How it Works
avertXX
Loading...
H
Loading...
Loading...
HD6012-RW
User Manual
47 pgs760.72 Kb0

avertXX HD6012-RW User Manual

Download
HD6012-RW
2MP Low Profile IR In-Ceiling Dome Camera With WDR
User Manual
2
Indoor Drop Ceiling IP Camera (HD6012-RW) User Manual
Manual Edition 35286AA – DECEMBER 2016
©2015, AVERTX All Rights Reserved.
No part of this documentation may be reproduced in any means, electronic or mechanical, for any purpose, except as expressed in the Software License Agreement. AvertX shall not be liabl e for technical or editorial errors or omissions contained herein. The information in this document is subject to change without notice.
The information in this publication is provided “as is” without warranty of any kind. The entire risk arising out of the use of this information remains with recipient. In no event shall AVERTX be liable for any direct, consequential, incidental, special, punitive, or other damages whatsoever (including without limitation, damages for loss of business profits, business interruption or loss of business information), even if AVERTX has been advised of the possibility of such damages and whether in an action or contract or tort, including negligence.
This documentation is copyrighted. All other rights are reserved to AVERTX. AVERTX, and AvertX, are registered trademarks of AVERTX in the United States and elsewhere; Windows, and Windows XP Embedded are registered trademarks of Microsoft Corporation. All other brand and product names are trademarks or registered trademarks of the respective owners.
AVERTX Spokane, WA ● U.S.A.
4
Important Safeguards
1. Read Instructions Read all of the safety and operating instructions before using the product.
2. Retain Instructions Save these instructions for future reference.
3. Attachments / Accessories Do not use attachments or accessories unless recommended by the appliance manufacturer as they may cause hazards, damage product and void warranty.
4. Installation Do not place or mount this product in or on an unst abl e or improperly supported location. Improperly installed product may fall, causing serious injury to a child or adult, and damage to the product. Use only with a mounting device recommended by the manufacturer, or sold with the product. To insure proper mounting, follow the manufac turer's instructions and use only mounting accessories recommended by manufact urer.
5. Power source This product should be operated only from the type of power source indicated on the marking label.
Precautions
Operating
• Before using, make sure power supply and others are properl y connected.
• While operating, if any abnormal condition or malfunction is observed, stop using the
camera immediately and then contact y our local dea ler.
Handling
• Do not disassemble or tamper with parts inside the camera.
• Do not drop or subject the camera to shock and vibration as this can damage camera.
• Care must be taken when you clean the clear dome cover. Scratches and dust will
ruin the image quality of your camera. Do not use strong or abrasive deter gent s when cleaning the camera body. Use a dry cloth to clean the camera when it is dirty. In case the dirt is hard to remove, use a mild detergent and wipe the camera gently.
Installation and Storage
• Do not install the camera in areas of extreme temperatures in excess of the allowable range. (14°F~ 122°F / -10°C ~ 50°C)
• Avoid installing in humid or dusty places. The relative humidity must be below 90%.
• Avoid installing in places where radiation is present.
• Avoid installing in places where there are strong magnetic fields and electric signals.
• Avoid installing in places where the camera would be subject to strong vibrations.
• Never face the camera toward the sun. Do not aim at bright objects. Whether the
camera is in use or not, never aim it at the sun or other extremely bright objects. Otherwise the camera may be smeared and dam age d.
Regulation
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Compliance is evidenced by written declaration from our suppliers, assuring that any potential trace contamination lev els of restric ted sub sta nce s are below the maximum level set by EU Directive 2002/95/EC, or are exempted due to their application.
