Avocor AVE-6510 Quick Start Guide

AVE Series

Quick Start Guide

AVE-6510, AVE-7510, AVE-8610

E Series Quick Start Guide Table of Contents

3. Contents of Packaging

4. The Display at a Glance

7. Display Input Sources

9. The Remote Control

10. Switching the display on and off
Source Selection

Connecting to the Display

11. Connecting to an external PC using a HDMI connection

12. Connecting to an external PC using a DisplayPort connection

13. Enabling the Touch System

14. Installing an OPS Module

15. Warranty Support

v.08_08_20

18 2

Contents of Packaging

1. Accessory Carton

• Quick Start Guide

• Remote Control & Batteries

• 2x Touch Stylus – 1x3m m & 1x6mm

• Eraser

• Power Cables - UK Cable 2m & European Cable 2m

• 2x 3m HDMI Cable

• 2x 3m USB-A – USB-A Cable

• Cleaning Cloth

• Pen Holder

Please visit www.avocor.com to download the full E-Series user manual
and the Pen Aware Touch Drivers.

v.08_08_2018 3

The Display at a Glance

Front View

Rear View

v.08_08_2018 4

v.08_08_2018 5

Front Buttons

Button

Operation

Function

Power on/off Indicator

LED status:

● Solid Red : Sleep mode

● Solid Green : Working state

Source

Short press

Open the Source menu

Short press

Decrease the audio volume in steps

Power Short Press

● Blinking Red and Green : Standby mode

Menu Short press Open the Settings menu

Mute Short press Mutes the audio

VOL -

VOL+

Long press - more than 1 sec Decrease the sound volume continuously
Short press Increase the audio volume in steps
Long press - more than 1 sec Increase the sound volume continuously

v.08_08_2018 6

E-Series Display Inputs

Front Ports

v.08_08_2018 7

Rear Ports

v.08_08_2018 8

Remote Control

Label

Description

Navigates through menus and settings.

Turns the display on and off.

Select the OPS PC source.

Blanks the display. Press again to restore.

Freezes the display. Press again to restore.

Opens the display menu system.

Decreases the Volume by pressi ng t h e - key

Increases the Volume by pressing the + key

Opens the Source Menu.

Selects DisplayPort

When the menu system is already open, pressing

Mutes the audio. Pressing Mute again restores the

Selects highlighted menu choice

this button will close the on screen menu.

audio

v.08_08_2018 9

Selects the HD M I Sour c es

Selects each aspect ratio, in sequence: Full

Screen, Auto, Pillar Box

Switching the Avocor display on and off

Switching on

1. Plug the end of the supplied power cord i nto side of the display

2. Connect the other end to the power source.

3. Turn on the main power switch at the side o f the display. The power LED indicator lights
Red to indicate that the display is in “standby” mode.

4. Press the Power button and the power L ED indicator on the left-hand side of the display
will then light up in g reen, which tells you that the screen is switched on.

5. After a brief warm-up period, the display will display an image

Switching off

1. Switch the display off by pressing the Power button on the display.

2. The display will then cycle and shut down.

Selecting the Source

You can access several sources on the Avocor E-Series display including, HDMI ,
DisplayPort, & OPS.

The Source button is located on the Connect & Control Bar or on the Remote Control.
Once the menu has been selected, you will see the option to select the source you
require.

HDMI 1, HDMI 2, HDMI 3, DisplayPort, OPS, & Front HDMI
If there is no active signal from the chosen source, the screen will display the following

message: “No Signal”.

Connecting the Display

Proceed as follows to connect the display to your video sources, external controller.
When connecting your equipment:

1. Turn off all equipment before making any connections.

2. Use the correct signal cables for each source.

3. For best performance and to minimise cable clutter, use high-quality cables that are
only as long as necessary to connect two devices. (Don't use a cable longer than 5
metres).

4. Ensure that the cables a re securely connected.

v.08_08_2018 10

Connecting to an external PC using a HDMI
connection

In addition to a HDMI connection, a USB touch connection is required when connecting
an external PC.

