AV-P2
Output Module
P/N 9310 1019 0001F Rev. 1.00
User Guide
Certifications
ETL/cETL Listed
EMC: EN 55013, EN 55020, SAA AS/NZS 1053
Conforms to: IEC 60065, EN 60065, UL 6500-2001
Certified to: CAN/CSA E60065, KETI
RoHS Status: Pb-free
Notice of Rights
All rights reserved. No part of this document may be reproduced or
transmitted in any form or by any means—electronic, mechanical,
photocopy, recording, or otherwise—without written permission of
Aviom, Inc.
Trademarks
Aviom, A-Net, the A-Net icon, Pro16, and Pro64 are trademarks of
Aviom, Inc. All other trademarks are the property of their respective
owners.
© 2007 Aviom, Inc. All rights reserved. Information subject to change
without notice.
Printed in USA
WARNING!
P
RO
Made in USA
CAUTION
Risk of electric shock!
Do Not Open
WARNING!
To reduce the risk of fire or
electric shock do not expose
this product to rain or moisture.
AVIS: Risque de choc electrique!
Ne pas ouvrir
Conceived, designed, and manufac tured by Aviom, Inc.
READ THIS FIRST
!
NO USER SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY
To reduce the risk of fire or electrical shock, do
•
not expose this product to rain or other types of
moisture.
Operating Temperature: 10˚C to 40˚C (50˚F to 105˚F)
•
CAUTION:
Using any audio system at high volume levels
•
can cause permanent damage to your hearing.
Set your system volume as low as possible.
•
Avoid prolonged exposure to excessive sound
•
pressure levels.
IMPORTANT:
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and
•
receiver.
Connect the equipment into an outlet on a circuit
•
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
Changes or modifications to the product not expressly approved by Aviom,
Inc. could void the user’s FCC authority to operate the equipment.
•
for help.
Important Safety Instructions
Read these instructions.
1.
Keep these instructions
2.
Heed all warnings.
3.
Follow all instructions.
4.
Do not use this apparatus near water.
5.
Clean only with a dry cloth.
6.
Do not block any ventilation openings. Install in accordance with
7.
the manufacturer’s instructions.
Do not install near any heat sources such as radiators, heat registers,
8.
stoves, or other apparatus (including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized or grounding-
9.
type plug. A polarized plug has two blades with one wider than the
other. A grounding-type plug has two blades and a third grounding
prong. The wide blade or third prong is provided for your safety. If
the provided plug does not fit your outlet, consult an electrician for
replacement of the obsolete outlet.
Protect the power cord from being walked on or pinched,
10.
particularly at plugs, convenience receptacles, and the point where
they exit the apparatus.
Only use attachments/accessories specified by the manufacturer.
11.
Use only with the cart, stand, tripod, bracket, or table specified by
12.
the manufacturer, or sold with the apparatus. When a cart is used,
use caution when moving the cart/apparatus combination to avoid
injury from tip-over.
Unplug this apparatus during lightning storms or when unused for
13.
long periods of time.
Refer all servicing to qualified personnel. Servicing is required
14.
when the apparatus has been damaged in any way, such as when
the power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been
dropped.
The solid line over dashed line symbol ( ) indicates that the
15.
input voltage must be a DC voltage.
The box within a box symbol ( ) indicates that the external power
16.
supply is double insulated.
Warranty Information
Aviom, Inc. Limited Warranty
Please record the following information for future reference:
Your Authorized Aviom Dealer:
Name:
Address:
Phone:
Serial Number of Your Aviom Product:
Date of Purchase:
Your Authorized Aviom Dealer is your primary source for service
and support. The information recorded above will be helpful in
communicating with your Authorized Aviom Dealer should you
need to contact Aviom Customer Service. If you have any questions
concerning the use of this unit, please contact your Authorized Aviom
Dealer first. For additional technical support, or to find the name of the
nearest Authorized Aviom Repair Station, check the Aviom website at
www.Aviom.com.
To fulfill warranty requirements, your Aviom product should be serviced
only at an authorized Aviom service center. The Aviom serial number
label must appear on the outside of the unit, or the Aviom warranty is
void.
This manual and its contents are copyrighted by Aviom, Inc. All rights
are reserved by Aviom, Inc. This document may not, in whole or in part,
be copied, photocopied, reproduced, translated, or reduced to any
electronic medium or machine-readable form without prior written
consent from Aviom, Inc.
The software and/or firmware contained within Aviom products is
copyrighted and all rights are reserved by Aviom, Inc.
Aviom, Inc. warrants this product against defects in materials and workmanship
for a period of one year from the date of the original retail purchase.
This warranty does not apply if the equipment has been damaged due to
misuse, abuse, accident, or problems with electrical power. The warranty also
does not apply if the product has been modified in any way, or if the product
serial number has been damaged, modified, or removed.
If a defect is discovered, first write or call Aviom, Inc. to obtain a Return
Authorization number. No service will be performed on any product returned
without prior authorization. Aviom, Inc. will, at its option, repair or replace the
product at no charge to you. The product must be returned during the warranty
period, with transportation charges prepaid to Aviom, Inc., 1157 Phoenixville
Pike, Suite 201, West Chester, PA 19380, USA. You must use the product’s original
packing materials for shipment. Shipments should be insured for the value of
the product. Include your name, address, phone number, description of the
problem, and copy of the original bill of sale with the shipment. The Return
Authorization number should be written on the outside of the box.
THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE
OTHER RIGHTS, WHICH VARY FROM STATE TO STATE (OR JURISDICTION TO
JURISDICTION). AVIOM’S RESPONSIBILITY FOR MALFUNCTIONS AND DEFECTS
IN HARDWARE IS LIMITED TO REPAIR AND REPLACEMENT AS SET FORTH IN THIS
LIMITED WARRANTY STATEMENT. ALL EXPRESS AND IMPLIED WARRANTIES FOR
THE PRODUCT, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN
DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE. NO WARRANTIES,
WHETHER EXPRESS OR IMPLIED, WILL APPLY AFTER SUCH PERIOD.
AVIOM, INC. DOES NOT ACCEPT LIABILITY BEYOND THE REMEDIES SET FORTH
IN THIS LIMITED WARRANTY DOCUMENT. AVIOM, INC.’S LIABILITY IS LIMITED TO
THE REPAIR OR REPLACEMENT, AT OUR OPTION, OF ANY DEFECTIVE PRODUCT,
AND SHALL IN NO EVENT INCLUDE INCIDENTAL OR CONSEQUENTIAL DAMAGES
OF ANY KIND.
