ZEDA™ Bluetooth Speaker – Instructional Manual
Thank you and congratulations on your purchase of the Avido™ ZEDA
Bluetooth Speaker. To get the most of your new product, please read these
instructions before use. Enjoy!
Avido ZEDA Features:
• Connect- Connect to the ZEDA speaker using Bluetooth, Micro SD
Card (TF Card Mode), USB Flash Drive, and the included 3.5mm
auxiliary cable.
• Watch- The built in LED lights allow your music to visually come alive.
With 9 LED settings to choose from, you will be sure to find your
favorite!
• Listen- The Avido ZEDA also includes a built-in FM radio!
• Chat- Use the Avido ZEDA as a speakerphone to make calls, answer
calls, and more.
• Voice Guidance- Commands prompts let you know current connection,
battery status, and pairing status.
What’s Included:
1. Avido ZEDA Bluetooth Speaker
2. Micro-USB Cable
3. 3.5mm Auxiliary Cable
4. Instruction Manual
Avido ZEDA Overview:
1. Tap: Mode Change (Bluetooth, FM Radio, Auxiliary Connection, TF
Card Mode, USB Input)
Press and hold: LED light mode selection
2. Tap: Next song
Press and hold: Volume Up
3. Tap: Previous song
Press and hold: Volume Down
4. Tap: Play / Pause, Answer Phone / Hang Up
5. Speaker Grill / LED Lights
6. Built-In Microphone
Avido ZEDA Overview (continued):
7. Micro-USB Input (used for charging the speaker)
8. USB Flash Drive Input
9. ON/OFF Switch
10. Auxiliary Input (3.5mm jack). Also used to improve FM Radio reception.
11. Micro-SD Card Input (TF Card)
12. LED Status Light
Avido ZEDA Power On / Off:
Turning On / Off the Avido ZEDA:
- Slide ON / Off Button to turn on the speaker
Power and Mode Selection:
Upon turning on the ZEDA speaker, the unit will check to see if any external
devices have been inserted or attached (Micro SD Card or USB Flash Drive). If
so, the unit defaults to this device.
If nothing is detected, the unit will enter “Bluetooth Mode” and a voice prompt
will let you know the current mode selection.
LED Light Modes:
The ZEDA speaker has nine LED light choices for your enjoyment. Some of
these modes dance to the beat of your music, so be sure to have music
playing when changing modes to see the full effect.
To select modes, press and hold the button. The LED light settings
will change with every press and hold.
Bluetooth Pairing:
Power on the Avido ZEDA speaker. Pairing mode is automatically enabled. On
your Bluetooth device, find “Avido Speaker” under your Bluetooth settings.
(Input 0000 if a passcode is required). A successful Bluetooth connection will
be followed by an audible notification.
*For help with Bluetooth connections, please consult your devices user’s manual.
Bluetooth Speakerphone Call:
The speakerphone function is enabled when your device is connected via
Bluetooth. Press the #4 button (Play / Pause, see diagram) to answer a call.
Press again to end the call. To decline a call without answering, press and
hold the button. For the best conversation experience, turn the speaker so
that the mic opening faces the user and keep the talking distance to the
speaker within a short distance.
FM Radio:
Tap the mode change button (#1 – see diagram) to change to FM Radio mode.
A voice prompt “FM Radio” will be heard. At this time, please insert your
auxiliary cable. The ZEDA was designed to use the auxiliary cable as an
antenna and your FM radio reception will be greatly improved.
To scan FM radio stations (required for first use in new locations), tap the play
/ pause button. Scanning will take approximately one to two minutes to
complete. After this is done, press the “<” and “>” to change stations. To
change volume, press and hold the “<” and “>” buttons.
Micro- SD (TF Card Mode):
Insert the Micro-SD (TF Card) into slot #11 (see diagram). A voice prompt “TF
Card Mode” will be heard when inserted. Press “<” and “>” to skip song
tracks. Volume controls and play / pause buttons will work normally.
USB Flash Drive Mode:
Insert a USB Flash Drive into slot #8 (see diagram). A voice prompt “USB
Flash Drive Mode” will be heard when inserted. Press “<” and “>” to skip song
tracks. Volume controls and play / pause buttons will work normally.
Line-In (Auxiliary) Mode:
Insert an auxiliary cable into slot #10 (see diagram) and the other end into your
device. Press the mode change button (#1 – see diagram) to change to
Line-In mode. Volume controls will work normally.
Charging the Speaker:
Using the included Micro-USB cable, connect the Micro-USB connector to
the speaker, and the standard USB connector to a USB power source, such
as a laptop computer or smartphone wall charger. The charging will begin and
take approximately four hours to complete for a full charge (0-100%).
Indicator Status:
- Fast Blinking Blue- Powering On
- Blue / Green- Waiting for Bluetooth Connection
- Solid Blue/ Slow Blinking Blue- Bluetooth Connected
- Solid Green- Radio Mode, Auxiliary Mode, FM Radio, TF Card Mode,
USB Flash Drive mode
Speaker Specifications:
Output Power: 6W 3W*2
Frequency: 20-180000HZ(+/-3dB)
S/N: ≥80dB
Speaker: 45mm 4Ω
Input: DC 5V
Size: 19 x 4.8 x 6.8cm
Battery Capacity: 2000mAh
Bluetooth Version: 4.0
Warranty Information:
Avido warrants this product to be free from defects in materials and
workmanship for 1-Year. If your Avido accessory is found to be defective
within that time frame, we will promptly repair or replace it. This warranty does
not cover accidental damage, wear and tear, or consequential or incidental
loss. If you are in need of warranty support, please email
info@avidopower.com.
Customer Support
Please visit our website www.avidopower.com for additional information and
support.
Avido, LLC
1-844-MY-AVIDO
www.AvidoPower.com
Loading...