AVerMedia AVerTV6.2 Service Manual

AVerTV 6.2

DISCLAIMER

User Manual English

All the screen shots in this documentation are only example images. The images may vary depending on the pro duct and software version.
Information presented in this documentation has been carefully checked for reliability; however, no responsibility is assumed for inaccuracies.
The information contained in this documentation is subject to change without notice.

COPYRIGHT

© 2007 by AVerMedia TECHNOLOGIES, Inc. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored
in a retrieval system, or translated into any language in any form by any means without the written permission of AVerMedia TECHNOLOGIES,
Inc.

AP-6.2

200704

Table of Contents

Chapter 1 Device Introduction ......................................................................................1

Chapter 2 AVerTV 6 Introduction..................................................................................2

Chapter 3 Introducing the AVerTV Application ...........................................................3

3.1 Launching the AVerTV 6 Application................................................................................................................3

3.2 Running the AVerTV 6 application for the first time ......................................................................................... 3

3.3 Introducing the User Interface ............................................................................................................................6

3.4 The Control Panel............................................................................................................................................... 7

3.5 Remote Control................................................................................................................................................... 9

3.5.1 Remote Control Buttons (Model 1) ............................................................................................................9

3.5.2 Remote Control Buttons (Model 2) ..........................................................................................................10

3.5.3 Remote Control Buttons (Model 3) ..........................................................................................................12

3.6 Resizing the TV Monitor Window ................................................................................................................... 13

3.7 Always on Top.................................................................................................................................................. 13

3.8 Setting Windows® Power Options.................................................................................................................... 13

3.9 Minimize the Application ................................................................................................................................. 15

3.10 Change Definitions of the Remote Control Buttons ......................................................................................... 15

3.11 Customize the Remote Control Source Button ................................................................................................. 16

3.12 Changing the OSD Attributes ........................................................................................................................... 17

Chapter 4 TV .................................................................................................................19

4.1 Analog TV ........................................................................................................................................................ 19

4.1.1 Scanning Channels.................................................................................................................................... 19

4.1.2 Scanning Channels (For Advanced Users) ...............................................................................................20

4.1.3 Customize Video record settings ..............................................................................................................21

4.1.4 Fine Tuning Color of the Display ............................................................................................................. 24

4.1.5 Enhancing the Video Quality.................................................................................................................... 25

4.1.6 Using the De-interlace Function ............................................................................................................... 25

4.2 Digital TV......................................................................................................................................................... 26

4.2.1 Scanning Channels.................................................................................................................................... 26

4.2.2 Scanning Channels (For Advanced Users) ...............................................................................................27

4.2.3 Customize Video record settings ..............................................................................................................28

4.2.4 Using the EPG Function ...........................................................................................................................29

4.2.5 Fine Tuning Color of the Display ............................................................................................................. 30

i

4.2.6 Enabling Subtitle Function ....................................................................................................................... 31

4.3 Adding and Deleting Program Lists .................................................................................................................32

4.4 Selecting a TV/Radio Channel.......................................................................................................................... 33

4.5 Creating Channel Groups..................................................................................................................................33

4.6 Adjusting Volume............................................................................................................................................. 34

4.7 Specifying a Channel Name or Description...................................................................................................... 35

4.8 Modifying a program list name......................................................................................................................... 35

4.9 Removing Unwanted Channels.........................................................................................................................36

4.10 Using the OverScan Function ........................................................................................................................... 38

4.11 16-Channel Preview.......................................................................................................................................... 39

4.12 Changing Signal Source.................................................................................................................................... 39

4.13 Sound Controlling (Optional) ........................................................................................................................... 40

Chapter 5 FM Radio ......................................................................................................41

5.1 FM Radio Controls ...........................................................................................................................................41

5.2 How to Auto Scan FM Radio Channels............................................................................................................ 41

5.3 Manually Scanning Specific FM Channels....................................................................................................... 42

5.4 Selecting a Channel ..........................................................................................................................................42

5.5 Adjusting Volume............................................................................................................................................. 43

5.6 Skipping Unwanted Channels........................................................................................................................... 43

5.7 Adding a Radio Frequency ............................................................................................................................... 44

5.8 Modifying a Radio Name ................................................................................................................................. 44

