AV-GAD Eye-Spy II, Eye-Spy II Quad Pet, Eye-Spy II PRO, Eye-Spy II Curtain Installation Instructions Manual

Installation Instructions

Version IV (Built-In EOL mode removed)

Eye-Spy II – Standard (w/o bracket)
Eye-Spy II PRO – With bracket
Eye-Spy II Quad Pet – With bracket
Eye-Spy II Curtain – (w/o bracket)

Item 4773

2

Preliminary Considerations

Choose the mounting location after careful
consideration of the protected area.
Locate the Eye-Spy II in a way that the intruder
will cross

the infrared beam pattern.

Do not mount the unit in direct sunlight, windy
place, near airflow, high voltage lines or close to
heat sources.

Front Cover Removal

Remove the front cover by opening the screw in
the slot between the cover and the base at the
Eye-Spy II bottom.

3

Mounting Procedure

Mount the Eye-Spy II on a flat wall or corner.
Usually corner installation provides optimal
coverage.

The Eye-Spy II special optics provides optimal
covering and range when mounted at 1.60 –

3.30 meter (5 to 12 ft) height. PCB vertical
adjustment not required. The highest installed
provides larger range, however, the optimal
height is 2 to 2.5 meters.

Figure 1: Mounting and wires entry

4

Punch out the wires entry rectangular knockout
in the Eye-Spy II base, as shown in figure 1.
Insert the cable and attach the base to the wall or
corner.
To prevent false alarm caused by insects and air
stream, seal the cable entry knockout and holes
that are not in use.

Mounting With the Swivel Bracket

The swivel bracket is used for wall mounting
only (for ceiling mount, an self-made adapter
required).
Punch out the three screws knockout (figure 1)
on the Eye-Spy II base.

Figure 2: Eye-Spy II bracket (back

view

)

5

Insert the cable through the wires entry at the
bracket wall base (figure 2).
To pull the cable from the wires outlet (figure 3)
use a small pliers.
If a fat cable is used drill a hole in the detector
upper-back to avoid the cable insert via swivel
bracket channel. Seal this hole after installation.
Install the bracket to wall (after inserting the
cable), first remove the Pan Screw from the
bracket and tighten this screw from the detector
base side. Attach the Eye-Spy II base to the
swivel bracket with the two supplied locking
screws (figure 1, 3).

Wires Outlet

Tilt Screw

Pan screw

Before attaching to PIR

remove this screw

Bracket to PIR

locking screws (2)

Figure 3: Eye-Spy II bracket

6

Terminal Connections

Wire the cable to the terminal block at the PIR
board as shown in figure 4. Wire the Tamper
switch to a separate zone, programmed at alarm
panel as tamper or 24H type.

12V DC: Power supply inputs
ALARM: N.C. contact MOS relay
TAMPER: N.C. dry contact switch

Figure 4: Eye-Spy II PCB layout

7

Printed Circuit Board

(PCB)

Adjustments

Before closing the front cover make sure to
tighten the PC Board holding screw.

QUAD PET TYPE:
Typical mounting height: 2.2 meter (7 ft).
Select the required PET mode; 18 (40 lb) or 30
kg (66 lb), refer to figure 3. It’s recommended to
install the PIR with the bracket in 5 degrees
vertical slop. The Quad Pet is useful at the most

hostile environment

.

Avoid installing the Pet PIR in front to stairway
or furniture, for preventing the pet to jump in
front of the detector and cause false alarm.

CURTAIN TYPE:
Typical mounting height: Top of the protected
window or entry. The Curtain type is “blind” on
side patterns.
The Curtain PIR application is bedrooms or
other areas where protection is required when
people are inside the protected area.

Do a walk test (described in this manual) and
readjust sensitivity and pulse count as necessary
until a desired coverage pattern is reached.

8

It’s recommended to set the Pulse jumper at 3.

Jumpers Setting (pull to remove)

LED:

To disable the LED indication, move the LED
jumper to OFF.

PULSE:

Set the PULSE jumper in position 1 or 3,
corresponding to the desired pulse count.
Highest sensitivity is at position 1. Position 3 is
recommended to prevent false alarms (lower
sensitivity). Factory default is no pulse count.

EOL MODE (Jumper Settings):

Starting Sep. 2006 the EOL option removed.

PET MODE (Eye-Spy II Quad PET only):

Quad Pet is recommended for harsh indoor areas
and sites with Pets. Pet jump towards the PIR
may cause alarm.
Set the PET jumper in position 18 for small pet,
set at 30 kg for bigger pet, not higher than 70
cm. Factory default is 18 kg.

