AC-EX100-UHD
AVProConnect
3518 N Casco Avenue ~ Sioux Falls, SD 57104
1-877-886-5112 ~
605-274-6055
supp
ort@avproconnect.com
AC-EX100-UHD-T
&
AC-EX100-UHD-R (v1 & v2)
100M HDMI 2.0 Extender With HDCP 2.2
Ethernet, Audio Extraction, EDID Management
1
Introduction
The AC-EX100-UHD is a 100m HDBaseT Tx/Rx with Bi-Directional Power,
RS-232, IR, Ethernet, Audio Extraction and EDID Management.
Key benefits of using AC-EX100-UHD:
1) ULTRA HIGH DEFINITION: Our AC-EX100-UHD supports 4K up to 70M
(230FT) & HD up to 100M (330FT) with crystal clear 4K Resolution. NOTE:
High Quality CAT6a Shielded required for maximum performance.
2) DISTANCE: By using AC-EX100-UHD, the transmission distance for HD
1080P up to 100 meters (330’) & 4K up to 70M (230')
3) EDID MANAGEMENT: Control the source device with EDID management.
With the multitude of sources out there, this feature allows you to fix a known
good EDID so the source device knows what to output.... every time.
4) CONTROL: IR & RS-232 are bidirectional and can control the sources from
the sinks or vice versa. This allows unlimited flexibility when controlling sinks,
and sources. Control the rack or source and the display or sink over the same
single wire.
5) BI DIRECTIONAL POWER: Ultra stable bi directional PoE allows you to
really be flexible as you can choose where you want to power. Eliminate power
supplies at the rack and power the Tx remotely from the display (Rx) end.
NOTE: AC-EX100-UHD-Rv2 Required.
6) AUDIO EXTRACTION: The Tx on the pair had audio outputs for PCM audio
- You have balanced 2-channel and SPDIF outputs to run audio directly into a
local AVR or even more common, use the 2-channel audio to go into a
distributed audio amplifier/matrix.
7) I-PASS: Plug you Control System emitter ports directly into the IR port on
the transmitter (via mono 3.5mm cable) for clean and reliable IR pass through,
our unique VPC (Voltage Protection Circuit) allows you to do this without wear
and tear on the sensitive electronics inside.
2
AC-EX100-UHD
Applications:
This long range (up to 100m, 330ft & 70m 4K) is unrivaled when it comes
to the features it comes with. these extenders are designed to be a true
problem solver. When the situation requires more power, distance, added
Ethernet and reverse power or control, the B.A.E has it covered. Using the
most powerful HDBaseT technology on the market, this product is sure be
a robust long lasting part of your infrastructure.
3
AC-EX100-UHD
Tx
Rx
Rx
Tx
Long Range Extender w/ Ethernet, EDID & Control
■ Product Overview
■ Model Numbers:
• AC-EX100-UHD-T ~ HDBaseT Transmitter w/ Audio Extraction,
Ethernet (2-ports), IR, RS-232, EDID & Bi-Directional PoE
• AC-EX100-UHD-R ~ HDBaseT Receiver w/ Ethernet (1-port), IR,
RS-232, PoE (not bi-directional)
• AC-EX100-UHD-R2 ~ HDBaseT Receiver w/ Ethernet (2-ports),
IR, RS-2323 & Bi-Directional PoE
■ Features
• HDMI 2.0
• 4K60 4:2:0, 4K30 4:4:4
• HDR Support up to 4:2:2 12 Bit
• Supports 3D
• HDCP 2.2 & HDCP
• CEC Pass Through
• 100M (330ft) on 1080P (Cat6a)
• Up to 70m (230ft) on 4K (Cat6a)
• Bi Directional 48v PoE
• Ethernet hub & extension
• Audio Extraction on Tx (SPDIF, Balanced 2ch, PCM Only)
• EDID Management
• I-Pass Feature for control system "pass-through"
• 3-20v protection circuit built in for safe IR transport
• ieee PoE for universal HDBaseT Installations
• Compatible with HDBaseT displays, projectors, AVR's
• Supports uncompressed PCM 2- Ch., 5.1, 7.1, Dolby Digital, DTS,
Dolby TrueHD, DTS HD-Master Audio and more.
• Can Cascade
4
AC-EX100-UHD
Notice
AVProConnect reserves all the right to make changes in the hardware,
packaging and any accompanying documentation without prior written notice.
Warning
To reduce the risk of fire, electric shock or product damage:
Basic
1. Do not expose this device to
rain, moisture, dripping or
splashing and ensure that no
objects filled with liquids are
placed on or near the devices.
6. Clean this device with
a dry cloth only.
2. Do not install or place this unit
in a bookcase, built-in cabinet or
in another confined space.
Ensure the unit is well ventilated.
3. To prevent risk of electric
shock or fire hazard due to
overheating, do not obstruct
the unit’s ventilation openings
with newspapers, tablecloths,
curtains, and similar items.