5.9 Adding and Deleting Program Lists .................................................................................................................44

5.10 Creating Channel Groups..................................................................................................................................45

5.11 Customizing Audio Recording Settings............................................................................................................ 45

5.12 Sound Controlling (Optional) ........................................................................................................................... 46

5.13 Viewing RDS Information (Optional) .............................................................................................................. 47

Chapter 6 TimeShift...................................................................................................... 48

6.1 TimeShift Controls ...........................................................................................................................................48

6.2 Customizing TimeShift Settings ....................................................................................................................... 48

6.3 Using the TimeShift Function........................................................................................................................... 50

Chapter 7 DVR ..............................................................................................................51

7.1 DVR Controls ................................................................................................................................................... 51

7.2 Recording Settings............................................................................................................................................ 51

7.3 Using the Recording Function ..........................................................................................................................52

ii

7.4 Playing the Recorded Programs........................................................................................................................ 52

7.5 Picture-in-Picture Display................................................................................................................................. 53

Chapter 8 Image Capture.............................................................................................54

8.1 Before Capturing ..............................................................................................................................................54

8.2 Capturing a TV/ Video Image........................................................................................................................... 54

8.3 Multiple Image Sequence Capture.................................................................................................................... 56

Chapter 9 Teletext (PAL/SECAM only)........................................................................57

9.1 Customize the Display Mode............................................................................................................................ 57

9.2 Overview .......................................................................................................................................................... 58

9.3 Toolbar Buttons ................................................................................................................................................ 59

9.4 LED Lamp ........................................................................................................................................................ 59

9.5 Using Teletext................................................................................................................................................... 59

Chapter 10 Scheduler..................................................................................................62

10.1 Adding Schedules ............................................................................................................................................. 62

Chapter 11 Hot Ke ys ...................................................................................................65

Chapter 12 Customer Service ....................................................................................67

iii

Chapter 1 Device Introduction

Thanks for purchasing AVerMedia’s product. The table below lists an overview of the product you
purchased. From this table, you can quickly learn about your product features and know which chapter
you need to read. Please do read this table before using AVerTV 6 application.

Product Name AVerTV MCE 116 Plus
Model No. M116
TV System  Digital TV ( DVB-T  ATSC  DVB-S)

; Analog TV (; NTSC ; PAL ; SECAM)

Audio Mode ; Stereo ; Mono ; SAP
FM Radio ; Support  Not Support
Remote Control ; Support ( Model 1 ; Model 2)

 Not Support

External Signal
Source

Others ; Teletext  MHEG-5

Reference Chapter ; Chapter 1

; S-Video ; Composite

 EPG ; iEPG

; Closed Caption  Digital Subtitle

; Chapter 2
; Chapter 3 (;3.1-3.4 ;3.5.2 ;3.6-3.12)
; Chapter 4 (;4.1 ;4.4-4.13)
; Chapter 5
; Chapter 6
; Chapter 7
; Chapter 8
; Chapter 9 (;9.2)
; Chapter 10
; Chapter 11
; Chapter 12

Note

1

Chapter 2 AVerTV 6 Introduction

Now, with this product, you can watch TV, listen to the radio, record your favorite programs and

enjoy other features on your PC. Turn your computer system into a real multimedia entertainment
center.

You’ll never miss your favorite ball games, soaps or game shows anymore because the TimeShift
function performs background recording of a TV program. This means you can return and watch from
the part of the program where you left off.

To enjoy high quality TV or radio programs, AVerMedia

Please be noted that the functions or the remote control mentioned in this manual may vary depending
on the product you purchase and the area you live.

®

product is your best choice.

2

Chapter 3 Introducing the AVerTV Application

r

The AVerTV 6 application allows you to watch TV or video, and record still or motion video

on your PC while you work on your computer.

3.1 Launching the AVerTV 6 Application

Run the AVerTV 6 application from the Programs menu.

To run the application, click

then click AVerTV 6
the desktop. Or, you can double-click the AVer

corner of the screen.

Note: AVerQuick launcher is important for both of the remote control and the Scheduler.

If it is not activated, the remote control feature is automatically disabled and the

Scheduler will not perform any preset schedules.

