®
Monarch
®
1115®Labeler
Operating Instructions
TC1115OI Rev. BE 12/07 ©2006 Paxar Americas, Inc.
a subsidiary of Avery Dennison Corp. All rights reserved.
LOADING LABELS & SETTING PRINT BANDS
LOADING LABELS
1
Slide label roll between hubs.
Discard first fourteen labels
and backing paper.
2
Squeeze operating lever and feed
label strip over spring and under brake
wheels until about twelve labels come out.
3
Feed label strip up under plate until
two labels come out. Rewind
label roll until loop is removed.
4
Pull backing paper to the end of the
operating lever, separating labels from
backing paper.
5
Tear backing paper evenly
between cuts, close to the end of the
strip as shown.
6
Hold labeler upside down and while
squeezing operating lever, feed
backing paper into slot. Squeeze operating
lever eight times until backing paper comes
through the rear exit.
7
If backing paper does not become
taut and exit at rear: Turn labeler
upside down, squeeze operating lever and
pull backing paper out of slot. Repeat
steps, 4, 5, and 6.
SETTING PRINT BANDS
1
Pull the knob until the
indicators point to
the desired band.
4
Print a sample label to insure
information is correct.
2
Turn the knob untill the indicators
point to desired character or blank.
5
If the character prints UPSIDE
DOWN, turn the band until you can
read the characters correctly. The desired
character may be coated with ink.
3
Set all bands and push the knob
in all the way.
INKING
1
Move two latch buttons toward
label roll and swing top cover
away from print head.
2
Fold a piece of scrap backing
paper.
3
Insert folded backing paper
between ink roll and carrier.
Pull to snap old ink roll free.
4
Cut off end of ink roll package.
Using package to protect fingers,
slide carrier into package and snap new ink roll
into carrier.
5
Snap top cover closed.
Hang for easy reference.
Brake
Wheels
Label Exit
Operating
Lever
Label Exit
Loop
Plate
Hub
Backing
Paper
Discarded
Labels
Slot
Backing
Paper Exit
Knob
Indicator
Blank Print
Positions
Top Cover
Latch
Button
INKING
Cap
End
Carrier
OPERATION
1
Squeeze and release operating lever.
2
Place black rollers on item to
be labeled.
3
Pull labeler to apply label.
(Gentle wiping motion.) DO NOT POUND labeler when
applying labels.
REMOVING SUPPLIES
1
Tear label strip at label roll as
shown and pull label roll from
between hubs.
2
Tear backing paper strip.
Pull label strip from labeler.
3
Squeeze and release operating
lever until backing paper is free
to be pulled out.
MAINTENANCE
1
With label roll removed, check
label track and backing paper
track for stray labels.
2
Clear label track by squeezing
operating lever and feeding label
removal strip under brake wheels and out
front of labeler.
3
To clear backing paper track:
a. Insert label removal strip in end of
track to loosen stray labels.
b. Insert label removal strip as
shown, using corner to remove stray
labels.
LUBRICATION PRINT ADJUSTMENT
If adhesive buildup occurs, lubricate as shown
with labels loaded.
1
Print location is correct when extreme
right-hand and left-hand characters are located
as shown.
Monarch lubricant is recommended.
2
Place small coin in feedwheel button slot.
3
Push feedwheel button IN COMPLETELY
and turn slightly clockwise if print is too far left or
slightly counterclockwise if print is too far right.
Adjustment made without completely depressing button
are temporary.
4
Repeat steps 2 and 3 until print is correctly
located.
TROUBLESHOOTING
Black
Rollers
Pull Strip
Tear Backing
Paper
Tear
Brake
Wheels
Front
Exit
Removal
Strip
End of
Track
OPERATION, REMOVING SUPPLIES & MAINTENANCE
Feedwheel
Button Slot
Approx. 1/16 inch (1.6 mm)
Approx. 1/16 inch (1.6 mm)
Lubricate:
One drop each spot on
backing paper (total of
four drops). Spread
with finger.
Lubricate:
One drop each side of label
chute between spring and
backing paper.
DO NOT OVER
LUBRICATE!
Visit www.paxar.com for sales, service, supplies, information, and telephone
numbers of our locations throughout the world.
TOLL FREE:
1-800-543-6650 (In the U.S.A.)
1-800-263-4650 (In Canada)
Trouble Remedy
Characters not printing.
Bands not inked.
Check ink roll per Inking
instructions.
Labels feed slowly or
hesitantly.
Follow Lubrication and
Maintenance Instructions.
Labels will not feed. Reload per instructions. Use
correct supplies.
Follow Maintenance instructions.
Print incorrectly located. Follow Print Adjustment
instructions.
Printing smeared or
distorted.
Print several labels (15 to 25) to
use up excess ink.
Printing too light. Squeeze operating lever harder
during operation.
Warranties
Product warranty statements may vary from country to
country. Please contact the authorized PAXAR/Monarch
representative in your country for details.
LUBRICATION, PRINT LOCATION, & TROUBLESHOOTING
Loading...