9

Walk Test

Replace the front cover during the walk test.
Apply power and wait at least two minutes for
the detector to stabilize.
The LED is viewed through the detector lens.
Walk through the entire protected area and
observe the LED to confirm full coverage. If
the swivel is used, adjust it when necessary.
To prevent false alarms adjust sensitivity at
minimum and pulse at mode 3 setting (factory
default is mid range).

When adjustment is complete, tighten the PIR
cover screw. For Eye-Spy II with swivel
bracket, refer to figure 3; tighten the two
adjustment screws.

WARNING: Test this alarm

product at least once a week.

Av-Gad Limited Warranty

Av-Gad Systems Ltd. and its subsidiaries and affiliates
(“Seller”) warrant its products to be free from defects in
materials and workmanship under normal use for 12 months
from the date of sale.
Because Seller does not install or connect the product and
because the product may be used in conjunction with products

10

not manufactured by Seller, Seller can not guarantee the
performance of the security system which uses this product.
Seller’s obligation and liability under this warranty is
expressly limited to repairing or replacing, at Seller’s option,
within a reasonable time after the date of delivery, any
product not meeting the specifications.

SELLER MAKES NO OTHER WARRANTY, EXPRESSED OR
IMPLIED, AND MAKES NO WARRANTY OF
MERCHANTABILITY OR OF FITNESS FOR ANY PARTICULAR
PURPOSE.

IN NO CASE SHALL SELLER BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH
OF THIS OR ANY OTHER WARRANTY, EXPRESSED OR
IMPLIED, OR UPON ANY OTHER BASIS OF LIABILITY
WHATSOEVER.

Seller’s obligation under this warranty shall not include any
transportation charges or costs of installation or any liability
for direct, indirect or consequential damages or delay.

Seller does not represent that its products may not be
compromised or circumvented; that the product will prevent
any personal injury or property loss by burglary, robbery, fire
or otherwise; or that the product will in all cases provide
adequate warning or protection.
Buyer understands that a properly installed and maintained
alarm may only reduce the risk of burglary, robbery or fire
without warning, but it is not insurance or a guarantee that
such will not occur or that there will be no personal injury or
property loss as a result.

CONSEQUENTLY, SELLER SHALL
HAVE NO LIABILITY FOR ANY PERSONAL INJURY, PROPERTY
DAMAGE OR OTHER LOSS BASED ON A CLAIM THAT THE
PRODUCT FAILS TO GIVE WARNING. HOWEVER, IF SELLER IS
HELD LIABLE, WHETHER DIRECTLY OR INDIRECTLY, FOR
ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED
WARRANTY OR OTHERWISE, REGARDLESS OF CAUSE OF
ORIGIN, SELLER’S MAXIMUM LIABILITY SHALL NOT IN ANY
CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT,
WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY
AGAINST SELLER.

11

No employee or representative of Seller is
authorized to change this warranty in any way or
grant any other warranty.

WARNING: This product should be tested at least
once a week.
======================================

Standards

The EYS II Conforms to European Union (EU) Electro
Magnetic Compatibility (EMC) Directive number
89/336/EEC (amended by 92/31/EEC & 93/68/EEC).
The CE mark indicates that this product complies with
the European requirements for health, environmental,
safety, and customer protection.

12

ESY II Specifications

Sensor: Dual and Quad (Pet type) element
Processor: Digital ASIC with analog channel
Operating Voltage: 8.4 to 16V DC
RF Immunity: From 50kHz to 1GHz at 50V/m.
Current: 7 mA at 12 volts (with LED off)
Alarm Contacts: 0.1 amps @ 24V DC, N.C. (S.

State)

Tamper Contacts: 0.5 amps@ 24V DC, N.C.
Range: 15 meters @ 20 ° C, 3 m high
Size without swivel: 7.7 x 6.6 x 3.9 cm (3.0 x 2.6 x 1.5“)

Swivel Bracket Adjustment:

Horizontal (tilt): ± 25° Vertical (pan): +5°, -15°

Optical Filtering:

White light protection, pigmented lens
Operating Temperature: -10 to +50oC (+14 to
+122

o

F)

Temperature Compensation: Automatically
Storage Temp. : -20 to +60oC (-4 to +140

o

F)

Eye-Spy II is a registered trademark of
Av-Gad Systems Ltd.



Av-Gad systems Ltd., EYE-SPY II, VER 4, 11/2008

http//www.av-gad.com

Item 4773