How it Works
Avigilon
Loading...
2.0-H3-DC1
Installation Manual
150 pgs5.53 Mb0

Avigilon 2.0-H3-DC1, 1.0-H3-DC1, 5.0-H3-DC1, 3.0W-H3-DC1, 1.0-H3-D1 Installation Manual

...
Installation Guide
Avigilon High Definition H.264 IP Dome Camera Models:
1.0-H3-DC1, 2.0-H3-DC1, 3.0W-H3-DC1 and 5.0-H3-DC1
920-0051A-Rev1
i
Important Safety Information
This manual provides installation and operation information and precautions for the use of this dome camera. Incorrect installation could cause an unexpected fault. Before installing this equipment read this manual carefully. Please provide this manual to the owner of the equipment for future use.
• Do not use near water or expose to dripping or splashing. Do not place objects filled with liquids above the device.
• Do not expose to rain or moisture.
• For indoor use only. If used outdoors, an approved outdoor mounting adapter or enclosure is required. Consult with Avigilon for more information.
• Installation must be performed by qualified personnel only, and must conform to all local codes.
• This product is intended to be supplied by a UL Listed Power Unit marked “Class 2” or “LPS” or “Limited Power Source” with output rated 12 VDC or 24 VAC, 5 W min. or Power over Ethernet (PoE), rated 48 VDC, 5 W min.
The Warning symbol indicates the presence of dangerous voltage within and outside the product enclosure that may constitute a risk of electric shock, serious injury or death to persons if proper precautions are not followed.
The Caution symbol alerts the user to the presence of hazards that may cause minor or moderate injury to persons, damage to property or damage to the product itself if proper precautions are not followed.
Warning — Failure to observe the following instructions
may result in severe injury or death.
ii
• Any external power supply connected to this product may only be connected to another Avigilon product of the same model series. External power connections must be properly insulated.
• Do not connect directly to mains power for any reason.
• Do not install near any heat sources such as radiators, heat registers, stoves, or other sources of heat.
• Do not subject the cables to excessive stress, heavy loads or pinching.
• Do not open or disassemble the device. There are no user serviceable parts.
• Refer all servicing to qualified personnel. Servicing may be required when the device has been damaged (such as from a liquid spill or fallen objects), has been exposed to rain or moisture, does not operate normally, or has been dropped.
• Do not use strong or abrasive detergents when cleaning the device body.
• Use only accessories recommended by Avigilon.
• Use of controls or adjustments or performance of procedures other than those specified in this document may result in hazardous radiation exposure.
Caution — Failure to observe the following instructions
may result in injury or damage to the dome camera.
iii
Regulatory Notices
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This Class B digital apparatus complies with Canadian ICES-003.
FCC Notice
This equipment has been tested and found to comply with the limits for a Class B computing device pursuant to Subpart B of Part 15 of FCC rules, which are designed to provide reasonable protection against such interference when operated in a commercial environment. Operation of this equipment in a residential area is likely to cause interference, in which case the user at his/her own expense will be required to take whatever measures may be required to correct the interference.
Changes or modifications made to this equipment not expressly approved by Avigilon Corporation or parties authorized by Avigilon Corporation could void the user’s authority to operate this equipment.
Disposal and Recycling Information
When this product has reached the end of its useful life, please dispose of it according to your local environmental laws and guidelines.
European Union:
This symbol means that according to local laws and regulations your product should be disposed of separately from household waste. When this product reaches its end of life, take it to a collection point designated by local authorities. Some collection points accept products for free. The separate collection and recycling of your product at the time of disposal will help conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment.
iv
Other Notices
Compilation and Publication Notice
This manual has been compiled and published covering the latest product descriptions and specifications. The contents of this manual and the specifications of this product are subject to change without notice. Avigilon reserves the right to make changes without notice in the specifications and materials contained herein and shall not be responsible for any damages (including consequential) caused by reliance on the materials presented, including but not limited to typographical and other errors relating to the publication.
Intellectual Property Notice
No license is granted by implication or otherwise under any industrial design, industrial design rights, patent, patent rights, or copyrights of Avigilon Corporation or its licensors. Trademarks and registered trademarks are the property of their respective owners.
