393Z
489a_V1.0
USER MANUAL
High Resolution Dome Camera
Please read the instructions thoroughly before using the product.
393Z
489a_V1.0
USER MANUAL
High Resolution Dome Camera
Please read the instructions thoroughly before using the product.
IMPORTANT SAFEGUARD
All lead-free products offered by the company comply with the requirements of the European law on the Restriction of
Hazardous Substances (RoHS) directive, which means our manufacture processes and products are strictly
“lead-free” and without the hazardous substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected
separately at the product end-of-life. This applies to your product and any peripherals marked with this symbol. Do
not dispose of these products as unsorted municipal waste. Contact your local dealer for procedures for recycling this
equipment.
CE Mark
This apparatus is manufactured to comply with the radio interference.
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital service, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This equipment
generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
IMPORTANT SAFEGUARD
All lead-free products offered by the company comply with the requirements of the European law on the Restriction of
Hazardous Substances (RoHS) directive, which means our manufacture processes and products are strictly
“lead-free” and without the hazardous substances cited in the directive.
The crossed-out wheeled bin mark symbolizes that within the European Union the product must be collected
separately at the product end-of-life. This applies to your product and any peripherals marked with this symbol. Do
not dispose of these products as unsorted municipal waste. Contact your local dealer for procedures for recycling this
equipment.
CE Mark
This apparatus is manufactured to comply with the radio interference.
Federal Communications Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital service, pursuant to Part 15 of the FCC rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment. This equipment
generates, uses, and can radiate radio frequency energy. If not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device mat not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate this equipment.
All external cables connecting to this basic unit must be shielded.
For cables connecting to PCMCIA cards, see the option manual or installation instructions.
Disclaimer
We reserve the right to revise or remove any content in this manual at any time. We do not warrant or assume any legal liability or
responsibility for the accuracy, completeness, or usefulness of this manual. The content of this manual is subject to change without
notice.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device mat not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate this equipment.
All external cables connecting to this basic unit must be shielded.
For cables connecting to PCMCIA cards, see the option manual or installation instructions.
Disclaimer
We reserve the right to revise or remove any content in this manual at any time. We do not warrant or assume any legal liability or
responsibility for the accuracy, completeness, or usefulness of this manual. The content of this manual is subject to change without
notice.
TABLE OF CONTENT
FEATURES ............................................................................................................. 1
PACKAGE CONTENT ............................................................................................1
SPECIFICATIONS*................................................................................................. 2
LENS ANGLE ADJUSTMENT................................................................................. 3
CONNECTION........................................................................................................ 3
INSTALLATION....................................................................................................... 4
CAMERA CONFIGURATION.................................................................................. 8
TABLE OF CONTENT
FEATURES ............................................................................................................. 1
PACKAGE CONTENT ............................................................................................1
SPECIFICATIONS*................................................................................................. 2
LENS ANGLE ADJUSTMENT................................................................................. 3
CONNECTION........................................................................................................ 3
INSTALLATION....................................................................................................... 4
CAMERA CONFIGURATION.................................................................................. 8
1
FEATURES
1. 1/3" color CCD sensor with SONY Effio DSP
2. High resolution
3. F1.4 Large aperture
4. f3.8 ~ f9.5mm vari-focal lens
5. Min. illumination of 0.05 Lux at F1.4
6. External alarm device connection
7. Customized OSD for camera configuration
8. Vandal-proof housing design (IPxx7)
PACKAGE CONTENT
Please make sure you have the following items in your sales package:
Vari-Focal Dome Camera with Power and Video Cable * 1
User Manual * 1
1
FEATURES
1. 1/3" color CCD sensor with SONY Effio DSP
2. High resolution
3. F1.4 Large aperture
4. f3.8 ~ f9.5mm vari-focal lens
5. Min. illumination of 0.05 Lux at F1.4
6. External alarm device connection
7. Customized OSD for camera configuration
8. Vandal-proof housing design (IPxx7)
PACKAGE CONTENT
Please make sure you have the following items in your sales package:
Vari-Focal Dome Camera with Power and Video Cable * 1
User Manual * 1
2
SPECIFICATIONS*
Pick up Element 1/3" Color CCD image sensor with SONY Effio DSP
Number of Pixel 768(H)x494(V) <NTSC> / 752(H)x582(V) <PAL>
Resolution Super High Resolution
Min. Illumination 0.05 Lux / F1.4
S/N Ratio More than 48dB (AGC off)
Electronic Shutter 1/60 (1/50) to 1/100,000 sec
Vari-focal Lens f3.8mm ~ f9.5mm
Lens Angle 85.4° ～ 36°
IRIS Mode AI / AES (Default)
White Balance ATW
IP Rating IPxx7
External Alarm Device Connection Alarm in
Video Output 1.0 Vp-p composite, 75
Power Source (±10%) DC12V / 70mA
Dimensions (mm)** 124.3(Ø) x 92(H)
* The specifications are subject to change without notice.
