Avigilon 1.3C-H4SL-D-IR, 2.0C-H4SL-DO-IR, 2.0C-H4SL-D, 2.0C-H4SL-D-IR, 3.0C-H4SL-DIR Installation Manual
...
InstallationGuide
Avigilon H4 SL DomeCamera Models with Surface Mount
Adapter:
1.3C-H4SL-D, 1.3C-H4SL-D-IR,1.3C-H4SL-DO-IR, 2.0C-H4SL-D,
2.0C-H4SL-D-IR, 2.0C-H4SL-DO-IR, 3.0C-H4SL-D, 3.0C-H4SL-DIR, 3.0C-H4SL-DO-IR
Important Safety Information
This manual provides installation and operation information and precautions for the use of this camera. Incorrect
installation could cause an unexpected fault. Before installing this equipment read this manual carefully. Please
provide this manual to the owner of the equipment for future use.
The Warning symbol indicates the presence of dangerous voltage within and outside the product
enclosure that may constitute a risk of electric shock, serious injury or death to persons if proper
precautions are not followed.
The Caution symbol alerts the user to the presence of hazards that may cause minor or moderate injury
to persons, damage to property or damage to the product itself if proper precautions are not followed.
WARNING — Failure to observe the following instructions may result in severe injury or death.
l Installation must be performed by qualified personnel only, and must conform to all local codes.
l The H4SL-D product is intended to be supplied by Power over Ethernet (PoE) that is a “Limited Power
Source” or “LPS” rated 48 VDC, 4W min.
l The H4SL-DO product is intended to be supplied by Power over Ethernet (PoE) that is a “Limited Power
Source” or “LPS” rated 48 VDC, 7W min.
l Any external power supply connected to this product may only be connected to another Avigilon
product of the same model series. External power connections must be properly insulated.
l Do not connect directly to mains power for any reason.
CAUTION — Failure to observe the following instructions may result in injury or damage to the camera.
l Do not expose the camera directly to high levels of x-ray, laser, or UV radiation. Direct exposure may
cause permanent damage to the image sensor.
l Do not install near any heat sources such as radiators, heat registers, stoves, or other sources of heat.
l Do not subject the cables to excessive stress, heavy loads or pinching.
l Do not open or disassemble the device. There are no user serviceable parts.
l Refer all servicing to qualified personnel. Servicing may be required when the device has been damaged
(such as from a liquid spill or fallen objects), has been exposed to rain or moisture, does not operate
normally, or has been dropped.
l Do not use strong or abrasive detergents when cleaning the device body.
l Use only accessories recommended by Avigilon.
ii
Regulatory Notices
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
l Reorient or relocate the receiving antenna.
l Increase the separation between the equipment and the receiver.
l Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
l Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications made to this equipment not expressly approved by Avigilon Corporation or parties
authorized by Avigilon Corporation could void the user’s authority to operate this equipment.
Disposal and Recycling Information
When this product has reached the end of its useful life, please dispose of it according to your local
environmental laws and guidelines.
Risk of fire, explosion, and burns. Do not disassemble, crush, heat above 100 °C (212 °F), or incinerate.
European Union:
This symbol means that according to local laws and regulations your product should be disposed of separately
from household waste. When this product reaches its end of life, take it to a collection point designated by local
authorities. Some collection points accept products for free. The separate collection and recycling of your
product at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner
that protects human health and the environment.
iii
Legal Notices
©2016 -2017,Avigilon Corporation. All rights reserved. AVIGILON, the AVIGILON logo, AVIGILONCONTROL
CENTER, ACC, and TRUSTED SECURITY SOLUTIONS are trademarks of Avigilon Corporation. Other names
mentioned herein may be the trademarks of their respective owners. The absence of the symbols ™ and ® in
proximity to each trademark in this document is not a disclaimer of ownership of the related trademark. Avigilon
Corporation protects its innovations with patents issued in the United States of America and other jurisdictions
worldwide: avigilon.com/patents. Unless stated explicitly and in writing, no license is granted with respect to
any copyright, industrial design, trademark, patent or other intellectual property rights of Avigilon Corporation or
its licensors.
Disclaimer
This document has been compiled and published covering the latest product descriptions and specifications.
The contents of this document and the specifications of the products discussed herein are subject to change
without notice. Avigilon Corporation reserves the right to make any such changes without notice. Neither
Avigilon Corporation nor any of its affiliated companies: (1) guarantees the completeness or accuracy of the
information contained in this document; or (2) is responsible for your use of, or reliance on, the information.
Avigilon Corporation shall not be responsible for any losses or damages (including consequential damages)
caused by reliance on the information presented herein.
Avigilon Corporation
avigilon.com
PDF-H4SLDO-A
Revision: 2 - EN
20170307
iv
Table of Contents
Overview 1
Cover View 1
Mounting Adapter View 2
Camera Base Bottom View 3
Camera Base Front View 4
Camera Base Rear View 5
Installation 6
Required Tools and Materials 6
Camera Package Contents 6
Installation Steps 6
Removing the Dome Cover 7
Inserting Cables through the Sealing Grommet 7
Using the Surface Mount Adapter 8
Mounting the Dome Camera Using theBottom Cable Entry 8
Mounting the Dome Camera Using the Side Cable Entry 9
Mounting the Dome Camera to an Electrical Box 12
Installing the Camera Base to the Mounting Adapter 12
(Optional) Using the USB Wi-Fi Adapter 13
Assigning an IP Address 14
Accessing the Live VideoStream 14
Aiming the Dome Camera 14
(Optional) Configuring microSD Card Storage 16
Installing the Dome Cover 17
Zooming and Focusing the DomeCamera 17
Configuring the Camera 17
For More Information 18
LED Indicators 19
Removing the Dome Camera from the Mounting Adapter 20
Resetting to Factory Default Settings 21
Setting the IP Address Using the ARP/Ping Method 22
Specifications 23
Limited Warranty and Technical Support 25
v
Overview
Cover View
1.
Dome cover
Vandal resistant dome cover.
Only available on H4SL-DO models.
2.
Surface mount adapter
Used to mount the dome camera to a wall, ceiling or electrical box.
3.
Tamper resistant screws
Torx captive screws to fix the dome cover to the base.
4. Side cable entry cover
Covers the side cable entry hole.
Overview 1
Mounting Adapter View
1.
Lanyard
Connects to the lanyard anchor on the dome camera base.
2.
Camera housing clips
Snaps to hold camera module during installation.
3.
Cable entry hole
An entry hole for the cables required for camera operation.
4.
Mounting holes
Holes for mounting the adapter to the following:
A — UK standard single gang box
B — Octagon gang box
D — US standard single gang box
Mounting Adapter View 2
Camera Base Bottom View
1.
Cable entry hole
An entry hole for the cables required for camera operation.
2.
Lanyard anchor
The safety lanyard attaches to the anchor to prevent the camera from falling during installation.
3.
Vent
Vent to allow moisture vapor to escape the sealed housing and equalize pressure.
Only available on H4SL-DO models.
Camera Base Bottom View 3
Camera Base Front View
1.
IR illuminator
Provides scene illumination in the IR spectrum.
Only available on -IR models.
2.
Ethernet port
Accepts power and Ethernet connection to the network.
The camera can only be powered by Power over Ethernet (PoE). Server communication and image data
transmission also occur over this connection.
3.
Connection status LED
Provides information about camera operation. For more information, see LED Indicators on page19.
4.
Link LED
Indicates if there is an active connection in the Ethernet port.
5.
microSD card slot
Accepts a microSD card for onboard storage.
Camera Base Front View 4
Loading...