Avigilon H4A-DP1, H4A-DP1-IR, H4A-DP2, H4A-G-DP1-IR Installation Manual
Installation Guide
Avigilon™ H4 HD Dome Camera Models:
H4A-DP1, H4A-DP1-IR, H4A-DP2
Important Safety Information
This manual provides installation and operation information and precautions for the use of this camera. Incorrect
installation could cause an unexpected fault. Before installing this equipment read this manual carefully. Please
provide this manual to the owner of the equipment for future use.
The Warning symbol indicates the presence of dangerous voltage within and outside the product
enclosure that may constitute a risk of electric shock, serious injury or death to persons if proper
precautions are not followed.
The Caution symbol alerts the user to the presence of hazards that may cause minor or moderate injury
to persons, damage to property or damage to the product itself if proper precautions are not followed.
WARNING — Failure to observe the following instructions may result in severe injury or death.
l Installation must be performed by qualified personnel only, and must conform to all local codes.
l This product is intended to be supplied by a UL Listed Power Unit marked “Class 2” or “LPS” or “Limited
Power Source” with output rated 12 VDC or 24 VAC, 7 W min. (9 W min. for -IR model) or Power over
Ethernet (PoE), rated 48 VDC, 7 W min (9 W min. for -IR model).
l Any external power supply connected to this product may only be connected to another Avigilon product
of the same model series. External power connections must be properly insulated.
l Do not connect directly to mains power for any reason.
CAUTION — Failure to observe the following instructions may result in injury or damage to the camera.
l Do not expose the camera directly to high levels of x-ray, laser, or UV radiation. Direct exposure may
cause permanent damage to the image sensor.
l Do not install near any heat sources such as radiators, heat registers, stoves, or other sources of heat.
l Do not subject the cables to excessive stress, heavy loads or pinching.
l Do not open or disassemble the device. There are no user serviceable parts.
l Refer all servicing to qualified personnel. Servicing may be required when the device has been damaged
(such as from a liquid spill or fallen objects), has been exposed to rain or moisture, does not operate
normally, or has been dropped.
l Do not use strong or abrasive detergents when cleaning the device body.
l Use only accessories recommended by Avigilon.
ii
Regulatory Notices
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
l Reorient or relocate the receiving antenna.
l Increase the separation between the equipment and the receiver.
l Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
l Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications made to this equipment not expressly approved by Avigilon Corporation or parties
authorized by Avigilon Corporation could void the user’s authority to operate this equipment.
Disposal and Recycling Information
When this product has reached the end of its useful life, please dispose of it according to your local
environmental laws and guidelines.
Risk of fire, explosion, and burns. Do not disassemble, crush, heat above 100 °C (212 °F), or incinerate.
European Union:
This symbol means that according to local laws and regulations your product should be disposed of separately
from household waste. When this product reaches its end of life, take it to a collection point designated by local
authorities. Some collection points accept products for free. The separate collection and recycling of your
product at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner
that protects human health and the environment.
iii
Legal Notices
©2016,Avigilon Corporation. All rights reserved. All rights reserved. AVIGILON, the AVIGILON logo, and
AVIGILONCONTROL CENTER are trademarks of Avigilon Corporation. Other product names mentioned herein
may be the trademarks of their respective owners. The absence of the symbols ™ and ® in proximity to each
trademark in this document is not a disclaimer of ownership of the related trademark. Avigilon Corporation
protects its innovations with patents issued in the United States of America and other jurisdictions worldwide:
http://www.avigilon.com/patents Unless stated explicitly and in writing, no license is granted with respect to any
copyright, industrial design, trademark, patent or other intellectual property rights of Avigilon Corporation or its
licensors.
Disclaimer
This document has been compiled and published covering the latest product descriptions and specifications.
The contents of this document and the specifications of the products discussed herein are subject to change
without notice. Avigilon Corporation reserves the right to make any such changes without notice. Neither
Avigilon Corporation nor any of its affiliated companies guarantees the completeness or accuracy of the
information contained in this document and is not responsible for your use of, or reliance on, the information.
Avigilon Corporation shall not be responsible for any losses or damages (including consequential damages)
caused by reliance on the information presented herein.
Avigilon Corporation
http://www.avigilon.com
PDF-H4ADP-A
Revision: 1 - EN
20160112
iv
Table of Contents
Overview 1
Cover View 1
Bottom View 2
Top View 3
Front View 4
Rear View 5
IR View 6
Pendant Wall Mount Bracket View 7
Pendant Wall Mount View 8
Pendant NPT Mount View 9
Installation 10
Required Tools and Materials 10
Package Contents 10
Installation Steps 10
Removing the Dome Cover 11
Mounting and Aiming Video Analytics Cameras 11
Inserting Cables through the Sealing Grommet 11
Mounting the Dome Camera 12
Mounting the Dome Camera to the Pendant Wall Mount 12
Mounting the Dome Camera to the Pendant NPT Mount 15
Connecting Cables 17
Assigning an IP Address 17
(Optional) Using the USB Wifi Adapter 18
Accessing the Live VideoStream 18
Aiming the Dome Camera 18
(Optional) Configuring Onboard SD Card Storage 19
Installing the Dome Cover 19
Zooming and Focusing the DomeCamera 19
Configuring the Camera 20
For More Information 20
Cable Connections 21
Connecting External Power 21
Connecting to External Devices 21
Connecting to Microphones, Speakers and Video Monitors 22
LED Indicators 24
v
Resetting to Factory Default Settings 25
Setting the IP Address Using the ARP/Ping Method 26
Cleaning 27
Dome Bubble 27
Body 27
Specifications 28
Limited Warranty & Technical Support 30
vi
Overview
Cover View
1. Tamper Resistant Screws
Torx captive screws to fix the dome cover to the base.
2. Dome Cover
Vandal proof dome cover.
Overview 1
Bottom View
1. Camera Alignment Latch
A latch for locking the camera into the pendant wall mount or the pendant NPT mount.
2. Camera Lanyard Hook
A hook for suspending the camera from the lanyard provided in the pendant wall mount or the pendant
NPT mount.
3. Cable Entry Hole
An entry hole for the cables required for camera operation.
2 Bottom View
Top View
1. Camera Mounting Scre ws
Screws for securing the camera to the pendant wall mount or the pendant NPT mount.
2. Lanyard
Connects to a lanyard hook on the dome cover.
Top View 3
Front View
1. Power Connector Block
Accepts a terminal block with either an AC or DC power connection. DC input can be either polarity. Only
required when Power over Ethernet is not available.
2. Link LED
Indicates if there is an active connection in the Ethernet port.
3. Ethernet Port
Accepts an Ethernet connection to a network. Server communication and image data transmission occurs
over this connection. Also receives power when it is connected to a network that provides Power over
Ethernet.
4. Connection Status LED
Provides information about camera operation. For more information, see LED Indicators on page 24
5. Serial Number Tag
Device information, product serial number and part number label.
6. Audio/Video Connector
Accepts a mini-jack connector (3.5 mm).
4 Front View
Rear View
1. Azimuth Control
Provides control of the image angle.
2. SD Card Slot
Accepts an SD card for onboard storage.
3. Micro USB Port
Accepts a micro USB to USB adapter. Only required when using the Avigilon USB Wifi Adapter.
4. I/O Connector Block
Provides connections to external input/output devices.
5. Tilt Lock Thumb Screw
Provides a locking mechanism for the image tilt adjustment.
6. Pan Lock Thumb Screw
Provides a locking mechanism for the image pan adjustment
Rear View 5
Loading...