** Dimensional Tolerance: ± 5mm
2
SPECIFICATIONS*
Pick up Element 1/3" Color CCD image sensor with SONY Effio DSP
Number of Pixel 768(H)x494(V) <NTSC> / 752(H)x582(V) <PAL>
Resolution Super High Resolution
Min. Illumination 0.05 Lux / F1.4
S/N Ratio More than 48dB (AGC off)
Electronic Shutter 1/60 (1/50) to 1/100,000 sec
Vari-focal Lens f3.8mm ~ f9.5mm
Lens Angle 85.4° ～ 36°
IRIS Mode AI / AES (Default)
White Balance ATW
IP Rating IPxx7
External Alarm Device Connection Alarm in
Video Output 1.0 Vp-p composite, 75
Power Source (±10%) DC12V / 70mA
Dimensions (mm)** 124.3(Ø) x 92(H)
* The specifications are subject to change without notice.
** Dimensional Tolerance: ± 5mm
3
LENS ANGLE ADJUSTMENT
The lens can be panned left or right for angle adjustment, maximum 60°
respectively from the default position .
CONNECTION
1. Connect the power connector of the camera to a DC 12V regulated power
supply.
NOTE: Please use a regulated DC12V power adaptor to operate this unit. The power
tolerance of this unit is DC12V ± 10% (DC 10.8V ~ DC 13.2V). A power input of
more than the DC 13.2V will damage this unit.
2. Connect the camera video output to the input of the DVR with a 75 coaxial
cable.
3. (Optional) Connect to an alarm device as described in the manual of the alarm
device with the “Alarm in” and “GND” wires. Then, go to DVR’s menu
(ADVANCED CONFIG DETECTION ALARM) to enable alarm
detection.
3
LENS ANGLE ADJUSTMENT
The lens can be panned left or right for angle adjustment, maximum 60°
respectively from the default position .
CONNECTION
1. Connect the power connector of the camera to a DC 12V regulated power
supply.
NOTE: Please use a regulated DC12V power adaptor to operate this unit. The power
tolerance of this unit is DC12V ± 10% (DC 10.8V ~ DC 13.2V). A power input of
more than the DC 13.2V will damage this unit.
2. Connect the camera video output to the input of the DVR with a 75 coaxial
cable.
3. (Optional) Connect to an alarm device as described in the manual of the alarm
device with the “Alarm in” and “GND” wires. Then, go to DVR’s menu
(ADVANCED CONFIG DETECTION ALARM) to enable alarm
detection.
4
INSTALLATION
Step1 Remove the Dome Cover
Remove the Dome Cover by turning it
counterclockwise to the end and then
take it off.
Step2 Remove the Black Shield
Case
First, unscrew the Black Shield Case.
Then remove it by pressing the two
sides and then pulling it outward.
4
INSTALLATION
Step1 Remove the Dome Cover
Remove the Dome Cover by turning it
counterclockwise to the end and then
take it off.
Step2 Remove the Black Shield
Case
First, unscrew the Black Shield Case.
Then remove it by pressing the two
sides and then pulling it outward.
5
Step3 Align the screw holes
Rotate the lens plate to the front side of
the camera, and align the gaps on the
plate with the three screw holes
respectively as indicated below. Then,
aim the lens to the place you want to
watch.