Table of Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Cover View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Bottom View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Front View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Required Tools and Materials . . . . . . . . . . . . . . . . . 4
Camera Package Contents . . . . . . . . . . . . . . . . . . . 4
Installation Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Removing the Dome Cover . . . . . . . . . . . . . . 4
Mounting the Dome Camera . . . . . . . . . . . . .5
Connecting Cables . . . . . . . . . . . . . . . . . . . . 6
Assigning an IP Address . . . . . . . . . . . . . . . .6
Accessing the Live Video Stream . . . . . . . . .7
Aiming the Dome Camera . . . . . . . . . . . . . . . 7
Removing the Dome Cover . . . . . . . . . . . . . . 8
Focusing the Dome Camera . . . . . . . . . . . . .8
For More Information . . . . . . . . . . . . . . . . . .8
Cable Connections . . . . . . . . . . . . . . . . . . . . . . 9
Connecting Power . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Connecting to External Devices . . . . . . . . . . . . . . . 10
Connecting to Microphones, Speakers
and Video Monitors . . . . . . . . . . . . . . . . . . . . . . . . 11
LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . 12
Reset to Factory Default Settings . . . . . . . . . 13
Setting the IP Address Through the ARP/Ping
Method . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . 15
Limited Warranty & Technical Support . . . . 16
1
Overview
Cover View
Feature Description
Dome Cover Vandal proof dome cover constructed
out of plastic with a polycarbonate bubble.
Tamper Proof Screws TORX tamper-resistant captive screws
to fix the dome cover to the base.
Dome Cover
Tamper Proof Screws
2
Bottom View
Feature Description
Cable Entry Hole An entry hole for network, power and I/O
cables.
Ceiling Panel Clamps Clamps for securing the dome camera
to the ceiling panel.
Serial Number Tag Product serial number and part number
label.
Serial Number Label
Ceiling Panel Clamps
Cable Entry Hole
3
Front View
Feature Description
Tilt Lock Thumb Screws
Provides a locking mechanism for the image tilt adjustment.
Pan Lock Thumb Screws
Provides a locking mechanism for the image pan
adjustment. Azimuth Control Provides adjustment of the image angle. Ethernet Port Accepts an Ethernet connection to a network. Server
communication and image data transmission occurs over
this connection. Also receives power when it is
connected to a network that provides Power over
Ethernet. Power Connector
Block
Accepts a terminal block with either AC or DC power
connection. DC input can be either polarity. Only required
when Power over Ethernet is not available. Audio/Video
Connector
Accepts a mini-jack connector (3.5 mm). See the section
about connecting microphones and monitors for more
information. I/O Terminals Provides connections to external input/output devices.
See the section about connecting external devices for
more information. Connection Status
LED
Provides information about device operation. See the
section about LED indicators for more information. Link LED Indicates if there is an active connection in the Ethernet
port.
Azimuth Control
Link LED
Connection Status LED
Ethernet Port Power Connector Block
Audio/Video Connector
ilt Lock Thumb Screw
Pan Lock Thumb Screw
I/O Terminals
4
Installation
Required Tools and Materials
• Small slotted screwdriver with 5/64” or 2 mm blade width — for connecting power when not using Power over Ethernet.
Camera Package Contents
Ensure the package contains the following:
• Avigilon High Definition IP Dome Camera
• Terminal block
• T20 TORX tamper resistant key
• Hole template sticker
Installation Steps
Complete the following procedures to install the dome camera.
1. Removing the Dome Cover on page 4
2. Mounting the Dome Camera on page 5
3. Connecting Cables on page 6
4. Assigning an IP Address on page 6
5. Accessing the Live Video Stream on page 7
6. Aiming the Dome Camera on page 7
7. Removing the Dome Cover on page 8
8. Focusing the Dome Camera on page 8
Removing the Dome Cover
Remove the dome cover by loosening the 2 tamper-proof screws that fix the cover to the base. The tamper resistant key included with the dome camera can be used to loosen the screws.
NOTE: Be careful not to scratch the dome bubble.
5
Mounting the Dome Camera
Perform the following steps to mount the dome camera to the ceiling:
1. Use the hole template to cut a 144 mm (5.5”) hole in a ceiling panel.
2. Insert the dome camera into the hole, and pull the cables through the dome camera’s cable entry hole.
3. Tighten the two clamping screws until the dome camera is secured to the ceiling.
NOTE: Over-tightening the clamping screws may cause damage to
the ceiling or in-ceiling mount
.
Caution — The ceiling material must be able to sustain a minimum of 0.6 kg (1.2 lbs).
Caution — This camera is designed for indoor use only.
6
Connecting Cables
Refer to the diagrams in the Overview section for the location of the different connectors.
