Avid Configuration Guidelines
HP Z240 Workstation Tower / SFF
Single Quad Core CPU
Page 1 of 15
Joe Conforti – Avid Technology – January 15th 2016
HP Z240 Workstation – Tower / SFF Rev A Config Guide
1.) HP Z240 Tower and SFF [Small Form Factor] AVID Qualified System Specification:
Z240 / AVID Qualified Operating System:
Supported: Microsoft® Windows 7 Professional 64-bit Edition withSP1 (SP1 required)
Supported: Microsoft® Windows 8.1 - Professional (64bit) and Windows 8.1 Enterprise (64bit)
Not Supported
Not Supported - Microsoft® Windows 7 – any 32-bit version, or any version of Home, Ultimate or Enterprise
editions.
Not Supported - Microsoft® Windows XP or Vista 32 or 64-bit (any version)
Z240 / AVID Qualified Hardware Configuration
Qualified CPU
1.) Single Intel® Quad-Core Xeon® E3-1245 V5 Processor @ 3.4GHz (3.9GHz Turbo) / 8MB cache /
2133MHz DDR4 memory. The Xeon® E3-1245 V5 Processor includes Intel embedded graphics – HD
P530.
Video Card (GPU)
1. Embedded Intel HD Graphics P530 (The embedded Intel HD P530 graphics are supported for use
with Media Composer. Dedicated memory for the HD P530 graphics must be set to 1GB via the
system BIOS. If the memory for the Intel HD P530 is not set properly, the Media Composer s/w
will not initialize. Refer to the BIOS settings section of this document.
2. Optional - NVIDIA Quadro K620 or K1200 PCI-Express video board (not required)
O.S. System Hard Drive choices
HP M.2 SSD Drive (Best: Option A – extremely fast)
HP Z Turbo Drive G2 (Best: Option B – extremely fast , but , requires utilization of a
PCIe Gen3 x4 slot)
SATA 6Gbs SSD (better)
SATA 7200RPM Hard disk (good)
Supported Memory Configurations
1.) Memory: 8GB (2 x 4GB) DDR4 2133 ECC memory –
Requires two 4GB DIMMs installed in memory slots DIMM1 and DIMM3
2.) Memory: 16GB (4 x 4GB) DDR4 2133 ECC memory –
Requires four 4GB DIMMs installed in all 4 memory slots.
3.) Memory: 16GB (2 x 8GB) DDR4 2133 ECC memory –
Requires two 8GB DIMMs installed in memory slots DIMM1 and DIMM3
4.) Memory: 32GB (4 x 8GB) DDR4 2133 ECC memory –
Requires four 8GB DIMMs installed in all 4 memory slots.
Memory configuration constraints
Memory configurations which mix and match memory module sizes and locations should be avoided as they
may potentially result in a poor performing, non-optimal Avid editing operating environment.
Page 2 of 15
Joe Conforti – Avid Technology – January 15th 2016
HP Z240 Workstation – Tower / SFF Rev A Config Guide
Memory Installation (same for SFF and Tower):
Config
DIMM 1
DIMM 2
DIMM 3
DIMM 4
8GB (2 x 4GB)
X X
16GB (4 x 4GB)
X X X
X
16GB (2 x 8GB)
X X
32GB (4 x 8GB)
X X X
X
Qualified Operating System
Win 7 Pro 64-bit SP1
Windows 8.1 - Professional (64bit)
Windows 8.1 Enterprise (64bit)
Media Composer
M/C 8.2.5 (minimum)
ISIS 1Gb or (2 x1Gb) Ethernet
Client
v4.7x
ISIS 10Gb Hi-res Ethernet Client
Not Supported
StarTech 1394 PCIe Firewire
adapter. 2 FW800 and 1 FW400
ports. Half height PCIe card
(PEX1394B3)
The StarTech HBA is the only supported interface for 1394 camera or deck.
Can also be used for 1394 disk drives (recommended only for file transfers).
