output to the DVR video input port with a coaxial cable or RCA line with BNC

connector.

3) Audio cable connection

Connect the camera audio output to the DVR audio input port with a coaxial cable or RCA line with BNC

connector.

4) Camera Setup (PTZ cameras only)

For detailed camera title, ID, protocol and baud rate setup, please refer to “5.5. REMOTE” at page 17.

3.3. Optional Peripheral Connection (Selected models only)

Depending on the DVR model you have, this DVR series may support to connect other peripherals. For detailed

connection, please refer to their own user manuals.

3.4. Power Setup

This device should be operated only with the type of power source indicated on the manufacturer’s label. Connect

the indicated AC power cord to the power adapter, and plug into an electrical outlet. The power LED will be on.

Note: To ensure that your DVR works constantly and properly, it's recommended to use an UPS,

Uninterruptible Power Supply (Optional), for continuously operation.

3.5. Date and Time Setting

Before using your DVR, please set the date and time on your DVR first.

CONNECTION AND SETUP

Press “MENU” and enter the password to go to the menu list. The default admin password is 0000. Move to

“DATE” and you can set the date / time / daylight saving in the “DATE” menu list.

Note: Please DO NOT change the date or time of your DVR after the recording function is activated.

Otherwise, the recorded data will be disordered and you will not be able to find the recorded file to backup by time search. If users change the date or time accidentally when the recording function is activated, it’s recommended to clear all HDD data, and start recording again.

3.6. Password Setting

Press “MENU” and enter the password to go to the menu list. Then, move to “ADVANCE” to enter the advanced

setting menu.

In the “ADVANCE” menu, move to “SYSTEM INFO”. Select “PASSWORD” and press “ENTER” to enter the

submenu to set the password (four digits). The default admin password is 0000.

3.7. Record Setting

By defaults, the record function is activated when the DVR is powered on and a camera is connected.

To change the record settings, press “MENU” and enter the password to go to the menu list. Then, move to “ADVANCE”  “RECORD” to enter the advanced setting menu. You can set the image size, image quality and the

image per second for recording.

For details, please refer to “5.2. RECORD” at page 13.

BASIC OPERATION

4. BASIC OPERATION

4.1 Live Page

Depending on the DVR you have, you may see the following live view screen with status icons.

Icon Function Icon Function Icon Function Icon Function

Key lock

Key unlock

The 1st live audio

channel

The 2nd live audio

channel

3rd live audio channel

4th live audio channel

The 1st playback

audio channel

The 2nd playback

audio channel

The 3

playback

audio channel

The 4

playback audio

channel

Audio channel

unselected

Digital zoom mode

Digital zoom

unselected

HDD overwrite Timer recording

Motion

Recording

Alarm

R.E.T.R. on

(Selected models only)

R.E.T.R. delay

(Selected models only)

4.2. Recording

When the recording and the pre-alarm function are activated, this device will overwrite 8GB data from the oldest

for continuous recording without notice.

1) Manual Recording Icon

By defaults, when the DVR is properly connected with cameras and the HDD is installed, you can see “ ”

(recording) on the screen.

2) Event Recording Icon

When the motion / alarm detection is activated, once motion or external alarm happens, you will see “ ” (motion) or “ ” (external alarm) on the screen.

3) Timer Recording Icon

When the timer record is activated, you will see the LED light of “Timer” is on, and “ ” (timer) on the screen.

BASIC OPERATION

4.3. Playback

Via DVR

Press “PLAY” on the DVR control panel, and the device will playback the latest recorded video.

You could only watch 4-channel playback images at the same time. If you want to watch other channels, press button on the front panel to show the next 4-channel display.

Note: There must be at least 8192 images of recorded data for playback to work properly. If not, the

device will stop playback. For example, if the IPS is set to 30, the recording time should be at least 273 seconds (8192 images / 30 IPS) for the playback to work properly.

1) Fast Forward / Fast Rewind

You can increase the speed for fast forward and rewind on this device. In the playback mode:

Press “FF“ once to get 4X speed forward and press twice to get 8X speed, etc. And the maximum speed is 32X.

Press “REW“ once to get 4X speed rewind and press twice to get 8X speed, etc. And the maximum speed is 32X.

Note: During playback, the image size of the recorded data (FRAME, FIELD or CIF) will be shown on the

screen.

2) Pause / Image Jog

Press “PAUSE” to pause the playback.

In the pause mode:

Press “►” once to get one frame forward.

Press “◄” once to get one frame rewind.

3) Stop

Press “STOP” under the playback mode, and the screen of this device will return to live monitoring mode.

4) Slow Playback

Press “SLOW” to get 1/4X speed playback and press twice to get 1/8X speed playback.

5) Audio Playback

In the playback mode, press SEQ + to select the audio channel you want for audio playback.

Playback audio of the 1st audio channel

Playback audio of the 2nd audio channel

Playback audio of the 3rd audio channel

Playback audio of the 4th audio channel

The audio channel is not selected.

Note: If you want to make a video backup with audio, please make sure whether your DVR supports the

audio function, and connect audio cameras to the channels which support the audio function.

Via Supplied Software “Video Viewer”

In DVR Control

Click on the menu bar to show the DVR control panel, and click . A channel selection window will pop up, and you and select the channel and time within which includes the images you want to see.

BASIC OPERATION

Then, click “Play” to immediately start playback.

4.4. Search

Via DVR

1) Full Event Search

Press “LIST” to show the list for all types of the recorded files. Choose the item you want to see and press

“ENTER” to start playback.

2) Search by Time

Press “MENU” to enter the menu list, and go to “ADVANCE”  “EVENT LOG”. Move to “QUICK SEARCH”, and

press “ENTER” to enter the quick time search menu. You can search any specific events by time (Year / Month /

Day / Hour / Min) and directly play the file you find.

Via Supplied Software “Video Viewer”

Search by Event via the Supplied Software “Video Viewer”

Click on the menu bar, and click to enter the “Status List” page. Select the “Record” tab to show all the recordings, or sort the list by time or event.

Select a log from the list, and click “Play”, or double-click the selected log. A channel selection window will pop up,

and you can select the channel you want to see from the drop-down list.

Then, click “Play” to immediately start playback.

4.5. Firmware / OSD Upgrade

1) By using USB flash drive

Step 1. Format the USB memory device as FAT32 format first.

Step 2. Get the upgrade files from your distributor and save the upgrade files in your USB flash device (do not

change the file name).

Step 3. Insert your USB flash drive into the USB port. Wait till the DVR detects your USB flash drive. Step 4. Press “MENU”, and move to “ADVANCE”  “SYSTEM INFO”. Select “UPGRADE”  “START”, and press

“ENTER”.

Step 5. Select “YES”, and press “ENTER” again to confirm upgrade.

2) By using the supplied software “Video Viewer”

Step 1. Save the upgrade files at your PC (do not change the file name), and log into Video Viewer.

Step 2. Click “

” (Miscellaneous Control) to show the miscellaneous control panel. In the miscellaneous control

BASIC OPERATION

panel, click “ ” (Tools) on the miscellaneous control panel to enter the upgrade window.

Step 3. Enter the user name, password, IP address and port number of the DVR.

Step 4. In “Update Server”, click “Firmware” or “Language” tab as needed, and click “Add” to select the firmware

or OSD files to upgrade.

Step 5. Click “Update Firmware” or “Update Language” button to start the upgrade.

ADVANCED OPERATION

5. ADVANCED OPERATION

5.1. QUICK SEARCH

You can search any specific events by time and directly play the file you find from the DVR.

Move to “QUICK SEARCH”, and press “ENTER”. You will see the following submenu items:

1) DATE

Select the specific time period (YEAR / MONTH / DAY / HOUR / MIN) that you want to search.

2) SEARCH HDD

Change to the HDD you want if there are more than 1 HDD in your DVR.

3) START

Move to “START” and press “ENTER” button to search and directly playback the recorded files.

5.2. RECORD

In this menu list, you can set record settings. Press “MENU” on the front panel. The default admin password is

0000. Enter the default password, and press “ENTER”.

5.2.1. Quick record setting

Move to “QUICK START” J “RECORD”, and press ”ENTER”. The screen will show the following submenu items:

1) IMAGE SIZE

Select FRAME, FIELD (Selected models only) or CIF.

2) QUALITY

Select one of the four quality options: BEST, HIGH, NORMAL and BASIC.

3) IMAGE PER SECOND

Select the images per second for MANUAL RECORD.

5.2.2. Detailed record setting

Move to “ADVANCE” J “RECORD”, and press ”ENTER”. The screen will show the following submenu items:

1) MANUAL RECORD ENABLE

Start / stop the manual recording function.

2) EVENT RECORD ENABLE

Start / stop the event recording function. When this function is enabled, the recording will be triggered by any

motion or external alarm.

3) TIMER RECORD ENABLE

Start / stop the timer recording that is activated according to the scheduled time

4) EVENT RECORD IPS

Select the images per second for EVENT RECORD (Recording that is triggered by alarm or motion).

5) TIMER RECORD IPS

Select the images per second for TIMER RECORD (Recording that is activated according to the scheduled time.).

ADVANCED OPERATION

6) PRE-ALARM RECORD

Select to enable or disable the pre-alarm function (ON / OFF).

When pre-alarm and event recording functions are both activated, the DVR will record 8MB data before an alarm /

motion event is triggered.

7) OVERWRITE

Select to overwrite previous recorded data in your HDD. When the HDD is full under the O/W recording mode, the

DVR will clear 8GB data from the oldest for continuous recording without notice.

5.3. TIMER

In this menu list, you can schedule different sets of time for recording and detection function. Move to “TIMER”,

and press ”ENTER”. Select to enable (ON) or disable (OFF) the recorder timer and / or detection timer functions.

1) RECORD TIMER

Use S or T to change the setting (ON / OFF). When it’s set to “ON”, press “ENTER” to go to its submenu for

further settings.

RECORD TIMER

0 2 4 6 8 10 12 14 16 18 20 22 24

SUN

MON

TUE

WED

THU

FRI

SAT

PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTINGS uv s t MOVE  SELECT

X axis 0 ~ 24 hours. Each time interval within a square is two hours (divided into four 30-minutes).

Y axis Monday ~ Sunday.

Operation Move to the start time point, and press enter to set the start time point (marked in red color). Then,

press S / T / W / X to set the timer-recording schedule. After setup, press “ENTER” again to create

an ending time point (marked in yellow color) and press “MENU” to exit.

ADVANCED OPERATION

2) DETECTION TIMER

Use S or T to change the setting (ON / OFF). When it’s set to “ON”, press “ENTER” to go to its submenu for

further settings.

DETECTION TIMER

0 2 4 6 8 10 12 14 16 18 20 22 24

SUN

MON

TUE

WED

THU

FRI

SAT

PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTINGS uv s t MOVE  SELECT

X axis 0 ~ 24 hours. Each time interval within a square is two hours (divided into four 30-minutes).

Y axis Monday ~ Sunday.

Operation Move to the start time point, and press enter to set the start time point (marked in red color). Then,

press S / T / W / X to set the timer-recording schedule. After setup, press “ENTER” again to create

an ending time point (marked in yellow color) and press “MENU” to exit.

Note: This function here is only for detection timer setup and activation.

5.4. DETECTION

In this submenu, you can set up detection-related functions.

Move to “DETECTION”, and press ”ENTER”. The screen will show the following submenu items:

There are two different ways to set the detection area depending on the model you have.

5.4.1 For Model 1 & 3

DETECTION

(Take Model 3 as an example) TITLE DET AREA TS ALARM CH1 ON SETUP HIGH OFF CH2 ON SETUP HIGH OFF CH3 ON SETUP HIGH OFF CH4 ON SETUP HIGH OFF CH5 ON SETUP HIGH OFF CH6 ON SETUP HIGH OFF CH7 ON SETUP HIGH OFF CH8 ON SETUP HIGH OFF

PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING uv SELECT s BACK t NEXT  ENTER

1) TITLE

Show the camera title of each channel set in “CAMERA”.

2) DET

Select if you want to activate the motion detection function for the selected channel (ON/OFF).

ADVANCED OPERATION

3) AREA

Press “ENTER” to set the detection area. You will see similar screens as the following:

Transparent blocks are the area under

detection.

Press “ENTER” to confirm the start area. Press W / X to choose the width of the

detection area.

Press S / T to choose the height of the

area.

You can also set up multi-detection area. When any movement is detected, you will

see the grids are flashing.

*Pink blocks represent the area that is not being detected while the transparent blocks are the area under detection.

4) TS (Time of Sensitivity)

“TS” is to set the sensitivity regarding how long one object stays in the detection area and triggers the recording.

There are three level of sensitivity for motion detection. (HIGH / NORMAL / LOW)

5) ALARM

Select N.C. (Normally Closed) / N.O. (Normally open) / OFF for the alarm polarity. The default alarm value is OFF.

5.4.2 For Model 2 & 4

DETECTION

(Take Model 4 as an example) TITLE DET AREA CH1 HIGH SETUP CH2 OFF SETUP CH3 OFF SETUP CH4 OFF SETUP CH5 OFF SETUP CH6 OFF SETUP CH7 OFF SETUP CH8 OFF SETUP

PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING uv SELECT s BACK t NEXT  ENTER

1) TITLE

Show the camera title of each channel set in “CAMERA”.

2) DET

Select HIGH / NORMAL / LOW to activate the motion detection function with different sensitivity for the selected

channel, or select OFF to disable this function.

3) AREA

Press “ENTER” to set the detection area. You will see similar screens as the following:

ADVANCED OPERATION

*Pink blocks represent the area that is not being detected while the transparent blocks are the area under detection.

There are three detection areas for your choice:

Press “▲” or ” ◄” once to broaden the detection area.

Press “▼” or ” ►” once to narrow the detection area.

5.5. REMOTE

In this menu list, you can set up remote devices to work properly.

Move to “REMOTE”, and press ”ENTER”. You will see the following submenu items:

1) TITLE

Show the camera title of each channel set in “CAMERA”.

2) DEVICE

Select the device type (CAMERA / PTZ) according to the connected camera for each channel.

3) ID

Set the ID number (0 ~ 255) for a PTZ camera. After connecting to a PTZ camera correctly, the default ID of the

PTZ camera will be shown on the screen.

4) PROTOCOL

Select NORMAL (our protocol), P-D (PELCO-D) or P-P (PELCO-P) protocol.

5) RATE

Set the baud rate of each channel (2400 / 4800 / 9600 / 19200 / 57600 / 115200). For the connected cameras,

such as PTZ and speed dome cameras, etc., please make sure their baud rate setting is the same as the setting

here.

5.6. SYSTEM INFO

In this menu list, you can check or change some system settings.

The submenu items are described below:

1) SERIAL TYPE

Display the serial type of the DVR (RS485).

2) BAUD RATE

Set the baud rate of the DVR (2400 / 9600 / 19200 / 38400 / 57600 / 115200).

3) HOST ID

Set the ID of the DVR (0 ~ 254).

4) PASSWORD

Press “ENTER” to reset the password for accessing the DVR system. You can set the password up to 4 digits.

Note: Users who use guest password to access the DVR will be only allowed to view the live streaming

video and sequence display, shift the channel display, and lock keys.

ADVANCED OPERATION

5) RESET DEFAULT

Press “ENTER” to reset all settings as default, and select “YES” to confirm or “NO” to cancel.

6) CLEAR HDD

Select the HDD you want to clear. Press “ENTER”, and select “YES” to confirm to clear HDD or “NO” to cancel.

7) UPGRADE

Before using the USB flash drive, please use your PC to format the USB flash drive as FAT32 format first. Then,

save the upgrade file in a compatible USB flash drive, and insert it into the USB port at the front panel. Press

“ENTER”, and select “YES” to confirm upgrade or “NO” to cancel.

Note: To use this function, you need to have the upgrade file saved in a compatible USB flash drive, and

insert it into the USB port at the front or rear panel.

Note: Do not disconnect the power of your DVR while the upgrade process is in progress, or the DVR

functions may not work normally or be unable to use.

8) R.E.T.R. (MIN) (Selected models only)

Select the timeout after which the R.E.T.R. function will be activated (03 / 05 / 10 / 30).

‧ R.E.T.R. On

Press the R.E.T.R. key on the IR remote controller to enable the timeout function. Key in the password, and the

R.E.T.R. delay icon “ ” (in green background) will be shown on the screen. When the RETR function is activated,

the R.E.T.R. on icon “ ” (in red background) will be shown on the screen.

‧ R.E.T.R. Off

Press any key (except “POWER”) and enter the password to turn off the RETR function.

9) AUTO KEYLOCK (SEC)

Set the time-out in second after which the key lock function is activated (NEVER / 30 / 60 / 120).

10) LANGUAGE (Support multi-language)

Select the language of the OSD.

11) VIDEO FORMAT

Here shows the information of the DVR video format (NTSC / PAL).

12) VERSION

Here shows the firmware version information.

5.7. NETWORK

In this menu list, you can set up the network.

Move to “NETWORK”, and press “ENTER” to enter the submenu. The submenu items are described below.

5.7.1. STATIC

1) NETWORK TYPE

Select the network type as STATIC and set all the information needed in the DVR.

2) NETWORK INFORMATION (IP / GATEWAY / NETMASK)

Key in all the network information obtained from your ISP (Internet Service Provider).

3) DNS (PRIMARY DNS / SECONDARY DNS)

Key in the IP address of the domain name server obtained from your ISP (Internet Service Provider).

ADVANCED OPERATION

4) PORT

The valid number ranges from 1 to 9999. The default value is 80. Typically, the TCP port used by HTTP is 80.

However in some cases, it is better to change this port number for added flexibility or security.

See the example below:

STATIC

NETWORK TYPE STATIC

IP 192 . 168 . 001 . 012

GATEWAY 192 . 168 . 001 . 254

NETMASK 255 . 255 . 252 . 000

PRIMARY DNS 168 . 095 . 001 . 001

SECONDARY DNS 139 . 175 . 055 . 244

PORT 0080

PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING uv SELECT s BACK t NEXT  ENTER

5.7.2. PPPOE

5) NETWORK TYPE

Select the network type as PPPOE.

6) USER NAME / PASSWORD

Set the “username” and “password” subscribed from your ISP supplier

7) DNS (PRIMARY DNS / SECONDARY DNS)

Key in the IP address of the domain name server obtained from your ISP (Internet Service Provider).