. Another way is to double-click the AVerTV 6 program icon “ ”on

Start, point to Programs, choose AVerMedia, AVerTV 6, and

Quick TV Launche

Quick launcher located at the lower right

3.2 Running the AVerTV 6 application for the first time

If this is your first time running the application, the Setup dialog box will appear to prompt
you to scan for channels. (For details, please refer to the section Scanning Channels).

1. Choose your desired signal input (Digital TV, Analog TV or FM Radio) on the left pane

of the Setup dialog box.

Note: Before choosing the signal input, please make sure that your country/region is

correct. For more information, please refer to “Scanning Channels” in Chapter 3.

3

2. Then you need to select the TV option to search for air channels, or select CATV to scan

for cable channels if your choice is “Analog TV” in step 1.

3. Click New and the Program Li st dialog box will appear. Type in the desirable name and

click OK.

4. Click Program Scan to search for available channels/programs in your area.

5. After scanning, the active TV channels will be listed inside the box. Click Apply to save

the scanned channels.

Note: Digital channels that are in red text indicate they are locked channels (eg. Adult channels).

6. To exit the current dialog box, click OK.

4 5

7. If you choose FM Radio or Digital TV in step 1, just repeat step 3-6 to complete the

program scanning.

3.3 Introducing the User Interface

The TV monitor allows you to watch live TV or video.

1 Panel On / Off 8 Channel Up/Down
2 Playback Seek Slider 9 Resize Window
3 Play / Pause 10 Show / Hide Video Frame
4 Stop 11 Minimize
5 TimeShift 12 Full Screen
6 Record 13 Exit
7 Volume

The Control Panel provides button controls for selecting channels, adjusting volume,

capturing images, and more. It has a panel display that shows the current channel number and
channel name.

To display or hide the

the TV Monitor.

Control Panel, click the button located at the lower left corner of

6

3.4 The Control Panel

(This picture is only for reference)

The table below describes the functions of the buttons on the Control Panel.

BUTTON FUNCTION

Signal Status /

1

Repeat Play Status

TV/Radio mode: Right click on the info area of the control panel
to switch signal sources.

Playback mode: Right click on the info area of the control panel

The system will continuously

Signal Strength

2

Backward

3

Channel Loop

4

16-Channel Preview

5

and enable the Repeat function.

playback the files in the playlist.

Display signal strength.

Move backward in intervals.

Return to previously accessed channel.

Display 16 consecutive TV channels on the TV Monitor
window.

Channel Up/ Down

6

Mute

7

Setup

8

Move up/down the channel list

Turn off the sound.

Allows you to:

*Autoscan channels.
*Create channel groups.
*Configure snapshot settings.

*Customize record settings.
*Customize the TimeShift function.

9

Teletext

View Teletext (PAL/SECAM) / Closed Caption (NTSC)
information.

10

11
12
13

EPG

Snapshot

Forward

Always on Top

View EPG information (This function is only available for
digital TV).

Capture a single image or a sequence of images.

Skip forward in intervals.

Make the TV monitor float over the top of other program
windows.

7 8

14

Full Screen

Show TV/Video programs in full screen.

Program List

15

Audio Mode

16

Scheduler

17

Play List

18

Show/ Hide Numeric Panel

19

Radio Source

20

Change Video Source

21

Record

22

TimeShift / Pause

23

Next File

24

Previous File

25

Stop

26

Play / Pause

27

Volume Control

28

Display the program list and adjust color, volume and so on.

Switch between available audio modes.

Display Scheduler dialog box.

Create a playlist of video files to playback.

Toggle between displaying or hiding the Numeric Panel.

Switch between FM radio and DVB-T radio. (Only access to
DVB-T Radio Broadcast, not Digital Audio Broadcast system.)

Switch between analog TV, digital TV, or S-video.

Record the current TV show.

Performs background recording of the live TV program. This
function lets you view the recorded parts, while at the same time,
recording is in progress. / Freeze the playback temporarily.

Play the next file in the playlist.

Play the previous file in the playlist.

Stop the playback, recording, TimeShift, etc.

Playback recorded video files. / Freeze the playback temporarily.

Increase/decrease the volume level.

Help

29

Numeric Buttons

30

View User’s Manual.

Select channels/programs.