Step4 Attach the camera to the
ceiling
A
ttach the camera to the ceiling with
three screws.
Then, connect the power and video
cable to the power supply and the
input of the DVR for later
adjustments.
Note:
1. Screws are not supplied with the sales
package. For installation, please
purchase the suitable screws.
2. For safety, always let the power and video
line concealed behind the installation
position.
5
Step3 Align the screw holes
Rotate the lens plate to the front side of
the camera, and align the gaps on the
plate with the three screw holes
respectively as indicated below. Then,
aim the lens to the place you want to
watch.
Step4 Attach the camera to the
ceiling
A
ttach the camera to the ceiling with
three screws.
Then, connect the power and video
cable to the power supply and the
input of the DVR for later
adjustments.
Note:
1. Screws are not supplied with the sales
package. For installation, please
purchase the suitable screws.
2. For safety, always let the power and video
line concealed behind the installation
position.
6
Step5 Adjust the angle of the camera
To adjust the angle of the camera, swivel the
black rotatable plate from the center to the left
or to the right, maximum 60° (Pan).
Adjust the tilt angle by moving the lens,
maximum 90° (Tilt).
Use a flat-headed screwdriver to loosen the
pivots on the lens. First adjust the 1
st
pivot to
zoom-in / out (Zoom). Second, adjust the 2
nd
pivot to fine-tune the clearness of the images.
Secure these two pivots after the adjustment
is completed.
Finally fasten the screw on the side of lens to
fix the tilt angle after the optimized positioning
is achieved.
Note: When adjusting the title angle, please do not tilt the camera lens more than 90°.
6
Step5 Adjust the angle of the camera
To adjust the angle of the camera, swivel the
black rotatable plate from the center to the left
or to the right, maximum 60° (Pan).
Adjust the tilt angle by moving the lens,
maximum 90° (Tilt).
Use a flat-headed screwdriver to loosen the
pivots on the lens. First adjust the 1
st
pivot to
zoom-in / out (Zoom). Second, adjust the 2
nd
pivot to fine-tune the clearness of the images.
Secure these two pivots after the adjustment
is completed.
Finally fasten the screw on the side of lens to
fix the tilt angle after the optimized positioning
is achieved.
Note: When adjusting the title angle, please do not tilt the camera lens more than 90°.
7
Step6 Replace the Black Shield
Case
Replace the Black Shield Case to the
camera base. Ensure that the Black
Shield Case does not cover the lens.
Step7 Replace the Dome Cover
Replace the dome cover to the camera
base and turn it clockwise to the end to
secure it.
7
Step6 Replace the Black Shield
Case
Replace the Black Shield Case to the
camera base. Ensure that the Black
Shield Case does not cover the lens.
Step7 Replace the Dome Cover
Replace the dome cover to the camera
base and turn it clockwise to the end to
secure it.
8
CAMERA CONFIGURATION
This camera has its own menu for parameter settings. To enter the menu, please
connect this camera with a DCCS-enabled DVR, or used with our control box,
AVK-T1, when it’s connected to a non-DCCS DVR.
Enter camera menu
Connect the supplied power adapter to the camera’s power jack on the rear
panel and the power outlet.
Below shows how to enter the camera menu with a DCCS-enabled DVR.
STEP1: When the DVR is powered on, check the channel with this camera
connected, and see if the DCCS connection icon
is shown.
STEP2: Enter the camera menu.
8
CAMERA CONFIGURATION
This camera has its own menu for parameter settings. To enter the menu, please
connect this camera with a DCCS-enabled DVR, or used with our control box,
AVK-T1, when it’s connected to a non-DCCS DVR.
Enter camera menu
Connect the supplied power adapter to the camera’s power jack on the rear
panel and the power outlet.
Below shows how to enter the camera menu with a DCCS-enabled DVR.
STEP1: When the DVR is powered on, check the channel with this camera
connected, and see if the DCCS connection icon
is shown.
STEP2: Enter the camera menu.
9
From DCCS menu
Right-click to display the DVR main menu, and select “ADVANCED
CONFIG“ “DCCS“.