SOME STATES DO NOT ALLOW EXCLUSIONS OR LIMITATION OF IMPLIED
WARRANTIES OR LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO
THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU.
Although every effort has been made to ensure the accuracy of the text
and illustrations in this manual, no guarantee is made or implied as to
the accuracy of the information contained within.
viii
ix
Table of Contents
Warranty Information . . . . . . . . . . . . . . . . . . . . vi
Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . 1
Package Contents . . . . . . . . . . . . . . . . . . . . . 1
Front Panel Components . . . . . . . . . . . . . . . . . . 2
Rear Panel Components . . . . . . . . . . . . . . . . . . 3
Compatibility . . . . . . . . . . . . . . . . . . . . . . 4
Pro16 Series Systems . . . . . . . . . . . . . . . . . . . . 5
About A-Net . . . . . . . . . . . . . . . . . . . . . . . . 5
Cables Used With A-Net Devices . . . . . . . . . . . . 6
Cat-5e Cable Lengths . . . . . . . . . . . . . . . . . . 6
System Bridge . . . . . . . . . . . . . . . . . . 7
Extending Cable Lengths . . . . . . . . . . . . . . . . 8
Cleaning and Maintenance . . . . . . . . . . . . . . . . . 8
AC Line Conditioning . . . . . . . . . . . . . . . . . . . . 8
Mounting the AV-P2 . . . . . . . . . . . . . . . . . . . . 9
Panel Descriptions . . . . . . . . . . . . . . . . . . . . . 10
AV-P2 Front Panel. . . . . . . . . . . . . . . . . . . . . . 10
Audio Output Levels . . . . . . . . . . . . . . . . . 10
Mute Switch . . . . . . . . . . . . . . . . . . . . . 10
A-Net Channel Selector . . . . . . . . . . . . . . . . 10
Stereo Pair LED . . . . . . . . . . . . . . . . . . . . 11
A-Net Active LED . . . . . . . . . . . . . . . . . . . 11
Power LED . . . . . . . . . . . . . . . . . . . . . . 11
AV-P2 Rear Panel . . . . . . . . . . . . . . . . . . . . . . 12
Power Connector . . . . . . . . . . . . . . . . . . . 12
Audio Outputs . . . . . . . . . . . . . . . . . . . . 12
A-Net Connections . . . . . . . . . . . . . . . . . . 13
Connecting Audio . . . . . . . . . . . . . . . . . . . . . 14
Wiring a Euroblock . . . . . . . . . . . . . . . . . . . . . 14
Single-conductor shielded cable . . . . . . . . 15
Two-conductor shielded cable . . . . . . . . . 15
Setting Output Levels . . . . . . . . . . . . . . . . 17
DIP Switch Settings Table . . . . . . . . . . . . 18
A-Net Connections . . . . . . . . . . . . . . . . . . . . . 19
Series Connection of A-Net Devices . . . . . . . . . . 19
Parallel A-Net Routing . . . . . . . . . . . . . . . . 19
Using an A-Net Distributor . . . . . . . . . . . 19
Extending A-Net Cable Runs . . . . . . . . . . . . . 20
Audio Networks . . . . . . . . . . . . . . . . . . . . . . 21
Digital Splits . . . . . . . . . . . . . . . . . . . . . 21
32-Channel Systems . . . . . . . . . . . . . . . . . 23
A-Net Expansion . . . . . . . . . . . . . . . . . 23
32-Channel Examples . . . . . . . . . . . . . . 24
32 Channels Send by Zero Channels Return . . . . 24
16 Channels Send by 16 Channels Return . . . . . 26
Adding More Audio Outputs . . . . . . . . . . . . . . 27
Expanding a Network with an A-Net Distributor . . 29
Specifications. . . . . . . . . . . . . . . . . . . . . . . . 30
Dimensions. . . . . . . . . . . . . . . . . . . . . . . 31
Block Diagram . . . . . . . . . . . . . . . . . . . . . 32
x
Welcome
Thank you for purchasing the Aviom Pro16™ AV-P2 Output Module.
This User Guide is designed to familiarize you with the features of your
new Pro16 product and to have you up and running in no time.
Features
The AV-P2 Output Module is designed to output a 2-channel mono or
stereo signal from a Pro16 system.
AV-P2 Output Module Features:
Two balanced line-level audio output channels
•
Individual output levels for each channel
•
Audio output level DIP switches
•
Euroblock terminal block audio connections
•
Dual mono or stereo output
•
Rotary A-Net channel selector
•
Audio mute switch
•
RJ45 A-Net® input and output
•
Removable, reversible mounting flanges
•
Remote power over A-Net by using the A-16D or
•
A-16D Pro A-Net Distributor
Package Contents
Check the contents of the shipping box carefully before making
connections and continuing with installation.
The contents of the AV-P2 Output Module box include:
One AV-P2 Output Module
•
Mounting flanges
•
One DC power supply for the AV-P2
•
User Guide
•
1
2
3
Front Panel Components Rear Panel Components
LEFT
RIGHT
MUTE
CHANNEL
STEREO
PAIR
A-NET
ACTIVE
POWER
AV-P2
OUTPUT LEVELS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ON
LEFT
DC
POWER
RIGHT
OUT
IN
AUDIO OUTPUT
AV-P2
+ – + –
18-24 VDC
500mA
x y z
v w
w x
1. Output Level DIP Switches
2. Audio Mute Switch
3. A-Net Channel Selector
4. Stereo Pair LED
5. A-Net Active LED
6. Power LED
7. Reversible Mounting Flanges
1. DC Power Connector
2. Audio Output Euroblock Connectors
3. A-Net Out Port
4. A-Net In Port
v
Compatibility
The AV-P2 Output Module can be used with the following Aviom Pro16
products:
AN-16/i Input Module
•
AN-16/i-M Mic Input Module
•
AV-M8 Mic Input Module
•
Aviom16/o-Y1 A-Net card for use with Yamaha®
•
consoles
D-16c A-Net card for use with DiGiCo® consoles
•
A-16R Personal Mixer
•
A-16II Personal Mixer
•
A-16D A-Net Distributor
•
A-16D Pro A-Net Distributor
•
AN-16/o Output Module
•
AN-16SBR System Bridge
•
A-16T Transmitter (discontinued)
•
A-16 Personal Mixer (discontinued)
•
In addition to the Aviom devices mentioned above, the AV-P2 Output
Module can be connected to third-party devices that support Pro16
A-Net technology.
