AVSL Stereo Twin PAR Bar Lighting Set User Manual

www.AVSL.com

Stereo Twin PAR Bar

LED PAR Bars with Foot Control

Item ref: 151.554UK

User Manual

Please read through this manual thoroughly before
use, any damage caused by misuse of the product
will not be covered by the warranty.

2 151.554UK User Manual

Safety Instructions

• Please keep this manual for future reference.

• Always make sure that you are connecting to the proper voltage, and that the line

voltage you are connecting to is not higher than that stated on the bottom of the
fixture.

• This product is intended for indoor use only. It must be connected to an earthed

mains outlet.

• To prevent risk of fire or shock, do not expose fixture to rain or moisture. Make

sure there are no flammable materials close to the unit while operating.

• The unit must be installed in a location with adequate ventilation, at least 20cm

from adjacent surfaces. Be sure that no ventilation slots are obstructed.

• Always disconnect from power source before servicing or replacing fuse and be

sure to replace with same fuse size and type.

• Maximum ambient temperature is 40°C. Do not operate the fixture at higher

temperatures.

• In the event of a serious operating problem, stop using the unit immediately.

Never try to repair the unit by yourself. Repairs carried out by unskilled people
can lead to damage or malfunction. Please contact the nearest authorised
technical assistance centre.

• Make sure the power cord is never crimped or damaged.

• Never disconnect the power cord by pulling or tugging on the cord.

• Avoid direct eye exposure to the light source while it is on.

Contents in the box

• PAR Bar x2

• Tripod stand x2

• Foot Controller

• Remote control

• Carry Case for Par Bar and Foot control

• Carry case for tripod x2

• Instruction Manual

• Power cable x2

• 10M DMX cable

• Hanging Bracket and Screw Set x4

3 151.554UK User Manual

Features

• Twin PAR Bar lighting set with 2x2x5pcs 10W Quad LEDs

• High output with 3255Lux at 2M when full on with one separate head

• Saturated wash effect without multicoloured shadows

• Foot controller with 10M cable and IR remote control

• Separate light head control with various built-in colour macros

• Easy setup and tear-down with tripod stand and carrying bags

Specification

• Power supply 220-240 Vac, 50/60Hz (IEC)

• Fuse rating 2A

• Power consumption 200W

• IP rating IP20

• Cooling Fan

• LED Type 10W RGBW 4in1 LED x 20pcs

• Colour Temp. 8000K

• Average life span 50,000 Hours

• Standard beam angle 25°

• Dimming 0-100%

• Luminance 3255Lux @2M per head

• Strobe 1-25 Hz

• Dimension

o

PAR bar 600x245x65mm

o

Stand Compact 140x110x1025

▪

Height extension 1140 – 1870mm

o

Foot Controller 420x155x38mm

o

Main Carry Case 660x300x220mm

• Weight

o

Overall 18Kg

o

Main Carrier with contents 12Kg

o

Stand in carrier 3.0Kg

4 151.554UK User Manual

o

Setup/Installation

This lightweight, versatile PAR bar system is prefect for mobile DJs and performers
who need their lighting to be quick to set up and easily transportable. 4 PAR Cans
are each loaded with 5 LEDs in red, green, blue and white for super smooth colour
blending.

1. Remove stands from the carrier and open the tripod legs onto the floor,

make sure it is on a stable footing.

2. Remove the PAR bars from the main carrier and attach them onto the

tripod stand.

3. Tighten the screw to secure the PAR bar.

4. Connect the Power cables on both units.

5. Setting the PAR BARs to Master and Slave (see PAR Bar mode settings.)

6. Connect the multi-core lead to the foot controller and the Master unit.

7. Connect the XLR cable (3 Pins) to the DMX OUT socket on the Master

unit and the DMX IN socket on the Slave unit.

8. Adjust height of the extension pole, insert safety pin and tighten the

locking screw.

9.

Hanging Brackets are included for permanent fitting on trusses (Truss attachments
are not included) or screw to the ceilings. Attach bracket with screw onto the ends of
the PAR bar as shown: -