AVID qualified
HBA
SFF Slot
Tower
Slot
Function
Optional - NVIDIA
Quadro K620 or
K1200 PCI-Express
video board
#1 #2
Optional Nvidia Graphics GPU
HP Z Turbo Drive
G2, PCIe Solid
State Storage
#1 or 4
#2 , 3 or 4
HP PCIe solid state drive. Can be used as the boot drive or local storage:
http://www8.hp.com/us/en/campaigns/workstations/z-turbo-drive-g2.html
SAS Storage
Controller
#1 or 4
#2 , 3 or 4
Local SAS Storage: Suggest Atto Controllers. See section #6 below.
Slot #4 or #2 are preferred
Intel i350-T2
Dual-Port 1Gb
Ethernet Adapter
#4 # 4
Dual Gb connectivity for ISIS
StarTech 1394
PCIe Firewire
adapter. 2 FW800
and 1 FW400 ports.
Half height PCIe
card (PEX1394B3)
#2 #1
1394 connectivity for 1394 camera / deck
(HBA available direct from StarTech)
http://www.startech.com/Cards-Adapters/FireWire/3-Port-2b-1a-1394-PCIExpress-FireWire-Card-Adapter~PEX1394B3
HP Z240 Memory DIMM Installation order
DIMMs are labelled on the motherboard 1, 2, 3, 4. Load DIMMs in the following order:
2.) Qualified O.S., Software, Hardware and shared storage supported:
3.) AVID qualified HBA info
Page 3 of 15
Joe Conforti – Avid Technology – January 15th 2016
HP Z240 Workstation – Tower / SFF Rev A Config Guide
SFF
Slot # Electrical
Mechanical
Utilization
1 x16 PCI-E Gen 3
x16
Optional Graphics Card:
Nvidia Quadro K620 or K1200
or Local Storage HBA
Atto PCIe SAS controller
or HP Z Turbo Drive G2 PCIe Solid State Storage HBA
http://www8.hp.com/us/en/campaigns/workstations/z-turbo-drive-g2.html
2 x1 PCI-E Gen 3
x4
StarTech 1394 PCIe Firewire adapter.
Half height PCIe card (PEX1394B3) (Ports - 2 FW800 and 1 FW400).
3 x1 PCI-E Gen 3
x4
Not defined for use.
4 x4 PCI-E Gen 3
x16
Optional Intel i350-T2 Dual-port 1Gb Ethernet Adapter:
(ISIS Dual-port Connectivity)
or Local Storage HBA
Atto PCIe SAS controller
or HP Z Turbo Drive G2 PCIe Solid State Storage HBA
http://www8.hp.com/us/en/campaigns/workstations/z-turbo-drive-g2.html
Embedded Intel
i219-LM GbE NIC
Use for connectivity to Avid ISIS
Requires Windows 20.4.1 Intel ProSet Driver (see below):
Embedded Intel
HD P530 graphics
Embedded Intel HD P530 graphics are supported with Media Composer
Dedicated memory for the HD P530 graphics must be set to 1GB via the system BIOS.
x4 PCI-E Gen 3
M.2 M.2 High Performance solid state storage option
SLOT CONFIGURATION WARNING: The Z240 comes in Tower and SFF (Small Form Factor) configurations. These
configurations each use a different system motherboard. As a result there are different slot configuration guidelines for
each model. The SFF is covered in section 4 below. The Tower is covered in section 5 below.
4.) Slot Configuration For SFF [Small Form Factor] Z240:
All slots in SFF model are half length and half height
Page 4 of 15
Joe Conforti – Avid Technology – January 15th 2016
HP Z240 Workstation – Tower / SFF Rev A Config Guide
Tower
Slot # Electrical
Mechanical
Utilization
1 x1 PCI-E Gen 3
x4
StarTech 1394 PCIe Firewire adapter.
Half height PCIe card (PEX1394B3) (Ports - 2 FW800 and 1 FW400).