8) PORT

The valid number ranges from 1 to 9999. The default value is 80. Typically, the TCP port used by HTTP is 80.

However in some cases, it is better to change this port number for added flexibility or security.

See the example below:

PPPOE

NETWORK TYPE PPPOE

USER NAME EMPTY

PASSWORD EMPTY

IP 000 . 000 . 000 . 000

GATEWAY 000 . 000 . 000 . 000

NETMASK 000 . 000 . 000 . 000

PRIMARY DNS 168 . 095 . 001 . 001

SECONDARY DNS 139 . 175 . 055 . 244

PORT 0080

PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING uv SELECT s BACK t NEXT  ENTER

Note: The PPPOE function needs to have one “username” and one “password” subscribed from one ISP

supplier, and a “DDNS account” to correspond the dynamic IP address to a specific “Hostname”.

ADVANCED OPERATION

5.7.3. DHCP

9) NETWORK TYPE

Select the network type as DHCP.

10) DNS (PRIMARY DNS / SECONDARY DNS)

Key in the IP address of the domain name server obtained from your ISP (Internet Service Provider).

11) PORT

The valid number ranges from 1 to 9999. The default value is 80. Typically, the TCP port used by HTTP is 80.

However in some cases, it is better to change this port number for added flexibility or security.

See the example below:

DHCP

NETWORK TYPE DHCP

IP 000 . 000 . 000 . 000

GATEWAY 000 . 000 . 000 . 000

NETMASK 000 . 000 . 000 . 000

PRIMARY DNS 168 . 095 . 001 . 001

SECONDARY DNS 139 . 175 . 055 . 244

PORT 0080

PLEASE CONSULT YOUR INSTALLER FOR ADVANCE SETTING uv SELECT s BACK t NEXT  ENTER

Note: This DHCP function needs to be supported by a router or a cable modem network with DHCP

services, and a “DDNS account” to correspond the dynamic IP address to a specific “Hostname”, for this function to work properly.

5.8. BACKUP

In this menu list, you can choose to make a copy for a specified period time with a compatible USB flash drive,

built-in DVD writer, or USB DVD writer for your own purpose.

Note: For details about the backup devices supported by your DVR, please refer to “APPENDIX 7

SPECIFICATIONS” at page 38.

Note: Before making a video backup with audio, you need to make sure whether there’s any audio camera

connected to the channel which supports audio recording, and there’s any recorded data for the channel.

5.8.1. USB BACKUP

Before making USB backup, please check if:

a). The USB flash drive is supported by your DVR. If not, the message “USB ERROR” will be shown on the

screen.

For the list of the compatible USB flash drives, please refer to “APPENDIX 3 COMPATIBLE USB FLASH

DRIVE LIST” at page 34.

b). The format of your USB flash drive is "FAT 32". If no, please format it to “FAT 32” in your PC.

c). There is no data in the USB flash drive. If yes, it’s recommended to clear all data in the USB flash drive before

starting the backup.

ADVANCED OPERATION

Note: When USB backup starts, it’s not allowed for OSD menu operation or network backup in order to

keep the consistency of the video data.

Note: You can backup up to 2GB video data for one-time USB backup. To backup more data, please set

the time & channel(s) you want, and start USB backup again.

Move to “BACKUP”, and press ”ENTER”. You will see the following submenu items:

1) START TIME

Select the start time of the backup.

2) END TIME

Select the end time of the backup.

3) AVAILABLE SIZE

Display the available capacity in the inserted USB flash drive.

4) CHANNEL

Select channels by pressing “ENTER” button to change the symbol in front of the channel number.

Symbol “ ” means that this channel is selected to backup. Symbol “ □ ” means that this channel is not selected to backup.

5) HDD NUM

Select the HDD containing the data you need.

6) START

Press “ENTER” to start copying the chosen data to the USB flash drive.

Note: Depending on the model you have, this DVR series supports UP TO FOUR audio-in channels,

which are Audio 1, Audio 2, Audio 3 and Audio 4 accordingly, and the audio data will be recorded with the video data of CH1, CH2, CH3 and CH4 respectively. For example, if your DVR supports two audio-in, its audio channels will be Audio 1 and Audio 2. When you playback CH1, you will also hear the audio recording of Audio 1.

5.8.2. DISK BACKUP (Selected models only)

DISK BACKUP is only available for the models with a DVD writer built-in, or the models supporting a USB DVD

writer.

Note: The USB DVD writer is not supplied within the sales package, and needs to be purchased

separately. For the compatible USB DVD writer list, please refer to “APPENDIX 5 COMPATIBLE USB DVD WRITER LIST” at page 36.

FOR USB DVD WRITER

Before making disk backup by a USB DVD writer, make sure:

 Your DVR supports USB DVD writer connection, and the DVR firmware is as follows:

(1) For 16CH models: 1055-1015-1010-1023-1007 or later

(2) For 8CH models: 1030-1015-1010-1023-1007 or later

 Your DVD writer is supported by the DVR. Please check the compatible USB DVD writer list at page 36.

When the above criteria are met, follow the steps below to connect the USB DVD writer to your DVR:

STEP1: Turn on your DVR, and wait till the system initialization is completed.

Note: If your DVR is powered up, please skip to STEP2.

ADVANCED OPERATION

STEP2: Find the data bus & power cables supplied with the USB DVD writer, and connect them to DVD writer as

described in its user manual. Then, plug it into an outlet for power supply.

STEP3: Connect the DVD writer to the USB port of the DVR.

STEP4: Wait till the DVR shows the message “USB CONNECTED”. If this message is not shown, it means the

DVD writer is not detected by the DVR, and you’re unable to use the function “DISK BACKUP”.

STEP5: Press “MENU”, and go to “ADVANCE” J “BACKUP”. Check if the option “DISK BACKUP” is shown.

Note: The option “DISK BACKUP” is shown only when the USB DVD writer is detected by the DVR

correctly.

DISK BACKUP PROCESS

The process below describes how to make a disk backup:

a) Press “EJECT” to open the disk tray. Put a CD or DVD into the DVD writer, and press “EJECT” again to close

the disk tray.

Note: Che ck i f th e ty pe o f yo ur C D or DVD is C D-R or D VD- R. T he m axi mum num ber of b ack up fi les in t he

CD or DVD is 41.

b) Press “MENU”, and go to “ADVANCE” J “BACKUP”. Select “DISK BACKUP”, and you will see the submenu

items almost the same as USB BACKUP.

For the description of the submenu items, please refer to “5.8.1. USB BACKUP”.

c) Set the start time, end time, channels and HDD.

d) Move to “START”, and press “ENTER” to start backup.

While disk backup is processing, users will see the backup completed percentage on the screen.

Note: During the backup process, a file player will also be copied into your disk, and you will see a

message “BACKUP PLAYER” shown on the screen.

e) After disk backup is completed, “BACKUP SUCCESS” will be prompted on the screen. Press “EJECT” to

eject the disk tray and get your disk.

f) Put the CD or DVD into the DVD-ROM drive of your PC. Install the file player “PLAYER.EXE”, and double

click any backup file to play it directly in your PC and see if the backup is successful.

Note: The supported PC operation systems are Windows Vista, XP & 2000.

REMOTE OPERATION

6. REMOTE OPERATION

You can also control the DVR remotely via the supplied licensed software “Video Viewer” (hereafter called the

“Video Viewer”), IE web browser, and Apple’s QuickTime player ONLY when your DVR supports the network

function.

Note: The buttons and functions described below may differ from the actual ones and are for selected

model(s) only.

6.1. Video Viewer

6.1.1. Installation & Network Connection

1) Install the software

Step1: Place the supplied CD into your CD-ROM or DVD-ROM drive. The program will be automatically run.

Step2: Click “Licensed Software AP” to install Video Viewer, or click “Download Latest Version” under “Licensed

Software AP” to download the latest version of Video Viewer from the Internet.

Step3: Follow the on-screen instructions to finish the installation. When the installation is completed, a shortcut

icon “ ” will be placed on your PC desktop.

2) Network Connection

 Local Connection (via LAN)

a) Connect the DVR to your PC via a RJ-45 network cable. The default DVR IP address is “192.168.1.10”, and

the default user name and password are both “admin”.

b) Set the PC’s IP address as “192.168.1.XXX” (1~255, except 10) in order to make the PC and DVR under the

same domain.

c) Double-click “ ” icon on your PC desktop to enter the control panel. By defaults, the “Address Book” ( )

panel will be displayed on the right side of the control panel.

d) Click “ ” (Address Book)  “ ” (Add) button to key in the default IP address, user name,

password, and port number of the DVR you intend to connect.

Click “ ” (Search)  “ ” (Refresh) to search the available IP address(es) of other DVR(s) under the same domain as your PC’s IP address. The found address(es) will be listed, and can be added

into the address book by clicking “ ” (Add into address book).

e) Double-click the IP address you just added into the address book to log in.

 Remote Connection (via Internet)

REMOTE OPERATION

a) Double-click “ ” icon on your PC desktop to enter the control panel. By defaults, the “Address Book” panel

will be displayed on the right side of the control panel.

b) Click ”

” (Address Book)  ” ” (Add) button to key in the IP address, user name, password,

and port number of the DVR you intend to connect.

The default DVR values are as follows:

Item Default Value

IP address 192.168.1.10

User name admin

Password admin

Port 80

Click ” ” (Search)  ” ” (Refresh) to search the available IP address(es) of other DVR(s) under the same domain as your PC’s IP address. The found address(es) will be listed, and can be added

into the address book by clicking ” ” (Add into address book).

c) Double-click the IP address you just added into the address book to log in.

6.1.2. Control Panel

After setting up the network information, login user name and password, double-click “ ” on the PC desktop to

open and log into the control panel. You will see a screen similar to the following with 7 major sections:

NO. Button Function Description

N/A

Image Display The place where the images are displayed.

Address Book

Click to show the predefined IP address(es). You can add, remove or search the IP address to log in the DVR remotely.

Two sub-functions are available for this button: Address Book and Search.

Miscellaneous Control

Click to show the main operation functions: Audio volume control, color setting, backup, record setting, DVR setting, upgrade, and find event logs.

REMOTE OPERATION

NO. Button Function Description

For details, please see “Miscellaneous Control” at page 25.

Record / Record Stop Click to start / stop the manual recording.

Snapshot

Click to take a snapshot of the current view. The snapshot will be saved in the path you specified in “Record Setting”.

Information Click to show the current network connection details.

DVR Control

Click to go to the DVR control panel to operate the DVR remotely.

Miscellaneous Control

Click “ ” (Miscellaneous Control) on the control panel, and six functions are available as follows:

Button Function Description

Color Setting

Click this button to adjust the brightness / contrast / hue / saturation for a single channel or the whole channels.

Backup

To make a video backup remotely, click this button, and you will go to the download setting page.

Record Setting Click to go to the detailed record setting.

Server Setting Click to go into the detailed DVR setting.

Tools

Click to update the firmware version, multilingual OSD and boot display of your DVR remotely.

Status List

Click to view all event and recording logs, search the desired log(s) by date, or playback the recording of the selected log.

6.1.3. General Operation

Record

To record remotely at the same time when any event alarm is triggered at the DVR side, click “ ”

(Miscellaneous Control) → “ ” (Record Setting) to go to the “Record Setting” page.

In the “Record Setting” page, you can set the following items:

‧Record type

REMOTE OPERATION

‧Hard disk overwriting ‧Pre- / post-alarm record time ‧Record time setting ‧Record path

If “Manual” is checked, click “

” (Record) on the main control panel to start the manual recording immediately,

and the recordings will be saved in the specified location. The red text indication “REC” will be shown at the top left

corner of the image display view.

If “Motion” and / or “Alarm” are checked, the recording function will also be enabled at the remote side when any

event is triggered at the DVR side, and the recordings will be saved in the specified location.

Playback

To play a recording, click “ ” (Miscellaneous Control) → “ ” (Status List), and select the “Record” tab or

“Backup” tab. A list of all the recordings will be shown by defaults, and you can also sort out the logs you want to

speed up the search time.

To immediately play a recording, select a log from the list, and click “Play”, or double-click the selected log. A

channel selection window will pop up, and you can select the channel you want to see from the drop-down list.

Then, click “Play”, and the playback control panel will be shown at the bottom of the main control panel similar to

the following.

REMOTE OPERATION

Network Backup

Click “ ” (Miscellaneous Control) → “ ” (Backup) to go into the “Backup” page as follows, and you can

select a specific time range or event to make a video backup remotely.

Note: Before enabling the network backup function, make sure the DVR is not in the playback mode, or

the DVR will stop playback.

Function Description

IP Address / Port / User Name / Password Check if the network connection information of the DVR within which

contains the video data you need is correct.

HDD Number / Channel Specify the hard disk (HDD Number) and channel number (Channel)

within which have the video data you need.

Download by Time Specify the time range within which has the video data you want in the

“Start Time” and “End Time” columns.

Download by Event Select an event log from the event list. This list shows all logs in the

specified DVR from the latest to the earliest.

‧To quickly find the events you need, check or uncheck the event type

“System” / “Manual” / “Alarm” / “Motion”, and select the log you want.

‧To view the earlier or later logs that are not shown in the current

page, click “Prev. Page” or “Next Page”.

‧To refresh the event list, click “Reload”.

File Path Assign the location where the backup files are saved.

Simultaneous Playback To view the backup images simultaneously when the download

process is in progress, select the checkbox “Simultaneous Playback”. You will see the backup images while the images are being downloaded to the PC or notebook.

To simply backup images without previewing, deselect the checkbox “Simultaneous Playback”. You will only see a message box indicating the total time needed, the current status and the saving location.

Download / Cancel Click “Download” to start or “Cancel” to discard the video backup.

REMOTE OPERATION

6.2. IE Web Browser

Note: The supported PC operation systems are Windows Vista / XP / 2000.

Step 4: Key in the IP address used by your DVR in the URL address box, such as 60.121.46.236, and press

Enter. You will be prompted to enter the user name and password to access the DVR.

If the port number your DVR used is NOT 80, you need to key in the port number additionally. The format

is ipaddress:portnum. For example, for IP address 60.121.46.236 and port No. 888, please key

in ”http://60.121.46.236:888” into the URL address box, and press “Enter”.

Step 5: Enter the user name and password, the same as the ones used for video viewer login, and press “OK”.

You will see a screen when the login information is correct.

Note: The buttons and functions described below may differ from the actual ones and are for selected

model(s) only.

Function Description

Home

Click

to go to the main page of the DVR

Config.

Click

to go to the detailed DVR setting.

PTZ

Click

to enter the PTZ mode.

Single Channel

Selection

Click the channel No. to see the live view of the selected channel.

You can also press

or to go to the previous / next channel of the selected channel.

Display Mode

Click the display mode you want to see. There are 3 modes for your choice:

Click

/ / to show 4-cut / 9-cut / 16-cut display.

Snapshot

Click

to take a snapshot for the current view, and open another browser window to display the captured

image.

Selection

Click

or to go to the previous / next channel, or change setting.

REMOTE OPERATION

Function Description

Quad Sequence /

Full Sequence

Quad Sequence

Click to display all the channel images with four channels as a group in a sequence. To exit from this display mode, press any other channel display button.

Full Sequence

Click to display each channel one by one, starting from CH1. When the last channel is displayed, it will start from CH1 again.

To exit from this display mode, press any other channel display button.

Web

Transmission

MPEG4 / QuickTime

QuickTime is Apple Inc.’s multimedia software. You need to have QuickTime installed in you operation system first. When “QuickTime” is selected, you will be promoted to enter the user name and password to access the server of the DVR.

REMOTE OPERATION

6.3. QuickTime Player

You can also use the QuickTime player to remotely log into the DVR and check the live view only. QuickTime

access is only available when the DVR record mode is set to CIF.

Note: QuickTime is Apple’s multimedia software. You need to have QuickTime installed in you operation

system first, and you can access the DVR to see the live view. If you have installed QuickTime, please skip Step 1.

Note: The latest version of QuickTime is V6.4 at the time this manual goes to press, and the supported

operation systems are Windows Vista / XP / 2000, and Apple Mac.

Step 1: Go to Apple’s official website to download QuickTime. The website address is as follows:

http://www.apple.com/quicktime/win.html

a). Click “FFrreeee DDoowwnnllooaadd” to go into the download page, and select to download the free player.

b). Leave your Email address, and click “FFrreeee DDoowwnnllooaadd NNooww” to download the latest QuickTime player.

c). When the download is completed, execute the “QQuuiicckkTTiimmeeIInnssttaalllleerr..eexxee” file, and follow the on-screen

instructions to finish the installation procedure.

Step 2: Open your QuickTime player. Select “File” → “Open URL in New Player…”, and key in the URL address.

The URL format is “rtsp://ipaddress:portnum/live/mpeg4” (For example,

“rtsp://59.124.231.75/live/mpeg4”).

Click “OK” to continue.

Step 3: A pop-up window will appear and prompt you to enter the authentication information.

Note: If you’re not prompted to enter the authentication information, and the error message 10060

appears, go to “Edit”  “Preferences”  “QuickTime Preferences”, and select “Streaming Transport” front he drop-down list. Select “Use HTTP”, and keep the port ID as 80.

Key in the user name and password for accessing your DVR. The user name and password are the same

as the ones you use to log into Video Viewer. If the information is correct, click “OK” to go on. If not, click

“Cancel” to quit the accessing.

Step 4: When the login is successful, you will see the live view.

APPENDIX 2 TROUBLESHOOTING

APPENDIX 1 PIN CONFIGURATION

‧ For 16CH DVR

Siren

When the DVR is triggered by alarm or motion, the COM connects

with NO and the siren with strobe starts wailing and flashing.

Magnetic Contact

When the magnetic contact is opened, the alarm will be triggered and

the recording is on.

PIN FUNCTION DESCRIPTION

1 GND GROUND

2~9 ALARM INPUT

Connect ALARM INPUT (PIN 2 -- 9) and GND (PIN 1) connector with wires. Once an alarm is

triggered, the DVR will start recording and the buzzer will be on.

PIN 2 is Alarm 1. Once the alarm is triggered, the CH1 of the DVR will start alarm-triggered recording.

PIN 3 is Alarm 3. Once the alarm is triggered, the CH3 of the DVR will start alarm-triggered recording.

PIN 4 is Alarm 5. Once the alarm is triggered, the CH5 of the DVR will start alarm-triggered recording.

PIN 5 is Alarm 7. Once the alarm is triggered, the CH7 of the DVR will start alarm-triggered recording.