The AV-P2 Output Module can also be used with Aviom Pro64™ systems
when connected to the Pro64 ASI A-Net System Interface.
4
Pro16 Series Systems
A complete Pro16™ Series audio network system consists of at least
one Pro16 input module connected to at least one Pro16 output device
such as the AV-P2 Output Module, AN-16/o Output Module, or A-16II
Personal Mixer. Many configurations are possible by using additional
input modules and/or Personal Mixers and output modules.
About A-Net
Aviom’s A-Net® is a high-speed data transmission protocol. It is capable
of sending and receiving uncompressed, high-quality audio using
readily available Category 5 cables. A-Net technology is a proprietary
system developed by Aviom.
A-Net is based on Ethernet, a Local Area Network (or LAN) technology.
This provides A-Net with a mature and robust base on which to build.
However, because A-Net manages data in a way that ensures optimum
performance for audio, Aviom products are not compatible with offthe-shelf computer products designed for Ethernet networks such as
hubs and switches.
As implemented in the Pro16 Series products, the A-Net signal carries
sixteen channels of digital data from a Pro16 input module to a Pro16
network device or output device, such as the AN-16/o Output Module or
A-16II Personal Mixer.
Some of the benefits of using A-Net to transmit digital audio are:
Virtually no latency
•
No ground loops
•
Easy cabling using readily available components
•
Easy expansion and reconfiguration of systems
•
An unlimited number of A-Net devices can be used in
•
a system
Long distances between system components
•
P Note: While the Category 5 connectors and cables used with
your Aviom products look like typical computer network
connections, do not connect computers, routers, or other
home and business networking equipment to your Aviom
products.
5
6
7
Pro16 Input
Pro16 Output
Total A-Net cable length can be 500 feet (150 meters)
System Bridge
A-Net Out
A-Net In
System
Bridge
Cables Used With A-Net Devices
All Cat-5e connections between A-Net devices should use Unshielded
Twisted Pair (UTP) cable. The cable can be of the stranded or solid type;
solid wire performs better over long distances, while stranded wire is
more flexible and easier to manipulate and therefore easier to work
with in a performance situation.
Cables designated as Cat-5e in this User Guide can be interchanged with
any Cat-6 (or better) cable. Cables will be referred to simply as “Cat-5e.”
Connectors on Cat-5e cables can be of the standard RJ45 variety or
locking Neutrik® EtherCon® type.
P Note: When purchasing Category 5e cables, be sure to buy only
standard Cat-5e cables, not those sold as crossover cables.
A crossover cable is used for file transfer between two
computers. A crossover cable is not compatible with your
Aviom equipment.
Cat-5e Cable Lengths
Category 5e cables used with your Aviom products can be up to 500
feet (approximately 150 meters) in length. The maximum cable length
specification applies to the cable connected between the Pro16 input
module and the first A-Net device (AV-P2, AN-16/o Output Module,
Personal Mixer, etc.), as well as for cable runs between each additional
A-Net compatible device in your system.
Pro16 Input Module
Up to 500 feet
of Cat-5e cable
can be used to
connect
each system
component
Pro16 Output Modules,
A-Net Distributors, or
Personal Mixers
Infinite
number
of A-Net
components
This diagram shows a Pro16 input module connected to compatible
Pro16 devices. Each cable shown can be up to 500 feet in length.
Your cable length performance will be affected by a number of factors
,including the quality of the cables used and the number of devices
such as cable couplers or wall panel interconnections in use. Use Cat-5e
or higher cables for best performance wherever possible.
For cable runs in excess of 500 feet between A-Net devices, fiber optic
media converters can be used.
System Bridge
In systems using the optional AN-16SBR System Bridge, the cable length
specification applies to the total cable length between the A-Net devices
being connected and the AN-16SBR components.
The maximum c able length calculation includes any cables used to
connect Pro16 devices to a Sys tem Bridge.
8
9
Extending Cable Lengths
Cat-5e cables can be extended by using a simple passive device called
an inline coupler to add length to existing cables (as long as you do not
exceed the specified maximum cable length). If you need a longer cable
on occasion, this is a simple solution. Note that it is possible that the
maximum cable length specification can be compromised by using
inline couplers or other passive cable connection devices.
For long cable runs (in excess of 500 feet), any Pro16 device can be used
to extend the distance between two points. Each Pro16 device refreshes
the A-Net signal, allowing another 500 feet of cable to be used.
Cleaning and Maintenance
The exterior of your Aviom products should be cleaned with a dry, soft,
lint-free cloth. For tougher dirt, you can use a cloth slightly dampened
with water or with a mild detergent.
When cleaning your Aviom products, never spray cleaners directly onto
the product surfaces. Instead, spray a small amount of the cleaning
solution onto a clean cloth first. Then use the dampened cloth to clean
the product.
P Note: Never use solvents or abrasive cleaners on the finished
surfaces of your Aviom products.
Mounting the AV-P2
The AV-P2 module is designed to be mounted to any flat surface.
Optionally, it can be rack mounted using a standard 19-inch rack shelf.
Two AV-P2 units can fit on a single rack shelf.
The mounting flanges on each side of the device are designed to
support the weight of the AV-P2 without additional hardware. The
mounting flanges can be reversed easily using only a Phillips head
screwdriver. Each mounting flange contains holes for two screws per
side. Always support the unit with all four screws when attaching the
product to a flat surface.
If desired, the mounting flanges can be turned around so that they
mount under the AV-P2, making the profile of the AV-P2 as small as
possible. Always use all the mounting screws when reversing the flanges
on the AV-P2.
Always allow adequate ventilation for devices mounted in equipment
racks. Avoid placing your AV-P2 directly above or below other rackmounted devices that produce high levels of heat, such as power amps.
AC Line Conditioning
Aviom products are digital devices and as such are sensitive to sudden
spikes and drops in the AC line voltage. Changes in the line voltage
from lightning, power outages, etc., can sometimes damage electronic
equipment.
To minimize the chance of damage to your equipment from sudden
changes in the AC line voltage, you may want to plug your equipment
into a power source that has surge and spike protection. Power outlet
strips are available with built-in surge protection circuits that may help
protect your equipment.