6
Warning
DANGEROUS HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Caution
TABLE OF CONTENTS
Table of Contents ..................................................................................... 7
Introduction ............................................................................................ 10
Overview ....................................................................................................................... 10
Product Features ...................................................................................................... 10
Getting Started ....................................................................................... 11
Box Contents ................................................................................................................ 11
Camera Overview ......................................................................................................... 12
Camera Diagram ...................................................................................................... 12
Camera Dimensions ................................................................................................. 13
Connections .............................................................................................................. 14
Indoor Cameras ................................................................................................... 14
POE Power Source .......................................................................................... 14
12vDC Power Source ...................................................................................... 15
Ports and Connections ......................................................................................... 16
External Connections ........................................................................................... 16
Locate Camera ....................................................................................... 17
AvertX Network Camera manager ................................................................................ 17
Installation ................................................................................................................. 17
Starting Network Camera Manager .......................................................................... 17
Camera Configuration ................................................................................................... 18
Device Addressing .................................................................................................... 18
Finding Network Devices ..................................................................................... 18
Viewing a Network Camera.................................................................................. 19
Connecting to the Camer a ............................................................................................ 20
Resetting the Camera ............................................................................................... 20
Administrator/User Pri vi leges ................................................................................... 20
Connecting Over the Internet ................................................................................... 21
Viewer Software ............................................................................................................ 22
Viewer Tabs .............................................................................................................. 22
Live .......................................................................................................... 23
Setup ....................................................................................................... 24
System Setting .............................................................................................................. 24
Camera Name .......................................................................................................... 24
IP Address ................................................................................................................ 24
8
Get IP an Address Automatically (DHCP) ............................................................ 25
Use Static IP Address .......................................................................................... 25
IPv6 Address Configuration ............................................................................. 26
User Setup ................................................................................................................ 26
Admin Password .................................................................................................. 26
Add User .............................................................................................................. 26
Delete User .......................................................................................................... 26
Modify User .......................................................................................................... 27
File Location ............................................................................................................. 27
Picture Setting .............................................................................................................. 28
Picture Setup ............................................................................................................ 28
Camera Tab ......................................................................................................... 28
Exposure .............................................................................................................. 28
White Balance ...................................................................................................... 28
Picture Adjustment ............................................................................................... 29
Motion Detection ....................................................................................................... 29
Add Detection Window ......................................................................................... 30
Delete Motion Detection Window ......................................................................... 30
Motion Window ................................................................................................ 30
Stream Settings ........................................................................................................ 31
Video Resolution .................................................................................................. 31
Video Orientation ................................................................................................. 32
GOP Size ............................................................................................................. 32
H.264 Profile ........................................................................................................ 32
Video Frame Rate .................................................................................................... 32
Video Compression .................................................................................................. 33
Advanced ................................................................................................ 34
System Setting .............................................................................................................. 34
Network Setup .......................................................................................................... 34
DDNS ................................................................................................................... 34
Network Advanced ................................................................................................... 34
QoS ...................................................................................................................... 34
SNMP Settings ..................................................................................................... 35
UPnP (Universal Plug N’ Play) ............................................................................. 35
Network Security ...................................................................................................... 35
HTTP .................................................................................................................... 35
IP Filtering ............................................................................................................ 35
IEEE 802.1XSEAP-TLS ....................................................................................... 35
Alarm Application ...................................................................................................... 36
Tampering and Network Failure Detection ............................................................... 37
Mail, HTTP and FTP Setup ...................................................................................... 38
SD Card .................................................................................................................... 38
Network Share .......................................................................................................... 39
Recording Schedul e ................................................................................................. 40
Recording ............................................................................................................. 40
Schedule .............................................................................................................. 41
Interval Recording ................................................................................................ 41
Maintenance ............................................................................................................. 42
Configuration ........................................................................................................ 42
Factory Default ..................................................................................................... 42
Software .................................................................................................................... 43
Picture Setting .............................................................................................................. 43
Video Mask ............................................................................................................... 43
Hot Spot .................................................................................................................... 43
Text Overlay ............................................................................................................. 43
Streaming Setting ......................................................................................................... 44
Audio ......................................................................................................................... 44
Logout ..................................................................................................... 44
Specifications ................................................................................................................ 45
Camera Specifications .................................................................................................. 45
32910AC
INTRODUCTION
OVERVIEW
The AvertX IP Mini Dome cameras are capable of providing real time streaming video with smooth image quality. The IP Mini Dome cameras offer quad streaming and can be used in a variety of installations including shops, stores, banks, parking lots, factories and for building surveillance.
With Power over Ethernet (PoE) the need for separate power lines is eliminated and cabling and installation co sts can be signif icantly reduced. The light weight, small size, and large degree of rotation of the IP Mini Dome facilitates quick and simple installation on either the ceiling or walls of structures or vehicles.
Product Featur e s
ONVIF Compliant, Profile S  1080p (2 MP) Resolution  30fps at All Resolution  Simultaneous Dual-Stream  1/2.8” CMOS Sensor  4 mm Lens  True Day/Night with IR Cut Filter  True Wide Dynamic Range  3D-DNR (3D Digital Noise Reduction)  Motion Detection  1 Sensor Input, 1 Sensor Output  Micro SD/SDHC Card Slot (Card Not Included)  Power Over Ethernet (PoE) & DC12V
GETTING STARTED
BOX CONTENTS
Before proceeding, please ch e ck that the box contains the items listed here. If any item is missing or has defects, DO NOT install or operate the product and contact your dealer for assistance.
Camera Dome Cover and Deco Rings
Quick Start Guide Mounting Template Sheet
Screws and Plastic Anchors x 2 Audio Alarm Cable
Power Cable
12
CAMERA OVERVIEW
Before installing or connecting the dome camera, please refer to this section and complete preparations for dome setup and all switch settings.
Camera Diagram
Lens
Magnetic plate
Tilt
Stopper Screw
Body
Mounting bracket
Camera Dimensions
Height: 4.5”
Width: 3.56”
14
Connections
Indoor Cameras
The camera is compatible with 12vDC and Power over Ethernet (PoE). Connect power to the camera using the provided power connector lead or connect the camera to a PoE power source. If you are connecting 12vDC power, verify the polarity of the power connection. If you are using PoE, make sure the Power Sourcing Equipment (PSE) is in use in the network.
