Avnet SEIIOTG User Manual
SmartEdge Industrial IoT Gateway
Quick Start Guide
POWER INPUT
An external power supply is required. Rating: 12VDC to 24VDC (+/- 10%), 18W minimum, 24W
recommended, LPS (Limited Power Source). Use 16-22AWG power supply wiring, stripped
back 4-5mm, twisted & optionally tinned. Find the black, 3 position terminal plug in the
included hardware kit. Insert the prepared wires into the terminal plug, observing proper
location. The wire polarities are indicated on the enclosure and shown below. An Earth GND
wire is recommended (not included).
Signal DC Input
Earth GND
- 0V (GND)
+ 12-24VDC
5) Signup: Launch the App and enter your
details to create a new account, or
Cancel to login to an existing account
6) Login: Enter your account email address
and password to login
CAUTION: Verify terminal block wiring is correct, tight, and with no bare wiring exposed
INSTALLATION
Follow this installation process to connect your Avnet SmartEdge IIoT Gateway to the cloud.
1) Connect your SmartEdge Gateway to your Ethernet network, if available, by using one of
the two Ethernet Ports. If using wireless, this will be set up in a later step.
2) Plug in the correctly wired power supply plug to start the unit
3) Refer to the online datasheet (insert link to product web portal here) for detailed
information on the remaining hardware connections.
4) Download the mobile application to register your SmartEdge Gateway with the IoT
Connect cloud by scan the appropriate QR code below with your mobile device, or
search for <APP NAME> on the app store):
Apple iOS App
Store Link
QR Code
Android Play
Store Link
QR Code
7) Add Device, tap lower right, then tap
"Add Device" +
8) Connect to your device using your
mobile's WiFi settings
iOS Android
9) Optionally, connect your SmartEdge
Gateway to your local WiFi network
10) Now you can see your device listed in
the Device List
11) Tap your device to see the device details 12) Tap the sensor to view sensor readings
13) You can also view your sensors from the IoT Connect Web Portal (name?) (link to IoT
Connect web interface)
IMPORTANT NOTICES
Lithium Coin Battery - BR1225
CAUTION: Risk of explosion if the battery is replaced by an incorrect type. Dispose of used
batteries according to the battery manufacturer's instructions.
CAN ICES-3(B) / NMB-3(B)
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic
Development Canada’s license-exempt RSS(es). Operation is subject to the following two conditions: (1)This device may not
cause interference; (2)This device must accept any interference, including interference that may cause undesired operation
of the device.
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator and your body.
L’émetteur / récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et
Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux
conditions suivantes: (1)L’appareil ne doit pas produire de brouillage; (2)L’appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
Cet équipement est conforme aux limites d'exposition aux radiations IC CNR-102 établies pour un environnement non
contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 20 cm entre le radiateur et votre corps.
FCC Statement
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV technician for help
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with minimum distance 20cm between the radiator and your body. This transmitter must
not be co-located or operating in conjunction with any other antenna or transmitter.
www.element14.com/gateway May 16, 2019
Loading...