To connect the cables required for proper operation, complete the following:
1. If there are external input or output devices that need to be connected to the camera (for example: door contacts, relays, etc), connect the devices to the camera I/O Terminals. For more information, see Connecting to External Devices.
2. If an external microphone or external video monitor needs to be connected to the camera, connect the devices to the camera Audio/Video Connector. For more information, see Connecting to Microphones and Video Monitors.
3. Connect the Ethernet Port (RJ45 connector) to a network using an Ethernet network cable. The Link LED will turn on once a network link has been established.
4. Connect power using one of the following methods:
• Power over Ethernet (PoE) Class 3 — If PoE is
available, the camera is automatically detected when the network cable is connected.
• External Power — Connect an external 12 VDC or
24 VAC power source to the power connector block. For more information, see Connecting Power.
5. Check that the Connection Status LED indicates the correct state. For more information, see LED Indicators.
Assigning an IP Address
The camera automatically obtains an IP address by default. Once connected to a network, it attempts to locate and obtain an IP address from a DHCP server. If this fails, Zero Configuration Networking
7
(Zeroconf) is used to choose an IP address. When the IP address is set using Zeroconf, the IP address is in the 169.254.0.0/16 subnet.
The IP address settings can be changed using one of the following methods:
• (Recommended) Avigilon Camera Installation Tool software application.
• Camera's web browser interface: http://<camera IP address>/
• ARP/Ping method. For more information, see Setting the IP Address through the ARP/Ping Method.
• Network Video Management software application (for example, Avigilon Control Center).
NOTE: The default camera username is admin and the default
password is admin.
Accessing the Live Video Stream
Live video stream can be viewed using one of the following methods:
• (Recommended) Avigilon Camera Installation Tool software application.
• Camera's web browser interface: http://<camera IP address>/.
• Network Video Management software application (for example, Avigilon Control Center).
NOTE: The default camera username is admin and the default
password is admin.
Aiming the Dome Camera
1. Loosen the pan and tilt lock screws on the camera.
2. Turn the lens to the desired direction by panning and tilting the lens.
3. Once satisfied, tighten the pan and tilt lock screws to secure the dome camera’s position.
4. Rotate the azimuth control ring to set the image to the correct angle.
8
5. In the Avigilon Camera Installation Tool, adjust the camera’s Image and Display settings to achieve the desired zoom position.
Removing the Dome Cover
Remove the dome cover by loosening the 2 tamper-proof screws that fix the cover to the base. The tamper resistant key included with the dome camera can be used to loosen the screws.
NOTE: Be careful not to scratch the dome bubble.
Focusing the Dome Camera
NOTE: Ensure this procedure is performed after the dome cover is
installed, so the focus shift caused by the dome bubble’s refraction can be accomodated.
• In the Avigilon Camera Installation Tool, use the camera’s Image and Display settings to focus the camera lens. a. Click the Auto Focus button to focus the lens.
b. If the desired focus was not achieved, use the focus
near and far buttons to adjust the focus.
For More Information
Additional information about setting up and using the device is available in the following guides:
• Avigilon Camera Installation Tool User Guide
• Avigilon Control Center Client User Guide
• Avigilon High Definition H.264 IP Camera User Guide
The manuals are available on the Avigilon website:
http://avigilon.com/
support/manuals/.
Caution — Do not attempt to adjust the focus and zoom on the camera manually or the camera lens may become damaged.
9
Cable Connections
Connecting Power
NOTE: Do not perform this procedure if Power over Ethernet (POE) is
used.
If PoE is not available, the dome camera needs to be powered through the removable power connector block. Refer to the diagrams in this guide for the location of the power connector block.
The device can be powered from 12 VDC or 24 VAC. The power consumption information is listed in the product specifications.
To connect power to the power connector block, complete the following steps:
1. Remove the power connector block from the device.
2. Remove the insulation from ¼” (6 mm) of the power wires. Do not nick or damage the wires.
3. Insert the two power wires into the two terminals on the power connector block. The connection can be made with either polarity.
Use a small slotted (5/64” or 2 mm blade width) screwdriver to loosen and tighten the terminals.
4. Attach the power connector block back into the receptacle on the device.
Warning — This product is intended to be supplied by a UL Listed Power Unit marked “Class 2” or “LPS” or “Limited Power Source” with output rated 12 VDC or 24 VAC, 5 W min. or PoE rated 48 VDC, 5 W min.
10
Connecting to External Devices
External devices are connected to the camera through the I/O terminal. The pinout for the I/O terminal is shown in the following table and diagram.
Figure: External I/O terminal schematics and example application.