2 x16 PCI-E Gen 3
x16
Optional Graphics Card:
Nvidia Quadro K620 or K1200
or Local Storage HBA
(Atto PCIe SAS controller)
or HP Z Turbo Drive G2 PCIe Solid State Storage HBA
http://www8.hp.com/us/en/campaigns/workstations/z-turbo-drive-g2.html
3 x4 PCI-E Gen 3
x4
Local Storage HBA
(Atto PCIe SAS controller)
or HP Z Turbo Drive G2 PCIe Solid State Storage HBA
http://www8.hp.com/us/en/campaigns/workstations/z-turbo-drive-g2.html
4 x4 PCI-E Gen 3
x16
Optional Intel i350-T2 Dual-port 1Gb Ethernet Adapter:
(ISIS Dual-port Connectivity)
or Local Storage HBA
(Atto PCIe SAS controller)
or HP Z Turbo Drive G2 PCIe Solid State Storage HBA
http://www8.hp.com/us/en/campaigns/workstations/z-turbo-drive-g2.html
Embedded Intel
i219-LM GbE NIC
Use for connectivity to Avid ISIS
Requires Windows 20.4.1 Intel ProSet Driver (see below):
Embedded Intel
HD P530 graphics
Embedded Intel HD P530 graphics are supported with Media Composer
Dedicated memory for the HD P530 graphics must be set to 1GB via the system BIOS.
x4 PCI-E Gen 3
M.2 M.2 High Performance solid-state storage option
5.) Slot Configuration For Tower Z240:
Page 5 of 15
Joe Conforti – Avid Technology – January 15th 2016
HP Z240 Workstation – Tower / SFF Rev A Config Guide
6.) Optional add-in SAS storage controller for local SAS storage connectivity.
Suggest Atto Technology. Atto offers a wide range of SAS controllers for local SAS storage connectivity:
Some suggestions are:
Atto ExpressSAS R680 (6Gb/s SAS / SATA RAID Controller
https://www.attotech.com/products/adapters/sas-sata-raid/6gb/ESAS-R680-000%20ESAS-R680-C00
Atto ExpressSAS H680 (6Gb/s SAS / SATA Controller
https://www.attotech.com/products/adapters/sas-sata/6gb-pcie-30/ESAS-H680-000
R680 H680
7.) Optional add-in 1394 controller for 1394 camera / deck / storage connectivity.
StarTech 1394 PCIe Firewire adapter
Half height PCIe card (PEX1394B3) (Ports - 2 FW800 and 1 FW400)
http://www.startech.com/Cards-Adapters/FireWire/3-Port-2b-1a-1394-PCI-Express-FireWire-CardAdapter~PEX1394B3
Page 6 of 15
Joe Conforti – Avid Technology – January 15th 2016
HP Z240 Workstation – Tower / SFF Rev A Config Guide
8.) Various Configuration Issues:
A.) HP Z240 (Tower and SFF) System BIOS settings:
1.) Verify CPU Hyper-Threading – Enable
2.) If using the embedded Intel HD P530 graphics, set dedicated video memory to 1GB **
3.) Set Intel Turbo Mode*** – Disable (Optional, only if needed)
** Only required if using the embedded Intel HD P530 graphics. If using the Nvidia Quadro K620
or K1200 do not make this setting because it will allocate memory that will not be useable by the
system O.S.
*** Only required if connecting USB audio I/O devices. This setting will eliminate any audio
“motor-boating” or audio “popping” which may be experienced with USB audio I/O devices.
Set Z240 (Tower and SFF) required system BIOS settings:
1.) Verify CPU Hyper-Threading - Enable
- During boot up press F10 to invoke BIOS Set Up.
