Avsl LED-NCF4-40W5K, LED-NCF4-20W5K, LED-NCF5-30W5K, LED-NCF5-60W5K, LED-NCF4-20W5KEM User Manual

User Manual

LED-NCF 4ft/5ft

IP65 Non-Corrosive LED Battens

Item ref: 520.850UK, 520.853UK, 520.856UK, 520.589UK, 520.900UK, 520.903UK,

520.906UK, 520.909UK

User Manual

A durable IP65 LED batten, ideal for use in environments where water and dust
ingress could be an issue such as industrial areas, garages and workshops.

• Available in two lengths (4 feet and 5 feet)

• Emergency Maintained (3hrs) versions available

• Strong polycarbonate constructed case rated to IP65

• Colour Temperature- 5000K

• Lamp Life- >30,000 hours

• Beam Angle- 120°

This is a mains powered product. It is designed to be installed by suitably qualified personnel
only and in accordance with the applicable building and electrical regulations. Before
installation or maintenance, the electrical supply to the product must be isolated.

If installation advice or accessories are required, please also contact your local distributor.
When reporting a suspected fault or seeking installation support, the problem is likely to be
resolved most quickly if you have full product details to-hand, as well as details of when and
where it was purchased.

Luminaires fitted with electronic drivers are exempt from insulation resistance tests, as this
may cause irreparable damage to the ballast.

Product Specifications:

Model Number

Product Code

Length

Wattage

Lumens

Emergency

LED-NCF4-20W5K

520.850UK

4ft

20W

2000lm

No

LED-NCF4-40W5K

520.853UK

4ft

40W

4000lm

No

LED-NCF5-30W5K

520.856UK

5ft

30W

3000lm

No

LED-NCF5-60W5K

520.859UK

5ft

60W

6000lm

No

LED-NCF4-20W5KEM

520.900UK

4ft

20W

2000lm

Yes

LED-NCF4-40W5KEM

520.903UK

4ft

40W

4000lm

Yes

LED-NCF5-30W5KEM

520.906UK

5ft

30W

3000lm

Yes

LED-NCF5-60W5KEM

520.909UK

5ft

60W

6000lm

Yes

User Manual

Luminaire Installation:

1. Undo the clips on each side and hinge open the controller.

2. Fix the base. The base can be fixed via the following methods; once chosen, prepare
the ceiling/mounting points ensuring the fixing surface/mechanism is enough to
support the luminaire weight and its application:

• Surface fixing: Mount the two stainless steel surface mount fixing clips provided to
the ceiling at the specified fixing centres. Offer the base up to the clips and push to
snap fit.

• Chain or Wire suspension: Mount the two stainless steel surface mount fixing clips
to the base. Then add a V hook (provided in the pack) to each of the surface mount
clips. This will then provide connection points for chain or wire suspension at the
specified fixing centres.

• Conduit Suspension: The base comes with specific 20mm diameter drill out points.
These points are reinforced for conduit suspension purposes. Care must be taken to
drill a clean hole and not to remove any of the reinforced wall around the hole.

3. Route the mains supply cable into the base. This can be via the pre-drilled hole with
compression gland at one end, or via drilling a hole at one of the allocated positions.
It is the installer’s responsibility to ensure the IP65 rating is maintained.

4. Refit the gear tray on to the retaining straps via the snap hooks.

5. Route the mains supply cable to the terminal block and terminate, ensuring correct
termination is observed.

6. Fully locate the gear tray into the base by aligning the slots with the clips in the base
and securing.

7. Fit the controller by hinging back into position & securing using the snap-fit clips.

8. If vandal resistance is required, fit the small screws provided into each clip.

9. Reconnect power supply & check for correct operation.

Errors and omissions excepted.

Copyright© 2019. AVSL Group Ltd.