HDMI
EXTENDER
HDMI-SLW HDMI-ELW
(Local)
HDMI-SRW HDMI-ERW
(Remote)
USER MANUAL V1.0
HDMI-SXW / HDMI-EXW
Package Contents-
1x HDMI-SLW or HDMI-ELW L oc al Unit
1x HDMI-SRW or HDMI-ERW Remote Unit
1 user manual
2x Power adapter DC 12V with lock
1x HDMI 1.2M cable
1x IR Blaster Cable(Peak Wavelength 940nm)
1x IR Receiver Cable
4x screws
8x foot pads
Any thing missed, please contact with your vendor.
Features
Through the HDMI Extender, you ca n use one DVD to
display identical image and extension of HDMI signal
up to 70/100 meter on HDTV
HDCP Compliant
Supports 3D pass-through
Supports CEC pass-through
Support RS-232(Bi-direction transfer)
Supports all frequency band IR control
One CAT.5 cable extension
Supports HDTV up to 1080p
HD-baseT technology
Use CAT.5 cable to install easily
Specifications
Function
HDMI In
Connector
HDMI Out
Connector
RJ-45 Connector 1
IR OUT
IR2 IN None
Max. Resolution 1080P 60Hz
Cable Distance 70 m 100 m 70 m 100 m
Power Adapter
(Min.)
Housing Metal
Weight 305g 308g
Dimensions
(LxWxH)
HDMI-SLW HDMI-ELW HDMI-SRW HDMI-ERW
HDMI A-Type Female
x 1
None HDMI A-Type Female x 1
3.5ψ Stereo Jack x 1
3.5ψ Stereo Jack x 1
DC 12V with lock
150x80x25 mm
-1-
None
None
LOCAL FRONT VIEW
1. IR OUT
2. HDCP LED
3. LINK LED
4. MODE LED
5. POWER LED
LOCAL REAR VIEW
1. Power jack (12V DC)
2. LINK (RJ-45 Connector)
3. HDMI BYPASS(Only HDMI-ELW)
4. HDMI IN
5. RS-232
REMOTE FRONT VIEW
1. IR2 IN
2. IR1 IN
3. HDCP LED
4. LINK LED
5. MODE LED
6. POWER LED
REMOTE REAR VIEW
1. Power jack (12V DC)
2. LINK (RJ-45 Connector)
3. HDMI OUT
4. RS-232
-2-
Installation
1. Turn off the DVD and HDT V.
2. Connect the HDMI extension cable between the DVD
and the “HDMI IN” port of HDMI-SLW or HDMI-ELW.
3. Connect the HDMI extension cable between the HDTV
and the “HDMI OUT” port of HDMI-SRW or HDMI-ER W.
4. Connect the CAT.5 cables between the HDMI-ELW
“LINK” port and the HDMI-SRW or HDMI-ERW “LINK”
port of extender.
5. Connect the power cord and turn on the extender.
6. Turn on the DVD and HDTV.
※When HDMI-ELW is in BYPASS mode the LINK port
should be left unused.
IR Receiver Cable Directions:
Put it into the HDMI-SRW or HDMI-ERW “IR2 IN” port and
place the IR Receiver Cable, so that you can point to it
easily with your IR remote controller.
IR Blaster Cable Directions:
Plug IR blaster cable plug into HDMI-SLW or HDMI-ELW
“IR OUT” port, It sits in front of the DVD receiver’s IR
sensor, which is located on the front-panel.
Additional Options
Select any additional options you may require.
1. IR Receiver Cable
GND
+V
Sig
2. IR Blaster Cable
NC
P+
N-
Technical Specifications Output Signal
Pin # Signal Pin # Signal
TMDS Data 2+
1
TMDS Data 2 Shield
2
TMDS Data 2-
3
TMDS Data 1+
4
TMDS Data 1 Shield
5
TMDS Data 1-
6
TMDS Data 0+
7
TMDS Data 0 Shield
8
TMDS Data 0-
9
TMDS Clock+
10
TMDS Clock Shield
11
TMDS Clock -
12
CEC
13
Reserved
14
(N.C. on device)
SCL
15
SDA
16
DDC/CEC Ground
17
+5 Power
18
Hot Plug Detect
19
Wiring Information & Coding
Conductor
Identification
Pair 1
Pair 2
Pair 3
Pair 4
RJ45 Pin
Assignment
Color Code for
Conductor
5 White-Blue
4 Blue
1 White-Orange
2 Orange
3 White-Green
6 Green
7 White-Brown
8 Brown
Note
However sometimes, especially in demonstrations or in a
lab environment, the cable is rolled randomly in small turns
for convenience. The randomly rolled UTP cable suffers
additional signal impairments (compared to a straight cable)
and therefore the maximal operating reach might be
reduced.
Rolling a CAT5E cable around a 70cm fixed diameter
plastic drum has just a minor effect on the FEXT (Far End
Cross Talk) when compared to a fully stretched
cable.
© C&C TECHNIC TAIWAN CO., LTD. All rights reserved.
Trademarks:
All the companies, brand names, and product names
referred to this manual are the trademarks or registered
trademarks belonging to their respective companies.
-3-
-4-
-5-
Loading...