PIN 6 is Alarm 9. Once the alarm is triggered, the CH9 of the DVR will start alarm-triggered recording.

PIN 7 is Alarm 11. Once the alarm is triggered, the CH11 of the DVR will start alarm-triggered recording.

PIN 8 is Alarm 13. Once the alarm is triggered, the CH13 of the DVR will start alarm-triggered recording.

PIN 9 is Alarm 15. Once the alarm is triggered, the CH15 of the DVR will start alarm-triggered recording.

10 EXTERNAL INPUT 1

11 EXTERNAL OUTPUT 1

12 RS485-A

13 EXTERNAL ALARM NO

Under the normal operation, COM disconnects with NO. But when any alarm is triggered, COM

connects with NO. Attention: The voltage restriction is under DC24V 1A.

14 EXTERNAL INPUT 0

15~22 ALARM INPUT

Connect ALARM INPUT (PIN 15 – 22) and GND (PIN 1) connector with wires. Once an alarm is

triggered, the DVR will start recording and the buzzer will be on.

PIN 15 is Alarm 2. Once the alarm is triggered, the CH2 of the DVR will start alarm-triggered recording.

PIN 16 is Alarm 4. Once the alarm is triggered, the CH4 of the DVR will start alarm-triggered recording.

PIN 17 is Alarm 6. Once the alarm is triggered, the CH6 of the DVR will start alarm-triggered recording.

PIN 18 is Alarm 8. Once the alarm is triggered, the CH8 of the DVR will start alarm-triggered recording.

PIN 19 is Alarm 10. Once the alarm is triggered, the CH10 of the DVR will start alarm-triggered recording.

PIN 20 is Alarm 12. Once the alarm is triggered, the CH12 of the DVR will start alarm-triggered recording.

PIN 21 is Alarm 14. Once the alarm is triggered, the CH14 of the DVR will start alarm-triggered recording.

PIN 22 is Alarm 16. Once the alarm is triggered, the CH16 of the DVR will start alarm-triggered recording.

23 EXTERNAL INPUT 0

24 RS485-B

25 EXTERNAL ALARM COM

Under the normal operation, COM disconnects with NO. But when any alarm is triggered, COM

connects with NO. Attention: The voltage restriction is under DC24V 1A.

APPENDIX 2 TROUBLESHOOTING

‧ For 8CH DVR

Siren

When the DVR is triggered by alarm or motion, the COM

connects with NO and the siren with strobe starts wailing and

flashing.

Magnetic Contact

When the magnetic contact is opened, the alarm will be

triggered and the recording is on.

PIN FUNCTION DESCRIPTION

1 GND GROUND

2~5 ALARM INPUT

Connect ALARM INPUT (PIN 2 – 5) and GND (PIN 1) connector with wires. Once an alarm is

triggered, the DVR will start recording and the buzzer will be on.

PIN 2 is Alarm 1. Once the alarm is triggered, the CH1 of the DVR will start alarm-triggered recording.

PIN 3 is Alarm 3. Once the alarm is triggered, the CH3 of the DVR will start alarm-triggered recording.

PIN 4 is Alarm 5. Once the alarm is triggered, the CH5 of the DVR will start alarm-triggered recording.

PIN 5 is Alarm 7. Once the alarm is triggered, the CH7 of the DVR will start alarm-triggered recording.

10 EXTERNAL INPUT 1

11 EXTERNAL OUTPUT 1

12 RS485-A

13 EXTERNAL ALARM NO

Under the normal operation, COM disconnects with NO. But when any alarm is triggered, COM

connects with NO. Attention: The voltage restriction is under DC24V 1A.

14 EXTERNAL INPUT 0

15~18 ALARM INPUT

Connect ALARM INPUT (PIN 15 – 18) and GND (PIN 1) connector with wires. Once an alarm is

triggered, the DVR will start recording and the buzzer will be on.

PIN 15 is Alarm 2. Once the alarm is triggered, the CH2 of the DVR will start alarm-triggered recording.

PIN 16 is Alarm 4. Once the alarm is triggered, the CH 4 of the DVR will start alarm-triggered recording.

PIN 17 is Alarm 6. Once the alarm is triggered, the CH6 of the DVR will start alarm-triggered recording.

PIN 18 is Alarm 8. Once the alarm is triggered, the CH8 of the DVR will start alarm-triggered recording.

23 EXTERNAL INPUT 0

24 RS485-B

25 EXTERNAL ALARM COM

Under the normal operation, COM disconnects with NO. But when any alarm is triggered, COM

connects with NO. Attention: The voltage restriction is under DC24V 1A.

APPENDIX 2 TROUBLESHOOTING

Please refer to the table below for easy troubleshooting. The table describes some typical problems and also their

solutions. Please check them before calling your DVR dealer.

‧ FAQ (Frequently ask question)

Questions Solutions

Check power cord connection. No power

Confirm that there is power supplied from the outlet.

DVR is not working when pressing any button You might be under “Key Lock” mode. Press any key and enter the

password to exit this mode.

Replace with another HDD for testing. HDD detection failed

Replace with another HDD cable for testing.

Replace with another USB flash drive for testing. Can’t detect your USB flash drive

Format the USB flash drive as FAT32 format and try again.

Confirm the camera is power supplied.

Check the setting of the camera lens.

Check the monitor’s video cable and connection.

No live video

Check the camera’s video cable and connection.

Check if the HDD is installed and connected properly. No recorded video

Check if “MANUAL RECORD ENABLE” option is set to “ON”, and the record function in the “CAMERA” menu is set to “ON”, too.

Timer recording is not working Check if “TIMER RECORD ENABLE” option is set to “ON”, and the

timer schedule has been arranged.

Check if “EVENT RECORD ENABLE” option is set to “ON”.

Check if the detection function “DET” is set to “ON”.

Motion detection recording is not working

Check if the detection area “AREA” has been set.

Can’t play the recorded data on my DVR There must be at least 8192 images of recorded data for playback to

work properly. If not, your DVR will stop the playback. For example, if the IPS is set to 30, the recording time should be at

least 273 seconds (8192 images / 30 IPS) for the playback to work properly.

Make sure your DVR support the audio function.

Make sure your camera supports the audio function.

Can’t backup the video with audio

Make sure your audio camera is connected to the correct DVR audio input.

Check the DVR firmware version. Can’t view the DVR images over the network

with IE web browser after login

Choose to allow the web browser ActiveX or applet in the pop-out message.

You need to be a supervisor to operate this function.

Check if the network connection information is correct (IP Address / Port / User Name / Password).

Failed to backup the recorded files of the DVR from the remote PC side

Specify the hard disk (HDD Number) and channel number (Channel) within which have the recorded data you need.

Check if the USB flash drive is formatted to FAT32. Failed to upgrade the firmware / OSD file via

USB flash drive

Check if the firmware / OSD files are correct.

Check if your DVR supports the IR remote control.

Check if the batteries are installed.

Can’t use the IR remote control

Aim at the IR receiving zone and try again.

APPENDIX 3 COMPATIBLE USB FLASH DRIVE LIST

Please upgrade the firmware of the DVR to the latest version to ensure the accuracy of the following table. If the USB

flash drive is not supported by the DVR, the “USB ERROR” message will be shown on the screen.

Note: Please use your PC to format the USB flash drive as “FAT32”.

Note: You can backup up to 2GB video data for one-time USB backup. To backup more data, please set

the time & channel(s) you want, and start USB backup again.

MANUFACTURER MODEL CAPACITY

Transcend JFV35 4G

JFV30 8G

Kingston DataTraveler 1G

PQI U172P 4G

Apacer AH320 2GB

AH320A 8GB

AH220 1GB

AH320 4GB

A-data RB-18 1GB

Sandisk Cruzer Micro 2G

Cruzer Micro 4G

Cruzer4-pk 2G

Netac U208 1G

MSI F200 4G

SONY Micro Vault Tiny 2G 2G

Micro Vault Tiny 4G 4G

Micro Vault Tiny 1G

APPENDIX 4 COMPATIBLE SATA HDD LIST

MANUFACTURER MODEL CAPACITY ROTATION

ST3320613AS 320GB 7200 rpm

ST33500320AS 500GB 7200 rpm

ST3750330AS 750GB 7200 rpm

Seagate

ST31000340AS 1000GB 7200 rpm

WD3200AAKS 320GB 7200 rpm

WD5000AACS 500GB 7200 rpm

WD6400AAKS 640GB 7200 rpm

WD7500AAKS 750GB 7200 rpm

STM3500320AS 500GB 7200 rpm Maxtor

STM3750330AS 750GB 7200 rpm

HDT725032VLA360 320GB 7200 rpm HITACHI

HDS721010KLA330 1000GB 7200 rpm

APPENDIX 5 COMPATIBLE USB DVD WRITER LIST

Note: The chipsets listed below are for reference only. To ensure the compatibility, please use the

specified models below.

MANUFACTURER MODEL CHIPSET

BENQ EW200G MediaTek

LiteOn DH-20A4P MediaTek

DRU-V200S NEC SONY

AD-7200A NEC

GH22NP20 Panasonic LG

GH20NS15 Renesas

APPENDIX 6 RS485 PROTOCOL

 Use PC keyboards to simulate DVR keypads.  Data: REMOTE PROTOCOL uses 8 bit data, 1 start bit, 1 stop bit.

FUNCTION CODE ASCII FUNCTION CODE ASCII

KEY_MENU 0x4D M KEY_SET_CHANNEL 0x6e n

KEY_ENTER 0x0D ENTER KEY_DWELL 0x65 e

KEY_PLUS 0x6b k KEY_CH1 0x31 1

KEY_MINUS 0x6d m KEY_CH2 0x32 2

KEY_UP 0x55 U KEY_CH3 0x33 3

KEY_DOWN 0x4E N KEY_CH4 0x34 4

KEY_LEFT 0x4C L KEY_CH5 0x35 5

KEY_RIGHT 0x52 R KEY_CH6 0x36 6

KEY_POWER 0x57 W KEY_CH7 0x37 7

KEY_REC 0x72 r KEY_CH8 0x38 8

KEY_PLAY 0x50 P KEY_CH9 0x39 9

KEY_SLOW 0x53 S KEY_CH10 0x41 A

KEY_ZOOM 0x5A z KEY_CH11 0x42 B

KEY_KEY LOCK 0x4B K KEY_CH12 0x43 C

KEY_AUDIO 0x64 d KEY_CH13 0x44 D

KEY_SEARCH 0x73 S KEY_CH14 0x45 E

KEY_PTZ_MODE 0x70 p KEY_CH15 0x46 F

KEY_PTZ_PRESET 0x71 q KEY_CH16 0x47 G

KEY_PTZ_ZOOM_IN 0x69 i KEY_EJECT_DVD 0x6a j

KEY_PTZ_ZOOM_OUT 0x66 f KEY_IRIS_NEAR 0x67 g

KEY_MODE 0x6f o KEY_IRIS_FAR 0x68 h

KEY_4 CUT 0x61 a KEY_PTZ_LIGHT 0x6c l

KEY_9 CUT 0x62 b KEY_PTZ_WIPER 0x77 w

KEY_16 CUT 0x63 c

APPENDIX 7 SPECIFICATIONS

‧ Model 1 ~ 4

MODEL Model 1 Model 2 Model 3 Model 4

Video System NTSC / PAL (auto detection)

Video Input (composite video signal 1 Vp-p 75Ω BNC)

16 channels 8 channels

Video Output (composite video signal 1 Vp-p 75Ω BNC)

Main monitor output

Audio Input / Output

4 audio inputs, 1 audio

output (Mono)

1 audio input, 1 audio

output (Mono)

4 audio inputs, 1 audio

output (Mono)

1 audio input, 1 audio

output (Mono)

Maximum Recording Rate (Frame)

120 IPS @ 704×480 <NTSC> /

100 IPS @ 704×576 <PAL>

60 IPS @ 704×480 <NTSC> /

50 IPS @ 704×576 <PAL>

Maximum Recording Rate (Field)

240 IPS @ 704×240

<NTSC> /

200 IPS @ 704×288

<PAL>

N/A

120 IPS @ 704×240

<NTSC> /

100 IPS @ 704×288

<PAL>

N/A

Maximum Recording Rate (CIF)

480 IPS @ 352×240 <NTSC> /

400 IPS @ 352×288 <PAL>

240 IPS @ 352×240 <NTSC> /

200 IPS @ 352×288 <PAL>

Adjustable Recording Speed (Frame)

120, 60, 30, 15 IPS <NTSC> /

100, 50, 25, 12 IPS <PAL>

60, 30, 15, 7 IPS <NTSC> /

50, 25, 12, 6 IPS <PAL>

Adjustable Recording Speed (Field)

240, 120, 60, 30 IPS

<NTSC> /

200, 100, 50, 25 IPS

<PAL>

N/A

120, 60, 30, 15 IPS

<NTSC> /

100, 50, 25, 12 IPS

<PAL>

N/A

Adjustable Recording Speed (CIF)

480, 240, 120, 60 IPS <NTSC> /

400, 200, 100, 50 IPS <PAL>

240, 120, 60, 30 IPS <NTSC> /

200, 100, 50, 25 IPS <PAL>

Multilingual OSD YES

Image Quality Setting Best, High, Normal and Basic

Hard Disk Storage Accommodates 2 SATA HDDs ( 1 HDD capacity up to 1TB)

Quick Search Time / Motion / Alarm

search mode

Time / Motion search

mode

Time / Motion / Alarm

search mode

Time / Motion search

mode

SATA Interface Built-in

VGA Interface

Built-in (output resolution

up to 1600 x 1200)

N/A

Built-in (output resolution

up to 1600 x 1200)

N/A

Recording Mode

Manual / Timer / Motion /

Alarm / Remote

Manual / Timer / Motion /

Remote

Manual / Timer / Motion /

Alarm / Remote

Manual / Timer / Motion /

Remote

Refresh Rate 480 IPS for NTSC / 400 IPS for PAL 240 IPS for NTSC / 200 IPS for PAL

Multiplex Operation

Live display / record (16 channels) / playback

(simultaneously up to 4 channels) / backup / network

operations

Live display / record (8 channels) / playback

(simultaneously up to 4 channels) / backup / networ

operations

Remote Independent Operation Fully remote independent operation

R.E.T.R. (Remote Event Trigger Recording)

YES N/A YES N/A

Motion Detection Area

16 × 12 grids per camera

for all channels

3 pre-defined detection

areas selectable

16 × 12 grids per camera

for all channels

3 pre-defined detection

areas selectable

Motion Detection Sensitivity One parameter with three sensitivity levels (High / Normal / Low)

Pre-alarm Recording YES (8 MB)

APPENDIX 7 SPECIFICATIONS

MODEL Model 1 Model 2 Model 3 Model 4

Backup Device 1. USB DVD writer (optional); 2. USB 2.0 flash drive; 3. Network

USB Interface

Front panel * 1 /

Back panel * 1

Front panel * 1

Front panel * 1 /

Back panel * 1

Front panel * 1

Ethernet 10/100 Base-T. Supports remote control and live view via Ethernet

Supports licensed software “Video Viewer” / Internet Explorer & Mozilla Firefox web browsers /

QuickTime (5 users access simultaneously)

Web Interface

*Operating System: Windows Vista / XP / 2000; Apple Mac

Remote Alarm Notification E-mail and FTP server N/A E-mail and FTP server N/A

Network Protocol TCP/IP, PPPOE, DHCP and DDNS

IR Remote Control YES (IR receiver built-in)

PTZ Control YES

Dwell Time (Sequential Channel Switch)

Programmable with adjustable dwell time (3 / 5 / 10 / 15 seconds)

Alarm I/O 16 inputs, 1 output N/A 8 inputs, 1 output N/A

Picture Zoom 2X digital zoom (Live & Playback)

Key Lock (Password Protection) YES

Video Loss Detection YES

Camera Title Supports up to 6 letters

Video Adjustable Hue / Saturation / Contrast / Brightness

Date Display Format YY/MM/DD, DD/MM/YY, MM/DD/YY

Daylight Saving YES

Power Source (±10%) DC 19V

Power Consumption (±10%) ＜64 W

Operating Temperature 10℃ ~ 40℃ (50℉~104℉)

Dimensions (mm)** 430(W) x 65(H) x 338(D)

System Recovery System auto recovery after power failure

Optional Peripherals Keyboard controller

Keyboard controller /

VGA converter

Keyboard controller

Keyboard controller /

VGA converter

* The specifications are subject to change without notice. ** Dimensional Tolerance: ±5mm

APPENDIX 7 SPECIFICATIONS

‧ Model 5 ~ 8

MODEL Model 5 Model 6 Model 7 Model 8

Video System NTSC / PAL (auto detection)

Video Input (composite video signal 1 Vp-p 75Ω BNC)

16 channels 8 channels

Video Output (composite video signal 1 Vp-p 75Ω BNC)

Main monitor output

Audio Input / Output

4 audio inputs, 1 audio

output (Mono)

1 audio input, 1 audio

output (Mono)

4 audio inputs, 1 audio

output (Mono)

1 audio input, 1 audio

output (Mono)

Maximum Recording Rate (Frame)

120 IPS @ 704×480 <NTSC> /

100 IPS @ 704×576 <PAL>

60 IPS @ 704×480 <NTSC> /

50 IPS @ 704×576 <PAL>

Maximum Recording Rate (Field)

240 IPS @ 704×240

<NTSC> /

200 IPS @ 704×288

<PAL>

N/A

240 IPS @ 704×240

<NTSC> /

200 IPS @ 704×288

<PAL>

N/A

Maximum Recording Rate (CIF)

480 IPS @ 352×240 <NTSC> /

400 IPS @ 352×288 <PAL>

240 IPS @ 352×240 <NTSC> /

200 IPS @ 352×288 <PAL>

Adjustable Recording Speed (Frame)

120, 60, 30, 15 IPS <NTSC> /

100, 50, 25, 12 IPS <PAL>

60, 30, 15, 7 IPS <NTSC> /

50, 25, 12, 6 IPS <PAL>

Adjustable Recording Speed (Field)

240, 120, 60, 30 IPS

<NTSC> /

200, 100, 50, 25 IPS

<PAL>

N/A

120, 60, 30, 15 IPS

<NTSC> /

100, 50, 25, 12 IPS

<PAL>

N/A

Adjustable Recording Speed (CIF)