Check the status of the network connection by looking at the link indicator and activity indicator LEDs. If the LEDs are not lit check your network connection. The green link LED indicates a network connectio n and the oran ge activity LED flashes to indicate network activity.
POE Power Source
PoE allows for the transmission of power and data via a single Ethernet cable. PoE eliminates the need for multiple cables to support power and recording. Follow the installation below to connect the camera to a PoE-enabled switch using an Ethernet cable.
12vDC Power Source
If PoE is not being used, a power adapter is needed to power the camera. An additional 12vDC connector cable is required.
16
Ports and Connections
External Connections
The camera eight pins for alarm and audio input and output. These are labeled on the rear of the camera. Each camera has an included connector with cables that can be used to connect audio and alarm devices.
Reset Button
12vDC Power
Network PoE Port
External
Connections
microSD card slot
Audio In
Audio Out
Alarm In
Alarm Out
LOCATE CAMERA
AVERTX NETWORK CAMERA MANAGER
AvertX Network Camera Manager is a software tool that allows you to quickly and easily connect and configure your AvertX IP Cameras. This software allows you to assign IP addresses, manage users, configure video settings, and update firmware on multiple cameras at once.
The Network Camera Manager software is pre-installed on all AvertX Recorders, and included on the software CD with all AvertX IP cameras. It is also available for download on the AvertX website.
Installation
You can install Network Camera Manager on any personal computer (PC) or laptop using the software CD included with your AvertX IP camera or by downloading the program from Avertx.com.
Note Network Camera Manager will only work on PCs or laptops that use a Windows
operating system. It is compatible with Windows XP, Vista, 7, and 8.
Starting Network Camera Manager
After installing the program on your PC or laptop, open the program to begin configuring your cameras.
To access Network Camera Manager on an AvertX recorder, you must operate the recorder in Windows Mode.
1. In the Live Screen, click Exit.
2. Click Restart in Windows Mode.
3. Click OK.
4. Double-click Network Camera Manager.
18
CAMERA CONFIGURATION
Device Addressing
The functions on the Device Addressing tab allow you to find, configure, and view network cameras.
Finding Network Devices
1. Click Find Devices on the Device Addressing tab.
2. To narrow your search by Camera Model, Project, or Camera Name, select
your desired criteria from the appropriate lists.
Viewing a Network Camera
1. To view a network camera over the web using the camera’s viewer software,
double-click the name of the camera.
2. Click Browse.
3. Enter the Username and Password for the camera. The username and
password are case sensitive. It is strongly recommended that the password be changed after the initial setup to prevent una uthorized access. The default username and password for AvertX IP cameras are as follows.
Username – Admin Password – 1234
4. The viewer software is now opened in Internet Explorer.
Note The viewer software will install automatically the first time you connect to the
camera. If your internet browser does not install the viewer software, check the security settings or ActiveX controls and plug-in settings. If your internet browser asks for permission to install the ActiveX control, you must allow the ActiveX control to continue the installation. If you are prompted to allow an add-on, click Allow.
5. You can now configure your camera using the Viewer Software. For more
information on using Viewer software, please see the user manual for your camera.
20
CONNECTING TO THE CAMERA
1. Locate the camera on the IP Finder list.
2. Double-click the camera to open the Viewer software in your web browser.
3. Click Browse in the pop-up window.
4. Log in to the camera with the appropriate User Name and Password.
Note The default User name is admin and the default Password is1234. The
username and password are case sensitive.
Resetting the Came ra
If it is necessary to reset the camera to the factory default settings, hold down the Reset button (see Camera Overview) for 30 seconds. This will return all settings, including network setup, to the factory default.
Administrator/User Privileges
The Administrator account has the authority to configure the IP camera and authorize users’ access to the camera. The User accounts have access to the camera with limited authority.
Connecting Over the I nt er net
There are some challenges with connecting to AvertX IP cameras over WAN (internet) connections because the camera streams video over RTSP. RTSP is an excellent protocol for media and is now used on many IP cameras (including AvertX) as the default streaming option.
RTSP, however, is not suitable for transmission between two locations that are behind different routers. In this case, the client (for example, the AvertX HVR or NVR server software) connects to the camera, and then requests a stream. The camera uses that connection to return a stream, but since the connection originated on the client side and has now switched to the camera (remote) side, the router does not have any way to determine where the traffic should be routed, so no video appears at the recorder. There are three solutions to this.
1. Connect modems on both sides directly to the recorder and camera. If there is no
router, no network address translation is needed.
2. Use routers with VPN support and set up a small VPN. Once this is done, the
traffic will be treated as though it were all on the local network.
3. (Best solution) – Use router s with connection tracking. This is quite easy;
VOIP also uses RTSP and faces the same challenges. If a router is marketed as having “VOIP Support”, it will have the necessary connection tracking capability to allow any type of RTSP communication (not just VOIP).
