AVSL SINGLE COLOUR LED TAPE User Manual
SINGLE COLOUR LED TAPE
Stock code
Voltage
Colour
Luminous flux
(Lumens per metre)
Light intensity per LED
(millicandelas)
156.705UK
12Vdc
Red
60lm/m
600mcd
156.706UK
12Vdc
Pink
120lm/m
1000mcd
156.708UK
12Vdc
Green
130lm/m
1200mcd
156.711UK
12Vdc
Blue
30lm/m
500mcd
156.714UK
12Vdc
Yellow
45lm/m
600mcd
156.717UK
12Vdc
White (6500K)
180lm/m
2400mcd
156.718UK
12Vdc
Warm white (2700K)
180lm/m
2400mcd
156.755UK
24Vdc
Red
60lm/m
600mcd
156.756UK
24Vdc
Pink
120lm/m
1000mcd
156.758UK
24Vdc
Green
130lm/m
1200mcd
156.761UK
24Vdc
Blue
30lm/m
500mcd
156.764UK
24Vdc
Yellow
45lm/m
600mcd
156.767UK
24Vdc
White (6500K)
180lm/m
2400mcd
156.768UK
24Vdc
Warm white (2700K)
180lm/m
2400mcd
Common Specifications
Number of LEDs
60/m
Beam angle
140°
Cut intervals
5cm
Reel length
5m
LED type
Epistar™ SMD3528
LED spacing
16mm
IP rating
IP65
Power consumption / metre
4.8W
Cross-section
10.5 x 2.55mm
Weight
210g
Installation Guide
Caution: Please read this guide carefully before installing Fluxia LED tape
Damage caused by incorrect application is not covered by the warranty
Fluxia single colour LED tape is supplied on 5m reels in either 12Vdc or 24Vdc voltages.
Tape length
5m
10m
15m
20m
25m
30m
35m
40m
Current for 12V tape
2A
4A
6A
8A
10A
12A
14A
16A
Current for 24V tape
1A
2A
3A
4A
5A
6A
7A
8A
Disposal: The “Crossed Wheelie Bin” symbol on the product means that the product is classed as Electrical or
Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life.
The goods must be disposed of according to your local council guidelines.
Installation should be carried out by competent electrical installers, observing the relevant electrical safety procedures.
Fluxia single colour LED tape has a self-adhesive backing to allow it to be easily attached to a clean, non-porous surface.
Where less than 5m of tape is needed, there are solder points as shown below, where the tape may be cut to size. These
cut points will be at 5cm intervals for 12V tape and 10cm intervals for 24V tape. In order to re-connect to another length
of tape after cutting, strip away the epoxy coating at the solder points and solder a wire from “+” to “+” and a wire from
“-” to “-” as shown below. Some accessories are supplied with the tape reel for this purpose. In order to retain weatherproofing, it is advised to seal the cuts and joints with silicone glue.
Each 5m reel of single colour LED tape is fitted with a 2.1mm DC jack socket for power input for easy connection to a
power supply. This connector may be removed and stripped for bare wire connection if a 2.1mm jack is not fitted to the
power supply.
If the power supply has enough capacity to power more than one reel, another reel can be connected to the end of the
first reel via the 2.1mm DC jack plug.
For 12V single colour LED tape, it is recommended to link no more than 15m of tape in sequence. For 24V versions, up to
30m can be linked in this way. Using a separate wire to loop “+” and “-” back to the power supply will help to avoid
dimming at the far end through voltage drop. To connect beyond these lengths, a parallel wire must be run from the
power supply to the further reels of tape.
It is imperative that the power supply should have higher than the rated capacity in Amps (A) for the current required to
power the length(s) of LED tape installed. Please see the table below for reference.
Please visit www.avsl.com to select from our range of 12Vdc and 24Vdc power supplies that are suitable for powering
Fluxia LED tapes.
Errors and omissions excepted.
Copyright © 2014. AVSL Group Ltd.
Single Colour LED Tape Installation Guide
Loading...