480, 240, 120, 60 IPS <NTSC> /

400, 200, 100, 50 IPS <PAL>

240, 120, 60, 30 IPS <NTSC> /

200, 100, 50, 25 IPS <PAL>

Multilingual OSD YES

Image Quality Setting Best, High, Normal and Basic

Hard Disk Storage Accommodates 2 SATA HDDs ( 1 HDD capacity up to 1TB)

Quick Search Time / Motion / Alarm

search mode

Time / Motion search

mode

Time / Motion / Alarm

search mode

Time / Motion search

mode

SATA Interface Built-in

VGA Interface

Built-in (output resolution

up to 1600 x 1200)

N/A

Built-in (output resolution

up to 1600 x 1200)

N/A

Recording Mode

Manual / Timer / Motion /

Alarm / Remote

Manual / Timer / Motion /

Remote

Manual / Timer / Motion /

Alarm / Remote

Manual / Timer / Motion /

Remote

Refresh Rate 480 IPS for NTSC / 400 IPS for PAL 240 IPS for NTSC / 200 IPS for PAL

Multiplex Operation

Live display / record (16 channels) / playback

(simultaneously up to 4 channels) / backup / network

operations

Live display / record (8 channels) / playback

(simultaneously up to 4 channels) / backup / networ

operations

Remote Independent Operation Fully remote independent operation

R.E.T.R. (Remote Event Trigger Recording)

YES N/A YES N/A

Motion Detection Area

16 × 12 grids per camera

for all channels

3 pre-defined detection

areas selectable

16 × 12 grids per camera

for all channels

3 pre-defined detection

areas selectable

Motion Detection Sensitivity One parameter with three sensitivity levels (High / Normal / Low)

Pre-alarm Recording YES (8 MB)

APPENDIX 7 SPECIFICATIONS

MODEL Model 5 Model 6 Model 7 Model 8

Backup Device

1. DVD writer (optional)

2. USB 2.0 flash drive

3. Network

1. USB DVD writer (optional)

2. USB 2.0 flash drive

3. Network

1. DVD writer (optional)

2. USB 2.0 flash drive

3. Network

1. USB DVD writer (optional)

2. USB 2.0 flash drive

3. Network

USB Interface Front panel * 1

Ethernet 10/100 Base-T. Supports remote control and live view via Ethernet

Supports licensed software “Video Viewer” / Internet Explorer & Mozilla Firefox web browsers /

QuickTime (5 users access simultaneously)

Web Interface

*Operating System: Windows Vista / XP / 2000; Apple Mac

Remote Alarm Notification E-mail and FTP server N/A E-mail and FTP server N/A

Network Protocol TCP/IP, PPPOE, DHCP and DDNS

IR Remote Control YES (IR receiver built-in)

PTZ Control YES

Dwell Time (Sequential Channel Switch)

Programmable with adjustable dwell time (3 / 5 / 10 / 15 seconds)

Alarm I/O 16 inputs, 1 output N/A 8 inputs, 1 output N/A

Picture Zoom 2X digital zoom (Live & Playback)

Key Lock (Password Protection) YES

Video Loss Detection YES

Camera Title Supports up to 6 letters

Video Adjustable Hue / Saturation / Contrast / Brightness

Date Display Format YY/MM/DD, DD/MM/YY, MM/DD/YY

Daylight Saving YES

Power Source (±10%) DC 19V

Power Consumption (±10%) ＜64 W

Operating Temperature 10℃ ~ 40℃ (50℉~104℉)

Dimensions (mm)** 430(W) x 65(H) x 338(D)

System Recovery System auto recovery after power failure

Optional Peripherals Keyboard controller

Keyboard controller /

VGA converter

Keyboard controller

Keyboard controller /

VGA converter

* The specifications are subject to change without notice. ** Dimensional Tolerance: ±5mm

APPENDIX 8 RECORDING TIME TABLE

The testing environment for this recording time table is normal office, and for reference only.

Recording time may vary depending on the following three factors:

‧ Different camera resolution; ‧ Different picture complexity; ‧ Different frequency of the object movement

For 16CH DVR

Record Mode Quality IPS 750GB record time (hour) 750GB record time (day)

FRAME BEST 120 151.33 6.31

60 217.77 9.07

30 393.91 16.41

15 558.04 23.25

HIGH 120 202.92 8.46

60 322.72 13.45

30 496.03 20.67

15 622.92 25.96

NORMAL 120 243.51 10.15

60 382.65 15.94

30 595.24 24.80

15 765.31 31.89

BASIC 120 293.70 12.24

60 469.92 19.58

30 669.64 27.90

15 892.86 37.20

FIELD BEST 240 153.94 6.41

120 267.86 11.16

60 398.60 16.61

30 572.34 23.85

HIGH 240 192.70 8.03

120 314.39 13.10

60 385.25 20.22

30 656.51 27.35

NORMAL 240 200.94 8.37

120 360.02 15.00

60 519.10 21.63

30 720.05 30.00

BASIC 240 261.32 10.89

120 413.36 17.22

60 653.31 27.22

30 892.86 37.20

CIF BEST 480 111.61 4.65

240 191.33 7.97

120 343.41 14.31

60 505.39 21.06

HIGH 480 145.57 6.07

240 199.89 8.33

120 412.09 17.17

60 637.76 26.57

NORMAL 480 169.10 7.05

240 297.62 12.40

120 491.48 20.48

60 744.05 31.00

BASIC 480 221.37 9.22

240 382.65 15.94

120 622.92 25.96

60 892.86 37.20

APPENDIX 8 RECORDING TIME TABLE

For 8CH DVR

Record Mode Quality IPS 750GB record time (hour) 750GB record time (day)

FRAME BEST 60 302.66 12.61

30 435.54 18.15

15 787.82 32.83

7 1116.07 46.50

HIGH 60 405.84 16.91

30 645.44 26.89

15 992.06 41.34

7 1245.85 51.91

NORMAL 60 487.01 20.29

30 765.31 31.89

15 1190.48 49.60

7 1530.61 63.78

BASIC 60 587.41 24.48

30 939.85 39.16

15 1339.29 55.80

7 1785.71 74.40

FIELD BEST 120 307.88 12.83

60 535.71 22.32

30 797.19 33.22

15 1144.69 47.70

HIGH 120 385.41 16.06

60 628.77 26.20

30 970.50 40.44

15 1313.03 54.71

NORMAL 120 401.89 16.75

60 720.05 30.00

30 1038.21 43.26

15 1440.09 60.00

BASIC 120 522.65 21.78

60 826.72 34.45

30 1306.62 54.44

15 1785.71 74.40

CIF BEST 240 223.21 9.30

120 382.65 15.94

60 686.81 28.62

30 1010.78 42.12

HIGH 240 291.15 12.13

120 399.79 16.66

60 824.18 34.34

30 1275.51 53.15

NORMAL 240 338.20 14.09

120 595.24 24.80

60 982.96 40.96

30 1488.10 62.00

BASIC 240 442.74 18.45

120 765.31 31.89

60 1245.85 51.91

30 1785.71 74.40

APPENDIX 9 DVR BATTERY REPLACEMENT

DVR time reset after power failure, for example, caused by a power outage, will cause the disorder of the recorded data,

and users may have problems in searching the event clip they want. To keep the DVR time from resetting, a

non-chargeable lithium battery, CR2032, is installed in the DVR.

However, the DVR time might still get reset when the DVR battery is low or even running out of power. If so, please

replace the DVR battery, CR2032, right away

as instructed below.

 How to replace CR2032

Note: The lithium battery, CR2032, is a non-chargeable battery, and should be purchased separately.

Step1: Stop all DVR recording immediately to prevent the disorder of the recorded data. Then, back up the

recorded data if necessary.

Step2: Power off the DVR, and disconnect the DVR power.

Step3: Remove the DVR cover, and find the battery on the mainboard.

For Model 1 ~ 4

The battery is shown and can be easily found when the DVR cover is removed.

For Model 5 ~ 8

The battery is hidden under the 1st bracket as indicated below. Remove the bracket and the battery is shown.

Step4: Push the release as indicated below to remove the battery.

Step5: Get a new battery with the side of “CR2032” facing up, and install it to the mainboard.

Step6: Replace the DVR bracket for Model 5 ~ 8, and replace the DVR cover.

Step7: Connect to DVR power, and turn on the DVR.

Step8: Set DVR date & time, and resume recording. For details, please refer to “3.5. Date and Time Setting” at page

7, and “5.2. RECORD” at page 13.

325Z

中文_KD678_677_676_675_AC758D_757_756D_755_CD536_538_manual_V1.0

數位錄放影機

使用說明書

在使用本機前請務必詳細閱讀安全須知及操作說明，並保存此手冊以備後續參考。

安全須知

圖示說明

此符號用於警告使用者產品機殼內部有 “危險電壓”，觸碰有可能會造成觸電的可能性。.

此符號用於告知使用者此機器附有操作與維護指示的重要文件。

本公提供的所有無鉛產品皆符合歐盟有害物質使用限制指引 (Restriction of Hazardous Substances, (RoHS))，意即本公司的生產流

程與產品均嚴格遵守無鉛守則，而且不包含該指引內提供的任何有害物質。

此劃叉的滾輪垃圾筒圖示代表在歐盟境內，本產品於丟棄時必須另行收集。此原則適用於您的產品與任何標有此圖示的週邊設備。

請勿隨意丟棄這些產品。請洽詢您當地的經銷商，以得知回收此設備的程序。

此機器的製造符合無線電波干擾的規範。

免責聲明

本公司保留可隨時修改或刪除說明書內容的任何權利。本公司不保證此說明書的內容完全無誤、完整或實用性。產品畫面顯示與操作請以實機為主。此說明書內容更改以實際產品為準，將不另行通知。

在此提及的產品與公司名稱，也許為其各自擁有者的註冊商標或商稱名稱。

MPEG4 Licensing

GPL Licensing

This product contains codes which are developed by Third-Party-Companies and which are subject to the GNU

General Public License (“GPL”) or the GNU Lesser Public License (“LGPL”).

The GPL Code used in this product is released without warranty and is subject to the copyright of the corresponding

author.

Further source codes which are subject to the GPL-licenses are available upon request.

We are pleased to provide our modifications to the Linux Kernel, as well as a few new commands, and some tools to get

you into the code.The codes are provided on the FTP site, and please download them from the following site or you can refer to your distributor:

ftp://ftp.dvrtw.com.tw/GPL/AV071/

Version

韌體版本：1055-1015-1010-1023-1007 (16 路機種) / 1030-1015-1010-1023-1007 (8 路機種) Video Viewer： 0113

注意：

為減低觸電的可能性，請勿讓此機器暴露在雨中或潮濕的環境下。

請務必使用適當的變壓器。

本公司不負責賠償任何因不當使用本產品所引起

的損害。即使本公司已被告知可能的相關風險，使用者仍應自行

承擔不當使用所產生之後果。

注注意

意

RRIISSKK OOFF EELLEECCTTRRIICC SSHHOOCCKK

目錄

1. 注意事項................................................................................................................................................................................................................... 1

2. 前面板與背板............................................................................................................................................................................................................2

2.1. 前面板............................................................................................................................................................................................................2

2.2. 背板................................................................................................................................................................................................................ 3

3. 連接與設定...............................................................................................................................................................................................................5

3.1. 硬碟安裝.........................................................................................................................................................................................................5

3.2. 連接攝影機..................................................................................................................................................................................................... 5

3.3. 連接選購設備 (僅限特定型號) ....................................................................................................................................................................... 5

3.4. 電源設定.........................................................................................................................................................................................................5

3.5. 日期與時間設定..............................................................................................................................................................................................6

3.6. 密碼設定.........................................................................................................................................................................................................6

3.7. 錄影設定.........................................................................................................................................................................................................6

4. 基本操作................................................................................................................................................................................................................... 7

4.1 即時畫面 ..........................................................................................................................................................................................................7

4.2. 錄影................................................................................................................................................................................................................ 7

4.3. 影像回放.........................................................................................................................................................................................................8

透過 DVR........................................................................................................................................................................................................ 8

透過隨附軟體 “Video Viewer” ........................................................................................................................................................................8

4.4. 搜尋................................................................................................................................................................................................................ 9

4.5. 韌體 / OSD 升級 ............................................................................................................................................................................................9

5. 進階操作................................................................................................................................................................................................................. 11

5.1. 快速搜尋....................................................................................................................................................................................................... 11

5.2. 錄影.............................................................................................................................................................................................................. 11

5.2.1. 錄影快速設定..................................................................................................................................................................................... 11

5.2.2. 錄影詳細設定..................................................................................................................................................................................... 11

5.3. 預約錄影.......................................................................................................................................................................................................12

5.4. 位移偵測設定...............................................................................................................................................................................................13

5.4.1 Model 1 & 3 ......................................................................................................................................................................................... 13

5.4.2 Model 2 & 4 ......................................................................................................................................................................................... 14

5.5. 遠端設備.......................................................................................................................................................................................................15

5.6. 系統資訊.......................................................................................................................................................................................................15

5.7. 網路設定.......................................................................................................................................................................................................16

5.7.1. 固定 IP...............................................................................................................................................................................................16

5.8. 資料備份.......................................................................................................................................................................................................18

5.8.1. USB 備份............................................................................................................................................................................................18

5.8.2. 光碟備份 (僅限特定型號) .................................................................................................................................................................. 19

6. 遠端操作................................................................................................................................................................................................................. 20

6.1.1. 軟體安裝 & 網路連線........................................................................................................................................................................20

6.1.2. 控制面板............................................................................................................................................................................................21

6.1.3. 常用功能............................................................................................................................................................................................22

6.2. IE 網路瀏覽器 ...............................................................................................................................................................................................25

6.3. QuickTime 多媒體播放軟體..........................................................................................................................................................................27

附錄 1 PIN 腳解說.......................................................................................................................................................................................................28

附錄 2 疑難排解..........................................................................................................................................................................................................30

附錄 3 相容 USB 隨身碟品牌 .....................................................................................................................................................................................31

附錄 4 相容 SATA 硬碟表...........................................................................................................................................................................................32

附錄 5 相容 USB DVD 燒錄機表 ................................................................................................................................................................................33

附錄 6 RS485 通訊協定 ..............................................................................................................................................................................................34

附錄 7 產品規格..........................................................................................................................................................................................................35

附錄 8 錄影時間表...................................................................................................................................................................................................... 39

注意事項

1. 注意事項

 遠端監控

1). 此 DVR 系列支援遠端獨立操作，在遠端看到的每個頻道影像傳輸都會是獨立的。因此，在進行遠端監控時，若要同時觀看四個頻道以上的影像，影像傳輸可能就會有點延遲。

2). 在進行遠端監控時，只能在 ”DVR 控制” ( ) 介面切換頻道顯示，無法進入 DVR 目錄選單。

3). 按擷取目前畫面時，會為每個頻道儲存一個影像。影像快照會儲存在 “Record Setting” (錄影設定) 下指

定的位置。

4). 您可以選擇回放單一頻道的畫面。

5). 若遠端登入的使用者權限為 “guest”，就不會顯示頻道名稱。

 VGA 輸出解析度支援

有內建 VGA 介面的機種，使用者可以視其螢幕類型選擇適合的解析度。

進入 “進階”  “顯示設定”，然後移到 “VGA 輸出” 選取想要的VGA 解析度。解析度選項共有七種如下：

1). 800 x 600 2). 1024 x 768 (預設值) 3). 1280 x 1024

4). 1440 x 900 5). 1400 x 1050 6). 1680 x 1050

7). 1600 x 1200

註：若要讓 LCD 螢幕擁有最佳影像品質，請確認 (1) 您的螢幕有支援選取的 DVR VGA 輸出解析度，以及 (2) 螢幕

和 DVR 的 VGA 輸出設定是相符的。若螢幕影像位置未置中與比例不對，請進入螢幕本身的目錄做調整。詳情請參閱螢幕的使用說明書。

 電源供應

為確保 DVR 可以持續正確運作，建議可視需要加上 UPS (不斷電系統) 較能保護好您的設備持續運作。(選購)

 硬碟掃描與格式化

初次安裝硬碟並將 DVR 開機時，DVR 會自動偵測硬碟，並視情況格式化硬碟。同時，DVR 也會掃描硬碟確認是否有壞的磁區，在錄影和儲存資料時會跳過那些磁區。1TB 硬碟大約需要八分鐘完成整個流程，實際所需時間須視硬碟大小而定。

重新啟動 DVR 後，DVR 仍會掃描硬碟確認是否有壞的磁區，在錄影和儲存資料時會跳過那些磁區。1TB 硬碟大約需要三分鐘完成整個流程，實際所需時間須視硬碟大小而定。

 USB DVD 燒錄機支援

USB DVD 燒錄機支援僅限特定型號。

如需得知您的 DVR 是否支援 USB DVD 燒錄機，請參閱第 35 頁的 “附錄 7 產品規格”。如需得知相容 USB DVD 燒錄機列表，請參閱第 33 頁的 “附錄 5 相容 USB DVD 燒錄機表”。如需得知使用 USB DVD 燒錄機進行影像備份的方法，請參閱第 19 頁的 “5.8.2. 光碟備份 (僅限特定型號)”。

前面板與背板

2. 前面板與背板

2.1. 前面板

1) LED 顯示燈

POWER

: DVR 已開機。

HDD

: 硬碟正在讀取資料或錄影中。

ALARM

: 已觸發警報 (僅供特定型號)。

TIMER

: 已啟動預約錄影。

PLAY

: DVR 處於回放模式下。

2) MENU (目錄選單)

按此按鍵可進入 / 跳出快速選單。

3) ENTER (輸入)

按下此按鍵確認設定。

4) LIST (事件清單搜尋)

要依事件清單快速搜尋錄影檔案，按此鍵即可顯示所有類型的事件清單。從清單選取想要的項目，然後按 “ENTER” 回放選取檔案。

5) SLOW (慢速回放)

在回放模式中，按此按鍵慢速回放錄影檔案。

6) ZOOM (數位變焦)

按此按鍵將選取頻道的影像數位放大。

16 路：按一下顯示 4 / 9 / 16 個頻道的分割畫面。 8 路：按一下顯示 4 / 9 個頻道的分割畫面。

8) SEQ

按一下逐個切換頻道顯示，再按一次即可退出此顯示模式。

註：進入頻道跳台顯示模式時，會自動跳過影像遺失和隱藏錄影的頻道。

9) POWER 或

按住 “POWER” 鍵直到啟動/關閉 DVR。

註：錄影模式下，在關掉 DVR 之前，請先停止錄影。

註：為確保 DVR 可以持續正確運作，建議可視需要加上 UPS (不斷電系統) 較能保護好您的設備持續運作。(選購)

