Page 1
LED DUOBEAM
Item ref: 151.602UK
Dual Moonflower Effect
User Manual
Page 2
Introduction
Display
Mode
Function
DMX512
Address setting A001 – A512
Slave mode
Receives control via XLR from another LED DUOBEAM
Auto programme mode
Auto run sequence to internal programme
: sound activated mode 1
Sound-to-light with auto run when no sound present
: sound activated mode 2
Sound-to-light with LEDs off when no sound present
Thank you for choosing the QTX LED DUOBEAM quad colour dual LED barrel light as part of your effect
lighting rig. Please read these instructions in full to gain the best results from this item and avoid damage
through misuse.
Unpacking
Your LED DUOBEAM should reach you in good condition and be supplied with appropriate mains lead(s)
and mounting bracket. If there are any signs of damage or items missing from the packaging, contact
your dealer immediately.
Warning
To prevent risk of fire or electric shock, do not expose any components to rain or moisture.
If liquids are spilled on the housing, disconnect mains and allow unit to dry out & have checked by
qualified personnel before further use. Avoid any impact or extreme pressure to the housing.
No user serviceable parts inside – Do not open the case – refer all servicing to qualified service personnel.
Safety
Check for correct voltage and condition of IEC lead before connecting to power outlet
Ensure DMX leads are good condition with no short connections or damaged plugs
Placement
Mount the unit to a lighting stand or ceiling using the adjustable bracket included
If the unit is mounted at height, a drop cable should be attached for safety
If free-standing, ensure that the unit is sited on a stable, non-slip surface.
Ensure adequate access to controls and connections
Cleaning
Use a soft dry or slightly damp to clean the cabinet. Do not use strong solvents for cleaning the unit
Setting up
Install the LED DUOBEAM so that the front panel is facing the area to be lighted.
Experiment with positioning to get the best coverage from the mirrored beams.
For DMX or master/slave control, link control signals with XLR leads from DMX out to DMX in connectors.
Connect mains using an appropriate IEC lead to the mains inlet.
Operation
The LED DUOBEAM can be operated in either DMX or standalone auto and sound activated modes.
For auto or sound-activated modes, you can select 1 unit to be master with XLR connection to a slave.
Select the mode to be used via the 4 button panel with digital display as shown below.
151.602UK User Manual
Page 3
Rear Panel
1. Microphone sensitivity control
5. Cooling fan vent
2. Sound activation microphone
6. Digital display
3. IEC mains inlet & fuse holder
4. Mode/programming buttons
7. DMX input XLR
8. DMX output XLR
DMX Channel
Mode
Value
Function
Channel 1
Mode setting
000-050
Blackout
051-100
Auto mode
101-150
Sound activated - auto when no sound present
151-200
Sound activated - blackout when no sound present
200-255
DMX512
Channel 2
Y-axis (barrel)
000
Y-axis rotate clockwise
001-254
Y-axis position setting
255
Y-axis rotate anticlockwise
Channel 3
Y-axis speed
000-255
Y-axis speed adjustment - 000=fast, 255=slow
Channel 4
X-axis (yoke)
000-255
X-axis position setting 0-180°
Channel 5
X-axis speed
000-255
X-axis speed adjustment - 000=fast, 255=slow
Channel 6
Left head: W
000-255
Left head white output
Channel 7
Left head: B
000-255
Left head blue output
Channel 8
Left head: G
000-255
Left head green output
Channel 9
Left head: R
000-255
Left head red output
Channel 10
Right head: W
000-255
Right head white output
Channel 11
Right head: B
000-255
Right head blue output
Channel 12
Right head: G
000-255
Right head green output
Channel 13
Right head: R
000-255
Right head red output
151.604UK User Manual
Page 4
Power supply
100-240Vac 50/60Hz (IEC)
Power consumption
30W
Operating modes
Auto, Sound activated, Master/Slave, DMX
DMX operation
DMX512: 13-channel
LED sources
2 x RGBW 10W CREE LED
Connection
DMX in/out (XLR), Mains inlet (IEC)
Dimensions
325 x 159 x 165mm (inc. bracket)
Weight
3.17kg
No power
Check mains voltage is correct and outlet is switched on
Check IEC lead and mains fuse (if fuse continually blows, refer to your dealer)
No light output
Check rear panel mode settings (SOU2 with no sound, slave mode, DMX etc.)
Check DMX settings from controller (RGBW outputs for each head)
No sound activation
Check that sound activated mode is selected and not set to slave
Check rotary control for microphone sound sensitivity is not fully down (left)
Disconnect any DMX input if sound activated mode is to be used
Unresponsive to DMX
Check DMX connection and leads
Check that DMX mode is enabled
Check the DMX start address is set correctly
No barrel movement
Check DMX X-axis and Y-axis settings
Check that barrel is not stuck or blocked by foreign object
Overheating/cutting out
Ensure that the unit is not too close to a heat source
Ensure that the cooling vent on the rear panel is clear and not covered
Specifications
Troubleshooting
Errors and omissions excepted.
Copyright© 2013. AVSL Goup Ltd
151.604UK User Manual
Loading...