Avipas AV-105, AV-1050 User Manual

www.avipas.com

Model: AV-1050

HD Video Conferencing Camera

User Manual

V1.2

Please Read this User

Manual throughout before using.

1

Preface

Thanks for using this HD Video Conferencing Camera.
This manual introduces the function, installation and operation of the HD camera. Prior to installation and
usage, please read the manual thoroughly.

Precautions

This product can only be used in the specified conditions in order to avoid any damage to the camera:

 Don’t subject the camera to rain or moisture.
 Don’t remove the cover. Otherwise, you may get an electric shock. In case of abnormal operation,

contact the authorized engineer.

 Never operating under unspecified temperature, humidity and power supply.
 Please use the soft dry cloth to clean the camera. If the camera is very dirty, clean it with diluted neuter

detergent; do not use any type of solvents, which may damages the surface.

Note

This is class A production. Electromagnetic radiation at the specific frequency may affect the image quality
Of TV in home environment.

AViPAS Inc.

Address: 4300 Stevens Creek Blvd. Suite 227
San Jose, CA 95129
Phone: [phone]
Fax: [phone]
Email: [e-mail]
Website: http://www.avipas.com

2

Contents

1、 Note ··································································································3
2、 Supplied Accessories ··············································································4
3、 Quick Start ··························································································5
4、 Features ·····························································································8
5、 Product Specification ·············································································9
6、 Main Unit ························································································· 10
7、 IR Remote Controller Explanation ···························································· 11
8、 Use IR Remote Controller ······································································ 13
9、 RS-232 Interface ················································································· 16
10、 Serial Communication Control ································································ 18
11、 Menu Setting ····················································································· 32
12、 Maintains and Trouble Shooting ······························································ 37

3

Note

 Electric Safety

Installation and operation must accord with electric safety standard.

 Caution to transport

Avoid stress, vibration and soakage in transport, storage and installation.

 Polarity of power supply

The power supply of the product is +12V, the max electrical current is 2A .Polarity of the power supply plug
drawing as follows.

 Careful of installation

Do not grasp the camera head when carrying the camera. Don’t turn camera head by hand. Doing so may
result in mechanical damage.
Don’t apply in corrosive liquid, gas or solid environment to avoid damaging the cover which is made up of
plastic material.
To make sure no obstacle in rotation range.
Never power on before installation is not completed.

 Don’t dismantle the camera

We are not responsible for any unauthorized modification or dismantling.

CAUTION!

The specific frequency of electromagnetic field may affect the image of the camera!

4

Supplied Accessories

When you unpack, check that all the supplied accessories are included:

Camera ...................................... 1PCS

AC power adaptor ..................... 1PCS

Power cord .................................. 1PCS

RS232 cable ................................ 1PCS

Remote controller ........................ 1PCS

User manual .............................. 1PCS

5

Quick Start

Step1. Please check connections are correct before starting

6

Step2. Setting of the switches

Set both of the switch1 and switch2 to "OFF'. That is "Normal Working
Mode".

Step3. Setting of the system select switch
The option of video format:

VIDEO SYSTEM

0 - 8

-

1 - 9 - 2

1080i60

A - 3

1080i50

B - 4

720p60

C - 5

720p50

D

576i

6

1080p30

E

480i

7

1080p25

F

-

CAUTION:

a. After changing the switch, you need to restart the camera to take effect.

Step4. Press the Switch ON/OFF button on the rear of the camera, the power lamp light.

SW-1

SW-2

Modes

1

OFF

OFF

Normal Working Mode

2

ON

OFF - 3

OFF

ON

-

4

ON

ON

-

7

Step5. Pan-Tilt will rotate to the maximum position of top right after the camera started, then it return to the center,
the process of initialization is finished. (Note: If the position preset 0 has been stored, the position preset 0 will be
called up after initialization)

Step6. (Optional) If you want to restore the factory default settings, Press [MENU] button to display the OSD
menu. Select the item [MENU] -> [RESTORE DEFAULT] -> [Restore]. Set the value [Yes], press [HOME]
button to restore the factory default settings.