With proper planning and the correct equipment, RTSP cameras CAN stream over the WAN to a recording device for minimal additional cost and labor.
Please contact AvertX support if you require any additional information on these topics.
22
VIEWER SOFTWARE
To access the setup menu, you need to install the viewer software on your PC or recorder. The viewer software will install automatically the first time you connect to the camera. If your internet browser doesn’t install the viewer software, check the security settings or ActiveX controls and plug-in settings. If your internet browser asks for permission to install the ActiveX control, you must allow the ActiveX control to continue the installation.
The first time you connect to a camera, the browser will ask for permission to install the ActiveX Control necessary to display the camera video. Right-click the information bar and click Install ActiveX Control to allow the installation.
Note IP camera audio is only available on the Indoor IP mini dome camera. The Talk
button will not be available on the Outdoor version of the camera.
Viewer Tabs
Live – Monitor video and perform other video related functions. Setup – Set the camera name, IP address, and define users. This tab also allows you to
configure the camera settings and view streams. Advanced – Perform advanced setup configurations, like network setup, security, alarms
and maintenance. Logout – Change user.
LIVE
Full Screen – This will display the live feed in full screen. Snapshot – Click the button, and a JPEG snapshot will automatically be saved in the
appointed place. The default locat ion is: C:\.
Note If you are using Windows Vista or 7, you will need to change the Snapshot
location. Windows UAC does not allow internet programs to write directly to C:\ for security reasons.
Record – Click Record to star recording live video. Click Record again to stop recording video. Recorded video will be saved automatically to the designated location on the local workstation. The default location is C:/. This location can be changed in File Location, in the System menu.
Note If you are using Windows Vista or 7, you will need to change the video clip
location. Windows UAC does not allow internet programs to write directly to C:\ for security reasons.
Microphone – PC Network Camera Manager Software audio to camera, enables audio through an audio out on the camera.
Live Audio – Camera to PC Network Camera Manager Software, enables audio if a microphone is equipped to the camera.
Note The Microphone and Live Audio functions are only available on enable cameras.
If the camera is not enabled for these features, an error message will display.
24
SETUP
SYSTEM SETTING
The Setup menu includes System Settings, Picture Setup, and Streaming Settings.
Note The Setup menu displays limited setup options. For a complete list of setup
options, see the Advanced section.
Camera Name
Host Name – The Host Name is used to identify
the camera on your system. If camera based Motion Detection is enabled and is set to send alarm message by Mail/FTP, the host name entered here will display in the alarm message.
Time Zone – Select your time zone. Time Format – Select your desired time format. Sync With Computer Time – Select to
synchronize the camera date and time with the connected recorder.
Sync with NTP Server – Manual allows you to define the date and time manually. Network Time Protocol (NTP) is an alternate way to synchronize your camera’s clock with a NTP server. Specify the server you wish to synchronize in the NTP Server box. Then select an Update
Interval. For more information about NTP, visit www.ntp.org.
IP Address
You can choose to use a fixed IP address or a dynamic IP address (assigned by a DHCP server or router) for the camera.
Get IP an Address Automatically (DHCP)
The camera comes preconfigured with a fixed IP address, selecting Get IP address automatically requires a router or DHCP server to assign an IP address to the camera.
Note Every network device has a unique Media Access Control (MAC) address that
can be used for identification. T he MAC address is located on the bottom of each camera, and on the box label (AvertX Network Camera Manager also displays the MAC address for identification). Record your camera’s MAC address for identification in the future.
Use Static IP Address
To set up a new static IP address:
1. Select the Use static IP address option.
2. Type a new IP address in the IP address box.
3. Type a new address in the Default Gateway box.
4. Click Apply to confirm the ne w setting.
When using static IP address to log in to the IP Camera, you can access it either through AvertX IP Finder software or type the IP address directly in the address bar of your Internet Explorer.
• IP Address – The IP Address is necessary for network identification.
• Subnet mask – Used to determine if the destination is in the same subnet. The
default value is 255.255.255.0.
• Default gateway – Used to forward frames to destinations on different subnets
or for internet access.
• Primary DNS – The primary domain name server that translates hostnames into
IP addresses.
• Secondary DNS – A secondary domain name server that backups the primary
DNS.
• Web Server port – Defines the port that Internet Explorer uses to connect over
the web and view video. If this port is changed then the new port m ust be defined when attempting to web connect (ex: if your camera’s IP address is
192.168.0.100 and you change the web port to 8001, then you must type http://192.168.0.100:8001 in your browser).
• RTSP port – The default RTSP port is 554; setting range: 1024 ~65535.
• MJPEG over HTTP port – The default HTTP Port is 8008; setting range: 1024
~65535.
• HTTPS port – The default HTTPS Port is 443; setting range: 1024 ~65535.
Note No port number can be used in duplication on more than one item.
