Operator's
Handbook
®
FRESHMARX
9415™
Labeling System
©2007 Avery Dennison Corp. All rights reserved.
28028 28028
0 0
TC9415OH Rev. AK 8/11
Each product and program carries a respec tive written
warranty, the only warranty on which the customer can
rely. Avery Dennison reserves the right to make changes in
the product, the programs, and their availability at an y time
and without notice. Although Avery Dennison has made
every effort to provide complete and accura te information
in this manual, Avery Dennison shall not be liable for any
omissions or inaccuracies. Any update will be incorporated
in a later edition o f this manual.
©2
007 Avery Dennison Corporation. All rights reser ved. No
part of this publication may be r eproduced, transmitted,
stored in a retrieval s ystem, or translated into any
language in any form by any means , without the prior
written permission of Avery Dennison .
WARNING
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
CANADIAN D.O.C. WARNING
This digital apparatus does not exceed the Class A limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the Canadian
Department of Communications. Le présent appareil numérique n’émet pas de
bruits radioélectriques dépassant les limites applicables aux appareils numériques
de la classe A prescrites dans le Réglement sur le brouillage radioélectrique édicte
par le ministère des Communications du Canada.
Trademarks
FreshMarx® and 9415 are registered trademarks of Avery Dennison Corporation.
Avery Dennison
170 Monarch Lane
Miamisburg, OH 45342
TABLE OF CONTENTS
GETTING STARTED ............................................................1-1
Using This Manual.........................................................1-1
Audience ......................................................................1-1
Unpacking the Printer....................................................1-2
Installing the Printer ......................................................1-3
Connecting the Printer’s Power Supply............................ 1-4
Loading Labels .............................................................1-5
PRINTING LABELS ............................................................. 2-1
About the Printer...........................................................2-2
Calibrating the Touch Screen ......................................... 2-3
Printing Freshness Labels ..............................................2-4
Reprinting a Label ......................................................... 2-6
Printing Use First Labels ................................................2-8
Sleep Mode..................................................................2-8
CARE & MAINTENANCE...................................................... 3-1
Clearing Label Jams...................................................... 3-2
Cleaning the Platen Roller and Printhead......................... 3-3
Cleaning the Touch Screen Display................................. 3-5
Cleaning the Printer ......................................................3-5
TROUBLESHOOTING .......................................................... 4-1
Technical Support.........................................................4-3
Printing a Diagnostics Label........................................... 4-4
LABEL FORMATS ..............................................................A-1
Format 1 ..................................................................... A-1
Format 2 ..................................................................... A-2
Format 3 ..................................................................... A-3
Format 4 ..................................................................... A-4
Format 5 ..................................................................... A-5
Format 6 ..................................................................... A-6
Format 7 ..................................................................... A-7
Format 8 ..................................................................... A-9
SPECIFICATIONS .............................................................. B-1
Printer Specifications ................................................... B-1
Supply Specifications................................................... B-1
i
ii Operator’s Handbook
GETTING STARTED
1
Use the FreshMarx® 9415™ Labeling System
for product freshness and to label inventory. This
system is available as a single or dual printer.
Information in this documen t supercedes information
in previous versions. Check our We b site for the latest
documentation and rel ease information.
Using This Manual
Following is a summary of the con tents of this manual:
Chapter Contents
1 Getting Started
Unpacking and installing the
printer and loading supplies .
2 Printing Labels
Selecting and printing freshness
labels.
3
Care &
Maintenance
Clearing supply jams and
cleaning the printer.
4 Troubleshooting
Common problems and their
solutions.
A Label Formats Format sizes and content fields .
B Specifications Printer and supply
specifications.
Audience
The Operator's Handbook is for the person who prints
and applies labels.
Getting Started 1-1
Unpacking the Printer
After you unpack the prin ter, you should have the
following:
9415 printer
power supply and cord
4 wall anchors
wall mount template
Keep all packaging material in case you need to move
or return the printer.
Caution: Do not touch the electrical connectors
while setting up the printer. Static
electricity can damage or destroy the
electronic components .
1-2 Operator’s Handbook
Installing the Printer
To install the printer on the wall:
1. Select a suitable locati on for the printer on a wall.
2. Tape the wall mount templ ate to the wall in the
selected location.
Caution: The template must be level or the printer
will not install correctly.
3. Install the four wall an chors according to the four
outside holes indicated on the templ ate.
Mounting holes in back of printer
4. Remove
the template.
5. Lower the supply door on the printer so you can
see the mounting hol es on the back of the printer.
6. Attach the printer to the wall anchors using the
corresponding holes on the back of the printer.
7. Press down firmly on the print er to lock it in place.
8. Close the supply door.
Getting Started 1-3
Connecting the Printer’s Power Supply
To connect the power supply to the printer:
1. Turn off the printer. Press the power switch on
the side of the printer to the off (O) position.
2. Place the power supply in a suitable location,
preferably on a table, near an electrical outlet.
3. Plug the three-hole end of the AC adapter cable
into the three-pronged outlet in the printer’s power
supply.
4. Plug the L-shaped end of the power supply cable
into the socket on the side of the printer.
L-Shaped
Connector
Power socket
5. Plug the three-pronged end of the AC adapter
cord into a grounded elec trical outlet.
Warning: The printer and power supply should
never be operated in a loca tion where
either one can get wet. Personal injury
could result.
1-4 Operator’s Handbook
Loading Labels
1. Dual printer: Printer 1 is located on the le ft and
Printer 2 is located on the right. Printer 1 is the
default printer for all categories and formats.
2. Single printer: Printer 1 (located on the left) is
the only available printer. There is no option to
assign a format to a printer.
3. The first time you lo ad the printer after receiving it
you must remove and discard the thermal paper
from the printer slots.
4. Turn on the printer. Press the power switch on the
side of the printer to the on (I) position.
5. Press to remove the thermal paper from the
printer, if necessary.
6. Remove and discard the tape from a new roll of
labels.
7. Lower the supply door.
8. Slide a roll of labels onto the supply holder.
If necessary, adjust the supply hol der guide so it
touches the roll.
9. Feed the labels, printin g side up, into the supply
slots in the supply door.
Note: Make sure no label adhesive is exposed when
loading labels. This caus es jams.
Getting Started 1-5
10.
Make sure the supply clip is in the correc t position
to touch the edge of the supply. This clip guides
the labels through the supply slot so they do not
shift while printing.
Dual printer shown
Supply clip
Printer 2
Printer 1
Supply slot
Supply Holder
Guide
11. Close the supply door.
The printer calibrates the labels automatically.
1-6 Operator’s Handbook
PRINTING LABELS
2
This chapter describes ho w to
use the application
calibrate the touch scre en
print freshness labels
print Use First labels.
Note: You may have a custom applic ation that
differs slightly from the examples in this
manual. The screens and labels shown are
for reference only.
Printing Labels 2-1
About the Printer
The printer has a touch sc reen, five control buttons,
and, depending on your model, one or two printers.
Printer 1
Printer 2
(dual printer only)
T
he five control buttons are located on the right side
of the touch screen.
Button Action
Stops/cancels the current print j ob.
Advances supply for the selected
printer.
or
Selects which printer feeds the
supply.
Printer 1 is located on the left side.
Printer 2 is located on the right side.
Note: In the single printer version,
these buttons do n ot function.
Enters the printer configuration me nu.
2-2 Operator’s Handbook
Loading...