04/02 Rev. 2.15-01 MANUAL Page 1
TTX 207 – Da Capo
Setup, Operation, Service
General notes ............................................... 2
Before usin
g
the printer.... ......................... 2
Cop
yrig
ht ................................................... 2
Initiation ......................................................... 3
Unpackin
g
the printer ................................ 3
Settin
g
up and connecting the printer ....... 3
Connections .................................................. 4
Insertion/removal of material ......................... 5
Operation ...................................................... 6
Connectin
g
to a computer / starting .......... 6
Functions of displa
y
keys .......................... 6
Functions of LED elements ....................... 6
Ad
j
ustment of DIP switches ...................... 7
Maintenance and care .................................. 8
Chan
ging
and cleaning the printhead ....... 8
Cleanin
g
the feed roller ............................. 9
Cleanin
g
of gap sensor ............................. 9
Cleanin
g
of material guiding parts ............. 9
Label material ............................................. 10
Trouble shootin
g
..........................................11
Status Printout ............................................. 13
Sensor Check Routine ................................13
Access to routine .....................................13
Gap sensor ..............................................13
Micro switch/printhead lever ....................13
Material end sensor .................................13
Technical Specifications ..............................14
Anhan
g
/ Appendix ......................................16
Zeichensatztabelle / Font table ................16
Linien und Rechtecke / Lines and rectan
g
les
17
Interne Fonts / Internal fonts ....................18
Interne Barcodes / Internal bar codes ......21
Index ............................................................22
04/02 Rev. 2.15-01 MANUAL Setup, Operation, Service, page 2
TTX 207 – Da Capo
General notes
Before using the printer....
The following warning hints and precautions contained in these Operating Instructions must be strictl
y
observed. This will considerably contribute to the
safe and expert opera tion of
y
our printer.
Exclusively original parts and accessories available from the manufacturer
are to be used in order to maintain the service life of
y
our prlnter. The use of
parts not in compliance with the exactin
g
demands made by the manufactu-
rer ma
y
result in unnecessary sources of troubles.
The housing of the unit must exclusively be opened by authorized technical
personnel onl
y
.
Insertion/Exchange material should be carrled out only by especially instructed personnel (Set Up Mode!).
On operation with open cover, fingers, hair, clothes, jewelry, etc. may be
cau
g
ht by and get into the unit in the print modul.
At a material width less than 65 m the thrust screw has to be tightend.
Release printhead by opening the pressing lever during longer periods of no
operation.
Wait at least 10 seconds before switching unit back „ON“.
Do not remove, insert or exchange PLUG IN CARDS until after at least 60
seconds from switchin
g
„OFF“ the device.
Copyright
This User Manual and its contents are subject to copyright. The publisher‘s
prior written consent must be obtained for reproduction of the Manual as a
whole or part thereof.
Aver
y
reserves the right to technical and other alterations without prior notice.
04/02 Rev. 2.15-01 MANUAL Setup, Operation, Service, page 3
TTX 207 – Da Capo
Initiation
Unpacking the printer
1. Remove top foamed packing.
2. Take printer out of cardboard box.
For carrying your printer, take it by the ba se plate.
Front cover, reel holder and motor of optional knife must not be used as carr
ying
handles.
Setting up and connecting the printer
1. Check mains voltage setting and fuses.
– The fuses can be replaced b
y
removal of the fuse element (Fig. 1).
–Mains volta
g
e variation is possible by turning the insert.
2. Insert current suppl
y
into lining designated for this purpose at the rear side
of unit.
3. Switch „ON“ of unit.
CAUTION!
Mains volta
g
e can kill you!
– Pull off the mains connector befor you check or change the mains voltage
setting!
– Pull off the mains connector befor you check or replace the fuse!
04/02 Rev. 2.15-01 MANUAL Setup, Operation, Service, page 4
TTX 207 – Da Capo
Connections
All connectors are located at the rear side.
A Centronics or alternativel
y
a serial V.24/DB 25 (RS232) interface interface
is inte
g
rated.
Before connecting/disconnecting the interface cable and the stacker switch
„OFF“ all dev i ces.
Only devices may connected to the interface and stacker connector which
are approved to ICE 950 and VDE 0805 and are in compliance to SELV.
Fig. 1: Connections on the printer backside.
(not supported)
04/02 Rev. 2.15-01 MANUAL Setup, Operation, Service, page 5
TTX 207 – Da Capo
Insertion/removal of material
1. Hang document material in reel holder in a way to ensure anticlockwise
unwindin
g
.
2. Open pressure lever (red).
3. Insert material underneath the printhead accordin
g
to sketch, further mate-
rial transport is automaticall
y
.
4. Close pressure lever.
5. When usin
g
notched material, adjust gap sensor to the gap position.
At a material width less than 65 m the thrust screw (Fig. 2) has to be tightened.
6. Switch „ON“ printer - the
g
reen LED glows at the operation panel (eventually
switch to OFFLINE). B
y
depression of the FEED-key a material feed can be
advanced. At punched material one label len
g
th is advanced, continous
material is transport as lon
g
as FEED-key is operated.
Removal of material
Material can be removed after openin
g
the pressure lever.
Fig. 2: Material winding diagram.
CAUTION!
Dan
g
er of pulling in and tearing off of hair, jewellery, loose clothing, etc.!
– Don´t let long hair, loose sleeves, jewellery, etc. hang into the printer!
04/02 Rev. 2.15-01 MANUAL Setup, Operation, Service, page 6
TTX 207 – Da Capo
Operation
Connecting to a computer / starting
1. Connect interface cable from computer to the printer. Switch on the printer,
the
g
reen LED glows (LED = small, round light emitting element).
2. B
y
depressing the ON/OFF key, the printer is switched to „ONLINE mode“,
the
y
ellow LED glows and the printer is ready to receive data and to print
labels.
Functions of display keys
ON / OFF
– Switch to the ONLINE or OFFLINE mode. ONLINE mode is indicated b
y
the
y
ellow LED, the unit is ready to receive data.
– Control break of a print
j
ob, the yellow LED flashes fast - rest quantity!
– If an error is indicated (red LED) the error will be confirmead after its cor-
rection b
y
depressing the ON/OFF key.
FEED
– In the OFFLINE mode a material feed can be advanced. At punched ma-
terial one label len
g
th is advanced, continous material is transport as long
as FEED-ke
y
is operated.
– If an error is indicated the error code ma
y
be called off via the yellow LED
– The controlled break of a current print
j
ob will be cancelled.
CUT
Reserved for optional functions.
Functions of LED elements
The operation panel shows 3 LED‘s in order to indicate the operation modes.
POWER
(Green) This LED
g
lows, if printer is switched on.
ERROR
(Red) Indication of an error (end of media........)
DATA
(Yellow) LED
g
lows if printer is switched to ONLINE mode.
– LED flashes if unit prints, receives data or
g
enerates an image.
– LED flashes fast if current print
j
ob is interrupted - rest quantity!
– Indication of error code with 5 short/lon
g
flash signals called off by pressing
the FEED ke
y
.
04/02 Rev. 2.15-01 MANUAL Setup, Operation, Service, page 7
TTX 207 – Da Capo
Adjustment of DIP switches
Left of the mains plug there are located 8 DIP switches (Fig. 1) with which the
parameters ma
y
adjusted as follows.
A modification of a DIP switch position will be effictive after newly switching
„ON“ the device.
Fig. 3: DIP switch settings.
Loading...