Avlink VAX-8404F User Manual
VIDEO/AUDIO
MATRIX
(VAX-8404F)
USER MANUAL V1.0
VAX-8404F
Package Contents-
1 AVLINK VX-8404F video/audio matrix
1 user manual
1 power adapter DC 12V 1.25A
2 rack rails, 8 screws
Any thing missed, please contact with your vendor.
4 In 4 Out
Introduction
Through the video/audio matrix VX-8404F, you can display / play
different images / audio signals to 4 screens / speakers (or
earphones) through 4 PC. And you can also control the source of
image / audio by selecting PC signal source 1 ~ 4 or turning off
source input.
Video/Audio matrix is ideal for:
Test bench facilities
Data center
Help desks
Video broadcasting:
Presentation
Stock quotes
Timetables
Educational facilities
Features
Intelligent functionality.
With 350 MHz pixel frequency.
Support VGA, SVGA, UXGA, QXGA resolutions.
Support Multi-Sync video type include RGBHV, RGsB, RGBS.
Support synchronous Include positive, negative; TTL or 1Vpp
level.
Supports the DDC, DDC2, DDC2B.
Four sets of 7-Segment LED can indicate the input setting
status of input port quickly.
Can be cascaded.
The output is compatible with standard VGA card.
Extends the video signal up to 65 meter (213 feet).
The switches on panel can select PC signal source 1 ~ 4 as
OUT 1 ~ 4 or turning off any signal I/O port / all I/O ports.
Specifications
Function VAX-8404F
Video Input Connector 4x HD-15 Female
Video Output Connector 4x HD-15 Female
Audio Input Connector 4x 3.5φ Stereo Jack
Audio Output Connector 4x 3.5φ Stereo Jack
Select Switch 10
7-Segment LED 4
Max. Resolution 1920x1440 @ 85 Hz
Pixel Frequency 350 MHz
Cable Distance
(Device to Monitor)
Power Adapter (Min.) DC 12V 1.25A
Housing Metal
Weight 1065 g
Dimensions (LxWxH) 269x108x42 mm
65m (213 feet) Max.
-1-
Technical Specifications
Input/Output Signal
Pin # Signal
1 Red video 9 NC
2 Green video 10 Ground
3 Blue video 11 NC
4 NC 12 ID1
5 Ground 13 Horizontal sync
6 Analog ground 14 Vertical sync
7 Analog ground 15 ID3
8 Analog ground
FRONT VIEW
1. Select Switch
7-Segment LED
2.
REAR VIEW
1. Input Power Jack
Audio Out” Port
2. “
3. “Audio In” Port
4. “Video Out” Port
5. “Video In” Port
Pin # Signal
Installation
1. Turn off the power switches of PC, screens, and speakers.
2. Use HD-15 image / 3.5φ earphone extension cable to
connect VGA interface / audio card in PC and the “Video
In“ & “Audio In“ jack of video/audio matrix.
3. Use HD-15 image / 3.5φ earphone extension cable to
connect screen, speaker, or earphone and the “Video Out“ &
“Audio Out“ jack of video/audio matrix.
4. Connect video/audio matrix to power supply.
5. Turn on the power switches of PC, screens, and speakers.
6. Control switches, which includes “Out1“, “Out2“, “Out3“,
“Out4“, “All“, “In1“, “In2“, “In3“, “In4“, and “OFF“, on panel can
get image / audio signals or turn off input signal through
output jack.
-2-
Operation
1. When you press button “Out1“ or “Out2“ or “Out3“ or “Out4“,
the corresponding Out 7-Segment LED will start flashing for
3 seconds. There are total three switching methods:
a. a. Press button “In1“ or “In2“ or “In3“or “In4“ within 3
seconds to make 7-Segment LED stop flashing and
change its display to the number of Input port you set.
Then the Output port will switch to the corresponding
Input port.
b. b. Press button ”OFF” within 3 seconds to make
7-Segment LED stop flashing and display ”0”. Then this
Output port will be turned off.
c. c. If you don’t press any button within 3 seconds, the
7-Segment LED will stop flashing and keep displaying
original number and setting of Output port.
d. d. If you press button “Out1“ or “Out2“ or “Out3“ or
“Out4“ within 3 seconds, then Out 7-Segment LED will
start flashing for 3 seconds again to wait for button
“In1“ or “In2“ or “In3“ or “In4“, “OFF” pressed.
2. When you press button ”All”, all 7-Segment LED will start
flashing for 3 seconds. There are total three switching
methods:
a. Press button “In1“ or “In2“ or “In3“or “In4“ within 3
seconds to make all 7-Segment LED stop flashing and
change their displays to the number of Input ports you
set. Then all Output ports will switch to the
corresponding Input ports.
b. Press button ”OFF” within 3 seconds to make all
7-Segment LED stop flashing and display ”0”. Then all
Output ports will be turned off.
c. If you don’t press any button within 3 seconds, all
7-Segment LED will stop flashing and keep displaying
original number and setting of Output port.
d. If you press button “All“ within 3 seconds, then all Out
7-Segment LED will start flashing for 3 seconds again to
wait for button “In1“ or “In2“ or “In3“ or “In4“, “OFF”
pressed.
Note:
When video/audio matrix is connected to power supply, the
initial setting of jack connection is: ”Out1” to ”In1”, ”Out2”
to ”In2”, ”Out3” to ”In3”, ”Out4” to ”In4”.
If you install DDC monitor for video/audio matrix, then the
setting of DDC will be applied to the other monitors.
To get the functionality of DDC monitor, please connect the
following jacks: “Video In1” to “Video Out1”, “Video In2” to
“Video Out2”, “Video In3” to “Video Out3”, and “Video In4” to
“Video Out4”.
Available monitors include the VGA, SVGA, UXGA, QXGA,
Multisync, and exclude the CGA, EGA, Mono.
-3-
Operation for cascade:
1. The function to display image on more monitors, you
request to attach another video/audio matrix or the
standard video/audio splitter.
2. Connect the HD-15 male/male video extension cable
between the “Video Out” port of the former video/audio
matrix and the “Video In” port of the latter video/audio
matrix.
3. Connect the
cable between the “Audio Out” port of the former
video/audio matrix and the “Audio In” port of the latter
video/audio matrix.
Note:
Even though you are allowed to cascade the video/audio
matrix with varied ports, the image might become unstable
if cascade too many tiers of video/audio matrixes.
© C&C TECHNIC TAIWAN CO., LTD. All rights reserved.
Trademarks:
All the companies, brand names, and product names
referred to this manual are the trademarks or
registered trademarks belonging to their respective
companies.
3.5φ Stereo plug male/male audio extension
-4-
Loading...