4. Do not install near any heat
sources such as radiators, heat
registers, stoves, or other
apparatus (including amplifiers)
that produce heat.
5. Do not place sources of naked
flames, such as lighted candles,
on the unit.
7. Unplug this device
during lightning storms or
when unused for long
periods of time.
8. Protect the power cord
from being walked on or
pinched particularly at
plugs.
9. Only use attachments /
accessories specified by
the manufacturer.
10. Refer all servicing to
qualified service
personnel.
5
AC-EX100-UHD
■ Available Kits & What's Included
6
AC-EX100-UHD
NOTE: Standalone Transmitters & Receivers can be purchased standalone as
well in needed to use with other HDBaseT Compatible devices like Displays,
Projectors, AVR's, etc... For thes best advice when purchasing a standalone
Transmitter or Receiver please consult your AVPro Sales Manager or your
distributor. Standalone Receivers and Transmitters can be purchased online
at www.avprostore.com
7
AC-EX100-UHD
■ Specifications
8
AC-EX100-UHD
■ Using Bi-Directional Power (Receiver V2 Required)
Using the Bi-Directional PoE feature is fairly easy to do, and even though the ACEX100-UHD System is designed to handle "hot" changes. We strongly
recommend you switch directinal power while the units are completely
unplugged from Power, HDMI or CAT Cable.
1. To set the direction of the power, select where you want the power to
ORIGINATE from on both the Transmitter and Receiver units.
2. Be sure you have the Power Supply plugged in on the newly selected PoE
origination side.
3. Continue normal operation.
4. See photo below to see what the switches look like.
NOTE: The PoE Directional Switches must always MATCH!
Tx
Rx
9
AC-EX100-UHD
■ RS-232 Configuration
RS232 can be used to pass control signals bi-directionally to & from any
RS232 compatible device. This is commonly used to rout control signals
in the following way:
1. Control System --> Display/Projector (ie, Power On/Off)
2. Display/Projector --> Control System (ie, Display Status, Volume
Status etc...)
3. As a long range serial port extender (ie, Use the extender when you
need ultra long range serial communication at concerts, live events
etc...)
The unit comes with 3 pin
connectors to use any wire you
would like, the Pin out configuration
Left=Tx, Center=Ground, Right=Rx
and looks like this:
This is how your cable shold look.
If you are using the AC-CABLE-3.5DB9F (Female) or AC-CABLE-3.5DB9M (Male), the colors will be the
same as well. With any other
cable, please follow Tx, G, Rx as
shown above. A RS-232 Cable
Preparation diagram is on the next
page.
AC-EX100-UHD
■ RS-232 Cable Prep
■ RS-232 Sample Application
10
11
AC-EX100-UHD
■ IR Configuration
IR can be used in 2 ways:
1. From Rack (Control System Direct): Plug
a MONO 3.5mm cable
into an emitter port of any control system directly into the "IPASS" (IR RX) Port on the AC-EX100-UHD Transmitter to send pass IR
Signals directly to the remote end.
2. From Remote End: Use and IR Sensor on the AC-EX70-UHD
Receiver (IR In Port) and send IR Signals BACK to the rack and come
out of the TRANSMITTER IR Out Port with an emitter.
*There is a 3-20v protection circuit built into the AC-EX100-UHD-T
Transmitter to safely plug IR signals directly into it for pass through to
the remote end.
AC-EX100-UHD
■ IR Connections to AC-EX100-UHD-T (Transmitter)
■ IR Connections to AC-EX100-UHD-R (Receivers)
12
13
AC-EX100-UHD
■ Audio Extraction on AC-EX100-UHD-T (Transmitter)
Audio Extraction is an always active feature on the AC-EX100-UHD-T.
This feature extracts PCM Audio Only (2ch or 6ch) from the source
device to be ran to a separate amplifier or AVR. BOTH the audio ports
are always active (balanced stereo & SPDIF).
To use the ports:
1. Simply plug a balanced stereo 5 pin or SPDIF Digital Coax cable in
to begin extracting audio. (Please view photo for port locations)
2. You can optionally buy pre made Balanced 5-pin to RCA Female
cables from AVProStore.com
NOTE: The source device needs to be outputting PCM audio in order
for the feature to work, this can be done by using the on-board
EDID management or setting the source as such.
Tx
Balanced
Stereo
SPDIF
(Digital Coax)
14
AC-EX100-UHD
■ Audio Extraction Routing Diagram
■ Stereo Cable Preparation
NOTE: Pre-made audio cable can be purchased from www.avprostore.com. The part
number is: AC-CABLE-5PIN-2CH
15
AC-EX100-UHD
■ Advanced EDID Management
Advanced EDID Management is a unique and extremely powerful
feature of the AC-EX100-UHD-T. EDID problems are common in
todays installations and this feature overcomes that problem.
