Avionics Innovations DMP-200 Installation Manual
DMP-200 Digital Media Player
Installation Manual
Rev: E
Date: 22 June 2011
Doc Number: DMP8012-00
AVIONICS INNOVATIONS, INC.
2450 Montecito Road
Ramona, CA 92065
Phone (760) 788-2602
Fax (760) 789-7098
www.avionicsinnovations.com
Revision History
Revision Date Description By
A 26-July-06 Initial Release
Updated Installation Kit Part Numbers
Updates for V2.04 firmware
- PAUSE signal type
B 20-Oct-06
- BUSY active selection
- Test Ext Outputs
- Test Ext Inputs
Added Installation Checkout Procedure
SB
SB
C 07-Dec-06
D 24-Sep-08
-Improved behavior of external Pause for better
operation with cabin PA Systems
Added Dedicated Annunciator Mode for external
triggers
SB
SB
E 22-Jun-11 Added Instructions for Continued Airworthiness SB
DMP-200 INSTALLATION MANUAL PAGE 2 OF 18
P/N DMP8012-00 REV E
Table of Contents
REVISION HISTORY ....................................................................................................2
TABLE OF CONTENTS................................................................................................3
1. INTRODUCTION..................................................................................................5
1.1 Description ........................................................................................................................................................5
1.2 Scope .................................................................................................................................................................. 5
1.3 Installation Kit..................................................................................................................................................5
2.0 MECHANICAL.....................................................................................................6
2.1 Specifications.....................................................................................................................................................6
2.2 Mounting Considerations................................................................................................................................6
3.0 ELECTRICAL ......................................................................................................6
3.1 General...............................................................................................................................................................6
3.2 Connection to Aircraft Power ........................................................................................................................6
3.3 Inputs .................................................................................................................................................................7
3.3.1
Remote Pause/Play Button........................................................................................................................7
3.3.2
Discrete Triggers .......................................................................................................................................8
3.3.3
Dedicated Annunciators for Triggers 1, 2 and 3......................................................................................9
3.3.4
Outputs....................................................................................................................................................... 9
3.3.5
Audio..........................................................................................................................................................9
3.3.6
Discrete ......................................................................................................................................................9
3.4 Connector Pinouts..........................................................................................................................................10
DMP-200 INSTALLATION MANUAL PAGE 3 OF 18
P/N DMP8012-00 REV E
4.0 SETUP MODE ...................................................................................................11
4.1 Entering and Exiting Setup Mode...............................................................................................................11
4.1.1
Discrete Triggers 1 Through 3 – Active Level ......................................................................................11
4.1.2
External Pause – Active Level................................................................................................................11
4.1.3
External Chime Length ...........................................................................................................................11
4.1.4
Display Brightness...................................................................................................................................11
4.1.5
“LOUD” Volume Level..........................................................................................................................12
4.1.6
PLAY Screen Text..................................................................................................................................12
4.1.7
External Pause Signal Type ....................................................................................................................12
4.1.8
Configuration of the BUSY Output........................................................................................................12
4.1.9
Dedicated Annunciator Mode.................................................................................................................13
4.1.10 Test External Outputs..............................................................................................................................13
4.1.11 Test External Inputs.................................................................................................................................13
5.0 INSTALLATION CHECKOUT PROCEDURE..................................................13
6.0 TROUBLESHOOTING AND ERROR MESSAGES ........................................15
6.1 Troubleshooting..............................................................................................................................................15
6.2 Error Messages...............................................................................................................................................16
7.0 INSTRUCTIONS FOR CONTINUED AIRWORTHINESS................................17
8.0 DRAWINGS .......................................................................................................18
8.1 Mounting Configuration...............................................................................................................................18
8.2 Wiring Interconnect.......................................................................................................................................18
DMP-200 INSTALLATION MANUAL PAGE 4 OF 18
P/N DMP8012-00 REV E
1. Introduction
1.1 Description
The DMP-200 Digital Media Player is a self-contained unit which stores and replays prerecorded audio tracks. The audio tracks are encoded in “Motion Picture Expert Group
(MPEG) Level 3” format, commonly referred to as “MP3”. Audio files are stored in a
removable CompactFlash™ memory card which is prepared and installed by the user.