- Select the Advanced tab
- Select System Options
- Ensure the Hyperthreading box is enabled (Check-mark)(Should be enabled by default)
2.) If using the embedded Intel HD P530 graphics, set dedicated video memory to 1GB
- Return to the Advanced Tab
- Select “Built-In Device Options”
- Change “Video memory Size” to 1024MB (1GB) (Default is 128MB)
- Select “Save”
- Confirm “Yes” to save
3.) Set Intel Turbo Mode - Disable (Optional, only needed if there are audio “popping” problems with
attached USB audio devices)
- Select Advanced tab
- Select System Options
- Uncheck the “Turbo-boost” box
- Select Save
- Confirm “Yes” to save
- Press F10 to Save changes and Exit BIOS
Page 7 of 15
Joe Conforti – Avid Technology – January 15th 2016
HP Z240 Workstation – Tower / SFF Rev A Config Guide
AVID Software
Min Version(s)
GPU
Driver Required
Media Composer
8.4.3
Quadro K620 / K1200
Nvidia 353.82
Media Composer
8.2.5
Quadro K620 / K1200
Nvidia 347.52*
Media Composer
8.2.5
Intel HD P530
Recommend using latest
posted on HP’s website
B.) O.S. setting recommendations for optimum performance with Avid Editing applications:
The following link provides O.S. setting suggestions for ensuring optimum performance when working with
your Avid editing application with either Windows 7 or Windows 8 O.S.
http://avid.force.com/pkb/articles/en_US/troubleshooting/en390339
C.) Qualified Video Drivers:
After installation of the AVID software the supported Nvidia driver can be found in the following directory:
C:\Program Files\Avid\Utilities\Nvidia.
If a specified Nvidia driver is NOT included with the patch Avid installer, the required Nvidia driver can typically be
found on the Avid Knowledge Base.
The supported Intel HD P530 driver can be found on the H.P. support website for the Z240.
Refer to the ReadMe for driver information for the specific version of Media Composer being installed
Page 8 of 15
Joe Conforti – Avid Technology – January 15th 2016
HP Z240 Workstation – Tower / SFF Rev A Config Guide
Set optimized Nvidia driver settings for Avid editing environments:
1. See picture below
2. Right-Click on the desktop and select Nvidia Control Panel
3. Select Manage 3D Settings
4. Select “Global Settings” Tab
5. Under the “Global Settings” tab select “Base Profile”.
6. Scroll down and locate the “Power Management Mode” feature. The default setting is “Adaptive”. For
the “Power management mode” feature, select “Prefer maximum performance” as shown in the picture
below.
7. Depress the “Apply” button.
Page 9 of 15
Joe Conforti – Avid Technology – January 15th 2016
HP Z240 Workstation – Tower / SFF Rev A Config Guide
8. Set the PhysX device configuration
9. Under 3D Settings select “Set PhysX Configuration” (See picture below)
10. Under “Select a PhysX processor:” , Auto-select is currently selected.
11. See picture below
12. Under “Select a PhysX processor:” , Change the setting to Quadro K600
13. Depress the “Apply” button.
14. Nvidia driver optimization settings for Avid environments are complete
Page 10 of 15
Joe Conforti – Avid Technology – January 15th 2016
HP Z240 Workstation – Tower / SFF Rev A Config Guide
D.) Set Windows “Visual Effects” for “best performance”:
1. Right-Click on Computer icon
2. Select Properties
3. The screen below will be displayed:
4. On the left side of the screen above, locate and select “Advanced system settings”
Page 11 of 15
Joe Conforti – Avid Technology – January 15th 2016
HP Z240 Workstation – Tower / SFF Rev A Config Guide
5. The System properties window will be displayed. (Picture below).
6. Under the “Advanced” tab depress the “Settings...” button for performance.
7. The “performance Options” window will be displayed.
8. Under the “Visual Effects” tab select the “Adjust for best performance” selection. (Picture below).
9. Depress the “Apply” button
10. Reboot Windows
11. Required Windows visual performance settings for Avid environments are now complete
Page 12 of 15
Joe Conforti – Avid Technology – January 15th 2016
HP Z240 Workstation – Tower / SFF Rev A Config Guide
E.) Embedded Intel i219-LM 1G/b network interface for ISIS connectivity:
For proper operation and connectivity of the Intel i219-LM network interface with ISIS the following are required
(These settings may be made automatically by the ISIS client installer, however , verify and manually set if
needed):
1. Requires Windows 20.4.1 Intel ProSet Driver available at:
https://downloadcenter.intel.com/download/18713/Network-Adapter-Driver-for-Windows-7-
https://downloadcenter.intel.com/download/21642/Network-Adapter-Driver-for-Windows-8-
2. For the Intel i219-LM driver, under the performance settings, change the following parameters:
- Receive Buffers to 1024
- Transmit Buffers to 1024
3. The i219-LM has an ultra-low power mode that may exhibit connection issues with older switches:
a. If you boot with the cable disconnected then connect a “live” cable the link does not come
active. You have to disable/enable the adapter at the OS level to wake it.
b. If you disconnect an active link then reconnect it, it does not become active again unless
you disable/re-enable the adapter at the OS level.
4. Disable the windows firewall.
To set the Intel i219-LM Receive / Transmit buffers:
1.) Go to device manager. Under “Network adapters” select the device named “Intel Ethernet Connection i219LM”, which will be used for ISIS connectivity.
2.) Right-click, Select properties, select “Advanced” tab.
3.) Select Performance Options
Page 13 of 15
Joe Conforti – Avid Technology – January 15th 2016
HP Z240 Workstation – Tower / SFF Rev A Config Guide
Set Receive Buffers to 1024 Set Transmit Buffers to 1024
Disable Windows Firewall
Select Control Panel / System and Security / Windows Firewall / Customize Settings
Page 14 of 15
Joe Conforti – Avid Technology – January 15th 2016
HP Z240 Workstation – Tower / SFF Rev A Config Guide
Revision
Date
Name
Update
A
January 15th ,
2016
Joe Conforti
Initial Release of the Z240 Workstation Tower / SFF
configuration guide for Media Composer [Software only]
F.) Serial Port Deck Control:
The HP Z240 Tower and SFF workstation(s) do not have an embedded serial port. Serial port deck control can be
established via two methods (both of which have been qualified by Avid and will maintain frame accuracy in Avid
environments)
1. Addenda model RS-USB / 4 direct USB-to-RS422 serial adapter. This is a simple device which connects directly from a
USB 2.0 port of the Z240 directly to the RS422 port of a deck.
http://www.addenda.com/addenda-elect/products/rsUSB4.php
2. Combination of a Keyspan (Tripp-Lite) Model USA-19HS USB-to-serial-port adapter with Addenda Rosetta
Stone model RS – 2/8 RS232-to-RS422 converter
- Keyspan (Tripp-Lite) Model USA-19HS (AVID P/N 7080-20013-01)
http://www.tripplite.com/en/products/model.cfm?txtSeriesID=518&EID=13384&txtModelID=3914
- Addenda Rosetta Stone (or equivalent) model RS – 2/8 RS232-to-RS422 converter (AVID P/N
7070-00507-01)
http://www.addenda.com/addenda-elect/products/rs28.php
To connect the Keyspan 19HS / Addenda RS -2/8 combination:
- Install the Keyspan 19HS driver before plugging the device into a Z240 USB port.
- Once the Keyspan 19HS driver is installed then plug the Keyspan 19HS into a Z240 USB 2.0 port.
- The Keyspan 19HS will now show up in device driver.
- Using a serial cable, connect the 9-pin serial port of the Keyspan 19HS USB adapter to the port of the
Addenda marked RS232 from PC
- Using a 2nd serial port cable connect the port of the Addenda marked “RS422 to VTR” to the deck control
serial port of the deck.
Revision Update
Page 15 of 15
Joe Conforti – Avid Technology – January 15th 2016
HP Z240 Workstation – Tower / SFF Rev A Config Guide
Loading...