Other options for protection of your equipment include the use of an
AC line conditioner or a battery backup system (sometimes referred to
as an uninterruptible power supply, or UPS).
10
11
Panel Descriptions
LEFT
RIGHT
MUTE
CHANNEL
STEREO
PAIR
A-NET
ACTIVE
POWER
AV-P2
OUTPUT LEVELS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ON
STEREO
PAIR
A-NET
ACTIVE
POWER
AV-P2
stereo signal from the Pro16 A-Net stream connected to the AV-P2 via
its A-Net In port.
This section explains the basic layout of the front and rear panels of your
new Aviom product. The diagrams on the previous pages can be used
as a quick visual guide to the location of the components of the AV-P2
mentioned in this section.
AV-P2 Front Panel
The front panel of the AV-P2 contains the Output Level DIP switches,
Mute switch, A-Net Channel Selector knob, and LED indicators for Stereo
Pair, A-Net Active, and Power.
The AV-P2 front panel interface
Audio Output Levels
Individual DIP switches are provided for left and right channel audio
output levels. The top of the AV-P2 case includes a handy output level
chart. Move a DIP switch to the up position to activate it.
The Channel Selector provides mono or stereo output signals based on
the settings of the Pro16 network’s input module’s Stereo Link switches.
P Note: The left and right audio channels have separate output level
settings. When using mono A-Net channels, this allows two
different output levels to be set if desired.
Stereo Pair LED
The Stereo Pair LED will light whenever the Channel Selector knob is
positioned on either channel that makes up a left/right stereo pair (as
set by the network’s input module).
For example, if A-Net channels 3 and 4 are stereo linked in the network,
moving the AV-P2 Channel Selector knob to either position 3 or 4 will
produce the same result: the Stereo Pair LED will light, A-Net channel
3 is assigned to the AV-P2 left audio output, and A-Net channel 4 is
assigned to the AV-P2 right output.
The Stereo Pair, A-Net Ac tive, and Power LED indicators
Mute Switch
The Mute switch provides an easy way to turn the audio output of
the AV-P2 off temporarily without having to change the output level
settings. Use it when making audio connections to other devices,
changing cable routings, etc. Move the switch to the left to mute the
AV-P2 audio output and to the right for normal operation.
A-Net Channel Selector
The AV-P2 can output single channel, dual mono, or stereo audio
signals. The rotary channel selector knob is used to select a mono or
A-Net Active LED
Whenever a valid A-Net signal is connected to the AV-P2 via the A-Net In
port, the A-Net Active LED will light.
Power LED
The Power LED lights whenever the AV-P2 DC power supply is connected
to a valid AC power source, or when it is receiving power over the
Cat-5 connection. It does not, however, indicate that a valid A-Net digital
stream is being received. That is the job of the A-Net Active LED.
12
13
AV-P2 Rear Panel
LEFT
DC
POWER
RIGHT
OUT
IN
AUDIO OUTPUT
AV-P2
+ – + –
18-24 VDC
500mA
OUT
IN
AV-P2
The rear panel of the AV-P2 Output Module contains the DC power
connector, the left/right audio output Euroblock connections, and the
A-Net connections.
The outputs on the AV-P2 use 5.0 mm Euroblock connectors, and can
be connected to balanced or unbalanced audio devices. Male Euroblock
jacks are provided.
Euroblock connectors plug into the socket s on the AV-P2 panel.
The AV-P2 rear panel inter face
Power Connector
The AV-P2 Output Module comes with an external DC switching-type
power supply. This type of power supply can be used worldwide with
a wide range of AC wall current output voltages (100-240VAC). When
traveling, you do not need to replace the power supply in countries
where voltages are different. You may, however, need plug adapters
to allow the power supply to be connected to wall outlets in some
countries, since many countries use different physical plug layouts for
their power systems.
If a replacement power supply is required, always choose a power supply
with equivalent specifications: 18-24 VDC, 500mA, center pin positive.
Audio Outputs
Audio outputs on the AV-P2 are provided via locking Euroblock
connectors. Each channel’s output level can be set individually using
the DIP switches on the front panel.
The Euroblock plugs can be connected using only a small flat-blade
screwdriver.
A-Net Connections
Two A-Net connections are provided on the rear panel of the AV-P2
Output Module. There is one A-Net In port and one A-Net Out port.
The A-Net In port receives digital data in Aviom’s proprietary A-Net
format. The A-Net Out port is used to pass incoming A-Net data to
additional A-Net compatible devices in a system. The A-Net Out port
will always transmit the full 16-channel A-Net stream regardless of the
settings on the AV-P2.
The AV-P2 rear-panel A-Net connections
14
15
Connecting Audio
LEFT
RIGHT
OUT
IN
AUDIO OUTPUT
AV-P2
+ – + –
The audio outputs on the AV-P2 Output Module can be connected to
balanced or unbalanced devices via the Euroblock jacks.
Wiring a Euroblock
Euroblock connectors provide an easy, solder-free way of making audio
connections between the AV-P2 and other audio components. Only a
small flat-blade screw driver is required to make connections. For extra
strength, you can add solder to each bare wire on an audio cable to stop
the wire strands from unwinding (called “tinning”).
AV-P2 left/right Euroblock audio outputs
Connecting to a Balanced Device
To connect the AV-P2 Euroblock audio output to a device that can
accept a balanced line-level input:
1.
Strip the insulating jacket of the cable back about .75
inch (18 mm) to reveal the individual hot, cold, and
ground wires within.
2.
Remove a small amount of each individual wire’s
insulation (approximately .25 inch, 6 mm).
3.
On the 5.0 mm Euroblock male plug, use a small screw
driver to loosen and open the sockets that will receive
the individual wires.
4.
Insert the individual hot (+), cold (-), and ground wires
into the matching sockets on the Euroblock plug.
5.
Tighten the screws on the wire sockets to secure the
individual wires.
6.
Plug the completed Euroblock plug into the desired
output channel on the AV-P2.
7.
Connect the AV-P2 to your audio device.
The Eurobloc k plug, showing the screws that hold the individual wires
in place (lef t-to-r ight), hot (+), cold (-), and ground
Connecting to an Unbalanced Device
The AV-P2 audio outputs can be connected to unbalanced audio
devices; connections can use single-conductor or two-conductor
shielded cable.