RESTORE DEFAULT

Restore Yes

Change Value
[Home] OK
[Menu] Back

8

Features

1. The camera provides a high performance in low illumination situations, particularly suitable for which

room's lighting is not very well.

2. With maximum resolution of 1920 x 1080 and output frame rate up to 30 frames / sec, this camera

provides high-definition as well as fluent video.

3. The camera video signal to noise ratio directly affects the image compression coding efficiency for

high-definition video conference terminals. The camera applies 2D and 3D noise reduction at the same
time based on motion estimation algorithm, and effectively reduces the noise.

4. 20x optical zoom.

5. Three type of video output interface: HDMI interface, HD-SDI interface,CVBS interface.

6. Infrared remote control signals pass through function. The camera is capable of receiving signal from the

infrared remote controller, and passes through to the video conferencing terminal via RS232 connector.

7. Support network port version upgrade.

9

Product Specification

Video Format

1080i/60, 1080i/50, 1080p/30, 1080p/25, 720p/60, 720p/50, NTSC, PAL

Video Output Interface

HDMI,HD-SDI,CVBS

Tilt Speed Range

1.7° ~ 69.9°/s

Sensor Type

CMOS、1/3 inch

Vertical flip &

Mirror

Support

Sensor Pixel

Effective Pixel: 2.12 million;
Total Pixel: 2.20million

Number of Preset

245

Scanning Mode

Progressive

Preset Accuracy

≤0.1°

Lens

20x, f4.42mm ~ 88.5mm, F1.8 ~
F2.8

Digital Noise

Reduction

2D&3D Digital Noise Reduction

Digital Zoom

16x

Network interface

RJ45

Minimal Illumination

0.5 Lux @ (F1.8, AGC ON)

Audio Interface

Line In/Line Out,3.5mm

Electronic shutter

1/25s ~ 1/10000s

USB Interface

USB2.0

White Balance

Auto, Indoor, Outdoor, One
Push,Manual

Input Voltage

12V DC (10.8 ~ 13.0V DC)

Backlight

Compensation

Supportable

Current

Consumption

2.0A (Max)

SNR

≥55dB

Operating

Temperature

-5°C ~ 40°C

Horizontal Angle of

View

60.7° ~ 3.36°

Storage Temperature

-20°C ~ 60°C
Vertical Angle of View

34.1° ~ 1.89°

Power

8W

Horizontal Rotation

Range

±170°

Size

142mm x 169mm x 176mm

Vertical rotation range

-30° ~ +90°

Weight

1.5Kg

Pan Speed Range

1.7° ~ 100°/s

10

Main Unit

1. Audio LINE IN Interface 8. RS232 OUT interface

2. Audio LINE OUT Interface 9. Network

3. CVBS Interface 10. HDMI Interface

4. Dip switches 11. HD-SDI Interface

5. System select switch 12. USB2.0

6. RS485 jack 13. DC 12V jack

7. RS232 IN interface 14. Power switch

11

IR Remote Controller Explanation

0. Standby Button

Press this button to enter standby mode. Press it
again to enter normal mode.
(Note: Power consumption in standby mode is
approximately half of the normal mode)

1. Position Buttons

To set preset or call preset

2. * Button

3. Set/Clear Preset Buttons
Set preset: Store a preset position

[SET PRESET] + Numeric button (0-9): Setting a
corresponding numeric key preset position
Clear preset: Erase a preset position
[CLEAR PRESET] + Numeric button (0-9)
Or: [*]+[#]+[CLEAR PRESET]: Erase all the
preset individually

4. BLC (Backlight Compensation) Button
BLC ON/OFF: Press this button to enable the

backlight compensation. Press it again to disable
the backlight compensation. (NOTE: Effective

only in auto exposure mode)
Note: If a light behind the subject, the subject will
become dark. In this case, press the backlight ON /
OFF button. To cancel this function, press the