AVS Pixim212VIR User Manual

VANDAL-PROOF & WATERPROOF

WDR IR D&N 3-AXIS

DOME CAMERA

Pixim212VIR

MANUAL

◐PRECAUTION

◐FEATURES

1. You can install the camera indoors or outdoors.

2. Choose an ideal location for the camera, since a camera unit must
be protected against vibration.

3. Be careful not to scratch the camera unit, especially lens or dome
cover.

4. Use the camera within the temperature(14℉ ~ 122℉).

5. Avoid any direct sun light toward the lens.

6. Use the ACadaptor 12V DC or 24V AC, 1A.

1. IP67(Waterproof)

2. Durable MATERIAL : Body - Aluminum, Dome - Polycarbonate

3. This camera is incredibly flexible to install with its 3-axis camera

construction, which makes the camera ceiling, wall or slope
mountable.

4. 100ft range visible in total darkness with 24pcs of IR LEDs.

5. Mechanical filter exchange(True Day & Night),built-in WDR function.

6. Adopted DNR technology, It reduces noise efficiently in low light

condition.

7. Supreme Resolution.(690 TV-Line)

8. Multi-language full OSD support.

If theproduct is to beput out of operation definitively,
take it to a local recycling plant for a disposal which
is not harmful to the environment.

2. Pipe application

3. Camera angle adjustment :

(1)Remove the screw for fixing a cable on the bottom ofthe base.
(2) Open theDOME COVER.
(3) Remove the TAP COVER and place the cables there.
(4) After distributingcables, use the TEPLON tape to wipe the pipe.
(5) Combine the pipe to the base.

: Grasp the disk of camera and then adjust

direction to theright or left(-160 ~ 190 )

: Grasp the LED cover of camera and then

adjust direction to the up or down(6 ~ 90 )

: Grasp the camera holder and then rotate

(-178 ~ 178 )

<Caution> If you don't wipe TEFLON tape on pipe, itmight cause troubles on

water-resistant.

(1) Pan adjustment

(2) Tilt adjustment

(3) Roll adjustment

˚ ˚

˚ ˚

˚ ˚

◐ DIMENSION

<Caution> If you try toadjust the camera out of limited angle, it might cause

troubles and damageto camera.

◐ HOW TO INSTALL

1. Camera installation

<Ceiling mount>

<Wall mount>

(1) Fix the cameraset with the supplied screws on ceiling or wall mount.

If you don't use supplied screws, the camera may fall off.

(2) Please refer to '3. Camera angle adjustment' regard ing adjust

camera angle.

(3) Lens adjustment

After opening the LEDc over,
① By turning the "Tele-Wide" knob,

you can access a range of focal
lengths within specified limits.

② Since then, by turning the "Near-Far"

knob, you can set the focus toward
the wanted object.

(4) Re-assemble the camera.

SCREWTp1 4X253EA

MOUNT HOLE PLATE(STICKER)

Ø3.5

Ø30

SCREW Tp14X25 3EA

MOUNT HOLE PLATE(STICKER)

Ø3.5 Ø30

Put asticker on theceiling andmake holes
accordingto the spots markedon a sticker

Put asticker on the wall and make holes
accordingto the spots markedon a st icker

LED COVER

DISK

ROTATION

U

D

R

L

CAMERAHOLDER

Ø100

Ø150.5 Ø129

CABLE

PIPE

TEFLONTAPE

TAP COVER

CABLEFIXING SCREW

DOMECOVER

◐SPECIFICATION

①ENTER :
ㆍ

②UP, ③DOWN :
④L EFT, ⑤ RIGHT :

⑥EXT-VIDEO:

⑦LED :

Push the lever : Used to access the menu and confirm selection.

ㆍPushthe lever for one second :Open themenu or close the menu.

Used to return to previous menu from the motion detection or
privacym askse ttingsection.

Used to move the cursor to up or down.

Used to move the cursor to left or right and

change the value.

Extra video output terminal for installation. Plug your

test monitor in hear. The cable is option.

LED level adjust.

<Caution>In case of operating "LED", don't put stress excessively.

◐FUNCTION SETTING

1. How to use the jog lever

7

6

MIN

Model No.

Image Sensor

Effective Pixel

Resolution

TV Type

Sync. Type

ScanningSystem

Video Output

Gamma Characteristic

Min. Illumination

S/N Ratio

SDNR

Backlight

Day & Night

LED Output

Gain Control

Sense Up

Test Illumination

PowerSupply

CurrentConsumption

Lens

Operation Temp.

Preservation Temp.

Dimension

Weight

White Balance

Reverse Polarity Protection

Pixim212VIR

1/3" PIXIM DPSSENSOR - SEAWOLF

758(H)x 540(V) Pixel

690 TV- Line

Progressive scan

1.0 Vp-p(Sync.Negative) Termination 75Ω±10%

γ

= 0.45(Selectable)

ATW / AWC /MANUAL(2,000~ 11,000 )

0.005 64 100ft

More 50 dB(AGCOFF)

ON

WDR / BLC/ OFF

True D&N(AUTO /COLOR / BW)

Leveladjustable

AUTO/ MANUAL

Max. X64(X2,X 4, X8, X16,X32, 64)

Average testilluminance by front view

: :

Yes

f =2.8 ~ 12mm Vari focalauto irislens

14℉ ~ 122℉

-4℉ ~140℉

Ø150.5 x 95.6(H)mm

Approx.1.76 lbs

NTSC

Internal/ External

Lux(Senseup X ), 0Lux(LEDs ON,Max. )