3.5 Remote Control

You can use remote control to turn on/off the programs, select channels, adjust volume and so
on. Please be noted that you have activated Quick TV.

3.5.1 Remote Control Buttons (Model 1)

6

7

1
2

3

4

5

Button Description

1. Power Turn on/off the application

2. VOL +/- Volume up/down.

3. Source Switch between available signal sources.

4. Numeric Buttons Select a TV channel.

5. MUTE Turn on/off the sound.

6. CH ▲/▼ Go up or down to the next active channel.

7. CH RTN Go to the previously selected channel.

9

3.5.2 Remote Control Buttons (Model 2)

Button Description

1. POWER Turn on/off the application.

2. NUMERIC BUTTONS - Select a TV channel.

- Under the 16-Channel Preview mode, use ← ↑ → ↓ to

highlight the intended channel.

3. CH RTN Go to the previously selected channel.

4. 16-CH PREV 16-Channel Preview.

5. VOL▲/▼ Volume up/down.

6. FULL SCREEN Display TV in full screen.

7. AUDIO Switch between available audio modes.

8. ► (Play) Play the last recorded or played file.

9. ■ (Stop) - End the playback or recording.

- End the TimeShift mode and return to real-time TV or Radio

mode.

10. (Forward) - Advance the playback.

- Jump to the Teletext page of the corresponding color

according to this button.

11. SLEEP - Go to the next file in the playlist.

- Set the time to put your computer in Stand By or Hibernate

mode.

- Jump to the Teletext page of the corresponding color

according to this button.

12. MENU

13. EPG

14. WAKE UP

15. TELETEXT

Display or hide the Control Panel.

Launch the Electronic Programme Guide.

- Go to the previous file in the playlist.

- Set the time to bring your computer out of Stand By or

Hibernate mode.

- Jump to the Teletext page of the corresponding color

according to this button.

View Teletext (PAL/SECAM) / Closed Caption (NTSC)
information

10

16. TIMESHIFT /PAUSE

17. (Rewind)

18. ● (Record)

19. MUTE

20. CH ▲/▼

21. SNAPSHOT

22. DISPLAY

23. SOURCE

- Freeze the playback.

- Switch from real-time TV or Radio to TimeShift mode.

- Rewind the playback.

- Jump to the Teletext page of the corresponding color

according to this button.

Switch to DVR mode and record the current program or video
into your hard drive.

Turn on/off the sound.

Go up or down to the next active channel.

Capture the on-screen image to a bitmap file.

Display information.

Switch between available signal source.

11

3.5.3 Remote Control Buttons (Model 3)

Button Description

1.Power Turn on/off the application

2.Numeric Buttons

3.CH RTN Go to the previously selected channel.

4.16-CH PREV 16-channel preview.

5. VOL▲/▼ Increase/decrease the volume.

6.FULL SCREEN Display TV or video in full screen.

7. AUDIO Switch between available audio modes.

8. ► (Play) Play the last recorded or played file.

9. ■ (Stop)

10. (Forward)

11. (Next File)

12. AUTOSCAN

13. (Previous
File)

14. TELETEXT View Teletext information.

15.
TIMESHIFT/PAUSE

16. (Rewind)

17. ● (Record) Switch to DVR mode and record the current program or video into your hard drive.

18. MUTE Turn on/off the sound.

19. CH ▲/▼ Go up or down to the next active channel.

20. SNAPSHOT Capture the on-screen image to a bitmap file.

21. DISPLAY Display information.

22. TV/FM

- Select a TV channel.

- Under the 16-channel preview mode, use↑↓← → to highlight the intended

channel.

- End the playback or recording.

- End the TimeShift mode and return to real-time TV or FM mode.

- Advance the playback.

- Jump to the Teletext page of the corresponding color according to this button.

- Go to the next file in the playlist.

- Set the time to put your computer in Standby or Hibernate mode.

- Jump to the Teletext page of the corresponding color according to this button.

Display or hide the Control Panel.

- Go to the previous file in the playlist.

- Set the time to bring your computer out of Standby or Hibernate mode.

- Jump to the Teletext page of the corresponding color according to this button.

- Freeze the playback.

- Switch from real-time TV or FM to Time Shift mode.

- Rewind the playback.

- Jump to the Teletext page of the corresponding color according to this button.