Single-conductor shielded cable
To connect the AV-P2 audio output to an unbalanced line-level device
using single-conductor shielded cable:
Strip the insulating jacket of the cable back about .75
1.
inch (18 mm) to reveal the individual hot and ground
wires within.
Remove a small amount of each individual wire’s
2.
insulation (approximately .25 inch, 6 mm).
On the Euroblock plug, use a small screw driver to
3.
loosen and open the sockets that will receive the
individual wires.
Insert the audio cable’s hot (+) wire into the matching
4.
socket on the Euroblock plug.
Insert the audio cable’s ground wire into the matching
5.
socket on the Euroblock plug. The cold (-) socket on
the Euroblock remains unused in this configuration.
Tighten the screws on the wire sockets to secure the
6.
individual wires.
Plug the completed Euroblock plug into the desired
7.
output channel on the AV-P2.
Connect the completed cable to your audio device.
8.
Two-conductor shielded cable
To connect the AV-P2 audio output to an unbalanced line-level device
using two-conductor shielded cable:
16
17
Strip the insulating jacket of the cable back about .75
LEFT
RIGHT
MUTE
CHANNEL
STEREO
PAIR
A-NET
ACTIVE
POWER
AV-P2
OUTPUT LEVELS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
ON
1.
inch (18 mm) to reveal the individual hot and ground
wires within.
Remove a small amount of each individual wire’s
2.
insulation (approximately .25 inch, 6 mm).
On the Euroblock plug, use a small screw driver to
3.
loosen and open the sockets that will receive the
individual wires.
Insert the audio cable’s hot (+) wire into the matching
4.
socket on the Euroblock plug.
Insert the audio cable’s cold (-) wire into the matching
5.
socket on the Euroblock plug.
Insert the audio cable’s ground wire into the matching
6.
socket on the Euroblock plug.
Tighten the screws on the wire sockets to secure the
7.
individual wires.
Plug the completed Euroblock plug into the desired
8.
output channel on the AV-P2.
At the other end of the cable, connect the hot (+) wire
9.
to the unbalanced device’s hot connector.
Connect the cold (-) and ground wire to the unbalanced
10.
device’s ground connector.
Connect the completed cable to your audio device.
11.
Setting Output Levels
Output levels on the AV-P2 are set with the DIP switches on the front
panel. Individual settings are possible for the left and right audio
channels.
The AV-P2 front panel interface
To temporarily mute the output of the AV-P2 while adjustments are
being made, move the Mu te switch to the left.
Plug the completed Euroblock connectors into the AV-P2 audio output
jacks.
OUTPUT LEVEL SETTINGS
1 1 1 1 1 1 0.0 0 0 1 1 1 1 -19.0
1 1 1 1 1 0 -1.2 0 0 1 1 1 0 -20.2
1 1 1 1 0 1 -2.9 0 0 1 1 0 1 -21.8
1 1 1 1 0 0 -4.6 0 0 1 1 0 0 -23.6
0 1 1 1 1 1 -5.7 0 0 0 1 1 1 -25.5
0 1 1 1 1 0 -6.9 0 0 0 1 1 0 -26.7
1 2 3 4 5 6
DIP Switch Settings Table
The following table lists the DIP switch settings for the AV-P2 left/right
output levels. In the output levels table, “0” indicates the down position
and “1” indicates the up position on the DIP switch.
DIP Switch Setting
1 2 3 4 5 6
1 1 1 1 1 1 0
1 1 1 1 1 0 -1.2
1 1 1 1 0 1 -2.9
1 1 1 1 0 0 -4.6
0 1 1 1 1 1 -5.7
0 1 1 1 1 0 -6.9
0 1 1 1 0 1 -8.6
0 1 1 1 0 0 -10.3
0 1 0 1 1 1 -12.9
0 1 0 1 1 0 -14.1
0 1 0 1 0 1 -15.8
0 1 0 1 0 0 -17.5
0 0 1 1 1 1 -19.0
0 0 1 1 1 0 -20.2
0 0 1 1 0 1 -21.8
0 0 1 1 0 0 -23.6
0 0 0 1 1 1 -25.5
0 0 0 1 1 0 -26.7
0 0 0 1 0 1 -28.4
0 0 0 1 0 0 -30.2
0 0 0 0 1 1 -31.5
0 0 0 0 1 0 -32.8
0 0 0 0 0 1 -34.4
0 0 0 0 0 0 -35.9
The output level table is also printed on the top of the AV-P2 case for
quick reference.
18
LEVEL (dB)
A-Net Connections
A-Net
In Out
A-Net
In Out
A-Net
In Out
A-Net
In Out
When creating a Pro16 A-Net system, the simplest connection method
uses what is called a daisy chain. That is, each A-Net device is connected
in series. The first device in the chain receives its A-Net signal from
the AV-M8 Mic Input Module’s A-Net Out port. Each successive A-Net
compatible device gets its A-Net connection from the A-Net Out port of
the device preceding it in the daisy chain.
There is one drawback to this connection method, however. If one
A-Net device in the daisy chain is disconnected from the A-Net signal
chain, all units beyond that point will not output any audio until the unit
is reconnected to a valid A-Net source.
Series Connection of A-Net Devices
In this diagram, A-Net is connec ted from device to device using Cat-5e
cables. The A-Net Out por t on the rst device connects to the A-Net In
port on the next, and so on.
Parallel A-Net Routing
A parallel A-Net connection eliminates the need to daisy chain
A-Net devices together. By using the optional A-16D or A-16D Pro
A-Net Distributor, parallel A-Net connections are possible. In fact, any
combination of series and parallel connections can be used to solve
even the most complex audio routing problems.
Using an A-Net Distributor
Any Pro16 A-Net Distributor can be connected to the A-Net Out port
of a Pro16 device. In the diagram below, a variety of A-Net compatible
components are shown connected in parallel to an A-16D A-Net
Distributor.
19
20
21
AV-M8
8 Channels In
AV-P2
Mono/Stereo Out
A-Net, up to 500 feet
A-16D
A-Net Out
A-Net Out (x8)
A-Net In
A-Net In
Pro16 Input
AV-P2 AN-16/o A-16R
A-16II
A-Net Out from the Pro16 input module connec ts to an A-Net
Distributor and then up to eight parallel streams can connec t
additional Pro16 produc ts.
