Page 1
FH-700
Item ref: 160.458UK
Fog/Haze Machine
User Manual
Page 2
INTRODUCTION:
FH-700 Fog/Haze Effect Machine
This mini effects unit produces both a fog and haze. The flow rate and internal rotary
fan can be adjusted to produce either thick fog effects or light haze depending on
your requirements. Supplied with a handheld timer remote control, making it suitable
for a wide variety of applications such as nightclubs, laser shows mobile DJs and
theatres.
6,000 Cu Ft (170m³) per minute (approx.)
Anti-jamming pipe technology
Intelligent microcomputer keeps the temperature high
Removable tank for easy maintenance
Robust metal housing
Timer output control included
High grade haze fluid should be used with this machine (we recommend
160.590 or 160.591)
160.458UK User Manual
Page 3
FZ-700 Unit x 1pc
User’s Guide x 1pc
Power Cord x 1pc
Remote Control x 1pc
QTX Ref Code
Description
Size
Results
160.590UK
High quality
professional Haze fluid
1 Litre
High quality ultra
fine mist
160.591UK
5 Litre
PACKAGE CONTENTS:
Please check the contents to ensure that the product has been received in good
condition.
If you find any accessory is missing or the machine has arrived with any problems,
please contact your local dealer at once. Do not try to fix this item yourself or you
will lose the warranty. Please keep the original package and invoice for any possible
replacement or returned demand.
RECOMMENDED FLUID:
For the FH-700 haze machine we strongly recommend the following fluid which has
been specifically formulated to perform best with any heater based haze machines.
160.458UK User Manual
Page 4
SETUP:
1. Unpack the FH-700 unit.
2. Unscrew the top cap of the tank and remove to fill with the recommended
haze fluid.
3. Replace the bottle and screw the cap securely ensuring the pipe is fed down to
the bottom of the bottle so a consistent flow of fluid is supplied to the
machine.
4. Connect the remote control.
5. Connect the IEC mains plug and power up.
6. Heat up time is usually between 5-6 minutes. Please ensure no button is
pressed during the heat up time. When the machine is ready the LED light on
the remote control will illuminate.
7. Turn the output to max and press the green button on the remote control for
5 seconds so the fluid has a chance to flow through the heater block making it
ready to use.
8. After this adjust the fan speed on the unit and the output on the remote
control to find the level you desire. It is recommended to produce haze/fog
with small pauses in between so that the temperature is maintained and the
thermostat doesn’t switch off.
CAUTION! TO PREVENT MORTAL ELECTRICAL RISK AND LONG LIFE OPERATION:
For your safety, please kindly pay attention to all of the warnings listed below:
Always plug in the power plug last and disconnect from the mains when the
device is not in use or before cleaning.
Do not install and operate the device in rain or extreme heat, moisture or dusty
environments.
This device is for indoor use only and in a dry environment.
Do not switch on immediately but wait until it reaches to room temperature if
the device has been exposed to drastic temperature fluctuations.
Do not shake the device and avoid brute force when installing or operating.
Do not use the device during thunderstorms and please disconnect the power.
Do not use solvents or aggressive detergent to clean the device. Use a soft and
clean cloth.
Do not modify the device or the connected power cord without authorisation.
160.458UK User Manual
Page 5
Wire
Connection
International signal
Brown
Live
L
Blue
Neutral
N
Yellow /Cyan
Earth
CONNECT WITH POWER SUPPLY – THE GROUND WIRE MUST BE CONNECTED:
Use the plug to connect to the main power supply as follows:
QUICK TROUBLE SHOOTING
If the unit is not functioning properly
Check if main power is on.
Check the fuse hasn’t blown.
Check the unit isn’t in DMX mode.
Check there is fluid in the tank and the pipe is pushed down to the bottom of the bottle
If there is blockage use distilled water or haze machine cleaning fluid
REPLACING FUSE
Disconnect from the main power supply first. Then remove the fuse holder above the IEC
Socket to reveal the fuse. Replace the correct fuse rating as stated on lighting or user guide.
Then, lock the fuse holder cover back into place.
GENERAL MAINTENANCE
To maintain optimum performance and minimize wear, the item should be cleaned frequently.
Usage and environment are contributing factors in determining frequency. As a general rule,
fixtures should be cleaned after use to avoid dust build-up and blockages, which can result in
poor performances, overheating and breakages. Be sure to power off fixture before conducting
maintenance.
Unplug fixture from power. Use a vacuum or air compressor and a soft brush to remove dust
collected on external vents and internal components. Clean the external case when the fixture
is cold with a dry cloth or tissue, and drag dirt and grime to the outside case.
160.458UK User Manual
Page 6
LAYOUT FH-700:
1.
Carry handle
2.
Haze nozzle output
3.
Bottle cap and feed tube
4.
Removable bottle
5.
Fill level indication
160.458UK User Manual
Page 7
REAR PANEL FH-700:
1.
Power ON/OFF
2.
Power IN (Use IEC lead provided)
3.
Controller connection
4.
Fan Speed*
*Fan Speed control: The FH-700 features a manually adjustable fan to control the distance the
fog / haze can be dispersed.
Generally low speeds are suitable for small areas where as higher speeds are for larger areas.
160.458UK User Manual
Page 8
TIMER CONTROLLER
1. Timer on/off button
2. Continuous output
3. Manual override button
4. Timer LED indicator (Illuminated Yellow when timer active)
5. Manual ready indicator (Illuminates Green when ready)
6. Power indicator (Illuminates red when power is on)
7. Adjust the output level between 0-100%. Generally 0-30% is haze effect and 31-100%
is Fog level output.
NOTE:
The below controls are only used when in timer mode
8. Adjust the interval gap between each release (between 0 – 30 Min approximately)
9. Adjust the duration the Haze / Haze is released at each interval (between 0 – 15
seconds approximately)
For best results select “continuous” and adjust output to achieve desired effect, note it
can take around 30 seconds for the machine to produce the correct output.
160.458UK User Manual
Page 9
160.458UK User Manual
Page 10
TECHNICAL SPECIFICATION
Power supply
230Vac, 50Hz
Fuse
F5A
Power
700W
Re-heat time
5-6 min (approx.)
Haze Output
6,000 Cu Ft (170m³) per minute
Tank capacity
2.5 Litres
Dimensions
400 x 215 x 210mm
Weight
5.3kg
DISPOSAL:
Please disposal of the unserviceable device according to the current statutory requirements.
Errors and omissions excepted.
Copyright© 2012. AVSL Goup Ltd
Loading...