Table:External I/O Terminals
Pin Function Description
1 Ground Ground 2 Input To activate, connect the Input to the Ground
pin. To deactivate, leave disconnected or apply between 3-15 V.
3 Output When active, Output is internally connected
with the Ground pin. Circuit is open when inactive. Maximum load is 25 VDC, 120 mA.
Switch
Relay
11
Connecting to Microphones, Speakers and Video Monitors
The camera can be connected to an external microphone, speaker and video monitor through the audio/video connector. The connector is a mini-jack (3.5 mm), and the pinout for it is shown in the following diagram.
NOTE: The camera only supports line level mono audio input and an
NTSC or PAL video output.
The video output signal is determined by the camera flicker control setting. When the camera flicker control is set to 60 Hz, the video output signal is NTSC. When the flicker control is set to 50 Hz, the video output signal is PAL. Use the Avigilon Camera Installation Tool to configure the camera’s flicker control in the Image and Display setup.
NOTE: Video output is disabled when the camera is encoding multiple
H264 or JPEG streams. Use the Avigilon Camera Installation Tool to configure the camera’s Compression and Image Rate setup.
Figure: Mini-jack audio video connector.
Audio IN
Composite Video OUT
GND
Audio OUT
12
LED Indicators
Once the camera is connected to the network, the connection status LEDs will display the camera’s progress in connecting to the Network Video Management software.
The following table describes what the LEDs indicate:
Table:LED Indicators
Connection
State
Connection
Status LED
Description
No Link Off Not physically connected to any
network device.
Obtaining IP Address
One short flash every second
Attempting to obtain an IP address.
Connecting to NVR
Two short flashes every second
An IP address has been obtained and is attempting to connect to the server
Upgrading Firmware
Two short flashes and one long flash every second
Updating the firmware.
Connected On Connected to the Network Video
Management software.
13
Reset to Factory Default Settings
If the camera no longer functions as expected, you can choose to restore the camera to its factory default settings.
Use the firmware revert button to reset the camera.
Figure: The firmware revert microswitch on the side of the dome camera.
1. Disconnect power from the camera.
2. Using a straightened paperclip or similar tool, gently press and hold the firmware revert microswitch.
3. While continuing to hold the microswitch, power the device. Release the microswitch after three seconds.
Caution — Do not apply excessive force. Inserting the tool too far will damage the device.
Firmware Revert Button
14
Setting the IP Address Through the ARP/Ping Method
Complete the following steps to configure the camera to use a specific IP address:
1. Locate and copy down the MAC Address (MAC) listed on the Serial Number Tag for reference.
2. Open Command Prompt. From the Windows Start menu, select Run... then enter
cmd in the Run dialog box and click OK.
3. In Command Prompt, enter the following commands: a. arp -s <New Camera IP Address> <Camera
MAC Address>
For example: arp -s 192.168.1.10 00-18-
85-12-45-78
b. ping -l 123 -t <New Camera IP Address>
For example: ping -l 123 -t 192.168.1.10
4. Reboot the camera.
5. Close Command Prompt when you see the following message:
Reply IP from <New Camera IP Address>: ...
15
Specifications
Camera
Audio Input Line input, A/V mini-jack (3.5 mm) Video Output NTSC/PAL, A/V mini-jack (3.5 mm) Lens 3-9mm, F1.2, P-iris
Network
Network 100Base-TX Cabling Type CAT5 Connector RJ-45 API
ONVIF compliant (www.onvif.org)
Security Password protection, HTTPS encryption, digest authentication, WS
authentication, user access log
Protocols IPv4, HTTP, HTTPS, SOAP, DNS, NTP, RTSP, RTCP, RTP, TCP, UDP,
IGMP, ICMP, DHCP, Zeroconf, ARP
Streaming Protocols RTP/UDP, RTP/UDP multicast, RTP/RTSP/TCP, RTP/RTSP/HTTP/
TCP, RTP/RTSP/HTTPS/TCP, HTTP
Mechanical
Dimensions ØxH 167 mm x 130 mm, 6.6” x 5.1” Weight 0.56 kg (1.2 lb) Dome Bubble Polycarbonate, clear Body Plastic Housing Recessed mount, tamper resistant Finish Plastic, RAL 9003 Adjustment Range 360° pan, 180° tilt, 180° azimuth
Electrical
Power Source VDC: 12 V
VAC: 24 V
PoE: IEEE802.3af Class 3 compliant Power Consumption 5 W Power Connector 2-pin terminal block
Environmental
Operating Temperature -10 °C to +50 °C (14 °F to 122 °F) Storage Temperature -10 °C to +70 °C (14 °F to 158 °F) Humidity 20 - 80% Relative humidity (non-condensing)
Certifications
UL 60950 CSA60950
EN 60950-1 CE
ROHS WEEE Electromagnetic Emissions FCC Part 15 Subpart B Class B IC ICES-003 Class B
EN 55022 Class B Electromagnetic Immunity EN 55024 EN 61000-4-2
EN 61000-4-3 EN 61000-4-4
EN 61000-4-5 EN 61000-4-6
EN 61000-4-11
16
Limited Warranty & Technical Support
Avigilon warrants to the original consumer purchaser, that this product will be free of defects in material and workmanship for a period of 3 years from date of purchase. The manufacturer’s liability hereunder is limited to replacement of the product, repair of the product or replacement of the product with repaired product at the discretion of the manufacturer. This warranty is void if the product has been damaged by accident, unreasonable use, neglect, tampering or other causes not arising from defects in material or workmanship. This warranty extends to the original consumer purchaser of the product only.