Audio Networks
Pro16 A-Net input and output modules can be combined to create audio
networks of up to 64 audio channels with unlimited expansion.
8-Channel Systems
The most basic A-Net based system uses one input module connected
to one output module or Personal Mixer. For example, the AV-M8 can
be connected to an AV-P2 Output Module to deliver eight discrete linelevel audio signals to powered speakers, recording devices, mixers, etc.
The A-Net signal from the A-16D Distributor is connected to each A-Net
compatible device with a Cat-5e cable. Removing one A-Net device has
no effect on the other A-Net components being used.
P Note: The A-16D Pro Distributor can also be used in this
Extending A-Net Cable Runs
To span distances longer than the maximum specified for a single A-Net
cable (500 feet, 150 meters), the A-16D (or A-16D Pro) A-Net Distributor
can be used as a signal repeater. Simply insert the A-16D or A-16D Pro
into the A-Net stream at the 500-foot point and the A-Net signal will be
refreshed. Another 500 feet/150 meters of cable can then be added. This
process can be repeated as many times as required to extend cables. In
fact, any Pro16 device will refresh the A-Net signal and allow another
500-foot cable run between it and the next Pro16 device.
For long distance applications, fiber optic cable can be used to span
distances up to 50 miles (80 km) with the use of devices called media
converters. A media converter changes the Cat-5 Ethernet-based A-Net
signal to a fiber optical signal at the source location and then back to
Cat-5 at the destination. Several companies make media converters
that can be used with your Aviom equipment. Both single and multimode fiber devices can be used. Refer to the Aviom website for a list of
approved devices.
configuration. It supplies DC power over the Cat-5e cable to
compatible Pro16 devices.
Connect A-Net Out on the AV-M8 to the A-Ne t In on any compatible
device. The eight audio channels from the AV-M8 appear as channels
1-8 on the output module.
16-Channel Systems
Any Pro16 input module can be substituted for the AV-M8 shown in
the diagram above. This includes the AN-16/i, AN-16/i-M, Y1 and D-16c
A-Net cards. These Pro16 devices provide 16 channels to the AV-P2.
Digital Splits
A-Net allows far more flexibility than just the simple configuration
outlined above. In fact, any number of Pro16 A-Net devices can be
connected to a single input module. This allows the creation of infinite
numbers of digital signal splits, with each additional A-Net device
capable of being located up to 500 feet (150 meters) away.
Splits can be used to send exact digital copies of the audio signals
from the input module to a live sound mixing console, a recording
system, an audio machine room, and a live television broadcast facility
simultaneously with no signal degradation. To add digital copies, or
“splits,” to a system, simply connect an A-Net Out to the A-Net In on
Pro16 output modules or Personal Mixers. The following diagram shows
one such system using a variety of Pro16 devices connected in series.
22
23
EXPANSION OUT
IN
AV-M8
CH 9-16
OUT
ADAT
®
Pro16 Input
16 Channels In
AN-16/o
Up to 16 Channels Out
2 Channels Out
2 Channels Out
2-Channel Mix Out
AV-P2
A-16II
A-Net, up to 500 feet,
150 meters
...to teleconferencing
head end
...to stereo recording device
...to powered speakers
...to headphones
AV-P2
One Pro16 input module is shown connected to four A-Net devices. The
AN-16/i, AN-16/i-M, AV-M8, Y1 card, or D -16c card can be subs tituted
for the Pro16 input module shown in the diagram.
When substituting an AV-M8 module in the diagram above, remember
that the AV-M8 is an 8-channel device. In the configuration above,
only channels 1-8 on the Pro16 output devices will have audio signals
present. Cascading two AV-M8 modules with the ADAT® link will provide
16 channels.
32-Channel Systems
Aviom’s Pro16 audio networking products work in blocks of 16 channels.
Audio networks of 32 channels can be configured as:
32 channels send by zero channels return (32 x 0 )
•
16 channels send by 16 channels return (16 x 16)
•
0 channels send by 32 channels return (0 x 32)
•
Systems up to 32 audio channels can be configured with no additional
hardware by using the built-in A-Net Expansion ports.
For systems larger than 32 channels, Aviom offers the AN-16SBR System
Bridge as an option. The System Bridge allows up to four A-Net streams
to be combined into a single Cat-5e cable for distribution over long
distances.
A 32-channel system is comprised of two pair of Pro16 Series I/O units,
each providing a 16-channel data stream. (Remember that two AV-M8
units cascaded via the ADAT link create a single Pro16 A-Net stream.)
Since the Pro16 system is modular, you can connect the Pro16 Series
units as needed, making any of the configurations mentioned previously
available at any time. Simply move and re-patch the units.
A-Net Expansion
In a 32-channel system, the A-Net Expansion port is used to allow two
A-Net data streams to travel down one cable.
The rear panel of the AV-M8 showing the A-Net Out and A-Net
Expansion ports
Some points to remember about using the A-Net Expansion ports on
the Pro16 Series input and output modules to create an audio network:
When creating a network with two pair of Pro16 Series
•
units, one A-Net Expansion port will be connected to
an A-Net In port while the other A-Net Expansion port
24
25
Pro16 Output
Channels 1-16 In Channels 1-16 Out
Channels 17-32 In Channels 17-32 Out
A-Net
A-Net Expansion
Audio channels 17-32
Audio channels 1-16
Pro16 Output
Pro16 Input
Pro16 Input
will be connected to an A-Net Out port.
The A-Net Out ports on the Pro16 output modules
•
should be empty when only four Pro16 Series units are
being used to create a network. These ports are then
available for adding audio splits with additional Pro16
output modules, or for connecting to a Personal Mixer
product such as the A-16II or A-16R.
The cable connecting the two halves of the network
•
(carrying 32 channels of audio) should be connected
to one A-Net In port and one A-Net Out port.
Do not connect Cat-5e cables carrying expanded
•
system data (more than 16 channels) to an A-Net
Distributor or Personal Mixer product.
The maximum cable length specification of 500 feet
•
(150 meters) applies to the length between an A-Net
In port and an A-Net Out port. Cables used to connect
devices via the A-Net Expansion ports must fall within
this maximum distance.
An A-Net Expansion port is never connected to another
•
A-Net Expansion port.
The A-Net Main Out on the AN-16/i-M Mic Input
•
Module is the only A-Net port that works with the
Expansion port. The A-Net Aux output carries only
local data.