Audio tracks are selected via a single rotary pushbutton on the front panel of the
DMP-200. Optionally, the DMP-200 may be connected to a maximum of three external
discrete trigger inputs, each of which can be configured in software to select a particular
audio track.
The DMP-200 accepts a power input of between 10VDC and 35 VDC and provides a
single pair of ground-referenced stereo line-level audio output signals. A Mono output
which combines the Stereo line level outputs is also available.
The DMP-200 has been designed and tested to the Environmental Specifications of
RTCA DO-160E. An Environmental Qualification Form which describes the various
parameters and the levels to which they were tested is available upon request from
Avionics Innovations.
1.2 Scope
This document describes the installation and initial checkout of the DMP-200 Digital Media
Player. It may be used to support all installations, including those intended for initial Type
or Supplemental Type Certification approvals and FAA Form 337 Field Approvals.
1.3 Installation Kit
Before beginning the installation, verify that the following items are present:
Qty Part No. Description
1 20000 Digital Media Player Main Unit
1 DMP200-20 DMP-200 Installation Kit, consisting of:
1 DMP1010-00 (1ea) Mounting Tray
14046-00 (1ea) 16-pin Molex Connector
14400-00 (16ea) Molex Contacts
14073-00 (2ea) 4-40 X 3/8 Pan Head Screws
DMP057 (1ea) 256MB CompactFlash™ Memory
DMP8012-00 (1ea) DMP-200 Installation Guide
DMP8011-00 (1ea) DMP-200 Operators Guide
DMP200-01 (1ea) DMP200 Card Prep Software
1 DMP058 (OPTIONAL) USB reader/writer for
for Molex Connector
Card
CompactFlash™ cards
DMP-200 INSTALLATION MANUAL PAGE 5 OF 18
P/N DMP8012-00 REV E
2.0 Mechanical
2.1 Specifications
The DMP-200 is fully contained within a 2-inch (5cm) high standard mount
enclosure.
Height: 2.00 in. (5.1 cm)
Width: 6.25 in. (15.8 cm)
Depth*: 4.34 in. (11.0 cm)
Weight: 1.10 lb (499 g) (With Mounting Tray)
Tray depth behind panel. Connector shell protrudes 0.25” (0.64 cm)
beyond system enclosure.
2.2 Mounting Considerations
The DMP-200 should be installed in a normally heated, pressurized section of the aircraft;
however the unit contains no moving parts and does not require special vibration isolation.
The unit may be mounted in an auxiliary area of the instrument panel, in a pedestal, or
anywhere in the aircraft cabin outside of the cockpit. In a severe vibration environment,
the unit should not be mounted vertically with the front panel facing down, to ensure that
the memory card does not accidentally vibrate loose. Otherwise, the DMP-200 may be
installed in any orientation and at any angle.
3.0 Electrical
3.1 General
The following guidelines should be used when installing the DMP-200:
♦
All wiring to be installed in accordance with FAA AC-4313-1A, Chapter 11, Sect. 2
♦
All non-audio wiring to be MIL-W-22759 unless otherwise specified
♦
All audio wiring to be MIL-C-27500 shielded unless otherwise specified
3.2 Connection to Aircraft Power
The DMP-200 accepts a wide range of input voltage directly, without the need for
converters or configuration changes.
Minimum input: 10.0 VDC (1.0 Amp @ 10.0 VDC)
Maximum input: 35.0 VDC (0.1 Amp @ 35 VDC)
Nominal input: 14 VDC / 0.30 Amp
28 VDC / 0.15 Amp
Aircraft power must be supplied via a 1 Amp resettable circuit breaker.
DMP-200 INSTALLATION MANUAL PAGE 6 OF 18
P/N DMP8012-00 REV E
Loading...