ADVANCED CONFIG
C A N E R A CH1 CH2 CH3 CH4
DETECTION DIAGNOSTIC START
ALERT MENU SETUP
NETWORK
DISPLAY
RECORD
DEVICES
DCCS DEVICE OSD CAM
IVS CONNECTION OK
NOTIFY
EXIT
Select “MENU“ “SETUP“ to enter the camera menu.
To move between each option, select ““ / ““;
To change parameter values, select ““ / ““;
When you see
with an option, select “ “;
To exit the menu and return to the main menu, select “X“.
9
From DCCS menu
Right-click to display the DVR main menu, and select “ADVANCED
CONFIG“ “DCCS“.
ADVANCED CONFIG
C A N E R A CH1 CH2 CH3 CH4
DETECTION DIAGNOSTIC START
ALERT MENU SETUP
NETWORK
DISPLAY
RECORD
DEVICES
DCCS DEVICE CAMERA
IVS CONNECTION OK
NOTIFY
EXIT
Select “MENU“ “SETUP“ to enter the camera menu.
To move between each option, select ““ / ““;
To change parameter values, select ““ / ““;
When you see
with an option, select “ “;
To exit the menu and return to the main menu, select “X“.
10
Camera menu
SUB-MENU DESCRIPTION
SHUTTER / AGC 1. Select “AUTO” to allow the camera to act automatically when the light
condition of the environment changes.
2. Select “MANUAL” to fix the shutter and AGC modes of the camera no matter
how the light condition of the environment changes.
WHITE BAL Process the current image to retain color balance over a color temperature
range.
BACKLIGHT Adjust the image to compensate for an area that is overpowered by brightness
because of excessive light.
“BLC” is to automatically adjust the level of the light to show more details in the
dark environment.
“HLC” is to mask extremely bright areas.
PICT ADJUST Adjust the color of the pictures in, for example, brightness, contrast, sharpness
and hue.
ATR D-WDR to increase the image recognizability of the overexposed and dark
areas.
PRIVACY Mask areas that should be not visible.
DAY / NIGHT Set the night surveillance mode to color or B/W.
NR Reduce noise by separating luminance (Y) and chrominance (C) settings.
CAMERA ID Set the title of the camera.
LANGUAGE Select the language of the menu on-screen display.
CAMERA RESET Press to restore all settings to their factory default values.
10
Camera menu
SUB-MENU DESCRIPTION
SHUTTER / AGC 3. Select “AUTO” to allow the camera to act automatically when the light
condition of the environment changes.
4. Select “MANUAL” to fix the shutter and AGC modes of the camera no matter
how the light condition of the environment changes.
WHITE BAL Process the current image to retain color balance over a color temperature
range.
BACKLIGHT Adjust the image to compensate for an area that is overpowered by brightness
because of excessive light.
“BLC” is to automatically adjust the level of the light to show more details in the
dark environment.
“HLC” is to mask extremely bright areas.
PICT ADJUST Adjust the color of the pictures in, for example, brightness, contrast, sharpness
and hue.
ATR D-WDR to increase the image recognizability of the overexposed and dark
areas.
PRIVACY Mask areas that should be not visible.
DAY / NIGHT Set the night surveillance mode to color or B/W.
NR Reduce noise by separating luminance (Y) and chrominance (C) settings.
CAMERA ID Set the title of the camera.
LANGUAGE Select the language of the menu on-screen display.
CAMERA RESET Press to restore all settings to their factory default values.