32-Channel Examples
In the following examples, any Pro16 input module can be used. This
includes the AV-M8, Y1 console interface card (for Yamaha products),
D-16c console interface card (for DiGiCo products), AN-16/i, or the
AN-16/i-M. Only one device is shown in the illustrations. They are
referred to generically as “Pro16 input modules.”
A pair of AV-M8 units cascaded via the ADAT link are shown in the
diagram as a single input module.
32 Channels Send by Zero Channels Return
The 32 x 0 configuration has 32 audio inputs on one side of the audio
network and 32 audio outputs on the other side.
With this configuration, up to 32 analog audio (mic- or line-level) signals
are connected as inputs to two Pro16 input modules. One input module
contains channels 1-16, while the other has channels 17-32.
Two Pro16 input modules congured as 32 x 0
Two Pro16 output devices are connected on the receive side of the
audio network. In the diagram, any Pro16 output device can be used.
This includes A-16II and A-16R Personal Mixers, as well as AN-16/o and
AV-P2 output modules.
To configure a 32 x 0 system:
Connect the first 16 mic- or line-level audio sources to
1.
inputs 1-16 on the first Pro16 input module.
Connect the second group of 16 audio sources to
2.
inputs 1-16 on the second Pro16 input module.
Connect a Cat-5e cable from the A-Net out port on the
3.
first input module to the A-Net expANsioN port on the
second input module.
Connect a cable from the A-Net out port on the second
4.
Pro16 Series input module and run it to the destination
where the Pro16 output modules are located. Plug it
into the A-Net iN port on the first output module.
Connect a Cat-5e cable from the A-Net expANsi oN port
5.
on the first output module to A-Net iN on the second
output module.
Patch the audio outputs from the two output modules
6.
into the desired destinations.
Remember that the maximum cable length between A-Net devices is
500 feet (150 meters). Always use Cat-5e UTP cable.
The diagram that follows shows a pair of 16-channel Pro16 input
modules used for audio input channels 1-16 and 17-32, connected to a
pair of output modules.
26
27
Channels 1-16
Channels 17-32
EXPANSION OUT
EXPANSION OUT
EXPANSION OUT
EXPANSION OUT
Channels 17-32 in
A
-N
e
t
A-Net Expansion
Pro16 Output
Pro16 Input
Pro16 Output
Pro16 Input
Channels 1-16 In Channels 1-16 Out
Channels 17-32 InChannels 17-32 Out
Channels 17-32 out
Channels 1-16 in
Channels 1-16 out
Note that A-Net In is connected to A- Net Out on both pairs of modules
in this 32 x 0 system.
The AV-P2 can be substituted for the output module that supplies
channels 17-32 if desired. It cannot be substituted for the output module
supplying channels 1-16 because the AV-P2 does not have the A-Net
Expansion port.
16 Channels Send by 16 Channels Return
The 16 x 16 configuration has 16 inputs and 16 outputs on each side of
the audio network.
Using this configuration, each side of the audio network has one input
module and one Pro16 output module. Sixteen channels of audio move
in each direction over a single Cat-5e cable.
The AV-P2 can be used to output channels 17-32 in this diagram. It
cannot be substituted for the output module supplying channels 1-16
because the AV-P2 does not have the A-Net Expansion port.
Again, the A-Net Expansion port is used to combine the A-Net data from
two devices for transmission over one Cat-5e cable.
To configure a 16 x 16 system:
Set up one input module (AV-M8, pair of AV-M8s, Y1
1.
card, AN-16/i or AN-16/i-M) and one output module on
each side of the network.
Connect 16 mic- or line-level audio sources to inputs
2.
1-16 on the first Pro16 Series input module.
Connect a Cat-5e cable from the A-Net out port on the
3.
first input module to the A-Net expANsioN port on the
first output module.
Plug a Cat-5e cable into the A-Net iN port on the first
4.
output module. This cable will be used to span up
to 500 feet/150 meters between the two sides of the
network.
Connect the cable from the A-Ne t iN port in Step 4 to
5.
the A-Net out port on the second Pro16 Series input
module.
Connect the second group of 16 audio sources to
6.
inputs 1-16 on the second Pro16 Series input module.
Connect a Cat-5e cable from the A-Net expANsi oN port
7.
on the second input module to A-Net iN on the second
Pro16 output module.
Patch the audio outputs from the two output modules
8.
into the desired destinations.
Adding More Audio Outputs
As mentioned previously, the A-Net Out ports on AN-16/o and AV-P2
output modules and Personal Mixer products remain available even
28
29
when creating a bidirectional audio network. This allows additional
Channels 1-16 In
Channels 1-16 Out
Channels 17-32 Out
Channels 17-32 In
Channels 17-32 Out
Channels 17-32 Out
Channels 17-32 Out
A-Net
A-Net Expansion
Channels 1-16 Out
Channels 1-16 Out
Channels 1-16 Out
Audio channels 17-32
Audio channels 1-16
Pro16 Input
Pro16 Input
Pro16 Output
Pro16 Output
Pro16 Output
Pro16 Output
Pro16 Output
Pro16 Output
Pro16 Output
Pro16 Output
output modules to be added as needed to suit a variety of audio
situations. Any Pro16 A-Net compatible product with an A-Net In can be
connected to an A-Net Out port. This flexible routing scheme allows you
to send audio to a variety of different locations and to include Aviom’s
Pro16 Monitor Mixing System for mic applications.
to add is connected by patching a Cat-5e cable from
A-Net ou t to the new module’s A-Net iN port.
Use AN-16/o or AV-P2 output modules as required by
•
your application.
Expanding a Network with an A-Net Distributor
While the A-16D and A-16D Pro Distributors are not compatible with the
data being distributed via the A-Net Expansion ports, you can use an
A-16D to add wiring flexibility to your system.
As mentioned in the previous examples, an A-Net Distributor can be
connected to any single A-Net Out port to allow parallel distribution of
up to eight exact copies of the input data.
The total cable length between A-Net devices is limited to 500 feet, 150
meters.
Digital copies of each 16-channel output stream have been added.
In this example, a 16 x 16 network has been expanded to include three
additional Pro16 output modules on each side of the network. You can
use any combination of the AN-16/o or AV-P2 output modules.
Each output module is connected via A-Net using a Cat-5e cable.
