AVS AVS-6000 Instruction Manual

AVS 6000 USER MANUAL

July 2003 EDITION

ALARM FEATURES

• 2 STAGE SHOCK SENSOR WITH AUTO ADJUST

• GLASS BREAK SENSOR

• BATTERY BACKUP SIREN

• TWO ROLLING CODE REMOTES (4 BILLION CODE VARIATIONS)

• TWO ON BOARD IMMOBILISER CIRCUITS

• AUTOMATIC IMMOBILISATION

• CENTRAL LOCKING OUTPUTS

• ON BOARD INDICATOR FLASH RELAYS

• BLACK CABLE LOOM

• SIMPLE PROGRAMING OF FEATURES FROM REMOTE CONTROL

• PERIMETER NIGHT LIGHT

• PAST ALARM TRIGGER MEMORY

• FAULTY SENSOR BYPASS

• MULTIPLE VEHICLE CONTROL

• ELECTRONIC BOOT RELEASE FROM REMOTE

• LED TORCH INCORPORATED INTO REMOTE

ALARM CERTIFICATION/STAR RATING

CERTIFICATION

THE AVS 6000 IS CERTIFIED TO AS/NZS3749.1:1997.

NEW ZEALAND SECURITY ASSOCIATION STAR RATING

THE AVS 6000 IS RATED 4 STAR.

INTRODUCTION

Thank you for purchasing the AVS 6000 alarm system for your vehicle. The AVS
6000 is designed to provide a high level of protection for your vehicle and has been
tested and certified to meet AS/NZS3749.1:1997.

SYSTEM FEATURES

Auto-immobilisation:

The AVS 6000 will automatically immobilise 38 seconds after the ignition is switched
OFF. The LED on the dash will light solid to indicate it is in auto immobilise mode.

Arm by remote (and lock if central locking is connected):

The system is activated by pressing the bottom button on the remote control. The
indicators will flash once and the siren will chirp once. If central locking is connected
the doors will lock. The LED light on the dash will stay on for 20 seconds then flash.
NOTE: For silent arm press the left and bottom button on the remote together.

Disarm by remote:

To disarm the system, press the bottom button on the remote. The indicators will
flash twice and the siren will chirp twice. The LED will stop flashing. If central locking
is connected the doors will unlock.
NOTE: If the alarm was activated while you were away from the vehicle the system
will flash the indicators and chirp the siren four times.
NOTE: For silent disarm press left and bottom button on the remote together.

Low remote battery warning:

When the battery in the remote is almost flat the remote’s LED will flash instead of
lighting constantly when a button is pressed.

LED torch:

Push top button on remote.

Auto re-arm and re-lock: (programmable):

If the system is disarmed and a door is not opened within 60 seconds it will re-arm
and re-lock the doors (if central locking is connected).

Door ajar warning:

If the vehicles doors are not properly closed when you try to activate the immobiliser
system, the indicators will flash and the siren will chirp six times to alert you that the
vehicle is not secure.

Panic/car finder:

The panic function is operated by pushing the right button on the remote. Cancel
panic by pushing the right button again.

Auto sensor bypass:

This function is designed to prevent false alarms from faulty sensors or switches. If
the system is triggered by the same sector three times then that particular sensor will
be bypassed. The sector will only be bypassed for one arming period, it will
automatically become active next time the alarm is armed.

Remote boot release:

This feature enables the user to unlock the boot by pressing the left button on the
remote for three seconds. The boot will unlock and the alarm will disarm with audible
beeps.
NOTE: Vehicles without electronic boot release will require an additional boot release
solenoid. See your installer.

Passive arming:

The alarm can automatically arm the alarm one minute after you leave the vehicle
provided that the ignition is turned off and at least one door has been opened and
closed. This feature will not lock the vehicle.

Pre warning impact sensor with ETS:

This special feature provides a two-stage impact sensor. It will give pre-warning
beeps for a few seconds if the sensor detects a light impact to the vehicle. If the
vehicle is attacked any further, the system will enter full alarm mode. The unique ETS
Environment Tuned Sensor is able to distinguish between environmental shocks
caused by aircraft, trucks, or extreme weather conditions, and the impact caused by
a thief attempting to break in or other heavy impacts.

Furthermore the system features the unique AVS “Auto Adjust” process, where
during the first 20 second arming delay, the alarm samples the background noise
where the vehicle is parked, and will, if necessary, automatically reduce the
sensitivity of the impact sensor to an appropriate level. This process allows trouble
free sensitivity that ordinary impact sensors cannot provide.

Please refer to the programming section later in this manual for setting the shock
sensor.

Glass break sensor:

The AVS 6000 incorporates an intelligent glass break sensing system. This inbuilt
device will trigger the alarm provided it registers the correct sound frequency
parameters for breaking glass and that the impact sensor also registers a
corresponding vibration to the vehicle. This ensures accurate detection of glass
breakage.

Past alarm trigger memory:

If the alarm was triggered by an intruder while your alarm was set, it will beep the
siren and flash the indicators four times on disarm. The system will also store the last
10 times the alarm has been activated in its memory and can tell you what has
triggered the system. Please refer to the programming section later in this manual for
details on retrieving memory.