10) 1~16 / 1~8

按其中一個按鍵來顯示該頻道畫面。

11) PLAY (播放)

按此按鍵可回放錄影影片。

12) S (PAUSE / +)、T (STOP/ -)、W (REW)、X (FF)

按這四個按鍵可上 / 下 / 左 / 右移動游標。在回放模式下，按這四個按鍵來暫停 (S) / 停止 (T) / 快轉 (X) / 倒帶 (W) 回放影片。在設定模式下，按 S 或 T 變更設定。

13) AUDIO (SEQ + )

同時按住 “SEQ” + “ ” 可選擇想要的聲音頻道來聽取現場聲音 (在即時模式下) 或錄音 (在回放模式下)。

前面板與背板

14) PTZ (SLOW + ZOOM)

同時按住 “SLOW” + “ZOOM”，可進入/跳出 PTZ 控制模式。

15) USB 埠

快速備份或升級韌體 / OSD。在使用 USB 隨身碟之前，請先將 USB 隨身碟格式化成 “FAT32”。

16) EJECT (僅限特定型號)

按一下可開啟 / 關閉內建 DVD 燒錄機。

17) “MENU” + “ENTER” (按鍵鎖)

同時按 “MENU” + “ENTER” 可鎖定 DVR 前面板的按鍵。若要解除按鍵鎖定，按 DVR 前面板的任何按鍵後，再輸入 DVR 密碼即可解除。

2.2. 背板

1) INPUT (1 ~ 16CH / 1 ~ 8CH)

INPUT：連接到影像來源，如攝影機。

註：若要同時備份影像與聲音，請先確認 DVR 是否有支援收音功能，以及內建麥克風的攝影機是否有正確插入支援收

音的頻道。

2) MONITOR

連接 CRT 螢幕之用。

3) Audio IN

連接到聲音來源，如支援收音功能的攝影機。

請先確認 DVR 是否有支援收音功能，以及哪幾個頻道有支援收音。

註：依各型號而定，此系列 DVR 最多可有四個頻道支援收音功能，分別為 Audio 1、Audio 2、Audio 3 和 Audio 4，

而且聲音資料會分別與 CH1、CH2、CH3 和 CH4 的影像資料錄在一起。舉例來說，若 DVR 只支援兩個音源輸入孔，其音源頻道即為 Audio 1 和 Audio 2。當您回放 CH1 的資料時，也會同時聽見 Audio 1 的錄音。

4) Audio OUT

連接到麥克風或擴音器。

註：視各型號而定，此 DVR 系列最多支援兩個聲音輸出頻道。

請先確認 DVR 是否有支援收音功能，以及哪幾個頻道有支援音源輸出。

5) USB (僅限特定型號)

快速備份或升級韌體 / OSD。在使用 USB 隨身碟之前，請先將 USB 隨身碟格式化成 “FAT32”。

6) IR

IR 遙控器接收線插孔。IR 遙控器接收線為選購配備。

7) EXTERNAL I/O

插入產品包裝隨附的 25 PIN DSUB 轉接頭，以連接外部設備 (例如警報感應器、PTZ 攝影機等等)。詳細的 I/O 埠的 PIN 解說，請參閱第 28 頁的 “附錄 1 PIN 腳解說”。

8) VGA (僅限特定型號)

直接連接至 LCD 螢幕以輸出影像。

註：若要設定 VGA 解析度，請至 “進階”  “顯示設定”  “VGA 輸出”。

9) LAN

以網路線來連上網際網路。

前面板與背板

10) LINK ACT.

DVR 連線上網時，LED 燈就會亮。

11) DC 19V

連接到電源變壓器 (包裝盒內附)。

連接與設定

3. 連接與設定

3.1. 硬碟安裝

在 DVR 開機之前，請務必先安裝好 SATA 硬碟。以下步驟僅供參考。實際安裝方式可能會因 DVR 機種不同而有所差異。

步驟1：取下 DVR 上蓋螺絲以打開 DVR 上蓋。

註： DVR 上蓋是鐵製的，在取下 DVR 上蓋時請小心不要被其邊緣割傷。

步驟2：取出硬碟支援。步驟3：將相容硬碟 PCB 面朝上，連接到電源接頭和資料排線接頭。

註：請確認硬碟電源線是連接到 DVR 主板上的白色接頭，如下所示。咖啡色接頭是保留給 DVD 燒錄機用的 (Model 5

& 7 適用)。

步驟4：將硬碟 PCB 面朝上鎖入硬碟支架，再將硬碟支架鎖回 DVR 內。步驟5：裝回 DVR 上蓋，然後鎖回在步驟 1 鬆開的所有螺絲。

註：初次安裝硬碟並將 DVR 開機時，DVR 會自動偵測硬碟，並視情況格式化硬碟。同時，DVR 也會掃描硬碟確認是

否有壞的磁區，在錄影和儲存資料時會跳過那些磁區。 1TB 硬碟大約需要八分鐘完成整個流程，實際所需時間須視硬碟大小而定。

3.2. 連接攝影機

攝影機必須已經先安裝好並接好電源。之後，再用同軸電纜或接好 BNC 接頭的 RCA 線，連接攝影機和DVR 的影像插孔。DVR 將會自動偵探連接攝影機的影像系統 (NTSC / PAL)，並自動切換到正確的系統。

1) 連接電源

使用指定的電源供應器連接攝影機。

2) 連接影像線

用同軸電纜或接好 BNC 接頭的 RCA 線，連接攝影機和DVR 的影像插孔。

3) 連接音源線

用同軸電纜或接好 BNC 接頭的 RCA 線，連接攝影機和DVR 的音源插孔。

4) 攝影機設定 (限 PTZ 攝影機)

如需得知如何設定攝影機名稱、ID、通訊協定和鮑率，請參閱第 15 頁的 “5.5. 遠端設備”。

3.3. 連接選購設備 (僅限特定型號)

視各 DVR 型號而定，此系列的 DVR 還支援連接到其他選購設備。相關連接細節請參閱其各自的使用說明書。

3.4. 電源設定

此設備操作必須使用製造者所標示的電源供應器類型。將指定的 AC 電源線接到變壓器，並將電源插頭插入電源插座。電源 LED 顯示燈會亮。

連接與設定

註：為確保 DVR 可以持續正確運作，建議可視需要加上 UPS (不斷電系統) 較能保護好您的設備持續運作。UPS 為選

購配備。

3.5. 日期與時間設定

在操作 DVR 之前，請先設定 DVR 的日期與時間。

按 “MENU” 按鍵並輸入密碼，即可進入快速選單。預設的 admin 密碼為 0000。移到 “日期設定”，就可以在此功能清單中設定日期 / 時間 / 日光節約。

註：請勿在錄影時修改日期和時間；否則，錄影資料會錯亂，而且無法依時間來搜尋想要備份的資料。若修改了日期和

時間，建議先將硬碟資料清除後再重新錄影，以免造成錄影時間錯亂。

註：若為初次使用 DVR，請在設定好日期與時間後，將 DVR 連續上電至少 48 小時。

3.6. 密碼設定

按 “MENU” 按鍵並輸入密碼，即可進入快速選單。移到 “進階”，即可進入進階選單。

在 “進階” 目錄選單中，移到 “系統資訊”。選取 “密碼”，然後按 “ENTER” 按鈕進入子目錄選單即可設定密碼 (四碼)。預設的 admin 密碼為 0000。

3.7. 錄影設定

依據預設，當 DVR 開機並接妥攝影機時，錄影功能就會啟動。

若要變更錄影設定，請按 “MENU” 按鍵並輸入密碼進入快速選單。然後，移到 “進階”  “錄影設定” 即可進入進階設定選單。您可以在此設定錄影的影像大小、影像品質和錄影張數 (IPS)。

詳情請參閱第 11 頁的 “5.2. 錄影”。

基本操作

4. 基本操作

4.1 即時畫面

視各 DVR 機種而定，即時畫面可能會出現以下狀態圖示。

圖示功能圖示功能圖示功能圖示功能

按鍵鎖

按鍵解鎖

第一個聲音頻道的現場聲音

第二個聲音頻道的現場聲音

第三個聲音頻道的現場聲音

第四個聲音頻道的現場聲音

第一個聲音頻道的錄音

第二個聲音頻道的錄音

第三個聲音頻道的錄音

第四個聲音頻道的錄音

未選取任何聲音頻道數位變焦模式

未選取數位變焦模式

硬碟覆寫預約錄影

位移偵測

錄影

警報

R.E.T.R. 啟動

(僅限特定型號)

R.E.T.R. 延遲

(僅限特定型號)

4.2. 錄影

當錄影和警報前錄影的功能啟動且硬碟已滿時，本裝置會自動從最舊的資料開始覆寫 8GB 的錄影資料，讓錄影能持續進行，不另行通知。

1) 持續錄影圖示

依據預設，當 DVR 與攝影機正確的連接，並有安裝硬碟時，就會出現 “ ” (錄影中) 的符號。

2) 事件錄影圖示

當位移偵測 / 警報偵測被觸發時，就會出現 “ ” (位移偵測) 或 “ ” (外接警報) 圖示。

3) 預約錄影圖示

當預約錄影啟動時，”TIMER” LED 指示燈會亮起，並出現 “ ” (預約錄影) 圖示。

基本操作

4.3. 影像回放

透過 DVR

按 DVR 控制面板上的 “PLAY” 後，DVR 就會開始回放最後一筆的錄影資料。

您只能同時看見四個頻道的回放畫面。若要看其他頻道，按一下前面板的即可顯示另外四個頻道畫面。

註：若要能正常回放錄影檔案，請至少必須錄超過 8192 張畫面。如果您尚未錄滿 8192 畫面就進行回放動作，DVR

將會停止回放。例如，如果您將 IPS 設為 30，若要正常回放檔案，則錄影時間至少必須超過 273 秒 (8192 張影像 / 30 IPS)。

1) 快轉 / 倒轉

您可以加快 DVR 快轉與倒轉的速度。在回放模式下：按 “FF“ 按鍵一次，DVR 會以 4 倍的速度回放快轉畫面，按兩次，DVR 會以 8 倍的速度 … 以此類推。按 “REW “ 按鍵一次，DVR 會以 4 倍的速度回放倒轉畫面，按兩次，DVR 會以 8 倍的速度 … 以此類推。

註：在回放影像時，螢幕會顯示錄影的影像大小 (FRAME、FIELD 或 CIF)。

2) 暫停 / 影像格放

按 “PAUSE” 按鍵暫停回放。在暫停回放的模式下：按 “►” 按鍵一次，可以格放前進一張圖框影像。按 “◄” 按鍵一次，可以格放倒退一張圖框影像。

3) 停止

在回放模式下，按 “STOP” 按鍵，DVR 的螢幕會回到即時監控模式。

4) 慢速回放

在回放模式下，按一下 “SLOW” 按鍵可以 1/4X 速度慢速回放錄影影片，按兩下可以 1/8X 速度慢速回放。

5) 聲音回放在回放模式下，按 “SEQ” + “ ” 可選擇想要的聲音頻道來聽取錄音。

第一個聲音頻道的回放聲音

第二個聲音頻道的回放聲音

第三個聲音頻道的回放聲音

第四個聲音頻道的回放聲音

聲音頻道未被選取

註：若要同時備份影像與聲音，請先確認 DVR 是否有支援收音功能，以及內建麥克風的攝影機是否有正確插入支援收

音的頻道。

透過隨附軟體 “Video Viewer”

在 DVR 控制 (DVR Control) 介面

按一下選單列的顯示DVR 控制面板，然後按。之後會跳出頻道選擇視窗，讓您選取想要回放的頻道和時間。

基本操作

接著，按 “Play” 立即開始回放。

4.4. 搜尋

透過 DVR

1) 依清單搜尋

按 “LIST” 顯示所有類型的事件錄影清單。選擇欲觀看的項目，然後按 “ENTER” 按鍵開始回放。

2) 依時間搜尋

按 “MENU” 進入快速選單，然後到 “進階”  “事件記錄”。移至 “快速搜尋”，然後按 “ENTER” 進入快速搜尋選單。您可以依時間搜尋特定事件 (年 / 月 / 日 / 時 / 分) 並直接回放搜尋到的檔案。

透過隨附軟體 “Video Viewer”

透過隨附軟體 “Video Viewer” 搜尋事件

按一下選單列的，然後按進入 “Status List” (狀態清單) 頁面。選擇 “Record” (錄影) 標籤顯示所有錄影記錄，或者依時間或事件來加以分類。

從清單選取想要的記錄，然後按 “Play” (回放)，或者連按兩下選取記錄。之後會跳出頻道選取視窗，請從下拉式清單選取想要回放的頻道。

接著，按 “Play” 立即開始回放。

4.5. 韌體 / OSD 升級

1) 使用 USB 隨身碟進行升級

步驟 1：先將 USB 隨身碟格式化成 FAT32 的格式。步驟 2：從您的經銷商取得升級的檔案，並將升級檔案存放在您的 USB 隨身碟中 (請勿變更檔名)。步驟 3：將 USB 隨身碟插入 USB 埠，待 DVR 偵測您的裝置。步驟 4：移到 “進階”  “系統資訊”，然後移到 “升級”，再按 “ENTER” 確認。步驟 5：選擇 “是”，並再按 “ENTER” 按鍵確認進行升級。

2) 使用隨附軟體 Video Viewer 進行升級

步驟 1：將升級檔案存放至您的電腦 (請勿變更檔名)，然後登入 Video Viewer。

步驟 2：按 “ ” 按鈕顯示其他功能控制面板。在此控制面板中，按 “ ” 進入Video Viewer 升級視窗。

步驟 3：輸入 DVR 的使用者名稱、密碼、IP 位址與埠號。

基本操作

步驟 4：在 “Update Server” (更新伺服器) 下，視要升級的檔案按 “Firmware” (韌體) 或 ”Language” (語言) 標籤，

然後按 “Add” (新增) 選擇所提供的韌體或 OSD 檔案來升級。

步驟 5：按 “升級韌體” 或 “升級語言” 按鈕開始升級。

進階操作

5. 進階操作

5.1. 快速搜尋

您可以依時間搜尋特定事件，並在 DVR 直接播放找到的檔案。移到 “快速搜尋”，然後按 “ENTER”。您將會看到以下功能選項：

1) 日期

選擇想要搜尋的特定時間範圍 (年 / 月 / 日 / 時 / 分)。

2) 搜尋硬碟

若您的 DVR 機種支援容納 1 顆以上的硬碟，請切換到想要搜尋的硬碟。

3) 開始

移到 “開始”，然後按 “ENTER” 鍵開始搜尋與直接回放錄影檔。

5.2. 錄影

在此功能選單下，您可以設定錄影功能。按 “MENU”。預設 admin 密碼為 0000。輸入預設密碼，然後按 “ENTER”。

5.2.1. 錄影快速設定

移到 “快速選單” J “錄影” 圖示，然後按 ”ENTER”。您會看到以下功能選項：

1) 影像大小

選擇 FRAME、FIELD (僅供特定型號) 或CIF。

2) 錄影品質

選擇其中一種錄影影像大小：最好、高、一般和基本。

3) 錄影張數 (IPS)

選擇手動錄影的 IPS (每秒播放圖像的速度)。

5.2.2. 錄影詳細設定

移到 “進階” J “錄影設定”，然後按 ”ENTER”。您會看到以下功能選項：

1) 手動錄影

設定開啟或關閉手動錄影功能 (ON / OFF)。

2) 事件錄影

設定開啟或關閉事件錄影功能 (ON / OFF)。啟動此功能後，發生位移偵測或外部警報時就會觸發錄影。

3) 預約錄影

設定開啟或關閉預約錄影功能 (ON / OFF)。

4) 事件錄影張數 (每秒)

選擇事件錄影 (警報或位移偵測觸發錄影) 的每秒錄影張數。

5) 預約錄影張數 (每秒)

選擇預約錄影 (依照設定排程啟動錄影) 的每秒錄影張數。

進階操作

6) 警報前錄影

設定警報前錄影功能開/關 (ON / OFF)。當事件錄影功能與警報前錄影功能皆為啓動狀態下，若發生警報或位移偵測，DVR 會從觸發前 8MB 的檔案開始錄起。

7) 硬碟覆寫

選擇開啟此功能 (ON) 可覆寫硬碟的錄影檔案。DVR 會在硬碟錄滿時，從最早的錄影資料開始，一次清除8GB 空間的資料(無任何警訊提醒)。

5.3. 預約錄影

在此功能選單下，您可以設定不同的時間組來進行錄影或啟動位移偵測功能。移到 “預約錄影” 圖示，然後按 ”ENTER”。選擇要啟動 (ON) 或關閉 (OFF) 預約錄影和 / 或預約位移偵測錄影功能。

1) 預約錄影

按S 或 T 可變更設定 (ON / OFF)。若此功能設為 “ON” (開)，請按輸入鍵進入子目錄選項來進行進一步的設定。

預約錄影

0 2 4 6 8 10 12 14 16 18 20 22 24

星期日

星期一

星期二

星期三

星期四

星期五

星期六

進階選單設定請聯絡與諮詢您的安裝商

uv s t 移動  選取

X 軸 0 ~ 24 小時。每個時間方塊為 2 小時，再細分為四個小方塊，每個小方塊分別為 30 分鐘。 Y 軸星期一 ~ 星期日。.

操作說明移到要開始的時間點，然後按 ”ENTER” 鍵設定開始時間點 (標示為紅色)。然後，按 S / T / W / X

來設定預約錄影的時間。設定完畢後，再按一下 ”ENTER” 鍵設定結束時間點 (標示為黃色)，然後按 “MENU” 鍵退出。

進階操作

2) 預約偵測錄影

按S 或 T 可變更設定 (ON / OFF)。若此功能設為 “ON” (開)，請按輸入鍵進入子目錄選項來進行進一步的設定。

預約偵測錄影

0 2 4 6 8 10 12 14 16 18 20 22 24

星期日

星期一

星期二

星期三

星期四

星期五

星期六

進階選單設定請聯絡與諮詢您的安裝商

uv s t 移動  選取

X 軸 0 ~ 24 小時。每個時間方塊為 2 小時，再細分為四個小方塊，每個小方塊分別為 30 分鐘。 Y 軸星期一 ~ 星期日。.