Remember that the cable lengths between each A-Net device can be up
to 500 feet (150 meters) long.
To create an expanded network:
First start by configuring the network according to
•
your basic needs (either as 32 x 0, or as 16 x 16).
Add additional Pro16 output modules by connecting
•
a Cat-5e cable from the A-Net out port on one of the
connected modules to the A-Net iN port on a Pro16
output module that you want to use to expand the
system.
Each additional Pro16 output module that you want
•
30
31
Specifications
Audio Output s 2, impedance balanced line-level
5.0 mm Euroblock connec tors, female, panel-mount
2 male Euroblock conne ctors supplied in box
Screw te rminals: Audio +; Audio -; Ground
Channel Selection 16-positi on rotar y switch
D/A Conversion 4 8kHz, 24-bit
Output Levels Variable: +4dBu to -31dBu in 1.5dB increments
6-position DIP switch, per channel
Indicator s LEDs; red: Power, green: A-Net Active,
Output Impe dance 100 ohms
Signal to Noise
(unweighted)
Freq. Response 4Hz–22kHz +0.2dB/-3dB
THD +N -93dB at -10dBFS
Crosstalk -85dB at 1kHz
Bit Error Rate (BER) 10
Digital Connections A-Net In: 1; A-Net Out: 1; RJ45 connect ors
Pro16™ A-Net
Latenc y 0.880 msec (measured from anal og input to
Power Supply
Input Voltage
Output Voltage
Plug Size
Dimension s 7.45” (189.2 mm) wide x 7” (177.8 mm) deep; 1U high
Weight 3.4 lbs (1.54 kilo)
yellow: Stere o Pair
93dB typic al, A/D to D/A
Measured from AN-16/i Input Modul e to AV-P2
-12
®
Uses unshielded Cat-5e UTP (or better) cable
analog output)
External, DC, univer sal switching type
100–240 volts, 50/60Hz, 30VA
18–24 VDC, 0.5 amp
2 mm, locking, center pin hot
Dimensions
All Aviom products are designed and manufactured in the USA .
Block Diagram
Channel
select
Audio Output L/R
Euroblock
A-Net
D/A
converter
Level control
+4dBu to -31dBu, 1.5dB steps
Mute
Audio Out
+
_
32
Aviom Warranty Registration
Please take a moment to fill in this warranty registration form. Return it to
Aviom via mail or fax. All information will be kept confidential.
Model Number Serial Number
Model Number Serial Number
Model Number Serial Number
Model Number Serial Number
Date Purchased
Dealer Name
Dealer Location
Your Name
Address
Address
City
State/Province
Zip/Postal Code
Country
Email Address
Fax this form to Aviom at +1 610-738-9950.
34
35
Index
Symbols
+48 Volt 2
16-Channel Systems 21
32-Channel Systems 23
8-Channel Systems 21
A
A-16D 4
A-16D Distributor 19, 20, 29
A-16D Pro 4, 20
A-16D Pro Distributor
A-16II 4, 5, 25
A-16R
A-16T 4
A-Net 5, 21, 28
A-Net, long distance
A-Net Active LED 2, 11
A-Net Channel Selector 10
A-Net connections 12
A-Net Distributors
A-Net Expansion
A-Net In 13
A-Net Out 13, 25, 27
A-Net signal repeater 20
AC current
AC Line Conditioning
ADAT 2
Adding More Audio Outputs 27
Adding Personal Mixers 28
AN-16/i
AN-16/i-M
AN-16/o 4, 5, 25
AN-16SBR System Bridge 4,
AN-Series
4, 25
parallel connections
series connections 19
12
4, 21
4, 21, 24
7, 23
23, 25
19, 29
19
20
19
23, 25, 26
8
ASI A-Net System Interface
Audio Networks 21
Audio Output Level 10
Audio Outputs
AV-M8
AV-M8 Mic Input Module 4
AV-P2 5, 25
22, 24
12
B
balanced signal
connecting 14
bidirectional
Block Diagram 32
28
C
cable length 6, 7
Cables
Extending
cable specification, Cat-5e 6
Cat-5 7
stranded vs. solid
Cat-5e cable length
Cat-5e UTP 25
Cat-6 6
Certifications iii
Channel Selector
Cleaning and Maintenance
Compatibility 4
computer network 5
Connecting an Unbalanced
Connecting Audio
crossover cables 6
Source
8
6
21, 25
2, 10, 11
14, 15
14
D
D-16c 21, 22, 24
D-16c card
4
daisy-chain
DC Power Connector 12
DiGiCo 4, 24
Digital Split 21
4
Dimensions 31
DIP switches 17
output level 10
Distributor 19, 29
dual mono 10
19
E
EtherCon Connector 6
Ethernet 5
Euroblock 12, 15
wiring 14
wiring an unbalanced
source 15
expanded network 28
Expanding 29
Expansion 23, 25
Extending A-Net 20
Extending Cable Lengths 8
F
fiber optic 20
Front Panel Components 2
Front Panel description 10
I
inline coupler 8
8
L
line-level
connecting 14
Local Area Network 5
long distance A-Net 20
M
maximum cable length 8, 25
media converter 20
Monitor Mixing System
mono 10
mounting flanges 9
Mute Switch 2, 10
N
Network 5
networking 5
Neutrik EtherCon. See EtherCon
O
Output Level 10, 17
Output Level DIP Switches 2
output level DIP switches 10
P
Package Contents 1
Panel Descriptions 10
Parallel A-Net Routing 19
parallel connection 19
Personal Mixer 4, 21, 25, 28
Power Connector 12
Power LED 2, 11
Power Supply 12
Pro16 Monitor Mixing Sys-
tem 28
Pro16 Series products 23, 28
Pro64 4
R
rack mounting 9
Rear Panel Components 3
Rear Panel description 12
RJ45 6
RoHS iii
router 5
S
series connection 19
Setting Output Level 17
28
signal repeater 20
Specifications 30
Split 21
stereo 10
Stereo Link 11
Stereo Pair LED 2, 11
stranded vs. solid Cat-5 6
System Bridge 4, 7, 23
U
Unbalanced Source
wiring Euroblocks 15
Unshielded Twisted Pair 6
UPS 8
UTP 6
UTP cable 25
W
Wiring a Euroblock 14
Y
Y1 21, 22
Y1 card 4
Y1 console interface card 24
Yamaha 4
36
Loading...