Switch between available signal sources.

12

3.6 Resizing the TV Monitor Window

To enlarge or reduce the size of the TV Monitor window, click and drag the lower right
corner of the window.

Double-click the TV Monitor window to display it in full screen or click the Full Screen

button

When in full screen mode, just double-click anywhere on the screen to revert to the normal
TV window size.

on the Control Panel.

3.7 Always on Top

To make the TV monitor window float over the top of
other program windows, right-click on the TV monitor.
In the pop-up menu, point to Video and choose Always
on Top.

OR,

Click the Always on Top button

Panel.

3.8 Setting Windows

This option allows you to put your computer in Stand By or Hibernate mode, power off, exit
the application or log off from the computer while you are away from the computer.

Note:

Stand By: Stand By is a state in which your monitor and hard disks turn off, so that your
computer uses less power.

Hibernate: Hibernation is a state in which your computer shuts down to save power but first
saves everything in memory on your hard disk.

Please do the following:

1. First, Click the Setup button

the left pane.

2. By default, the system is set to enable the Stand By/Hibernation option. What you have to

do is to choose the desired power-saving settings. If your computer has a problem with

coming out of Stand By or Hibernate mode, please clear the Stand By/Hibernate option.

®

Power Options

on the Control

and in the Setup dialog box, click Miscellaneous icon on

13

3. Then press the Sleep button on the remote control repeatedly to set the execution time.

OR,

1. Right-click on the TV monitor, point to Sleep and select the desired mode.

2. Right-click on the TV monitor again, point to Sleep and choose an execution time.

3. The time setting will be displayed on the TV monitor. For details, please see the

description below.

Time setting mode Description
Sleep 30/60/90/120 Minute(s) Your computer will go into Stand By or Hibernate mode in

30/60/90/120 minutes.

Now Your computer will go into Stand By or Hibernate mode in

about 10 seconds.

Cancel Your computer will return to original settings.

14 15

Note: The system will detect if your VGA card supports DXVA. If yes, enable the “DXVA

Support” to activate the video acceleration of the VGA card. To watch HDTV, it is strongly
recommended to execute “DXVA Support”.

3.9 Minimize the Application

To minimize AVerTV application to the system tray (notification area), click the Setup

button

the Minimize to Tray check box. Or clear the check box to simply minimize the application

to a taskbar button.

and in the Setup dialog box, click Miscellaneous icon on the left pane. Then Select

3.10 Change Definitions of the Remote Control Buttons

1. Click the Setup button and in the Setup dialog box, click on the Remote Remapping icon on

the left pane.

2. To re-define a function for a certain button:

● Select a desired button and choose a new command from the right pane of the dialog box.

Then click Assign.

● From the right pane of the dialog box, drag the desired command and drop it on the remote
button which you want to change the definition.

3. Click Apply to save the settings.

4. Click Clear All to delete all definitions of the remote control or click Default to revert to the

factory setting.

3.11 Customize the Remote Control Source Button

On the Remote Source Control page, you may customize the remote control “Source” button to switch
on the selected item.

1. Click the Setup button

Remote Source Control icon on the left pane.

2. Select the signal source that you want.

3. Click the

location you desire.

4. Click Apply to save the settings. Or click Default to revert to the factory setting.

UP or DOWN button at the right side until the selected signal reaches the

and in the Setup dialog box, click on the Remote Remapping→

16

3.12 Changing the OSD Attributes

Click the Setup button and in the Setup dialog box, click the Personalise icon on the left

pane. On this page, you can customize the curtain effect, LCD speed or change the appearance
of the TV monitor and the control panel (Skins).

Click the Setup button and in the Setup dialog box, click the Personlise → OSD icon on

the left pane. On this page, you can determine the OSD information, display duration and

adjust OSD color. Then, click Apply to save the settings.

17

18

Chapter 4 TV

In this chapter, we will introduce methods to scan programs, select a TV/Radio program,
create a group and so on.

4.1 Analog TV

4.1.1 Scanning Channels

If you didn’t complete the channel scanning when you first ran the application, please follow
these steps to complete this procedure.

1. Click the Setup button and in the Setup dialog box, select an available Avermedia device in

the left pane.