操作說明移到要開始的時間點，然後按 ”ENTER” 鍵設定開始時間點 (標示為紅色)。然後，按 S / T / W / X

來設定預約錄影的時間。設定完畢後，再按一下 ”ENTER” 鍵設定結束時間點 (標示為黃色)，然後按 “MENU” 鍵退出。

註：此處僅為設定與啟動預約位移偵測功能。

5.4. 位移偵測設定

在此子目錄選單中，您可以設定與位移偵測相關的功能。移到 “位移偵測設定”，然後按 “ENTER” 鍵確認。您會看到以下功能選項：

依各型號而定，設定位移偵測區域的方式有兩種。

5.4.1 Model 1 & 3

位移偵測設定

(以 Model 3 為例) 名稱偵測移動區域設定 TS 警報 CH1 ON 設定高 OFF CH2 ON 設定高 OFF CH3 ON 設定高 OFF CH4 ON 設定高 OFF CH5 ON 設定高 OFF CH6 ON 設定高 OFF CH7 ON 設定高 OFF CH8 ON 設定高 OFF

進階選單設定請聯絡與諮詢您的安裝商 uv 選取 s上一個 t下一個  進入

1) 名稱

顯示每個頻道的攝影機名稱 (在 “攝影機設定” 目錄選單中設定)。

2) 偵測

選擇是否要啟動選取頻道的位移偵測功能 (ON/OFF)。

進階操作

3) 移動區域設定

按 “ENTER” 設定位移偵測區域。之後會出現類似以下的畫面：

透明方格表示未偵測區域。按 “ENTER” 鍵確認開始位置。按 W / X 鍵選擇偵測區域的寬度。

按 S / T 鍵選擇偵測區域的高度。您也可以設定多個偵測區域。當偵測到任何動作時，您會看見方格在閃動。

*粉紅色格子代表未被偵測的區域，而透明的格子代表有偵測的區域。

4) TS (時間靈敏度)

“TS” 是物體持續觸發位移偵測的時間長短的靈敏度。位移偵測靈敏度有三種等級(高 / 一般 / 低)

5) 警報

以外接警報設備的 Alarm Polarity 為依據，來選擇將此選項設定為 N.C. / N.O.。預設值為 OFF (關)。

5.4.2 Model 2 & 4

位移偵測設定

(以 Model 4 為例)

名稱偵測移動區域設定

CH1 高設定 CH2 OFF 設定 CH3 OFF 設定 CH4 OFF 設定 CH5 OFF 設定 CH6 OFF 設定 CH7 OFF 設定 CH8 OFF 設定

進階選單設定請聯絡與諮詢您的安裝商 uv 選取 s上一個 t下一個  進入

1) 名稱

顯示每個頻道的攝影機名稱 (在 “攝影機設定” 目錄選單中設定)。

2) 偵測

選擇 “高” / “一般” / “低”，或選擇 “OFF” 關閉此功能。

3) 移動區域設定

按 “ENTER” 設定位移偵測區域。之後會出現類似以下的畫面：

*粉紅色格子代表未被偵測的區域，而透明的格子代表有偵測的區域。

進階操作

區域設定共有三種可供選擇：按 “▲” 或 ” ◄” 可擴大偵測區域。按 “▼” 或 ” ►” 可縮小偵測區域。

5.5. 遠端設備

在此功能選單中，您可以進行遠端設備的相關設定。移到 “遠端設備”，然後按 ”ENTER”。您將會看到以下功能選項：

1) 名稱顯示每個頻道的攝影機名稱 (在 “攝影機設定” 目錄選單中設定)。

2) 裝置依據每一頻道所外接的攝影機，來選擇設備類別 (CAMERA / PTZ)。

3) ID 設定連接 PTZ 攝影機的 ID 數值 (0 ~ 255)。正確連接到 PTZ 攝影機後，螢幕將會顯示該攝影機的預設 ID。

4) 通訊協定選擇 NORMAL (本品牌的通訊協定)、P-D (PELCO-D) 或 P-P (PELCO-P) 通訊協定。

5) 鮑率

設定連接的 PTZ 攝影機鮑率 (2400 / 4800 / 9600 / 19200 / 57600 / 115200)。請確認 PTZ 攝影機的鮑率設定，和此處所設定的鮑率是一致的。

5.6. 系統資訊

在此目錄選單中，您可以查閱或變更系統設定。之後會出現以下選項功能：

1) 序列裝置類別

此處顯示 DVR 使用的序列裝置類別 (RS485)。

2) 鮑率

設定 DVR 的鮑率 (2400 / 9600 / 19200 / 38400 / 57600 / 115200)。

3) ID

設定 DVR 的 ID (0 ~ 254)。

4) 密碼

按 “ENTER” 重設存取 DVR 系統的密碼。您可以設定 4 位數的密碼。

註：使用訪客帳號和密碼存取 DVR 的使用者，只能檢視即時影像和跳台顯示、切換頻道顯示，以及鎖定按鍵。

5) 回復預設值

按 “ENTER”，然後選擇 “是”，可確認回復預設值；選擇 “否” 則可取消重設。

6) 清除硬碟

選擇要清除資料的硬碟。按 “ENTER”，並選擇 “是” 確認清除硬碟，或選擇 “否” 取消。

7) 升級

在使用 USB 隨身碟之前，請先使用您的電腦將 USB 隨身碟格式化成FAT32 的格式。將升級檔儲存在相容的 USB 隨身碟內，然後插入前面板的 USB 埠。按 “ENTER”，並選擇 “是” 確認進行升級，或選擇 “否” 取消。

註：在使用升級功能之前，請先將升級檔儲存在相容的 USB 隨身碟內，然後插入前面板或背板的 USB 埠。

註：在升級時請勿關機，否則 DVR 部分功能可能會無法正常執行。

進階操作

8) R.E.T.R. 延遲 (分) (僅限特定型號)

選擇 R.E.T.R. 功能啟動的倒數時間 (03 / 05 / 10 / 30)。

‧ R.E.T.R. (遠端事件觸發錄影) 啟動：

按隨附遙控器上的R.E.T.R. 鍵即可啟動功能倒數功能。輸入密碼後，螢幕上會顯示倒數圖示 “ ” (綠色)。當 R.E.T.R.

功能啟動時，螢幕上會顯示 “

” 圖示 (紅色)。

‧ R.E.T.R. (遠端事件觸發錄影) 關閉：

按任意鍵 (“POWER” 除外)，然後輸入密碼即可關閉此功能。

9) 按鍵鎖 (秒)

設定於停止操作特定時間之後，啟動自動按鍵鎖功能 (停用 / 30 / 60 / 120)。

10) 語言 (多語 OSD)

選擇 OSD 的語言。

11) 視訊系統

在此會顯示 DVR 的視訊系統 (NTSC/ PAL)。

12) 版本

在此會顯示韌體的版本。

5.7. 網路設定

在此功能選單下，您可以進行網路功能的設定。移到 “網路設定”，然後按 “ENTER” 鍵進入子目錄選單。之後會出現以下選項功能。

5.7.1. 固定 IP

1) 網路類型

將網路類型設成固定 IP，然後設定 DVR 需要的所有資訊。

2) 網路資訊 (IP 網址 / 閘道 / 網路遮罩)

輸入您由網路 ISP 業者那得到的所有網路資訊。

3) DNS (主要 DNS / 次要 DNS)

輸入您由網路 ISP 業者那得到的 DNS (網域名稱伺服器) IP 位址。

4) 埠

有效數值範圍為 1 到 9999。預設值為 80。一般而言，HTTP 所使用的 TCP 埠多半為 80 埠。然而有些情形下，建議您最好變更此埠值以增加彈性或安全性。

請見下例：

固定 IP

網路類型

固定 IP IP 網址 192 . 168 . 001 . 012 閘道 192 . 168 . 001 . 254 網路遮罩 255 . 255 . 252 . 000 主要 DNS 168 . 095 . 001 . 001 次要 DNS 139 . 175 . 055 . 244 埠 0080

進階選單設定請聯絡與諮詢您的安裝商 uv 選取 s上一個 t下一個  進入

進階操作

5.7.2. PPPOE

1) 網路類型

將網路類型設為 PPPOE。

2) 使用者名稱 / 密碼

輸入由您的網路 ISP 業者提供的使用者名稱和密碼。

3) DNS (主要 DNS / 次要 DNS)

輸入您由網路 ISP 業者那得到的 DNS (網域名稱伺服器) IP 位址。

4) 埠

有效數值範圍為 1 到 9999。預設值為 80。一般而言，HTTP 所使用的 TCP 埠多半為 80 埠。然而有些情形下，建議您最好變更此埠值以增加彈性或安全性。請見下例：

PPPOE

網路類型 PPPOE 使用者名稱空密碼空 IP 網址 000 . 000 . 000 . 000 閘道 000 . 000 . 000 . 000 網路遮罩 000 . 000 . 000 . 000 主要 DNS 168 . 095 . 001 . 001 次要 DNS 139 . 175 . 055 . 244 埠 0080

進階選單設定請聯絡與諮詢您的安裝商 uv 選取 s上一個 t下一個  進入

註： PPPOE 功能必須要有網路 ISP 業者提供的使用者名稱和密碼，以及可將浮動 IP 位址對應到特定 “主機名稱” 的

“DDNS 帳號”，才可正常使用。

5.7.3. DHCP

1) 網路類型

將網路類型設為 DHCP。

2) DNS (主要 DNS / 次要 DNS)

輸入您由網路 ISP 業者那得到的 DNS (網域名稱伺服器) IP 位址。

3) 埠

有效數值範圍為 1 到 9999。預設值為 80。一般而言，HTTP 所使用的 TCP 埠多半為 80 埠。然而有些情形下，建議您最好變更此埠值以增加彈性或安全性。

請見下例：

DHCP

網路類型 DHCP IP 網址 000 . 000 . 000 . 000

閘道 000 . 000 . 000 . 000 網路遮罩 000 . 000 . 000 . 000 主要 DNS 168 . 095 . 001 . 001 次要 DNS 139 . 175 . 055 . 244 埠 0080

進階選單設定請聯絡與諮詢您的安裝商 uv 選取 s上一個 t下一個  進入

進階操作

註： DHCP 功能必須要有支援 DHCP 服務的路由器或或數據機，以及可將浮動 IP 位址對應到特定 “主機名稱” 的

“DDNS 帳號”，才可正常使用。

5.8. 資料備份

在此功能選單下，您可以使用相容的 USB 隨身碟、內建 DVD 燒錄機或外接USB DVD 燒錄機，來備份指定時間內的影像。

註：如需得知 DVR 支援的備份裝置，請參閱第 35 頁的 “附錄 7 產品規格”。

註：若要同時備份影像與聲音，請先確認內建麥克風的攝影機是否有正確插入支援收音的頻道，以及該頻道是否有錄影資料。

5.8.1. USB 備份

在進行 USB 備份之前，請先確認下列項目：

a). DVR 支援您所使用的 USB 隨身碟。如果 DVR 與您的 USB 隨身碟不相容，您將會看見螢幕上出現 “USB 錯誤”

的訊息。若欲得知相容的 USB 隨身碟品牌，請參閱第 31 頁的 “附錄 3 相容 USB 隨身碟品牌”。

b). 您所使用的 USB 隨身碟格式必須為 "FAT32"。若不是，請在電腦中將 USB 隨身碟格式化成 ”FAT32” 的格式。

c). USB 隨身碟內沒有資料。如果有資料的話，建議您先將 USB 隨身碟內的資料清空，再進行檔案備份。

註：在進行 USB 備份時，請勿執行任何 OSD 操作或網路備份，以確保影像資料的一致性。

註： USB 備份一次最多只能備份 2GB 的影像檔案。若要備份更多錄影資料，請再設定一次時間和想要備份的頻道，然

後再次啟動 USB 備份功能。

移到 “USB 備份”，然後按 “ENTER”。您將會看到以下功能選項：

1) 開始時間

選擇備份的開始時間。

2) 結束時間

選擇備份的結束時間。

3) 剩餘容量

顯示 USB 隨身碟的可用空間容量。

4) 頻道

移動游標到欲備份的頻道，按 “ENTER” 改變頻道數字前方的圖示。

” 圖示表示已選取該頻道進行備份。 “ □ ” 圖示表示未選取該頻道進行備份。

5) 硬碟

選擇備份檔案所存放之 DVR 硬碟。

6) 開始

按 “ENTER”，開始備份檔案到 USB 隨身碟。

註：依各型號而定，此系列 DVR 最多可有四個頻道支援收音功能，分別為 Audio 1、Audio 2、Audio 3 和Audio

4，而且聲音資料會分別與 CH1、CH2、CH3 和 CH4 的影像資料錄在一起。舉例來說，若 DVR 只支援兩個音源輸入孔，其音源頻道即為 Audio 1 和 Audio 2。當您回放 CH1 的資料時，也會同時聽見 Audio 1 的錄音。

進階操作

5.8.2. 光碟備份 (僅限特定型號)

光碟備份功能只限有內建 DVD 燒錄機的機種，或者支援外接 USB DVD 燒錄機的機種才能使用。

註：USB DVD 燒錄機為選購配備。如需得知相容 USB DVD 燒錄機列表，請參閱第 33 頁的 “附錄 5 相容 USB DVD

燒錄機表”。

USB DVD 燒錄機

在使用 USB DVD 燒錄機建立光碟備份之前，請先確認：

 DVR 支援連接 USB DVD 燒錄機，而且 DVR 韌體版本如下：

(1) 16 路機種：1055-1015-1010-1023-1007 或更新版本 (2) 8 路機種：1030-1015-1010-1023-1007 或更新機種

 DVR 支援您的 USB DVD 燒錄機機種。請參閱第 33 頁的相容 USB DVD 燒錄機清單。

以上事項確認無誤後，請按照以下步驟將 USB DVD 燒錄機接到 DVR：

步驟 1：將 DVR 開機，並等到系統初始化完成。

註：若 DVR 已開機，請跳至步驟步驟 2。

步驟 2：找到 USB DVD 燒錄機隨附的資料排線和電源線，然後按照其說明書指示，先連接到燒錄機，再插入電源

插座。

步驟 3：將該燒錄機插入 DVR 的 USB 埠。

步驟 4：等到 DVR 顯示 “USB 裝置連接” 訊息。若沒有顯示此訊息，表示 DVR 偵測不到此燒錄機，也就無法使

用 “光碟備份” 功能。

步驟 5：按 “MENU”，然後移至 “進階” J “資料備份”。確認 “光碟備份” 選項是否有顯示。

註：當 DVR 可正確偵測到連接的 USB DVD 燒錄機時，才會顯示 “光碟備份” 選項。

光碟備份程序

以下程序說明如何進行光碟備份：

a) 按 “EJECT” 退出光碟托盤。將 CD 或 DVD 片放入燒錄機，然後再按一次 “EJECT” 關閉光碟托盤。

註：確認 CD 或 DVD 光碟類型為 CD-R 或 DVD-R。可以備份到 CD 或 DVD 光碟的檔案數量最多為 41 個。

b) 按 “MENU”，然後移到 “進階” J “資料備份”。選擇 “光碟備份” 後，就會看到和 USB 備份功能相似的子目錄

選單。如需得知各子選單的說明，請見 “5.8.1. USB 備份”。

c) 設定開始時間、結束時間、頻道和硬碟編號。

d) 移到 “開始”，然後按 “ENTER” 開始進行備份。

在進行光碟備份時，螢幕會顯示備份完成的比例。

註：在備份期間，會同時複製一個檔案播放軟體到光碟片中，且螢幕會顯示相關訊息。

e) 備份完成後，螢幕會顯示 “備份成功” 訊息。按 “EJECT” 退出光碟托盤取出光碟片。

f) 將 CD 或DVD 光碟片放入電腦光碟機中。選取 “PLAYER.EXE”，然後點兩下執行安裝。安裝完成後，點兩下

備份下來的檔案即可直接在電腦播放。請確認檔案備份是否成功。

註：支援的電腦作業系統為 Windows Vista、XP & 2000。

REMOTE OPERATION

6. 遠端操作

您也可以使用隨附的專利軟體 Video Viewer、Internet Explorer 網路瀏覽器，以及 Apple 的 QuickTime 多媒體播放器來遠端控制 DVR。

註：以下說明的按鍵和功能也許會和實際看到的有所差異，而且僅限特定型號才可使用。

6.1. Video Viewer

6.1.1. 軟體安裝 & 網路連線

1) 安裝軟體

步驟 1：將隨附的 CD-ROM 放到 DVD- / CD-ROM 光碟機中。程式會自動啟動如下。

步驟 2：點一下 “Licensed Software AP” 來安裝 Video Viewer，或點一下 “Licensed Software AP” 下的

“Download Latest Version” 從網路下載新版 Video Viewer 進行安裝。

步驟 3：請遵照螢幕上的指示完成安裝程序。安裝結束後，電腦桌面會出現 “ ” 捷徑圖示。

2) 網路連線

 區域連線 (透過 LAN)

a) 使用一條 RJ-45 網路線連接 DVR 和電腦。預設的 DVR IP 位址為 “192.168.1.10”，而預設的使用者名稱和密

碼皆為 “admin”。

b) 將電腦的 IP 位址設為 “192.168.1.XXX ” (1~255 皆可，除了 10 之外)，讓電腦以及 DVR 位在同一個網域。

c) 連按兩下桌面上的 “ ” 圖示進入 Video Viewer 控制面板。依據預設，Video Viewer 的控制面板右側會顯示

連線位址簿畫面。

d) 按 “ ” (位址簿)  “ ” (新增) 輸入您要連線的 DVR 預設 IP 位址、使用者名稱、密碼和連接埠號。

或者

按 “ ” (搜尋)  “ ” (重新整理) 搜尋與您的電腦 IP 位址位在相同網域下的其他 DVR 的 IP 位

址。之後會列出找到的位址。您可以按 “ ” 將該位址加入連線位址簿。

e) 連按兩下您剛加入連線位址簿的 IP 位址進行登入。

REMOTE OPERATION

 遠端連線 (透過 Internet)

a) 連按兩下桌面上的 “ ” 圖示進入 Video Viewer 控制面板。依據預設，Video Viewer 的控制面板右側會顯示

連線位址簿畫面。

b) 按 “ ” (位址簿)  “ ” (新增) 輸入您要連線的 DVR 預設 IP 位址、使用者名稱、密碼和連接埠號。

DVR 的預設值如下：

項目預設值

IP 位址

192.168.1.10

使用者名稱

admin

密碼

admin

埠號

或者

按 “ ” (搜尋)  “ ” (重新整理) 搜尋與您的電腦 IP 位址位在相同網域下的其他 DVR 的 IP 位

址。之後會列出找到的位址。您可以按 “ ” 將該位址加入連線位址簿。

c) 連按兩下您剛加入連線位址簿的 IP 位址進行登入。

6.1.2. 控制面板

在設完網路資訊、登入使用者名稱和密碼，連按兩下電腦桌面上的 “ ” 來開啟和登入控制面板。您會看見類似以

下畫面，分成七個主要區域：

NO.