AVIGILON DISCLAIMS ALL OTHER WARRANTIES EXPRESSED OR IMPLIED INCLUDING, WITHOUT LIMITATION, ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, EXCEPT TO THE EXTENT THAT ANY WARRANTIES IMPLIED BY LAW CANNOT BE VALIDLY WAIVED.
No oral or written information, advice or representation provided by Avigilon, its distributors, dealers, agents or employees shall create another warranty or modify this warranty. This warranty states Avigilon’s entire liability and your exclusive remedy against Avigilon for any failure of this product to operate properly.
In no event shall Avigilon be liable for any indirect, incidental, special, consequential, exemplary, or punitive damages whatsoever (including but not limited to, damages for loss of profits or confidential or other information, for business interruption, for personal injury, for loss of privacy, for failure to meet any duty including of good faith or of reasonable care, for negligence, and for any other pecuniary or other loss whatsoever) arising from the use of or inability to use the product, even if advised of the possibility of such damages. Since some jurisdictions do not allow the above limitation of liability, such limitation may not apply to you.
This Limited Warranty gives you specific legal rights and you may also have other rights which vary from jurisdiction to jurisdiction.
Warranty service and technical support can be obtained by contacting Avigilon Technical Support by phone at
1.888.281.5182 or via email at support@Avigilon.com.
Guide d'installation
Modèles de caméra dôme IP H.264 haute définition Avigilon :
1.0-H3-DC1, 2.0-H3-DC1, 3.0W-H3-DC1 et 5.0-H3-DC1
i
Français
Informations de sécurité importantes
Ce manuel fournit des informations d'installation et d'exploitation, ainsi que des précautions d'utilisation pour la caméra dôme. Une installation incorrecte peut entraîner une défaillance imprévue. Avant d'installer cet équipement, lisez attentivement ce manuel. Veuillez remettre ce manuel au propriétaire de l'équipement pour une utilisation ultérieure.
• N'utilisez pas l'équipement à proximité de l'eau ; ne l'exposez pas à des éclaboussures ou des fuites. Ne placez aucun objet rempli de liquide au-dessus de l'équipement.
• N'exposez pas l'équipement à la pluie ou aux moisissures.
• Pour une utilisation en intérieur uniquement. Si l'équipement est utilisé en extérieur, un adaptateur ou un boîtier de fixation en extérieur approuvé est obligatoire. Consultez Avigilon pour plus d'informations.
• L'installation doit être effectuée par un personnel qualifié uniquement et doit être en conformité avec tous les codes locaux.
Le symbole d'avertissement indique la présence de tensions dangereuses, à l'intérieur et à l'extérieur du boîtier du produit, susceptibles de générer un risque de choc électrique, de blessure grave, voire de décès, si des précautions appropriées ne sont pas prises.
Le symbole Attention alerte l'utilisateur sur la présence de dangers susceptibles d'infliger aux personnels des blessures mineures à modérées, d'endommager des biens ou le produit lui-même si des précautions appropriées ne sont pas prises.
Avertissement — Le non-respect des instructions suivantes est susceptible d'entraîner des blessures graves voire le décès.
ii
Français
• Ce produit doit être alimenté par une alimentation répertoriée UL et portant le marquage "Classe 2", "LPS" ou "Limited Power Source", d'une capacité de sortie nominale de 12 VCC ou 24 VCA pour 5 W min. ou, en mode PoE (Power over Ethernet), de 48 VCC pour 5 W min.