11
Camera menu tree
SUB-MENU OPTIONS
AUTO HIGH
LUNINANCE
MODE AUTO IRIS /
SHUT+AUTO
IRIS
SHUTTER / AGC
BRIGHTNESS 0 ~ 255
LOW
LUMINANCE
MODE AGC / OFF
BRIGHTNESS x0.25 / x0.50 /
x0.75 / x1.00
MANUAL MODE SHUT + AGC
SHUTTER 1/50; 1/120; 1/250; 1/500; 1/1000;
1/2000; 1/4000; 1/10000
AGC 6.00 / 12.00 / 18.00 / 24.00 / 30.00 /
36.00 / 42.00 / 44.80
WHITE BAL ANTI CR
MANUAL LEVEL 012 ~ 031
PUSH LOCK
ATW SPEED 0 ~ 255
DELAY CNT 0 ~ 255
ATW FRAME x0.50 / x1.00 / x1.50 / x2.00
ENVIRONMENT INDOOR / OUTDOOR
11
Camera menu tree
SUB-MENU OPTIONS
AUTO HIGH
LUNINANCE
MODE AUTO IRIS /
SHUT+AUTO
IRIS
SHUTTER / AGC
BRIGHTNESS 0 ~ 255
LOW
LUMINANCE
MODE AGC / OFF
BRIGHTNESS x0.25 / x0.50 /
x0.75 / x1.00
MANUAL MODE SHUT + AGC
SHUTTER 1/50; 1/120; 1/250; 1/500; 1/1000;
1/2000; 1/4000; 1/10000
AGC 6.00 / 12.00 / 18.00 / 24.00 / 30.00 /
36.00 / 42.00 / 44.80
WHITE BAL ANTI CR
MANUAL LEVEL 012 ~ 031
PUSH LOCK
ATW SPEED 0 ~ 255
DELAY CNT 0 ~ 255
ATW FRAME x0.50 / x1.00 / x1.50 / x2.00
ENVIRONMENT INDOOR / OUTDOOR
12
SUB-MENU OPTIONS
WHITE BAL PUSH
USER1 /
USER2
B – GAIN /
R – GAIN
0 ~ 255
BACKLIGHT OFF / BLC / HLC
PICT ADJUST MIRROR OFF / ON
BRIGHTNESS /
CONTRAST /
SHARPNESS /
HUE / GAIN
0 ~ 255
ATR OFF
ON LUMINANCE LOW / MID / HIGH
CONTRAST LOW / MIDLOW / MID / MIDHIGH /
HIGH
PRIVACY OFF
ON AREA SEL 1/4; 2/4; 3/4; 4/4
TOP / BOTTOM 0 ~ 288
LEFT / RIGHT 0 ~ 370
COLOR 1 ~ 8
TRANSP 0.00 / 0.50 / 0.75 /
1.00
MOSAIC ON / OFF
12
SUB-MENU OPTIONS
WHITE BAL PUSH
USER1 /
USER2
B – GAIN /
R – GAIN
0 ~ 255
BACKLIGHT OFF / BLC / HLC
PICT ADJUST MIRROR OFF / ON
BRIGHTNESS /
CONTRAST /
SHARPNESS /
HUE / GAIN
0 ~ 255
ATR OFF
ON LUMINANCE LOW / MID / HIGH
CONTRAST LOW / MIDLOW / MID / MIDHIGH /
HIGH
PRIVACY OFF
ON AREA SEL 1/4; 2/4; 3/4; 4/4
TOP / BOTTOM 0 ~ 288
LEFT / RIGHT 0 ~ 370
COLOR 1 ~ 8
TRANSP 0.00 / 0.50 / 0.75 /
1.00
MOSAIC ON / OFF
13
SUB-MENU OPTIONS
DAY/NIGHT COLOR
B/W BURST ON / OFF
AUTO BURST ON / OFF
DELAY CNT 0 ~ 255
DAY-> NIGHT 0 ~ 255
NIGHT-> DAY 0 ~ 255
NR NR MODE Y/C; Y; C; OFF
Y LEVEL
C LEVEL
CAMERA ID OFF / ON
LANGUAGE ENGLISH / 日本語 / DEUTSCH / FRANCAIS / / PORTUGUÊS /
ESPAÑOL
CAMERA RESET
13
SUB-MENU OPTIONS
DAY/NIGHT COLOR
B/W BURST ON / OFF
AUTO BURST ON / OFF
DELAY CNT 0 ~ 255
DAY-> NIGHT 0 ~ 255
NIGHT-> DAY 0 ~ 255
NR NR MODE Y/C; Y; C; OFF
Y LEVEL
C LEVEL
CAMERA ID OFF / ON
LANGUAGE ENGLISH / 日本語 / DEUTSCH / FRANCAIS / / PORTUGUÊS /
ESPAÑOL
CAMERA RESET
Loading...