Note:

Make sure that your Country/Region is correct.
a. First, select an available Avermedia device in the left pane.
b. From the Region/Country drop-down list, select your country or region.

c. Click Apply to save the settings.

2. Then select Analog TV. On this page, choose the TV option to search only for air channel

or select CATV to scan for cable channels.

3. Click New and the Program List dialog box will appear. Type in the desirable name and

click OK.

4. Then Click Program Scan to start the scanning process.

19

The application comes with a default frequency table therefore the application will use
this table to search for active channels/programs. If you want to terminate the searching

process, just click Stop.

5. You can check the scanning progress from the progress bar. After scanning, the active

TV/Radio channels will be listed inside the box. Click Apply to save the scanned channels.

4.1.2 Scanning Channels (For Advanced Users)

1. Click Advance located at right-lower corner in the Program Information section. Then

the Advance Program Configuration dialog box will appear.

2. If you don’t want to miss any channels, click All Frequencies Scan.

20

3. When a warning message appears, click Yes to continue the procedure or click No to abort

this operation.

4. After scanning, new active channels/programs will be memorized and listed in the left

pane of the dialog box.

5. Click Apply to save the scanned channels.

Note: Here you can modify the channel name, select the video and audio system. If you

want to revert to factory setting, simply click Default button.

4.1.3 Customize Video record settings

To customize the video record settings, please do the following.

1. Click the

the left pane.

2. Select the Record Format option.

3. Determine the video file format to use for saving the recorded video file.

4. You can use the default format or select New to create your own file format.

Setup button and in the Setup dialog box, click on the Analog TV icon on

21

5. Click New and the Format dialog box appears. In the Format dialog box, select the file

format you want and enter the desired name in the text box. Click Next.

6. In the Video dialog box, you can set the video format and audio format. Click Finish.

22

7. If you want to change the settings of your own file format, click Modify. Or click

Delete to remove the unwanted file format that you created.

8. Click Apply to save the setting and click OK to exit the current dialog box. To abort

this operation, click Cancel.

Note: To determine the length of recording and to choose a destination folder in which

to save the recorded audio, please refer to the section titled Record Settings in Chapter 6.

Information:
File Format Description
MPEG-1 Choose MPEG-1 format for video files that are intended for CD-ROM

playback on a computer or for Internet transmission. MPEG-1 allows file
compression and offers VHS quality picture. Just about every system
available today can play MPEG-1 and does not need special software or
hardware.

MPEG-2 Videos compressed using MPEG-2 have extremely high quality pictures

and full CD-quality sound. Choose MPEG-2 format for video files that are
intended for DVD-ROM playback on a computer or if you want broadcast
quality videos.

VCD When you choose this format, the recorded video file will be saved in

MPEG-1 format that is compliant with VCD standards. Standard VCD
frame size and frame rate are 352 x 240 pixels at 29.97 fps for NTSC and
352 x 288 pixels at 25 fps for PAL.

SVCD When you choose this format, the recorded video file will be saved in

MPEG-2 format that is compliant with SVCD standards. Standard SVCD
frame size and frame rate are 480 x 480 pixels at 29.97 fps for NTSC and
480 x 576 at 25 fps for PAL.

DVD When you choose this format, the recorded video file will be saved in

MPEG-2 format that is compliant with DVD standards. Standard DVD
frame size and frame rate are 720 x 480 pixels at 29.97 fps for NTSC and
720 x 576 at 25 fps for PAL.

AVI AVI is the most common video file format for playback on the computer.

It can be saved in uncompressed form if you want high quality video, or
compressed using any of the available codecs if you want to minimize the
file size.

WAV A common audio file format for Windows computers. It was created by

Microsoft and has become a standard PC audio file format.

iPod

A video format base on H.264 standard but has smaller video bit rate. It’s an iPod ­compatible format.

MP4-H.264

WMA

Videos compressed using MPEG-4 standard are two or three times more efficient
than MPEG-2.

networks

applications.

An audio file format that is use for content intended for local playback or
download and play. It provides near-CD quality.

This format can be applied to a wide variety of applications or

and systems like HD-DVD, Digital TV, Broadcast and Streaming

23

WMV

MP3

WMV stands for Window Media Video, which is defined by Microsoft. This file
targets audiences with high speed Internet or LAN connections.

