Page 1
3-AXIS WDR SUPREME RESOLUTION
DAY & NIGHT IR DOME CAMERA
Pixim212DIR
MANUAL
◐PRECAUTION
◐FEATURES
◐HOW TO INSTALL
1. Do not install the camera outdoors.
2. Choose a n ideal location for the camera, since a camera unit must
be protected against moisture and vibration.
3.Be careful not to scratchthe camera unit, especiallylens or dome cover.
4. Use the camera within the temperature(14℉ ~ 122℉).
5. Handle with care. Dropping it can cause serious damage to the
camera.
6. Avoid any direct sun light toward the lens.
7. Use the AC adaptor 1 2V DC, 1A regulated.
Dual voltage product can use 24V AC adaptor.(option)
1.This camera is incrediblyflexibleto install with its 3-axis camera construction, whichmakes the cameraceiling, wall or slope mountable.
2. 100ft range visible in total darkness with 24pcs of IR LEDs.
3. Mechanicalfilter exchange(True Day & Night), built-in WDR function.
4. Supreme Resolution.(690 T V-Line)
1. Opening the dome : Pushing the latch button.(Remove the
protection sheet after installing.)
4. Camera angle adjustment :
(1) Pan adjustment
(2) Tilt adjustment
(3) Roll adjustment
: Grasp the disk of camera and then adjust
direction to the right or left(-180 ~ 180 )
: Grasp the LED cover of camera and then
adjust direction to the up or down(6 ~ 90 )
: Grasp the camera holder and then rotate
(-178 ~ 178 )
˚ ˚
˚ ˚
˚ ˚
◐ DIMENSION
◐ ASSEMBLY
<Caution> If you try toadjust the camera out of limited angle, it might cause
troubles and damage to camera.
2. Removing the dome
3. Camera installation::
Lift the dome. When you push the latch
button, it is unlocked and you can lift the dome.
(1) Fix thecamera set with the supplied screws on ceiling or wall mount.
If you d on't use supplied screws, the came ra may fall off.
(2) Please refer to '4. Camera angle adjustment' regarding adjust
camera angle.
(3) Lens adjustment(Vari-focal Lens only)
After opening the LEDcover,
① By turning the "Tele-Wide" knob,
you can access a range of focal
lengths within specified limits.
② Since then, by turning the "Near-Far"
knob, you can set the focus toward
the wanted object.
(4) Re-assemble the camera.
<Ceiling m ount>
<Wall mount>
SCREW TP1 3.5X20 2EA
SCREW TP13.5X20 2EA
ROTATION
U
D
R
L
LED COVER
DISK
CAMERA HOLDER
If the product is to be put out ofoperation definitively,
take it to a local recycling plant fo r a disposal which
is not harmful to the environment.
Ø100
Ø130.8
Ø109
PROTECTIONS HEET
LATCH BUTTON
DOME COVER
LED COVER
SCREW
CAMERA MODULE
SCREW
CABLE
DISK
BASE
CONTROL PCB
PUSH BUTTON
HARNESS
SCREW
DUAL POWER PCB
Page 2
CUSTOM
INDOOR
WINDOW
OUTDOOR
LOW
NORMAL
MEDIUM
HIGH
OFF
ON
CUSTOM --
LOW(24)
MEDIUM(30)
HIGH(36)
OFF
AUTO- -
MANUAL- -
OFF
CRR
CRR2
R/B- -
KELVIN- -
INPUTDELAY
(Sec)
25~ 45~ 100
MIN ~MAX
-8 ~ 0 ~ 8
OFF
HORIZ
VERT
BOTH
OFF
ON
Lens type selection
(Fixedi ris lens orVari-focal autoiris lens)
User settingvalue
For indoor
Maximizing WDRfunction
For outdoor
Althoughthe subject had a bright light behind
of it, you can see the subject clearly as well
as background
Determines that useBLC(Back LightCompensation)functionor not
AGC levelselectable
(CUSTOM- - LIMIT :60)
No use sense-up mode
Use sense-up mode automatically in low
illumination(Limit: 2X ~ 64X)
Sense-uplevel selectable betweenx2 ~ x64
Optimized mode forflicker(Ifuser choose CRR2
mode,AWC modeis notavailable on the White
Balancemenu)
Balancesthe colorautomaticallydependingo n
thesource of lightfrom 2,000 ~ 11,000
Move the camera lens toward to white paper
then press the enter button to find the optimal
whitebalancefor currentenvironment(Usercan
notuse this modewhen Flickerlessis CRR2)
Adjustthe Redo r Blue values toshift the color
of the object
Adjustcolor temperature
The camera automatically detects lighting
conditionand selectsthe modeaccordingly
The pictureis always displayedin Color
The picture is always displayed in Black and
white
Change the GAMMA ofthe screen
(Default: 45)
Change the sharpness of the screen
(Default: Max)
Change the color gain ofthe screen
(Default: 0)
Normal image(Noimage inversion)
Set ahorizontal image inversion
Set avertical image inversion
Set horizontaland verticalimage inversion
Normal image(NoZoom)
Max 4x digital zoom available
PAN, TILT : Zoomed in imagecan be movedto
horizontal and vertical
◐SPECIFICATION
3B15575B
※All specificationis subject to change withoutnotice to improve the quality.
①ENTER :
ㆍ
②UP, ③DOWN :
④L EFT, ⑤ RIGHT :
⑥EXT-VIDEO:
⑦LED :
Push the lever : Used to access the menu and confirm selection.