26
IPv6 Address Configuration
To enable IPv6 select Enable IPv6 and click Save. See your network administrator if you are unsure of your network configuration.
User Setup
Admin Password
Manage the password for the Administrator account.
To change the administrator password:
1. Type a new Administrator Password, and then type again to confirm the
password.
2. Click Save.
Add User
The user name and passwords are limited to 16 characters with no spaces permitted. There is a maximum of twenty user accounts.
1. Type the new User name and Password.
2. Select I/O Access, Camera Control, Talk, and/or Listen as permissions for the
User.
I/O Access – All functions in the Setup and Advanced menus are available to the User. Camera Control– Allows the User to change camera controls in the Setup menu. Talk – Allow the user to speak through the camera microphone. Listen – Allow the user to listen to audio captured by the camera.
3. Click Add.
Delete User
1. Select the user name on the User Name list.
2. Click Delete to remove the user.
3. Click OK in the confirmation window.
There is a momentary wait time while the Network Camera Manager saves parameters. When this period is complete, the User will be deleted.
Modify User
1. Select the user name on the User Name list.
2. Click Edit.
3. In the resulting window, modify the Password and/or feature permissions.
4. Click Save.
Note For security reasons, every time the user properties are opened the access
check boxes are automatically cleared. Make sure you select any user access options each time you edit the user pr oper ties.
File Location
This is the destination location that snapshot photos and recorded videos will be saved to.
To select a destination location:
1. Click Select.
2. Choose a location or folder.
3. Click Save in the file window, and then click Save again.
28
PICTURE SETTING
Picture Setup
Camera Tab
Use the Camera Tab section to modify picture settings for the camera. The sample image will change as you modify the picture settings.
Note These settings can drastically affect the camera image. AvertX suggests that
these settings are only modified by a CCTV professional, or at the instruction or a technical support representative.
Exposure
Min Shutter Speed – Choos e a pre-determined shutter speed.
Manual Mode – Changing the shutter mode to manual will allow you to select the minimum shutter speed that the camera will use. This can drastically change the amount of light entering the camera.
Click Set to save your changes.
White Balance
Use the white balance setting to change color representation in difficult lighting conditions.
Auto – White balance works within its color temperature range and calculates the best-fit
white balance. ATW – Auto-tracing white balance, the camera removes the signals within a range of
2000K to 10000K, which helps to even out the bright white portions of an image.
One Push – Balances color temperature based on a white object within the viewing area. Manual – Change the white balance value by specifying the R grain and B grain.
Click Set to save your changes.
Picture Adjustment
Each of the Picture Adjustment settings is set to the recommended default.
Brightness – Adjust the image’s brigh tness on the camera. The Backlight value is adjustable from 0 (dim) ~ +20 (brightest).
Sharpness – Increasing the sharpness level can make the image looked sharper; it especially enhances an object’s edge. The value of sharpness is adjustable from 0 ~ +10 (sharpest).
Contrast– Adjust the contrast value from -6 to 19. Saturation– Adjust the color saturation for m -6 to 19 (most saturation). Hue– Adjust the hue from -12 to 13. Backlight– Backlight compensation can correct for overly-bright backlit sceneries. D-WDR Function– Turn the Digital Wide Dynamic Range Off, or adjust between 1 and 3.
Click Set after making changes to the Picture Adjustment settings to save the settings and update the Live screen.
Motion Detecti on
Use the Motion Detection menu to configure the motion detection window(s). Here, Motion Detection can be turned On or Off, and other general settings can be specified.
To enable motion detection:
1. Use the Motion Detection dropdown to
select a motion detection preset (1-4). If choosing an additional preset after 1, check the On checkbox.
Note A motion detection preset can be turned
Off at a later time.
2. If desired, check the By Schedule check
box and use the dropdown menu to select a schedule.
3. Designate the Motion Detection Setting
values.
4. Check the appropriate boxes to designate
the Trigger Action.
5. Click Save.
30
Add Detection Window
1. Use the Motion Detection dropdown to select a motion detection preset.
2. Click Add.
Note The selected motion detection square will be red.
3. Arrange and size the motion detection window as desired.
4. Click Save.
Delete Motion Detection Window
1. Click to select the desired motion detection window.
2. Click Delete.
Motion Window
The motion window displays a red line and a dynamic blue line. The red line represents the Detection Level. The blue line w ill also be present if motion is present in the camera frame. The blue line will react accordingly based on the motion in the camera frame.
Stream Settings
Video Resolution
The camera provides eight codec options under video resolution (two single streaming options, two sets of dual streaming options, two sets of tri­streaming options, and two sets of quad-streaming options):
• H.264 Only
• MJPEG Only
• H.264 + H.264
• H.264 + MJPEG
• H.264 + H.264 + H.264
• H.264 + H.264 + MJPEG
• H.264 + H.264 + H.264 + H.264
• H.264 + H.264 + H.264 + MJPEG
Once a codec option is selected, multiple resolutions are available for each stream.
Note Due to resource management, some resolutions may be unavailable when
selecting a dual stream option.
32
Video Orientation
Normal Video – The video will be oriented as the camera position dictates. 180 Degree Rotate – Rotate the video 180 degrees. 90 Degree Clockwise – Rotate the video 90 degrees clockwise. 90 Degree Counter Clockwise– Rotate the video 90 degrees counter clockwise. Mirror Video – Flip the video across the vertical axis. Mirror + 180 Degree Rotate – Flip the video across the vertical axis and rotate 180
degrees.
GOP Size
The Group of Pictures settings allow you to modify the frame structure of the video stream. This setting changes the frequency of the I-frames that occur within the stream of P-frames (2~64). Increasing this number increases the number of P-frames between each I-frame; decreasing the file size of the stream, but increasing the risk of video decoding errors. Decreasing this number decreases the number of P-Frames between each I-frame; increasing the file size of the stream, but decreasing the risk of video decoding errors. AvertX recommends setting the GOP to be approximately twice the frame rate (e.g.: if the frame rate is 10 IPS, then set the GOP to 20).
H.264 Profile
The H.264 Profile may need to be changed if you are using a third party recorder that is not capable of decoding H.264 Main Profile video compression. Select compatible compression type for each stream if nece ssary.
Video Frame Rate
Setting the camera to transmit fewer frames can save bandwidth. Use the Frame Rate Control screen to adjust the frame rate of each stream.
Each of the MJPEG and H.264 streams can have a separate frame rate setting from 1 to 30 frames per second.
Note Higher frame rate will increase video
smoothness, as well as file size and bandwidth usage.
Note Lower frame rate will decrease video
smoothness, as well as file size and bandwidth usage.
Video Compression
You can select an MJPEG / H.264 compression mode on the video compression page appropriate for your application. You can also select to display compression inflation on the Live Screen.
MJPEG compression settings include:
• High compression, low bitrate, low quality
• Middle compression, default
• Low compression, high bitrate, high quality
H.264 compression settings include:
• 1024kbps, highest compression, lowest quality
• 2048kbps
• 4096kbps, middle compressi o n, default
• 6144kbps
• 8192kbps, low compression, highest quality
CBR Mode Setting
• The Constant Bit Rate mode allows you to lock in the bit rate of the H.264
stream. If this setting is not enabled, bit rate may fluctuate based on available bandwidth.
34
ADVANCED
SYSTEM SETTING
Network Setup
The Network Setup settings will automatically be set at the recommended default after the camera connection is made.
DDNS
DDNS (Dynamic Domain Name Service) is a service that allows a connection to an IP address using a hostname (URL) address instead of a numeric IP address. Most Internet Service Providers use Dynamic IP Addressing that frequently changes the public IP address of your internet conne ctio n; this mea ns that when co nnec t ing to the camera over the internet, you need to know if your IP address has changed. DDNS automatically redirects traffic to your current IP address when using the hostname address.
• Enable DDNS – Select the check box to enable DDNS.
• Provider – Select a DDNS host from the Provider list .
• Host name – Type the registered domain name in the field.
• Username/E-mail – Type the username or e-mail required by
the DDNS provider for authentication.
• Password/Key – Type the password or key required by the DDNS provider for authentication.
Network Advanced
QoS
Quality of Service allows you to prioritize network traffic services of the camera’s functions. The QoS function utilizes the Differentiated Services prioritized using Codepoint vales (DSCP).
Note Routers and switches on the network must be QoS or DSCP capable, and have
these settings enable for this function to operate on your network.
SNMP Settings
With Simple Network Management Protocol (SNMP) enabled, the camera can be monitored and managed remotely with a network management system. Contact your network administrator if you are not familiar with SNMP setup.
UPnP (Universal Plug N’ Play)
• Enable UPnP – When enabled, the camera will appear in My Network Places on Windows computers running UPnP on the same network.
• Enable UPnP Port Forwarding – When enabled, the camer a w ill attempt to open the web server port on the router automatically.
• Friendly Name – Set a name to easily identify the camera.
Network Security
HTTP
The camera can send alarm messages to a specific Hypertext Transfer Protocol (HTTP) site when motion is detected or when the sensor input is activated. You can assign alarm messages to up to two HTTP sites.
IP Filtering
IP Filtering allows you limit access to your IP cameras by IP address. You can “Allow” or “Deny” a specific IP address by adding it to the appropriate list. IP addresses on the “Allowed IP List” will be able to access the IP camera. IP addresses on the “Deny IP List” will NOT be able to access the IP camera.
IEEE 802.1XSEAP-TLS
This is a well supported security protocol commonly used by wireless vendors. This security method requires a valid CA certification and key. When properly configured, all communication between the client (usually a recorder) and the camera is encrypted.
36
Alarm Application
The alarms menu is where alarm connections are configured.
Alarm Switch – Designate when the alarm will be active; Off, On, or By Schedule.
Alarm Type – Designate if the alarm is normally open or normally closed.
• NOH – NO stands for Normally Open.
• NC/L – NC stands for Normally Closed.
Example: A door sticker consists of two contacts that are connected when under normal conditions. This type of input would be a NC/L or normally closed alarm. The alarm will trigger when the two contacts are no longer connected, such as an abnormal condition when the door is opened.
Alarm Output – Choose high or low. Trigger Action – Specify which actions the camera should take when motion is detected.
• Send Alarm Message by FTP / E-mail – Select to send an alarm message to a configured FTP and/or e-mail address when moti on is dete ct ed. When sending to email, the alarm notification is text only. When sending to FRP, the alarm notification will upload a text file to the FRP location.
• Upload Images by FTP – Select to assign an FTP site and configure various parameters as shown in the figure below. When motion is detected, event images will be uploaded to the appointed FRP site.
• Upload Image by E-mail – Select to assign an e-mail address and configure various parameters as shown in the figure below. When motion is detected, event images will be sent to the appropriate e-mail addres s.
Note Make sure SMTP or FTP configuration has been completed. See the Mail and
FTP sections for more information.
• File Name – Enter a file name in the box, ex. Image.jpg. The uploaded image’s file name format can be set in this section. Select the one that meets your requirements.
Consult the documentation to the sensor input device to determine which of these to use.
Tampering and Network Failure Detection
Tampering Alarm – Turn the Tampering Alarm On, Off, or On By Schedule. Tampering Duration – Designate the amount of time (in seconds) that tampering must
occur in order for a Tampering Alarm to activate. Triggered Action – Designate the actions that will occur upon a Tampering Alarm
activating. Network Failure Detection – Turn the Network Failure Detection On, Off, or On By
Schedule.
Detection Type – Designate the IP Address that will be tested and how often (in minutes). Triggered Action – Designate the actions that will occur upon Network Failure Detection
activation.
38
Mail, HTTP and FTP Setup
The camera can send an e-mail via Simple Mail Transfer Protocol (SMTP) when a variety of events occur. SMTP is a protocol for sending e-mail mess ages betw een serv ers. SMTP is a relatively simple, text-based protocol, where one or more recipients of a message are specified and the message text is transferred. The configuration page is shown as follows:
Two sets of SMTP accounts can be configured. Each set includes SMTP Server, Account Name, Password and E-mail Address settings. For SMTP server, contact your network service provider for more specific information.
SD Card
All AvertX IP cameras include an integra ted mi croSD ™ card slot that can be used to record video or images. The card slot is compatible with a microSD™ card up to 16GB.
Load Device Information – Displays the storage total size and free space information of the included microSD™ card.
Current Recording Partition – Amount of space designated for recording on the microSD card.
Format – Allows you to format the microSD card. Eject – Safely eject the microSD card. Recording List – Display s a list of files saved to the card. You can delete files from the
card, or save them to your local PC.
Note If you are using Windows Vista, 7, or 8, you will need to change the Snapshot
location. Windows UAC does not allow internet programs to write directly to C:\ for security reasons.
Network Share
Network Share is a network protocol that runs a variety of different system platforms, allowing for file sharing between computers operating on Windows and computers operating on Unix. This serves as an additional storage type.
Configuration requires the host IP address, share name, and credentials. Once configured, cameras can record events to the network share.
Note Network Share can be hosted on a Windows, Mac, or Linux system.
40
Recording Schedule
The recording schedule allows you to set up scheduled recording to the microSD™ card or to Network Sharing.
Recording
This section allows you to define recording schedules for the camera.
For continuous recording:
1. Select type of Recording Storage.
• microSD card™: save recorded data to the microSD™ card located in the camera.
• Network Share: save recorded data to the designated Network Share location.
2. Select Always as the type of Recording Schedule.
3. Click Save.
To set up scheduled recording:
1. Select type of Recording Storage.
2. Select Only during time frame as the type of Recording Schedule.
3. Use the appropriate check box to designate a day of the week.
4. Type a Start Time and Duration.
5. Click Save.
6. Repeat steps 3-5 for each desired day of the week until the desired schedule is completed.
Note Start Time and Duration are measured in 24-hour format (HH:MM).
To delete a recording schedule:
1. Select Disable for the type of Recording Schedule.
—OR—
Click on the desired weekday schedul e and then cli ck Delete.
Schedule
This section allows you to establish schedules to use in other section.
To create a schedule:
1. Select a Schedule set (1-10).
2. Check the desired week day check boxes.
3. Select Day or Night.
4. Designate a Start Time and Duration.
5. Click Save.
Interval Recording
42
Maintenance
On the Maintenance page you can export the cameras current configuration, or import the configuration for a camera. Use the factory default page to reset the IP Camera to factory default settings if necessary.
Note Do not import configuration files from different models of cameras.