• Toute alimentation externe connectée à ce produit ne peut être connectée qu'à un autre produit Avigilon de la même gamme de modèles. Les connexions à des alimentations externes doivent être correctement isolées.
• Pour quelque raison que ce soit, ne connectez pas l'équipement directement au secteur.
• N'effectuez aucune installation à proximité de sources de chaleur telles que radiateurs, bouches de chaleur ou poêles.
• Ne soumettez pas les câbles à des tensions, des charges ou des pincements excessifs.
• N'ouvrez pas l'équipement, ne le démontez pas. Il ne contient aucune pièce sur laquelle l'utilisateur peut intervenir.
• Pour toute intervention, contactez un personnel qualifié. Une intervention peut se révéler nécessaire lorsque l'équipement est endommagé (par exemple, par le renversement d'un liquide ou la chute d'un objet), lorsqu'il a été exposé à la pluie ou à l'humidité (présence de moisissure), lorsqu'il ne fonctionne pas normalement ou lorsqu'il a chuté.
• N'utilisez pas de détergents puissants ou abrasifs lorsque vous nettoyez le corps de l'équipement.
• Utilisez uniquement les accessoires recommandés par Avigilon.
• L'utilisation de commandes, de réglages ou de procédures autres que ceux spécifiés dans le présent document peut entraîner une exposition à des radiations dangereuses.
Attention — Le non-respect des instructions suivantes est susceptible d'entraîner des blessures et d'endommager la caméra dôme.
iii
Français
Avis concernant la réglementation
Cet équipement est conforme à section 15 des règles FCC. Son exploitation est sujettes aux deux conditions suivantes : (1) Cet équipement ne risque pas de générer d'interférences nuisibles et (2) cet équipement doit accepter toute interférence reçue, y compris celles susceptibles d'induire un fonctionnement indésirable.
Cet équipement numérique de Classe B est conforme à la norme canadienne ICES-003.
Notice FCC
Cet équipement a été testé et déclaré conforme aux limitations relatives à un appareil numérique de classe B, en vertu de la Sous­section B de la Section 15 des règles de la FCC. Ces limitations visent à assurer une protection raisonnable contre les interférences dans le cadre d'une exploitation de l'équipement dans un environnement commercial. L'exploitation de cet équipement dans une zone résidentielle est susceptible de générer des interférences nuisibles, auquel cas l'utilisateur sera tenu de prendre toute mesure nécessaire pour remédier à ces interférences.
Tout changement ou modification apporté à cet équipement non expressément approuvé par Avigilon Corporation ou des tiers autorisés par Avigilon Corporation pourrait annuler l'autorisation accordée à l'utilisateur d'utiliser cet équipement.
Informations sur la mise au rebut et le recyclage
Lorsque ce produit aura atteint la fin de sa vie utile, veuillez le mettre au rebut conformément aux directives et à la législation locales sur l'environnement.
Union européenne :
Ce symbole signifie que, conformément aux lois et aux réglementations locales, votre produit doit être mis au rebut hors déchets ménagers. Lorsque ce produit aura atteint la fin de sa vie utile, portez-le à un point de collecte désigné par les autorités locales. Certains points de collecte acceptent gratuitement les produits. La collecte et le recyclage séparés de votre produit au moment de la mise au rebut contribuent à conserver les ressources naturelles et garantissent que le produit est recyclé de sorte à protéger la santé humaine et l'environnement.
iv
Français
Autres notices
Notice sur la compilation et la publication
Ce manuel a été compilé et publié en couvrant les spécifications et descriptions de produit les plus récentes. Le contenu de ce manuel et les spécifications de ce produit sont sujets à modifications sans avis préalable. Avigilon se réserve le droit d'apporter des modifications sans avis préalable aux spécifications et informations présentées dans le présent manuel. Avigilon ne saurait être tenu responsable de tout dommage (notamment accessoire) causé par le fait de se fier aux informations présentées, notamment mais sans s'y limiter, en termes d'erreurs typographiques et d'autres erreurs liées à la publication.
Notice de propriété intellectuelle
Aucun licence n'est accordée par implication ou autre action dans le cadre de toute conception industrielle, de droits de conception industriels, de brevet et droits de brevet, ou de droits de reproduction (copyrights) d'Avigilon Corporation ou de ses concédants de licence. Les marques commerciales et les marques déposées sont la propriété de leurs détenteurs respectifs.
Loading...
+ 120 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use