By default the EDID is set to position "0" (See Chart) - This reflects the
absolute maximum capabilities of the HDBaseT Link. You should rarely
have to change EDID, even when using 4K! If you need to set the
EDID to fix a lower resolution from a source or have other connectivity
problems, simply rotate the dial to the corresponding EDID below.
ROTARY SWITCH POSITION:
0-4k60 420 3D 8ch - FACTORY DEFAULT
1-4k60 420 3D 6ch
2-4k60 420 3D 2ch
3-4k30 444/RGB 3D 8ch
4-4k30 444/RGB 3D 6ch
5-4k30 444/RGB 3D 2ch
6-1080p60 444/RGB 3D 8ch HDR
7-1080p60 444/RGB 3D 6ch HDR
8-1080p60 444/RGB 3D 2ch HDR
9-1080p60 444/RGB 3D 8ch
A-1080p60 444/RGB 3D 6ch
B-1080p60 444/RGB 3D 2ch
C-1080p60 RGB 2ch
D-1080i60 444/RGB 2ch
E-1080p24 444/RGB 2ch
F-SINK COPY = Copy Connected Device EDID - NOTE: If connected
device has an EDID above 300MHz then the result will be a black
screen, please only use this if the connected device supports 1080i/p or
maximum of 4K60 4:2:0.
EDID Rotary Switch:
Use a small, flat,
electronics
screwdriver or pots
adjuster to set - Set
to desired EDID on
the left.
16
AC-EX100-UHD
■ Using Ethernet
Using Ethernet is a valuable feature for expanding the LAN in the
commercial or residential space you are working in. The simple to use
feature allows you simply plug & play the network expansion.
1. Simply plug in one of the Ethernets ports on the AC-EX100-UHD
Tx or Rx to the main switch, hub, router, etc...
2. The additional Ethernet ports of the AC-EX100-UHD Tx and Rx are
now available for PC's, Gaming Consoles, Local Media/Music
players to access the LAN or INTERNET.
3. You can also use the link on your AC-EX100-UHD to expand your
WiFi Range - See Diagram below.
4. Remember, you do not need to be concerned where devices get
plugged in as it is all bi-directional, meaning the router/hub can be
on either side of the HDBaseT link. See diagram below.
Ethernet (LAN)
Connected device
LAN Router
● Warranty
If your product does not work properly because of a defect in materials or
workmanship, AVProConnect (referred to as “the warrantor”) will, for the
length of the period indicated as below, （Parts/Labor (10)
Years）which starts with the date of original purchase (“Limited Warranty
period”), at its option either (a) repair your product with new or
refurbished parts, or (b) replace it with a new or a refurbished product. The
decision to repair or replace will be made by the warrantor.
During the “Labor” Limited Warranty period there will be no charge for labor.
During the “Parts” warranty period, there will be no charge for parts. You must
mail-in your product during the warranty period. This Limited Warranty is
extended only to the original purchaser and only covers product purchased as
new. A purchase receipt or other proof of original purchase date is required for
Limited Warranty service.
17
AC-EX100-UHD
Damage Requiring Service: The unit should be serviced by qualified
service personnel if:
The DC power supply cord or AC adaptor has been damaged;
Objects or liquids have gotten into the unit;
The unit has been exposed to rain;
The unit does not operate normally or exhibits a marked change in
performance;
The unit has been dropped or the housing damaged.
■ Maintenance
Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner or
benzene to clean this unit.
● Warranty Limits and Exclusions
1) This Limited Warranty ONLY COVERS failures due to defects in
materials or workmanship, and DOES NOT COVER normal wear
and tear or cosmetic damage. The Limited Warranty ALSO DOES NOT
COVER damages which occurred in shipment, or failures which are caused
by products not supplied by the warrantor, or failures which result from
accidents, misuse, abuse, neglect, mishandling, misapplication, alteration,
faulty installation, set-up adjustments, misadjustment of consumer
controls, improper maintenance, power line surge, lightning damage,
modification, or service by anyone other than a Factory Service Center or
other Authorized Service, or damage that is attributable to acts of God.
2) There are no express warranties except as listed under “limited
warranty coverage”. The warrantor is not liable for incidental or
consequential damages resulting from the use of this product, or
arising out of any breach of this warranty. (As examples, this
excludes damages for lost time, cost of having someone remove or
re-install an installed unit if applicable, travel to and from the service
location, loss of or damage to media or images, data or other recorded
content. The items listed are not exclusive, but are for illustration only.)
3) Parts and service, which are not covered by this limited warranty,
are on user responsibility.
Adress:
3518 N Casco Ave , Sioux Falls, SD 57104
Tel: 877-886-5112 605-274-6055
18
AC-EX100-UHD
19
AC-EX100-UHD
■ Notes:
20
AC-EX100-UHD
AVProConnect
3518 N Casco Avenue ~ Sioux Falls, SD 57104
1-877-886-5112 ~ 605-274-6055
support@avproconnect.com
Thank you for choosing AVProConnect!
Please contact us with any questions, we are happily at
your service!
Loading...