IR LED24pcs( )

X

Regulated 12V DC or24V AC

Max. 500mA(at12V DC) LED ON,Max. 510mA(at24V AC) LED ON

CUSTOM

INDOOR

WINDOW

OUTDOOR

LOW

NORMAL

MEDIUM

HIGH

OFF

ON

CUSTOM --

LOW(24)

MEDIUM(30)

HIGH(36)

OFF

AUTO- -

MANUAL- -

OFF

CRR

CRR2

R/B- -

KELVIN- -

INPUTDELAY
(Sec)

25~ 45~ 100

MIN ~MAX

-8 ~ 0 ~ 8

OFF

HORIZ

VERT

BOTH

OFF

ON

Lens type selection
(Fixedi ris lens or Vari-focalauto iris lens)

User settingvalue

For indoor

Maximizing WDR function

For outdoor

Althoughthe subject had a brightlight behind
of it, you can see the subject clearly as well
as background

Determines that useBLC(BackLight Compen­sation)functionor not

AGC levelselectable
(Custom- - Limit : 60)

No use sense-upmode

Use sense-up mode automatically in low
illumination(Limit : 2X~ 64X)

Sense-uplevel selectable between x2~ x64

Optimized mode forflicker(If user choose CRR2
mode,AWC modeis notavailable on the White
Balancemenu)

Balancesthe colorautomaticallydependingon
thesource of light from 2,000 ~ 11,000

Move the camera lens toward to white paper
then press the enter button to find the optimal
whitebalancefor currentenvironment(Usercan
notuse this mode when Flickerless is CRR2)

Adjustthe Redo r Blue values to shift thecolor
of the object

Adjustcolor temperature

The camera automatically detects lighting
conditionand selectsthe modeaccordingly

The picture is always displayed inColor

The picture is always displayed in Black and
white

Change the GAMMA ofthe screen
(Default: 45)

Change the sharpness of the screen
(Default: Max)

Change the color gain of the screen
(Default: 0)

Normal image(Noimage inversion)

Set ahorizontal image inversion

Set avertical image inversion

Set horizontal and verticalimage inversion

Normal image(NoZoom)

Max 4x digitalzoom available

PAN, TILT : Zoomed in image can be movedto
horizontal andvertical

DC

MANUAL

PRESETS

WDR

BLC

AGC

SENSE-UP

FLICKERLESS

ATW

AWC

MANUAL

AUTO

COLOR

B/W

GAMMA

SHARPNESS

COLOR GAIN

FLIP

ZOOM

2.

OSD menu structure

OSD Menu Select Menu SummarySub Menu

LENS SELECT

EXPOSURE..

WHITE
BALANCE

DAY&NIGHT

*Preset mode for common application to speed up installation

Determines that use the SENSE-UP function orn ot and
SENSE-UPlevel selectable

IMAGE
ADJUST..

3. When using control device through RS-485 protocol

(1) ENTER

(2) Up Down

(3) Left Right

(4) IRIS CLOSE KEY

ㆍPush the IRIS OPEN key : Used to access the menu and confirm

selection.

ㆍPush the IRIS OPENkey for one second : Open or closethe menu

and use it to escape the setup in case of setting Privacy Zone or
Motion detection Zone.

ㆍ
ㆍMoveJoystick to up/down or push the arrow key(↑,↓)
ㆍUsedto move the cursor toup or down to choose the menu.

ㆍ
ㆍMoveJoystick to left/right or push the arrow key(← , →)
ㆍUsedto move the cursor toleft or right to change the value.

ㆍUse it to move out to previous menu.
ㆍTo escape the setupwhen setting the Privacy Zone or Motion Zone.

<Caution> Do notuse the menu key onthe controller.

ㆍThe ' ' or'- - ' icon appeared with desiredfunction, press theset buttonto movesub menu.
ㆍThe '- --' icon appeared with function that isunavailable according to function setting.

* User can controlthe menuby using PELCO-D, 2,400bpsonly.

No use motiondetection function

Select motion detection areaup to 4area

- Adjust position& sizeof motiondetectionarea

- Pressthe enter buttonto move intothe motion
areasetting section, whenever you press the
enterbutton,the mask color is changed.

- When the mask color iswhite you can set the
position of mask by up, down, left and right
button.

- When the mask color is green and red you
canadjust the sizeby 4buttons.

- Press the enter button for a few second to

escape.

No use privacymask function

- Allowyou to maskcertainareas of thescreen,
support12 privacy zone

- Press theset button to move into the privacy
masksettingsection,wheneveryou pressthe
setbutton,the mask color ischanged.

- When the mask color iswhite(orblack or red)
youcan setthe position of mask byup, down,
leftand rightbutton.

- When the mask color is blue, youcan adjust
thesize by4 buttons.

- Press the enter button for a few second to

escape.

Select mask color(White, Black,Red)

ID setting for RS-485communication(1~255)

Displaythe cameraID on the screen

Change the camera ID

Select the position todisplay theID onthescreen

InternalSync with 12V DC power

ExternalSync with 24V AC power
(Dual power only)

Phase contollable at 24V AC input(L/L mode)

AREA SELECT

AREA 1~ 4

MASK 1 ~ 12

MASK COLOR

CAMERA #

ID DISPLAY

CAMERA ID

ID POSITION

V-PHASE

OFF

ON…

OFF

ON- -

RS-485
SETUP*

INT

L.L

CAMERA ID
SETUP

PRIVACY

MOTION

SYNC

FUNCTION
SETUP..

※All specification is subject tochange without notice to improvethe quality.

3B25201B