An audio format compressed with a standard defined by Motion Picture Experts
Group offers near-CD quality sound.

4.1.4 Fine Tuning Color of the Display

If the color or picture quality of the TV display needs to be adjusted, please do the following.

1. Right click on the TV monitor. When a pop-up menu appears, select Individual

Channel Setting. Or click Program List button
Individual Channel Setting button

.

2. When a dialog box appears, select Display tab.

on the control panel and then click

3. Then use

, or the slider to adjust Brightness, Contrast, Hue, Saturation and

Sharpness until you get an accurate color.

4. If your device supports the 713x chip, you can choose color adjustment tab. Try the

provided options to get desired color.

5. If you just want to adjust color of one specific channel, select Individual Channel

Setting and repeat step 3. To apply the converted settings to all channels, click Apply
All button

6. Click Default button

.

if you want to revert to the factory settings.

24

4.1.5 Enhancing the Video Quality

This function can reduce noise. Choose an appropriate option
listed below.

z Video Quality Enhancement Enable: Activate to improve the

video quality.

z Video Quality Enhancement Disable: Disable the video

quality enhancement function.

z Video Quality Enhancement Automatic: Automatically adjust

video quality depending on the video screen size.

OR,

1. Right click on the TV monitor. When a pop-up menu appears, select Individual Channel

Setting. Or click Program List button
Channel Setting button

.

2. When a dialog box appears, select Video/Audio Settings tab.

3. Choose a desired option from the Video Quality Enhancement drop-down list.

4. If you just want to enhance video quality of one specific channel, select Individual Channel

Setting and repeat step 3. To apply the converted settings to all channels, click Apply All
button

5. Click Default button

.

if you want to revert the factory settings.

4.1.6 Using the De-interlace Function

on the control panel and then click Individual

The de-interlace function can remove the jagged edges of images in serial rapid movement. It is
recommended using this function to ensure smooth and clear video images.

1. Right click on the TV monitor. When a pop-up menu appears, select Individual Channel

Setting. Or click Program List button
Channel Setting button

.

on the control panel and then click Individual

2. When a dialog box appears, select Video/Audio Settings tab.

25

3. From the De-Interlace drop down list, try all the options to compare which can give you the

best quality.

4.2 Digital TV

4.2.1 Scanning Channels

If you didn’t complete the channel scanning when you first ran the application, please follow
these steps to complete this procedure.

1. Click the Setup button

device in the left pane

Note:

Make sure that your Country/Region is correct.
a. First, select an available AVerMedia device in the left pane.
b. From the Region/Country drop-down list, select your country or region.

c. Click Apply to save the settings.

.

and in the Setup dialog box, select an available Avermedia

2. Then select Digital TV.

3. Click New and the Program List dialog box will appear. Type in the desirable name and

click OK.

26

4. Then Click Program Scan to start the scanning process.

The application comes with a default frequency table therefore the application will use
this table to search for active channels/programs. If you want to terminate the searching

process, just click Stop.

5. You can check the scanning progress from the progress bar. After scanning, the active

TV/Radio channels will be listed inside the box. Click Apply to save the scanned channels.

Note: Digital Channels that are in red text indicate they are locked channels (eg. Adult channels).

4.2.2 Scanning Channels (For Advanced Users)

1. Click Advance located at right-lower corner in the Program Information section. Then

the Advance Program Configuration dialog box will appear.

27

2. When there are channels missing from the channel memory, select All Frequencies or

Single Frequency.

Note: All Frequencies Scanning may take you a while. Please be patient.

3. Once you select Single Frequency, you need to specify the correct Frequency, for

example 533000 (KHz), and Bandwidth.

4. Then click Scan.

5. After scanning, new active channels/programs will be memorized and listed

in the left pane of the dialog box.

6. Click Apply to save the scanned channels.

4.2.3 Customize Video record settings

To customize the video record settings, please do the following.

1. Click the

the left pane.

2. Select the Record Format option.

3. Select recording type.

format. Or you can choose Audio Only for sound recording.

Setup button and in the Setup dialog box, click on the Digital TV icon on

You can use the default format or select New to create your own file

28

4. Click Apply to save the setting and click OK to exit the current dialog box. To abort

this operation, click Cancel.