ㆍPushthe lever for one second : Open the menu or close the menu.
Used to return to previous menu from the motion detection or
privacym asksettingse ction.
Used to move the cursor to up or down.
Used to move the cursor to left or right and
change the value.
Extra video output terminal for installation. Plug your
test monitor in hear. The cable is option.
LED level adjust.
<Caution>In case of operating "LED", don't put stress excessively.
DC
MANUAL
PRESETS
WDR
BLC
AGC
SENSE-UP
FLICKERLESS
ATW
AWC
MANUAL
AUTO
COLOR
B/W
GAMMA
SHARPNESS
COLOR GAIN
FLIP
ZOOM
2.
OSD menu structure
OSD Menu Select Menu SummarySub Menu
LENS SELECT
EXPOSURE…
WHITE
BALANCE
DAY&NIGHT
IMAGE
ADJUST…
◐FUNCTION SETTING
1. How to use the jog lever
*Preset mode for common application to speed up installation
Determines thatuse the SENSE-UPfunction ornot and
SENSE-UPlevel selectable
2
LED
MIN
3
54
1
7
6
No use motion detection function
Select motion detectionarea up to 4area
- Adjust position& sizeof motion detection area
- Pressthe enterbutton to moveinto the motion
areasetting section,wheneveryou press the
enterbutton,the mask coloris changed.
- When the mask coloris white you can set the
position of mask by up, down, left and right
button.
- When the mask color is green and red you
canadjust thesize by 4buttons.
- Press the enter button for a few second to
escape.
No use privacy maskfunction
- Allowyou to maskcertain areasof thescreen,
support12 privacy zone
- Press the set button tomove intothe privacy
masksettingsection,wheneveryou pressthe
setbutton,the mask coloris changed.
- When the mask color is white(or black or
RED) you can set the positionof maskby up,
down,left andright button.
- When themask coloris blue,you can adjust
thesize by 4 buttons.
- Press thesetbuttonfora few secondto escape.
Select mask color(WHITE,BLACK, RED)
ID setting for RS-485 communication(1~255)
Displaythe cameraID on the screen
Change the camera ID
Select theposition to displaythe IDon thescreen
InternalSync with 12V DC power
ExternalSync with 24V AC power
(Dual power only)
Phase contollableat 24V AC input(L/L mode)
AREA SELECT
AREA 1~ 4
MASK 1~12
MASK COLOR
CAMERA #
ID DISPLAY
CAMERA ID
ID POSITION
V-PHASE
OFF
ON…
OFF
ON- -
RS-485
SETUP*
INT
L.L
CAMERA ID
SETUP
3. When using control device through RS-485 protocol(option)
(1) ENTER
(2) Up Down
(3) Left Right
(4) IRIS CLOSE KEY
ㆍPush the IRIS OPEN key : Used to access t he menu and confirm
selection.
ㆍPush the IRISO PEN key for one second : Open or close the menu
and use it to escape the setup in case of setting Privacy Zone or
Motion detection Zone.
ㆍ
ㆍMoveJoystick to up/down or push the arrow key(↑,↓)
ㆍUsedto move the cursor to up or down to choose the menu.
ㆍ
ㆍMoveJoystick to left/right or p ush the arrow key(← , →)
ㆍUsedto move the cursor to left or right to changethe value.
ㆍUse it to move out to previous menu.
ㆍTo escape the setup when setting the Privacy Zone or Motion Zone.
<Caution> Do not use the menu key on the controller.
PRIVACY
MOTION
SYNC
ㆍThe ' ' or'- - 'icon appeared with desired function,press the set button to move sub menu.
ㆍThe '- --' icon appearedwith functionthat is unavailable according to function setting.
* User cancontrol themenu by using PELCO-D,2,400bps only.
FUNCTION
SETUP..
Model No.
Image Sensor
Effective Pixel
Resolution
TV Type
Sync. Type
ScanningSystem
Video Output
Gamma Characteristic
Min. Illumination
S/N Ratio
SDNR
Backlight
Day & Night
LED Output
Gain Control
Sense Up
Test Illumination
PowerSupply
CurrentConsumption
Lens
Operation Temp.
Preservation Temp.
Dimension
Weight
White Balance
Reverse Polarity Protection
Pixim212DIR
1/3" PIXIM DPS SENSOR -SEAWOLF
758(H) X 540(V) PIXEL
690 TV- Line
Progressive scan
1.0 Vp-p(Sync. Negative)Termination 75Ω±10%
γ
= 0.45(Selectable)
ATW / AWC/ MANUAL(2,000 ~11,000 )
005 64 100ft
More 50 dB(AGC OFF)
ON
WDR / BLC/ OFF
True D&N(AUTO/ COLOR / BW)
Leveladjustable
AUTO/ MANUAL
Max. X64(X2, X4, X8, X16,X32, 64)
Average test illuminance by front view
Yes
Varifocal autoiris lens
14℉ ~ 122℉
-4℉ ~140℉
Ø130.8 X 96(H)mm
Approx.1.1 lbs
NTSC
Internal/ External
0. Lux(Senseup X ), 0Lux(LEDsON, Max. )
IR LED24pcs( )
X
Regulated 12VDC or 24V AC
Max. 500mA(at12V DC)/LEDON, Max. 510mA(at24V AC)/LEDON
Loading...