按鈕功能說明

N/A

影像顯示顯示影像的區域。

位址簿

按一下可顯示預設的 IP 位址。您可以新增、移除或搜尋要遠端登入的 DVR IP 位址。

此按鈕有兩個子功能可以使用：位址簿和搜尋。

其他控制功能

按一下可顯示主要控制功能：音量控制、顏色設定、備份、錄影設定、伺服器設定、工具和事件清單。

REMOTE OPERATION

NO.

按鈕功能說明

詳情請參閱第 22 頁的 “其他控制功能“。

錄影 / 停止錄影按一下可開始 / 停止手動錄影。

快照

按一下可擷取目前畫面的快照。影像快照會儲存在 “Record Setting” (錄影設定) 下指定的位置。

資訊按一下可顯示目前的網路連線詳細資訊。

DVR 控制按一下可進入 DVR 控制面板來遠端操作 DVR。

其他控制功能

按一下控制面板上的 “ ” (其他控制功能) 會顯示以下六項功能：

按鈕功能說明

顏色設定

按一下可調整單一頻道或全部頻道的亮度 / 對比度 / 色相 / 飽和度。

備份要進行網路備份，請按一下此按鈕進入下載設定頁面。

錄影設定按一下可進入詳細的錄影設定頁面。

伺服器設定按一下可進入詳細的 DVR 設定頁面。

工具按一下可遠端更新 DVR 的韌體、多語 OSD 和開機畫面影像。

狀態清單按一下可查看所有的事件和錄影記錄、依日期搜尋想要的記錄。

6.1.3. 常用功能

錄影設定

若要在 DVR 端觸發事件時，遠端也同時進行錄影備份，請按一下 “ ” (其他控制功能) → “ ” (錄影設定) 進

入 “Record Setting” (錄影設定) 頁面。

REMOTE OPERATION

在此頁面可以設定以下功能：

‧錄影類型 ‧硬碟覆寫 ‧事件前 / 後錄影時間 ‧錄影時間設定 ‧錄影檔案存放路徑

若勾選了 “Manual” (手動)，則按 “ ” (錄影) 就會立即啟動手動錄影，而且錄影檔會儲存在您指定的位置。影像

顯示畫面的左上角會顯示 “REC” 紅色字樣。

若勾選了 “Motion” (位移偵測) 和 / 或 “Alarm” (警報)，則當 DVR 端有觸發事件時，遠端也會立即啟動錄影功能，而且錄影檔會儲存在您指定的位置。

影像回放

若要回放錄影檔，請按 “ ” (其他控制功能) → “ ” (狀態清單)，然後選擇 “Record” (錄影) 標籤或 “Backup”

(備份) 標籤。預設會顯示所有的錄影檔清單，您也可以依類型列出想要的記錄來加快搜尋的速度。

若要立即回放某錄影檔，請從清單選取一筆記錄，然後按 “Play” (播放) 按鈕，或者連按兩下選取的記錄進行回放。之後會跳出頻道選取視窗，請從下拉式清單選取想要回放的頻道。

接著按 “Play” (播放)，就會在主控制面板下方出現回放控制面板：

REMOTE OPERATION

網路備份

按一下 “ ” (其他控制功能) → “ ” (備份) 進入頁面，然後就可以選取要遠端備份特定時間範圍內的影像資

料，或者備份特定事件的影像資料。

註：在啟動網路備份功能之前，請確認 DVR 沒有在回放模式下，否則 DVR 將會停止回放。

功能說明

IP Address / Port / User Name / Password (IP 位址 / 埠號 / 使用者名稱 / 密碼)

檢查您要取得影像資料的 DVR 網路連線資訊是否正確。

HDD Number / Channel (硬碟編號 / 頻道)

指定擁有您要備份之資料的硬碟和頻道。

下載指定時間內的影像資料在 “Start Time” (開始時間) 和 “End Time” (結束時間) 欄位指定您要

備份的時間範圍。

下載指定事件的影像資料從右側的事件清單中選取您要下載的特定事件。此清單由上而下會先顯

示最近一筆的事件再依序顯示發生時間較早的事件。

‧若要快速找出特定事件，請勾選或取消勾選 “System” (系統) /

“Manual” (手動) / “Alarm” (警報) / “Motion” (位移偵測) 事件類型，然後選取想要的事件。

‧若想要查看較早或較晚的事件記錄，而該記錄沒有顯示在目前的頁面

中時，請按一下 “Prev.Page” (上一頁) 或 “Next Page” (下一頁)。

‧若要更新事件清單，請按一下 “Reload” (重新載入)。

File Path (檔案位置) 指定備份下來的檔案要儲存的位置。

Simultaneous Playback (同步播放) 若要在下載時同步觀看備份的影像，請先勾選

“Simultaneous Playback” (同步播放)。您會在下載備份影像到電腦時

看見影像內容。

若只要下載備份影像而不要預覽，請取消選取 “Simultaneous Playback” (同步播放)。您只會看見一個訊息方塊，指出下載所需的總時間、目前的狀態和儲存位置。

Download / Cancel (下載 / 取消)

按一下 “Download” (下載) 開始備份影像，或 “Cancel” (取消) 不要備份影像。

REMOTE OPERATION

6.2. IE 網路瀏覽器

註：支援的電腦作業系統為 Windows Vista / XP / 2000。

步驟1：將DVR 的 IP 位址鍵入 URL 位址列 (例如 60.121.46.236)，然後按 Enter 鍵。之後會提示您輸入使用者名稱

和密碼來登入 DVR。

如果您設定的 TCP 埠並非 80 埠，就需要另行輸入埠號，格式為 IP

位址:埠號

。舉例來說，若 IP 位址為

60.121.46.236 且埠號為 888，請在 URL 網址列中輸入 ”http://60.121.46.236:888”，然後按 “Enter”。

步驟2：輸入使用者名稱和密碼，即與 Video Viewer 登入時使用的使用者名稱和密碼相同，然後按 “OK”。若登入資訊

正確，您將會看到和以下類似的畫面。

註：以下說明的按鍵和功能也許會和實際看到的有所差異，而且僅限特定型號才可使用。

功能說明

首頁

按

可回到 DVR 主要頁面。

設定

按

可進入詳細的 DVR 設定頁面。

PTZ

按

可進入 PTZ 模式。

頻道選擇

按一下頻道編號可觀看選取頻道的即時畫面。

您也可以按

或觀看前一個 / 下一個頻道。

顯示模式

按一下您要的顯示模式。共有三種模式可供選擇：

按

/ / 可分別顯示 4 分割 / 9 分割 / 16 分割畫面。

快照

按

可擷取目前畫面的快照，並開啟另一個瀏覽器視窗顯示擷取的影像。

選取

按

或觀看前一個 / 下一個頻道或變更設定。

四分割跳台 /

全螢幕跳台

四分割跳台按一下顯示 4 分割畫面。

若要退出此模式，請按其他頻道顯示按鈕。

全螢幕跳台按一下可依序顯示每個頻道，從 CH1 開始。顯示最後一個頻道後，就會從 CH1 開始從頭再來。若要退出此模式，請按其他頻道顯示按鈕。

REMOTE OPERATION

功能說明

網路傳輸

MPEG4 / QuickTime

QuickTime 是 Apple 公司的多媒體播放軟體。您必須先將 QuickTime 安裝到您的作業系統。選取 “QuickTime” 後，會提示您輸入存取 DVR 系統的使用者名稱和密碼。

REMOTE OPERATION

6.3. QuickTime 多媒體播放軟體

您也可以使用 QuickTime 多媒體播放軟體來遠端登入 DVR，並只能觀看即時畫面。當 DVR 在 CIF 錄影模式下時才能使用 QuickTime 存取。

註： QuickTime 是 Apple 公司的多媒體播放軟體。您必須先將 QuickTime 安裝到您的作業系統，然後才能存取 DVR

觀看即時畫面。若已安裝了 QuickTime，請跳過步驟 1。

註：本說明書付梓時的最新 QuickTime 版本為 V6.4，支援的作業系統為 Windows Vista / XP / 2000，以及 Apple

Mac。

步驟1：進入Apple 的官方網站來下載 QuickTime。網站位置如下：

http://www.apple.com/quicktime/win.html a). 按一下 “FFrreeee DDoowwnnllooaadd” (免費下載) 進入下載頁面，然後選擇下載免費的播放軟體。 b). 輸入您的電子郵件地址，然後按 “FFrreeee DDoowwnnllooaadd NNooww” (立即免費下載) 來下載最新版的 QuickTime

多媒體播放軟體。

c). 下載結束後，執行 “QQuuiicckkTTiimmeeIInnssttaalllleerr..eexxee” 檔，然後遵照螢幕上的指示完成安裝程序。

步驟2：開啟QuickTime 多媒體播放軟體。選擇 “File” (檔案) → “Open URL in New Player…” (在新的播放器開啟

URL)，然後輸入 URL 位址。 URL 位址的格式為 “rtsp://IP 位址:埠號/live/mpeg4” (例如：“rtsp://59.124.231.75/live/mpeg4”).

按一下 “OK” (確定) 繼續。

步驟3：之後會出現蹦現式視窗，提示您輸入授權資訊。

註：若沒有提示您輸入授權資訊，並出現錯誤代碼 10060 ，請進入 “Edit”  “Preferences” 

“QuickTime Preferences”，然後從下拉式選單選擇 “Streaming Transport”。選取 “Use HTTP”，並確認連接埠 ID 為 80。

輸入存取 DVR 所需的使用者名稱和密碼。使用者名稱和密碼就是您用來登入 Video Viewer 的使用者名稱和密碼。若資訊正確，按一下 “OK” 繼續。若資訊錯誤，按 “Cancel” 取消 DVR 存取。

步驟4：若登入成功，就會看見即時畫面。

附錄 1 PIN 腳解說

‧ 16 路 DVR

蜂鳴器當 DVR 有警報或位移偵測觸發事件發生，COM 會與 NO 連接，閃燈蜂鳴器會開始鳴叫且閃爍。

磁簧關關當磁簧開關被打開時，主機會發出警報且觸發錄影。

PIN 腳

功能說明

1 GND 接地

2~9 ALARM INPUT

使用連接線將 ALARM INPUT (PIN 2 -- 9) 和 GND (PIN 1) 接頭連接在一起。一但觸發警報後，

DVR 便會開始錄影，而且會發出警示音。 PIN 2 是Alarm 1。一旦觸發了警報，DVR 的CH1 便會開始進行警報錄影。 PIN 3 是Alarm 3。一旦觸發了警報，DVR 的CH3 便會開始進行警報錄影。 PIN 4 是Alarm 5。一旦觸發了警報，DVR 的CH5 便會開始進行警報錄影。 PIN 5 是Alarm 7。一旦觸發了警報，DVR 的CH7 便會開始進行警報錄影。 PIN 6 是Alarm 9。一旦觸發了警報，DVR 的CH9 便會開始進行警報錄影。 PIN 7 是Alarm 11。一旦觸發了警報，DVR 的CH11 便會開始進行警報錄影。 PIN 8 是Alarm 13。一旦觸發了警報，DVR 的CH13 便會開始進行警報錄影。 PIN 9 是Alarm 15。一旦觸發了警報，DVR 的CH15 便會開始進行警報錄影。

10 EXTERNAL INPUT 1

11 EXTERNAL OUTPUT 1

12 RS485-A

13 EXTERNAL ALARM NO

平常模式下，COM 與 NC 相連，與 NO 不相連。但是當警報被觸發時，COM 與 NO 相連。

注意：電壓上限為 DC24V 1A。

14 EXTERNAL INPUT 0

15~22 ALARM INPUT

使用連接線將 ALARM INPUT (PIN 15 – 22) 和 GND (PIN 1) 接頭連接在一起。一但觸發警報後，

DVR 便會開始錄影，而且會發出警示音。 PIN 15 是Alarm 2。一旦觸發了警報，DVR 的CH2 便會開始進行警報錄影。 PIN 16 是Alarm 4。一旦觸發了警報，DVR 的CH4 便會開始進行警報錄影。 PIN 17 是Alarm 6。一旦觸發了警報，DVR 的CH6 便會開始進行警報錄影。 PIN 18 是Alarm 8。一旦觸發了警報，DVR 的CH8 便會開始進行警報錄影。 PIN 19 是Alarm 10。一旦觸發了警報，DVR 的CH10 便會開始進行警報錄影。 PIN 20 是Alarm 12。一旦觸發了警報，DVR 的CH12 便會開始進行警報錄影。 PIN 21 是Alarm 14。一旦觸發了警報，DVR 的CH14 便會開始進行警報錄影。 PIN 22 是Alarm 16。一旦觸發了警報，DVR 的CH16 便會開始進行警報錄影。

23 EXTERNAL INPUT 0

24 RS485-B

25 EXTERNAL ALARM COM

平常模式下，COM 與 NC 相連，與 NO 不相連。但是當警報被觸發時，COM 與 NO 相連。

注意：電壓上限為 DC24V 1A。

附錄 1 PIN 腳解說

‧ 8 路 DVR

蜂鳴器當 DVR 有警報或位移偵測觸發事件發生，COM 會與 NO 連接，閃燈蜂鳴器會開始鳴叫且閃爍。

磁簧關關當磁簧開關被打開時，主機會發出警報且觸發錄影。

PIN 腳

功能說明

1 GND 接地

2~5 ALARM INPUT

使用連接線將ALARM INPUT (PIN 2 – 5) 和 GND (PIN 1) 接頭連接在一起。一但觸發警報後，DVR

便會開始錄影，而且會發出警示音。

PIN 2 是Alarm 1。一旦觸發了警報，DVR 的CH1 便會開始進行警報錄影。 PIN 3 是Alarm 3。一旦觸發了警報，DVR 的CH3 便會開始進行警報錄影。 PIN 4 是Alarm 5。一旦觸發了警報，DVR 的CH5 便會開始進行警報錄影。 PIN 5 是Alarm 7。一旦觸發了警報，DVR 的CH7 便會開始進行警報錄影。

10 EXTERNAL INPUT 1

11 EXTERNAL OUTPUT 1

12 RS485-A

13 EXTERNAL ALARM NO

平常模式下，COM 與 NC 相連，與 NO 不相連。但是當警報被觸發時，COM 與 NO 相連。

注意：電壓上限為 DC24V 1A。

14 EXTERNAL INPUT 0

15~18 ALARM INPUT

使用連接線將 ALARM INPUT (PIN 15 – 18) 和 GND (PIN 1) 接頭連接在一起。一但觸發警報後，

23 EXTERNAL INPUT 0

24 RS485-B

25 EXTERNAL ALARM COM

平常模式下，COM 與 NC 相連，與 NO 不相連。但是當警報被觸發時，COM 與 NO 相連。

注意：電壓上限為 DC24V 1A。

附錄 2 疑難排解

請參閱下列常見問題的回覆，使您能解決簡單的疑問。下表描述了一些典型的問題與其解答。請先閱讀後，若仍有疑問，再洽您的 DVR 經銷商。

‧ FAQ (常見問題)

問題解答

檢查電源線是否接好。沒有電源

確認電源插座有提供電力。

按按鍵時，沒有反應您也許處於 “按鍵鎖” 模式。按任何一個按鍵，在解除按鍵鎖的視窗中輸入密碼。

更換其他品牌的硬碟。無法偵測到硬碟

更換其他硬碟排線試試看。

更換其他品牌的 USB 隨身碟。無法偵測到 USB 裝置

將 USB 隨身碟格式化為 FAT32，然後再試一次。

請確認攝影機有接上電源。

請確認攝影機內有安裝鏡頭。.