Configuration
Export Configuration:
1. Check the appropriate boxes for information that you want exported.
2. Click Export Configurations.
3. The .bin file will be saved.
Note The default location for exported configurations is C:\
Upload (Import) Configuration:
1. Click Browse in the Configuration Import box.
2. Select a .bin file that you want to import.
3. Click Import.
4. Click Yes when prompted that the import will cause a system reboot.
Factory Default
There are two factory default settings available: Full Restore that restores default settings including network settings, and a Partial Restore that restores default settings excluding network settings. A system reboot is also available; this preserves all settings.
Note If a Full Factory Default is used, you will need to use the Network Camera
Manger to find the desired camera(s) again.
Software
Note Make sure the software upgrade file is available before starting the software
upgrade.
1. Click Browse and find the upgrade file.
Note Do not change the file name, or the system will fail to find the file.
2. Select the file name from the list under Step 2.
3. Click Upgrade. The system will check to find the upgrade file, and then start to upload the upgrade file. The upgrade status bar will display on the page. When it reaches 100%, the viewer will return to Home page.
4. Close the internet browser.
5. Go to the Windows Control Panel and double-click Add or Remove Programs. Locate the Camera Viewer software on the Currently installed programs list and click Remove to uninstall the previous software version.
6. Open the internet browser again and log in to the camera. The system will automatically download the new version of the Camera Viewer software.
PICTURE SETTING
Video Mask
You can use the video mask page to define a privacy mask to keep users from viewing parts of the image. You can enable up to five privacy masks and choose a color to obscure the live view form users.
Hot Spot
The Spot feature allows you to transmit different parts of the camera image on separate streams. Each stream is displaying a portion of the image at the full size of a regular image. This is useful for focusing on details in different areas of a single camera view.
Text Overlay
Text Overlay allows you to select text to be displayed over the video. Three options are available: Date, Time, and a Custom String (up to 20 alphanumeric characters).
44
STREAMING SETTING
Audio
Audio Input Grain – sets the amplification that the camera applies to the incoming audio before transmitting.
Audio Output Delay – Sets a delay in the audio transmission. This is used when there is
significant lag in video transmission to help sync the audio and video.
Volume – Sets the audio output volume level (for listening to live audio). Network Transfer – Sets the camera to continue transmitting audio even if the video
stops.
LOGOUT
The Logout tab allows you to switch between users.
1. Click Logout.
2. If prompted to close the browser window, click Yes.
3. Using the Network Camera Manager Software, select the camera you wish to view in the Viewer Software.
4. Click Browse.
5. Login as the appropriate user.
SPECIFICATIONS CAMERA SPECIFICATIONS
Model
HD6012-RW
Maximum Resolution
1080p (2MP)
Image Sensor
Sony 1/2.8” CMOS
Video Compression
H.264 / MPEG4 / MJPEG
Frame Rate
30 IPS @ 1080P [1920 x 1080 / 2MP]
30 IPS @ 1280 x 1024 (1.3MP)
30 IPS @ 720P [1280 x 720 / 1MP]
30 IPS @ D1 [720 x 480]
30 IPS @ CIF [352 x 240]
ONVIF
Profile S
Streaming
Up to 2 simultaneous streams
Browse Support
Internet Explorer (Active X)
Day / Night
True Day/Night (IR Cut Filter)
Wide Dynamic Range
True WDR
Lens
4 mm
Horizontal Field of View
86º
Iris
F2.0 Fixed
Minimum Illumination @ 50IRE
Color: 4.0 Lux @ F1.6
B/W: 0.8 Lux @ F1.6
0 Lux w/IR LED ON
Minimum Illumination @ 30IRE
Color: 2.4 Lux @ F1.6
B/W: 0.5 Lux @ F1.6
0 Lux w/IR LED ON
White Balance
Auto, Manual, Preset
Auto White Balance Range
2000~11000K
46
Model
HD6012-RW
Backlight Compensation
Yes
Auto Gain Control
Yes
IP Rating
N/A (Indoor)
Operating Temperature
14°F (-10°C) ~ 122°F (50°C)
Active / Passing Cooling
Active (Fan)
Power Consumption
5W Max
Rated Amperage
0.41A (12vDC)
Input Voltage
PoE / 12vDC
PoE Class
0
IR Range
Up to 30 ft (9 m)
IR LED
15 IR LED
Audio In/Out
1 / 1
Alarm In/Out
1 / 1
microSD Card Slot
microSD / microSDHC 32GB max
Weight
0.5 lb (221 g)
Dimensions
(W x H) 3.56" x 4.5" (90.4 mm x 114.5 mm)
Housing / Dome Cover
White / Clear
Tilt / Rotation
Tilt = 50º Rotation - 360º
32910AC
www.AvertX.com 1-855-228-3789
© 2016 AvertX
All rights reserved. No part of this publication may be reproduced by any means without written permission from AvertX. The information in this publication is believed to be accurate in all respects. However, AvertX cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new editions to this publication may be issued to incorporate such changes.
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use