Avlink DVI-EPXW User Manual

DVI
EXTENDER

USER MANUAL V1.0

DVI-EPXW

LOCAL FRONT VIEW

Package Contents-

 1x DVI-EPLW Local Unit
 1x DVI-EPRW Remote Unit
 1 user manual
 1x Power adapter DC 48V with lock
 1x AC power cable
 1x DVI 1.2M cable (DVI-D Male to Male)
 1x IR Blaster Cable(Peak Wavelength 940nm)
 1x IR Receiver Cable
 4x screws
 8x foot pads

Any thing missed, please contact with your vendor.

1. IR OUT

2. HDCP LED

3. LINK LED

4. MODE LED

5. POWER LED

LOCAL REAR VIEW

Features

 Through the DVI Extender , you can use one PC to

display identical image and extension of DVI signal up
to 100 meter on DVI monitor

 Supports resolution up 1920x1200
 HDCP Compliant
 Supports Power over Cable
 Support RS-232(Bi-direction transfer)

DVI-EPLW

(Local)

 Supports all frequency band IR control
 One CAT.5 cable extension
 HD-baseT technology
 Use CAT.5 cable to install easily

Specifications

Function DVI-EPLW DVI-EPRW

DVI In Connector DVI Female x 1 None

DVI Out

Connector

RJ-45 Connector 1

IR OUT

IR2 IN None

Max. Resolution Up to 1920x1200

Cable Distance 100 m (Max.)

Power Adapter

(Min.)

Housing Metal

DVI-EPRW

(Remote)

Weight 331g 333g

Dimensions

(LxWxH)

3.5ψ Stereo Jack x 1

None DVI Female x 1

None

3.5ψ Stereo Jack x 1

DC 48V with lock None

150x80x35 mm

-1-

1. Power jack (48V DC)

2. LINK (RJ-45 Connector)

3. DVI IN

4. RS-232

REMOTE FRONT VIEW

1. IR2 IN

2. IR1 IN

3. HDCP LED

4. LINK LED

5. MODE LED

6. POWER LED

REMOTE REAR VIEW

1. LINK (RJ-45 Connector)

2. DVI OUT

3. RS-232

-2-

Installation

1. Turn off the PC and DVI monitor.

2. Connect the DVI extension cable between the PC and
the “DVI IN” port of DVI-EPLW.

3. Connect the DVI extension cable between the DVI
monitor and the “DVI OUT” port of DVI-EPRW.

4. Connect the CAT.5 cable s between the DVI-EPLW
“LINK” port and the DVI-EPRW “LINK” port of extender.

5. Connect the power cord and turn on the extender.

6. Turn on the PC and DVI monitor.

IR Receiver Cable Directions:

Put it into the DVI-EPRW “IR2 IN” port and place the IR
Receiver Cable, so that you can point to it easily with your
IR remote controller.

IR Blaster Cable Directions:

Plug IR blaster cable plug into DVI-EPLW “IR OUT” port, it
sits in front of the device receiver’s IR sensor, which is
located on the front-panel.

Additional Options

Select any additional options you may require.

1. IR Receiver Cable

GND
+V
Sig

2. IR Blaster Cable

NC
P+
N-

-3-

Technical Specifications Output Signal

Pin # Signal Pin # Signal

T.M.D.S Data 2-

1

T.M.D.S Data 2+

2

T.M.D.S Data 2/4 Shield

3

T.M.D.S Data 4-

4

T.M.D.S Data 4+

5

DDC Clock

6

DDC Data

7

Analog Vert. Sync

8

T.M.D.S Data 1-

9

T.M.D.S Data 1+

10

T.M.D.S Data 1/3 Shield

11

T.M.D.S Data 3-

12

T.M.D.S Data 3+

13

+5V Power

14

GND

15

Hot Plug Detect

16

T.M.D.S Data 0-

17

T.M.D.S Data 0+

18

T.M.D.S Data 0/5 Shield

19

T.M.D.S Data 5-

20

T.M.D.S Data 5+

21

T.M.D.S Clock Shield

22

T.M.D.S Clock+

23

T.M.D.S Clock-

24

Analog Red

C1

Analog Green

C2

Analog Blue

C3

Analog Horz Sync

C4

Analog Ground

C5

Wiring Information & Coding

Conductor

Identification

Pair 1
Pair 2
Pair 3
Pair 4

RJ45 Pin

Assignment

5 White-Blue
4 Blue
1 White-Orange
2 Orange
3 White-Green
6 Green
7 White-Brown
8 Brown

-4-

Color Code for

Conductor

Note

However sometimes, especially in demonstrations or in a
lab environment, the cable is rolled randomly in small turns
for convenience. The randomly rolled UTP cable suffers
additional signal impairments (compared to a straight cable)
and therefore the maximal operating reach might be
reduced.
Rolling a CAT5E cable around a 70cm fixed diameter
plastic drum has just a minor effect on the FEXT (Far End
Cross Talk) when compared to a fully stretched cable.

© C&C TECHNIC TAIWAN CO., LTD. All rights reserved.

Trademarks:

All the companies, brand names, and product names
referred to this manual are the trademarks or registered
trademarks belonging to their respective companies.

-5-