1. Connect the enclosed HDMI cable to the HDMI port of the touchscreen and to the

external PC.

2. Connect the enclosed USB cable to the corresponding touch USB port (USB-A) of

the touchscreen and to the USB port (USB-A) on the external PC.

3. Using the Remote Control select the HDMI source button or press the Source Button

(see operating buttons) on the Front Connection bar to select HDMI.

This display supports the VESA Display Data Channel (DDC)
standard. This standard provides “Plug and Play” capability;
the display and a VESA DDC-compatible computer
communicate their setting requirements, allowing for quick
and easy setup.
In order for Plug and Play to work correctly, you must turn
on the display before you turn on the connected
computer.

We recommend using a USB cable that is no longer than 5
metres.

v.08_08_2018 11

Connecting to an external PC using a
DisplayPort connection

In addition to a DisplayPort connection, a USB touch connection is required when
connecting an external PC.

4. Connect a DisplayPort cable to the DisplayPort port of the touchscreen and to the

external PC.

5. Connect the enclosed USB cable to the touch USB port (USB-A) of the touchscreen

and to the USB port (USB-A) on the external PC.

6. Using the Remote Control select the DisplayPort source button or press the Source

Button (see operating buttons) on the Front Connection bar to select DisplayPort.

In order for Plug and Play to work correctly, you must turn on
the display before you turn on the connected computer.

We recommend using a USB cable that is no longer than 5 metres.

v.08_08_2018 12

Enabling the Touch Screen

Before setting up your display to suppor t touch screen capability, ensure that:

• The touch screen controller host computer is turned off.

• The display is turned on.

• The video output from the computer is connected to a video input on the display.

Connecting the Display to a Host Computer

1. Connect the signal cable to th e di s play , and then turn on the display.

2. Connect the USB Cable (USB Type-A connector) to the display.

3. Connect the other end of USB cable (USB T ype-A) to the USB port on the laptop/ PC.

See picture below.

4. Then turn on the computer.

5. When USB cable is fully connected, wait fo r 5 seconds and the touch function is

ready. It can be activated by using the stylus or finger.

v.08_08_2018 13

Installing an OPS Module

Step 2

Step 3

Step 4

Step 5

Follow the steps below to install an OPS module.

Step 1. Ensure that the display is turned off
Step 2. Use a screw driver to unscrew the OPS slot shield on the display input panel. D o not

lose the screws tha t are removed.
Step 3. Install the OPS module by sliding it into the OPS slot until you hear a click, indicating

the module is securely inserted. When using an Avocor OPS PC, the fan should be visible
Step 4. Secure the OPS module in position by screwing it onto the display input panel using

the screws that wer e removed earlier.

Step 5. Ensure the installation is complete before turning on the po wer.
Step 6. Turn on the display. When using an Avocor OPS Pc you should see a green light on

the side of the OPS, this will indicate that the OPS PC is switched on and operationa l.

Note. When installing or de-installing an OPS PC, the display must be switched off. If the display is on when
performing the installation or deinstallation of the OPS PC, this could cause damage to either the display or OPS
PC invalidating the warranty for both.

v.08_08_2018 14

Warranty Support

Organisation Name

Contact Person

1st Contact Number (Landli n e)

2nd Contact Number (Mobile/Cell)

Email

Address

(of on-site repair or unit exchange)

City

State

Postcode/ZIP

County/State

Days and hours of operation

Loading & Parking Available? (Yes or No)

Reseller Information (If Known)

Organisation Name

Contact Person

Contact Number (Landli ne)

Email

Product Information

Product / Model

Serial Number

Date of Purchase (If Known)

Should you require assistance with any suspected hardware fault, please contact the
Warranty Support team. Please provide as much i nformation to the support team about
the fault and any steps you have taken in trying to try and resolve the fault.

Remember the first instance to look for known faults and how to resolve them on the
avocor Website www.avocor.com/support

UK & EMEA. Tel +44 (

v.08_08_2018 15

UK Warranty Support

0) 1276 804 654 -

[e-mail]

v.08_08_2018 16