請確認螢幕功能正常、影像線連接正常。

無即時影像

請確認攝影機功能正常、影像線連接正常。

請確認硬碟的安裝與連接正常。有錄影，但沒有錄影檔案

請確認 “手動錄影” 已設為 “ON”，而且 “攝影機” 目錄選單的錄影功能也設為 “ON”。

預約錄影的功能沒反應請確認 “預約錄影” 選項已設為 “ON”，而且也已設好預約錄影排程。

請確認 “事件錄影” 選項功能已設為 “ON”。

請確認位移偵測目錄選單的 “偵測” 選項已設為 “ON”。

位移偵測錄影的功能沒反應

請確認已設好位移偵測區域。

無法在 DVR 回放錄影畫面若要能正常回放錄影檔案，請至少必須錄超過 8192 張畫面。不然 DVR 就無法進行

回放。例如，如果您將 IPS 設為 30，若要正常回放檔案，則錄影時間至少必須超過 273

秒 (8192 張影像 / 30 IPS)。

確認 DVR 有支援錄音功能。

確認攝影機有支援錄音功能。

無法備份影音檔案資料

確認攝影機連接的頻道為支援錄音的頻道。

檢查 DVR 的韌體版本。無法透過 IE 瀏覽器遠端監看 DVR 畫面

出現蹦現式訊息時，請選擇允許網路瀏覽器 ActiveX 或 applet。

您必須擁有 ”總管理者” 的權限才能執行此功能。

檢查網路連線資訊是否正確：IP 位址 / 埠號 / 使用者名稱 / 密碼。

從遠端電腦備份 DVR 的錄影資料失敗。

指定擁有您要備份之資料的硬碟和頻道。

請確認 USB 隨身碟格式為 FAT32。升級韌體 / OSD 檔失敗

請確認韌體 / OSD 檔案是否正確。

確認 DVR 是否支援 IR 遙控器。

請確認是否有安裝電池。

無法使用 IR 紅外線遙控器

對準 IR 紅外線接收區，然後再試一次。

附錄 3 相容 USB 隨身碟品牌

請先將 DVR 的韌體版本更新，以確保下表的正確性。若 DVR 與 USB 隨身碟不相容，螢幕上會出現「USB 錯誤」的訊息。

註：請先在電腦中將 USB 隨身碟的格式格式化成 “FAT32”。

註： USB 備份一次最多只能備份 2GB 的影像檔案。若要備份更多錄影資料，請再設定一次時間和想要備份的頻道，然

後再次啟動 USB 備份功能。

品牌名稱型號容量

Transcend JFV35 4GB

JFV30 8GB

Kingston DataTraveler 1GB

PQI U172P 4GB

Apacer AH320 2GB

AH320A 8GB

AH220 1GB

AH320 4GB

A-data RB-18 1GB

Sandisk Cruzer Micro 2GB

Cruzer Micro 4GB

Cruzer4-pk 2GB

Netac U208 1GB

MSI F200 4GB

SONY Micro Vault Tiny 2G 2GB

Micro Vault Tiny 4G 4GB

Micro Vault Tiny 1GB

附錄 4 相容 SATA 硬碟表

品牌名稱型號容量轉速

ST3320613AS 320GB 7200 rpm

ST33500320AS 500GB 7200 rpm

ST3750330AS 750GB 7200 rpm

Seagate

ST31000340AS 1000GB 7200 rpm

WD3200AAKS 320GB 7200 rpm

WD5000AACS 500GB 7200 rpm

WD6400AAKS 640GB 7200 rpm

WD7500AAKS 750GB 7200 rpm

STM3500320AS 500GB 7200 rpm Maxtor

STM3750330AS 750GB 7200 rpm

HDT725032VLA360 320GB 7200 rpm HITACHI

HDS721010KLA330 1000GB 7200 rpm

附錄 5 相容 USB DVD 燒錄機表

註：下列晶片組僅供參考用。為確保相容性，請使用以下指定的型號。

品牌名稱

型號晶片組

BENQ EW200G MediaTek

LiteOn DH-20A4P MediaTek

DRU-V200S NEC SONY

AD-7200A NEC

GH22NP20 Panasonic LG

GH20NS15 Renesas

附錄 6 RS485 通訊協定

 使用電腦鍵盤模擬 DVR 面板按鍵。  資料：遠端協定使用 8 個位元資料、1 個開始位元、1 個停止位元。

功能

CODE ASCII

功能

CODE ASCII

KEY_MENU 0x4D M KEY_SET_CHANNEL 0x6e n

KEY_ENTER 0x0D ENTER KEY_DWELL 0x65 e

KEY_PLUS 0x6b k KEY_CH1 0x31 1

KEY_MINUS 0x6d m KEY_CH2 0x32 2

KEY_UP 0x55 U KEY_CH3 0x33 3

KEY_DOWN 0x4E N KEY_CH4 0x34 4

KEY_LEFT 0x4C L KEY_CH5 0x35 5

KEY_RIGHT 0x52 R KEY_CH6 0x36 6

KEY_POWER 0x57 W KEY_CH7 0x37 7

KEY_REC 0x72 r KEY_CH8 0x38 8

KEY_PLAY 0x50 P KEY_CH9 0x39 9

KEY_SLOW 0x53 S KEY_CH10 0x41 A

KEY_ZOOM 0x5A z KEY_CH11 0x42 B

KEY_KEY LOCK 0x4B K KEY_CH12 0x43 C

KEY_AUDIO 0x64 d KEY_CH13 0x44 D

KEY_SEARCH 0x73 S KEY_CH14 0x45 E

KEY_PTZ_MODE 0x70 p KEY_CH15 0x46 F

KEY_PTZ_PRESET 0x71 q KEY_CH16 0x47 G

KEY_PTZ_ZOOM_IN 0x69 i KEY_EJECT_DVD 0x6a j

KEY_PTZ_ZOOM_OUT 0x66 f KEY_IRIS_NEAR 0x67 g

KEY_MODE 0x6f o KEY_IRIS_FAR 0x68 h

KEY_4 CUT 0x61 a KEY_PTZ_LIGHT 0x6c l

KEY_9 CUT 0x62 b KEY_PTZ_WIPER 0x77 w

KEY_16 CUT 0x63 c

附錄 7 產品規格

‧ Model 1 ~ 4

型號 Model 1 Model 2 Model 3 Model 4

影像系統 NTSC / PAL (自動偵測)

影像輸入

(composite video signal 1 Vp-p 75Ω BNC)

16 路 8路

影像輸出 (composite video signal 1 Vp-p 75Ω BNC)

主螢幕輸出

聲音輸入 / 輸出

4 路輸入、1 路輸出

(單聲道)

1 路輸入、1 路輸出

(單聲道)

4 路輸入、1 路輸出

(單聲道)

1 路輸入、1 路輸出

(單聲道)

最大解析度 (Frame)

120 IPS @ 704×480 <NTSC> /

100 IPS @ 704×576 <PAL>

60 IPS @ 704×480 <NTSC> /

50 IPS @ 704×576 <PAL>

最大解析度 (Field)

240 IPS @ 704×240

<NTSC> /

200 IPS @ 704×288

<PAL>

無

120 IPS @ 704×240

<NTSC> /

100 IPS @ 704×288

<PAL>

無

最大解析度 (CIF)

480 IPS @ 352×240 <NTSC> /

400 IPS @ 352×288 <PAL>

240 IPS @ 352×240 <NTSC> /

200 IPS @ 352×288 <PAL>

錄影速度 (Frame)

120、60、30、15 IPS <NTSC> /

100、50、25、12 IPS <PAL>

60、30、15、7 IPS <NTSC> /

50、25、12、6 IPS <PAL>

錄影速度 (Field)

240、120、60、30 IPS

<NTSC> /

200、100、50、25 IPS

<PAL>

無

120、60、30、15 IPS

<NTSC> /

100、50、25、12 IPS

<PAL>

無

錄影速度 (CIF)

480、240、120、60 IPS <NTSC> /

400、200、100、50 IPS <PAL>

240、120、60、30 IPS <NTSC> /

200、100、50、25 IPS <PAL>

多語 OSD 支援有

影像品質設定最好、高、一般和基本

硬碟儲存容量可容納兩顆 SATA 硬碟 ( 1 顆硬碟最多支援 1TB 容量)

快速搜尋時間 / 位移 / 警報

三種搜尋模式

時間 / 位移

二種搜尋模式

時間 / 位移 / 警報

三種搜尋模式

時間 / 位移

二種搜尋模式

SATA 介面內建

VGA 介面

內建 (最大輸出解析度高

達 1600 x 1200)

無

內建 (最大輸出解析度高

達 1600 x 1200)

無

錄影模式

手動 / 預約 / 位移偵測 /

警報 / 遠端

手動 / 預約 / 位移偵測 /

遠端

手動 / 預約 / 位移偵測 /

警報 / 遠端

手動 / 預約 / 位移偵測 /

遠端

顯示速度 480 IPS <NTSC> / 400 IPS <PAL> 240 IPS <NTSC> / 200 IPS <PAL>

多工操作支援

即時顯示 / 錄影 (16 路) / 回放 (最多同時回放四路) /

備份 / 網路遠端操作

即時顯示 / 錄影 (8 路) / 回放 (最多同時回放四路) / 備

份 / 網路遠端操作

遠端獨立操作完全遠端獨立操作

R.E.T.R. (遠端事件觸發錄影)

有無有無

位移偵測區域

每隻攝影機的偵測區域皆

可分為 16 * 12 個方格

三種預設偵測區域可供選擇每隻攝影機的偵測區域皆

可分為 16 * 12 個方格

三種預設偵測區域可供選

擇

位移偵測靈敏度一種參數，三個設定選項 (高 / 一般 / 低)

附錄 7 產品規格

型號 Model 1 Model 2 Model 3 Model 4

警報前錄影有 (8 MB)

備份裝置 1. USB DVD 燒錄機 (選購); 2. USB 2.0 隨身碟; 3. 網路

USB 介面

前面板 * 1 /

背板 * 1

前面板 * 1

前面板 * 1 /

背板 * 1

前面板 * 1

乙太網路 10/100 Base-T，支援網路遠端監控功能

支援隨附軟體 “Video Viewer” / Internet Explorer & Mozilla Firefox 網路瀏覽器 /

QuickTime 多媒體播放軟體 (最多支援同時五人上線)

網路介面

*作業系統：Windows Vista / XP / 2000；Apple Mac

遠端警報通知透過 E-mail 或 FTP 無透過 E-mail 或 FTP 無

網路通訊協定 TCP/IP、PPPOE、DHCP 和 DDNS

IR 紅外線遙控有 (IR 接收器內建)

PTZ 攝影機控制有

跳台停留時間可設定跳台停留時間 (3 / 5 / 10 / 15 秒)

警報輸入 / 輸出 16 個輸入、1 個輸出無 8個輸入、1 個輸出無

影像縮放兩倍數位變焦 (即時 & 回放)

按鍵鎖 (密碼保護) 有

影像遺失偵測有

攝影機名稱最多支援六個字元

影像調整色相 / 飽和度 / 對比度 / 亮度

日期顯示格式年/月/日、日/月/年、月/日/年

日光節約有

電源輸入 (±10%) DC 19V

電源消耗功率 (±10%) ＜64 W

操作溫度 10℃ ~ 40℃ (50℉~104℉)

尺寸 (mm)** 430(W) x 65(H) x 338(D)

系統回復停電後復電，可自動恢復事先狀態

選購配備控制鍵盤控制鍵盤 / VGA 轉接卡控制鍵盤控制鍵盤 / VGA 轉接卡

* 產品規格以實機為準，規格修改將不另行通知。 ** 尺寸公差：±5mm

附錄 7 產品規格

‧ Model 5 ~ 8

型號 Model 5 Model 6 Model 7 Model 8

影像系統 NTSC / PAL (自動偵測)

影像輸入

(composite video signal 1 Vp-p 75Ω BNC)

16 路 8路

影像輸出 (composite video signal 1 Vp-p 75Ω BNC)

主螢幕輸出

聲音輸入 / 輸出

4 路輸入、1 路輸出

(單聲道)

1 路輸入、1 路輸出

(單聲道)

4 路輸入、1 路輸出

(單聲道)

1 路輸入、1 路輸出

(單聲道)

最大解析度 (Frame)

704×480 pixels with 120 IPS <NTSC> /

704×576 pixels with 100 IPS <PAL>

704×480 pixels with 60 IPS <NTSC> /

704×576 pixels with 50 IPS <PAL>

最大解析度 (Field)

704×240 pixels with

240 IPS <NTSC> /

704×288 pixels with

200 IPS <PAL>

無

704×240 pixels with

120 IPS <NTSC> /

704×288 pixels with

100 IPS <PAL>

無

最大解析度 (CIF)

352×240 pixels with 480 IPS <NTSC> /

352×288 pixels with 400 IPS <PAL>

352×240 pixels with 240 IPS <NTSC> /

352×288 pixels with 200 IPS <PAL>

錄影速度 (Frame)

120、60、30、15 IPS <NTSC> /

100、50、25、12 IPS <PAL>

60、30、15、7 IPS <NTSC> /

50、25、12、6 IPS <PAL>

錄影速度 (Field)

240、120、60、30 IPS

<NTSC> /

200、100、50、25 IPS

<PAL>

無

120、60、30、15 IPS

<NTSC> /

100、50、25、12 IPS

<PAL>

無

錄影速度 (CIF)

480、240、120、60 IPS <NTSC> /

400、200、100、50 IPS <PAL>

240、120、60、30 IPS <NTSC> /

200、100、50、25 IPS <PAL>

多語 OSD 支援有

影像品質設定最好、高、一般和基本

硬碟儲存容量可容納兩顆 SATA 硬碟 ( 1 顆硬碟最多支援 1TB 容量)

快速搜尋時間 / 位移 / 警報

三種搜尋模式

時間 / 位移

二種搜尋模式

時間 / 位移 / 警報

三種搜尋模式

時間 / 位移

二種搜尋模式

SATA 介面內建

VGA 介面

內建 (最大輸出解析度高

達 1600 x 1200)

無

內建 (最大輸出解析度高

達 1600 x 1200)

無

錄影模式

手動 / 預約 / 位移偵測

/ 警報 / 遠端

手動 / 預約 / 位移偵測

/ 遠端

手動 / 預約 / 位移偵測

/ 警報 / 遠端

手動 / 預約 / 位移偵測

/ 遠端

顯示速度 480 IPS <NTSC> / 400 IPS <PAL> 240 IPS <NTSC> / 200 IPS <PAL>

多工操作支援

即時顯示 / 錄影 (16 路) / 回放 (最多同時回放四路) /

備份 / 網路遠端操作

即時顯示 / 錄影 (8 路) / 回放 (最多同時回放四路) /

備份 / 網路遠端操作

遠端獨立操作完全遠端獨立操作

R.E.T.R. (遠端事件觸發錄影)

有無有無

位移偵測區域

每隻攝影機的偵測區域皆

可分為 16 * 12 個方格

三種預設偵測區域可供

選擇

每隻攝影機的偵測區域皆

可分為 16 * 12 個方格

三種預設偵測區域可供

選擇

位移偵測靈敏度一種參數，三個設定選項 (高 / 一般 / 低)

警報前錄影有 (8 MB)

附錄 7 產品規格

型號 Model 5 Model 6 Model 7 Model 8

備份裝置

1. DVD 燒錄機 (選購)

2. USB 2.0 隨身碟

3. 網路

1. USB DVD 燒錄機 (選購)

2. USB 2.0 隨身碟

3. 網路

1. DVD 燒錄機 (選購)

2. USB 2.0 隨身碟

3. 網路

1. USB DVD 燒錄機 (選購)

2. USB 2.0 隨身碟

3. 網路

USB 介面前面板 * 1

乙太網路 10/100 Base-T，支援網路遠端監控功能

支援隨附軟體 “Video Viewer” / Internet Explorer & Mozilla Firefox 網路瀏覽器 /

QuickTime 多媒體播放軟體 (最多支援同時五人上線)

網路介面

*作業系統：Windows Vista / XP / 2000；Apple Mac

遠端警報通知透過 E-mail 或 FTP 無透過 E-mail 或 FTP 無

網路通訊協定 TCP/IP、PPPOE、DHCP 和 DDNS

IR 紅外線遙控有 (IR 接收器內建)

PTZ 攝影機控制有

跳台停留時間可設定跳台停留時間 (3 / 5 / 10 / 15 秒)

警報輸入 / 輸出 16 個輸入、1 個輸出無 8個輸入、1 個輸出無

影像縮放兩倍數位變焦 (即時 & 回放)

按鍵鎖 (密碼保護) 有

影像遺失偵測有

攝影機名稱最多支援六個字元

影像調整色相 / 飽和度 / 對比度 / 亮度

日期顯示格式年/月/日、日/月/年、月/日/年

日光節約有

電源輸入 (±10%) DC 19V

電源消耗功率 (±10%) ＜64 W

操作溫度 10℃ ~ 40℃ (50℉~104℉)

尺寸 (mm)** 430(W) x 65(H) x 338(D)

系統回復停電後復電，可自動恢復事先狀態

選購配備控制鍵盤控制鍵盤 / VGA 轉接卡控制鍵盤控制鍵盤 / VGA 轉接卡

* 產品規格以實機為準，規格修改將不另行通知。 ** 尺寸公差：±5mm

附錄 8 錄影時間表

以下數據的測試環境為一般辦公室，僅供參考用。

錄影時間會受到以下三項因素而有變動：

‧ 攝影機解析度； ‧ 畫面複雜度； ‧ 物體移動的頻率。

16 路 DVR

錄影模式錄影品質

IPS

750GB 錄影時間 (小時) 750GB 錄影時間 (天)

FRAME 最好 120 151.33 6.31

60 217.77 9.07

30 393.91 16.41

15 558.04 23.25 高 120 202.92 8.46

60 322.72 13.45

30 496.03 20.67

15 622.92 25.96 一般 120 243.51 10.15

60 382.65 15.94

30 595.24 24.80

15 765.31 31.89 基本 120 293.70 12.24

60 469.92 19.58

30 669.64 27.90

15 892.86 37.20 FIELD 最好 240 153.94 6.41

120 267.86 11.16

60 398.60 16.61

30 572.34 23.85 高 240 192.70 8.03

120 314.39 13.10

60 385.25 20.22

30 656.51 27.35 一般 240 200.94 8.37

120 360.02 15.00

60 519.10 21.63

30 720.05 30.00 基本 240 261.32 10.89

120 413.36 17.22

60 653.31 27.22

30 892.86 37.20 CIF 最好 480 111.61 4.65

240 191.33 7.97

120 343.41 14.31

60 505.39 21.06 高 480 145.57 6.07

240 199.89 8.33

120 412.09 17.17

60 637.76 26.57 一般 480 169.10 7.05

240 297.62 12.40

120 491.48 20.48

60 744.05 31.00 基本 480 221.37 9.22

240 382.65 15.94

120 622.92 25.96

60 892.86 37.20

附錄 8 錄影時間表

8 路 DVR

錄影模式錄影品質

IPS

750GB 錄影時間 (小時) 750GB 錄影時間 (天)

FRAME 最好 60 302.66 12.61

30 435.54 18.15

15 787.82 32.83

7 1116.07 46.50 高 60 405.84 16.91

30 645.44 26.89

15 992.06 41.34

7 1245.85 51.91 一般 60 487.01 20.29

30 765.31 31.89

15 1190.48 49.60

7 1530.61 63.78 基本 60 587.41 24.48

30 939.85 39.16

15 1339.29 55.80

7 1785.71 74.40 FIELD 最好 120 307.88 12.83

60 535.71 22.32

30 797.19 33.22

15 1144.69 47.70 高 120 385.41 16.06

60 628.77 26.20

30 970.50 40.44

15 1313.03 54.71 一般 120 401.89 16.75

60 720.05 30.00

30 1038.21 43.26

15 1440.09 60.00 基本 120 522.65 21.78

60 826.72 34.45

30 1306.62 54.44

15 1785.71 74.40 CIF 最好 240 223.21 9.30

120 382.65 15.94

60 686.81 28.62

30 1010.78 42.12 高 240 291.15 12.13

120 399.79 16.66

60 824.18 34.34

30 1275.51 53.15 一般 240 338.20 14.09

120 595.24 24.80

60 982.96 40.96

30 1488.10 62.00 基本 240 442.74 18.45

120 765.31 31.89

60 1245.85 51.91

30 1785.71 74.40

Avtech AVC-756D, KPD678, AVC757, KPD677, AVC755 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual