Avertx HD300IR User Manual

NIGHT VISION HD
INDOOR/OUTDOOR
HD300IR QUICK START GUIDE
About this Guide
This guide is a quick reference that offers users basic information regarding
installation and operation of the HD300IR Indoor / Outdoor High Denition IP
Cameras. For further details on installation and operation, please refer to the User Manual on the included CD and at avertx.com.
Before proceeding, please conrm that the box contains the items listed here. If any
item is missing or has defects, DO NOT install or operate the product and contact AvertX for assistance.
HD300IR
Dome Camera
Paintable
Dome Cover
Torx Tool
Screws Anchors
Paintable Dome Cover
The dome cover for the HD300IR is paintable, allowing for a
customizable look. Use a paint designed for plastic and paint away from the camera dome to avoid overspray.
Paint
Documents &
Installation CD
IP DO
INSTALLATION
Remove Dome Cover
Align Holes on Wall
ME CA
The camera can be installed directly onto a
wall or the ceiling. Be sure that the structure is strong enough to support the camera.
1. Remove the camera dome cover.
2. Use the included mounting template to pre-drill holes for the mounting screws and, if passing the cable through the ceiling or wall, drill a 3/4” hole.
3. Connect the Ethernet cable to the dongle on the camera.
Protect the network cable connection
from water damage by running the
cord inside a wall or ceiling, or through conduit.
For outdoor installations, seal any
holes in the wall or ceiling with silicone caulk to protect against water intrusion.
4. Afx the base of the camera to the wall with the included self-tapping screws and wall anchors.
5. Adjust the position of your camera.
6. Replace the dome cover.
MERA
1 2 3
Adjust Aim
32862AB
MICRO SD CARD
microSD card slot
NETWORK CABLE INSTALLATION
& RESET BUTTON
Your camera includes a microSD card slot (up to 16GB), which can be used for emergency video
backup. The microSD card is not included.
You can return the camera to factory default
settings if necessary. Press the Reset button for
30 seconds.
You must remove the cover of the camera to access the microSD card slot and the Reset button.
For optimal image quality, you may need to manually focus your AvertX camera after
it has been installed.
1. Remove the dome from the camera.
2. Remove the rubber gasket surrounding the lense.
3. Twist the textured ring at the base of the lens
to focus your camera.
4. Replace the rubber gasket.
5. Replace the dome on the camera.
Reset button
When installing your AvertX Night Vision HD Indoor/Outdoor Dome Camera, it is
important to consider how the network cable attached to the camera is arranged.
Protect the network cable connection from water damage by running the cord inside a wall or ceiling, or through conduit.
If passing the cord through a wall or ceiling, drill a 3/4” hole.
For outdoor installations, seal any holes in the wall or ceiling with silicone caulk to protect against water intrusion.
CONNECTING TO THE CAMERAFOCUSING THE CAMERA
If you are using this camera with an AvertX recorder, follow the instructions in the HDIP recorder user manual to connect to your camera. You can also set up your camera over your network using an internet browser. Type the IP address of the camera in the address bar of your internet browser to connect to the camera.
If your internet browser doesn’t install the camera viewer software, check the security settings or ActiveX controls and plug-in settings. If your internet browser asks for permission to install the ActiveX control, you must allow the ActiveX control to
continue the installation.
Default IP address:
192.168.0.250
Remove
gasket
Copyright © 2014 AvertX. All rights reserved. Information contained in this document
is subject to change without prior notice. AvertX does its best to provide accurate
information, but cannot be held responsible for typos or mistakes.
Turn ring
to focus
User Name and Password:
The username and password are case sensitive.
Username – admin
Password – 1234
1-855-2avertX (1-855-228-3789)
www.avertx.com
32862AB
Loading...