avertX HD40IR Quick Start Manual

This guide is a quick reference for users to install and operate HD40IR Night Vision
HD Indoor/Outdoor Bullet Cameras. It provides only basic information regarding
installation and operation of your camera. For further details, please refer to the

HD40IR User Manual.

Before proceeding, please check to conrm that the box contains the items listed

here. If any item is missing or has defects, DO NOT install or operate the product and
contact AvertX for assistance.

About this Guide

CONTENTS

HD40IR Bullet Camera Desiccant Envelope

Quick Start Guide & Installation CD

HD40IR QUICK START GUIDE

Screws

Anchors

The HD40IR camera can be installed directly
onto a wall or ceiling. Be sure that the
structure is strong enough to support the
camera.

1. Remove the HD40IR camera from the
packaging.

2. Connect the Ethernet cable from the
ceiling or wall to the dongle on the
camera.

3. Afx the camera base to the ceiling
or wall with the included self-tapping
screws.

4. Use a Phillips-head screwdriver to loosen
the set screw on the side of the camera
bracket mount.

5. Adjust the position of your camera.

6. Tighten the set screw to secure your
camera.

Note The HD40IR camera is equipped with

a seal inside the housing to prevent
moisture from entering. If you have
concerns about moisture entering
through the wall via the cable, AvertX
recommends sealing the opening at the
wall and the base of the camera with
silicone caulking.

INSTALLATION

Align Holes on Wall

Adjust Aim

32334AA

MICRO SD CARD
AND RESET BUTTON

Copyright © 2013 AvertX. All rights reserved. Information contained in this document
is subject to change without prior notice. AvertX does its best to provide accurate
information, but cannot be held responsible for typos or mistakes.

32334AA

• If passing the cord through a wall or ceiling, drill a 3/4”” hole.

• For outdoor installations, ensure the connection between your network cable and

the camera jack is housed within a wall or indoors.

• For outdoor installations, use silicone caulking to seal any holes in the wall or
ceiling to protect against leaks.

NETWORK CABLE INSTALLATION

When installing your AvertX Night Vision HD Indoor/Outdoor Bullet Camera, it is im­portant to consider how the network cable attached to the camera is arranged.

1-855-2avertX (1-855-228-3789)

www.avertx.com

If you are using this camera with an AvertX recorder, follow the instructions in the
recorder user manual to connect to your camera. You can also set up your camera
using your PC. Use your browser to go to 192.168.0.250. The viewer software will

automatically be installed on your PC the rst time you connect to the camera. If your

internet browser doesn’t install the viewer software, check the security settings or
ActiveX controls and plug-in settings. If your internet browser asks for permission to
install the ActiveX control, you must allow the ActiveX control to continue.

To enable installation of ActiveX controls on Internet Explorer:

1. From the Tools menu, click Internet Options.

2. Click Security,and then click Internet.

3. Click Custom Level and ensure that all ActiveX controls and plug-ins are set
to Enable or Prompt.

To add the camera to your trusted sites:

1. From the Tools menu, click Internet Options.

2. Click Security, and then click Trusted Sites.

3. Click Sites.

4. Type the IP Address of the camera. Ensure that the Require server verication

check box is cleared.

The username and password are case sensitive. AvertX strongly recommends
changing the password after the initial setup to prevent unauthorized access to the
camera.

Username – admin

Password – 1234

CONNECTING TO THE CAMERA

USERNAME AND PASSWORD

For more information on installing your AvertX camera, see the user manual or view

instructional videos at avertx.com/videos.

For Further Instruction

Remove Cover

Micro SD and Reset Button

Your HD40IR camera is equipped with a slot for a Micro SD card and a Reset button.

To access these, you must rst remove the cover of the HD40IR camera.

Insert a Micro SD card to be used for emergency video backup if desired. Push the
reset button to return the camera to factory default settings, if necessary.

Reset button

Micro SD

card slot