UserManual
Bluetoothaudioadapter
Modelname:BTR‐2M
FCCID:FWHBTR‐2M
IC:11909A‐BTR2M
BTR-2M MANUAL
The BTR-2M is easy to operate. One knob performs dierent
functions depending on how long you turn and hold it:
Instruction Duration
Tap
Press briey
Turn Approx: 1 second
Turn and hold Approx: 3 seconds
Black Gnd
Red +12v
Headphone Connector
Plug(3.5mm)
Mic
Bluetooth® device is connected to phones using a procedure called
pairing. By following a few simple steps, a phone can easily be
BTR-2M
paired with the
.
1. Press the knob and hold until you see red and blue LED
lights blinking . At this time, it gets into pair status.
2. Set your Bluetooth phone to search for the Bluetooth®
device (BTR-2M ).
Follow your phones instruction guide for Bluetooth® pairing. First
make sure that Bluetooth is activated on your mobile phone. Then
set your phone to discover the Bluetooth device. This usually
involves going to settings, connect or Bluetooth menu on your
phone and selecting the option to discover or add a Bluetooth
device. Your phone will nd the Bluetooth® receiver under the
name
BTR-2M
. After selecting
BTR-2M
your phone will conrm when
pairing is complete.
1
3. Connect BTR-2M to any equipment with auxiliary input.
4. Choose a spot to mount the external microphone in your vehicle.
Operation Instructions:
Play music
(Some phones may require you to start a media player
rst)
• Tap the knob once.
Pause music
• Tap the knob to pause, and tap again to resume playing.
Skip one track forward
• Turn the knob clockwise.
Skip one track back
• Turn the knob counter-clockwise.
Adjust volume UP
• Turn and hold the knob clockwise.
Adjust volume DOWN
• Turn and hold the knob counter-clockwise.
Answer a call
• Tap the knob to answer a call when phone is ringing.
Answer a call when playing music
• Tap the knob and the music will be paused and the call will be connected.
• When you end the call, your music will start again
End a call
• Tap the knob to end an active call.
Reject a call
• Tap and hold the knob when the phone rings to reject an incoming call.
Redial a call
• Double tap to redial the last call.
2
Installation Instructions:
• Hook the red wire to 12volt +
• Hook the black wire to 12 volt -
• Insert a 3.5 mm audio cable into the back of the device and connect
to your source or amplier.
Surface Mount Instructions:
Use the 2 Phillips screws to mount
Flush Mount Instructions:
Drill a 7/8" hole. Unscrew the locking
nut on the back of the device and pull
apart. Slide the unit thru the hole and
attach the nut on the back side.
Note: You can adjust the orientation of the knob in either of
the two mounting positions by loosening the nut on the back
side and rotating the knob to a dierent position. Example,
the mark can either be at 12, 3, 6 & 9 o'clock position.
NO.8, 68TH STREET, ZHONG MA ROAD,LAO WAI TAN, NINGBO 315020 CHINA
TEL: +86.574.873.88888 FAX: +86.574.876.77777 http://www.edgeholdings.com
3
This device complies with part 15 of the FCC rules. Operation is subject to the following
two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Loading...