Note: To determine the length of recording and to choose a destination folder in which

to save the recorded audio, please refer to the section titled Record Settings in Chapter 6.

4.2.4 Using the EPG Function

Electronic Program Guide (EPG) is a service that allows you to check the next succeeding
program schedule and even the program schedules of the whole week. If the EPG service is

provided in your region/country, simply click the

First, select the desired program from the Program drop-down list and the EPG window will

display the schedule for one week. Surely, you can also see the related information such as
program name, time, and description about the program on the right pane of the window.

In addition, when switching channels, the TV screen can show the current and succeeding
program information.

EPG button to open the EPG window.

Our EPG window also allows you to preset a schedule for watching or recording programs.

Just select your favorite programs and click Record button

Application button

If you want to download the latest program schedule, please click the Update button . Click to

sort the EPG list by time or by channel.

. And the system will execute your command on schedule.

29 30

or the Active TV

Note: To use EPG function, please make sure that the EPG GMT settings is correct.

a. Click on the control panel to see the Setup window.
b. Click Digital TV on the left pane and press Advance located at right-lower corner.

c. In the Advance Program Configuration window, click the desired channel.
d. In the EPG GMT settings section, select Using customized EPG time to adjust the EPG

time according to local time. Or, select Using standard EPG time to adjust the EPG time

according to Greenwich Mean Time.

4.2.5 Fine Tuning Color of the Display

If the color or picture quality of the TV display needs to be adjusted, please do the following.

1. Right click on the TV monitor. When a pop-up menu appears, select Individual

Channel Setting. Or click Program List button
Individual Channel Setting button

.

2. When a dialog box appears, select Display tab.

3. Then use

, or the slider to adjust Brightness, Contrast, Hue, Saturation and

Sharpness until you get an accurate color.

4. If you just want to adjust color of one specific channel, select Individual Channel

Setting and repeat step 3. To apply the converted settings to all channels, click Apply
All button

.

on the control panel and then click

5. Click Default button if you want to revert to the factory settings.

4.2.6 Enabling Subtitle Function

If your local broadcasters provide subtitle service, you can view those text by doing the followings:

Right click the TV screen, point to Subtitle and choose the desired language.

To hide the subtitle, please right click the TV screen, point to Subtitle and choose Close.

31

4.3 Adding and Deleting Program Lists

Selecting a program list allows you to switch between the channels of the selected program
list only when pressing the
program list, do the following:

To add a new program list:

1. Click the

TV icon on the left pane.

2. Click New and the Program List dialog box will then

appear (as shown at right).

3. Type in a program list name and click OK.

4. Click Program Scan and click Yes to continue the

scanning process.

Setup button and in the Setup dialog box, click the Analog TV or Digital

Channel Up/Down button. If you want to add or delete a

5. Available channels will then be listed in the

delete the unwanted programs by clearing the check box.

6. Click Apply to save the setting and click OK to exit the current dialog box. Or you can

click Cancel to revert to the original settings.

OR,

If you don’t want to scan programs every time creating a new program list, you can use

Copy function.

1. From the program drop-down list, select the program list that you

want to duplicate.

2. Click Copy and the Program List dialog box will appear.

3. Type in desired name and click OK.

Program Information and now you can

4. Finally, just like the steps described above, clear the check mark next to the

unwanted channels.

To delete a program list:

1. Click the

TV icon on the left pane.

2. From the program drop-down list, select the name of the group that

you want to remove.

3. Click Delete to remove the selected program list.

Setup button and in the Setup dialog box, click the Analog TV or Digital

32

4.4 Selecting a TV/Radio Channel

There are three ways of switching between TV/Radio channels:

OR,

◆Click the Channel Up/Down buttons (

the Control Panel) repeatedly until reaching your desired channel.

◆Click

the Numeric buttons to get your desired channel number.

◆Click the Program Li st button

select the Display Mode button
drop-down list and then double-click on the desired channel.

to open the Numeric Panel (as shown at right). Then click on

. When the Program Panel appears,

. Choose the desired program list from the

on the TV monitor window or on

Note: Locked channels (eg. Adult channel) are in red text.

4.5 Creating Channel Groups

To add a new channel group:

1. Click the Program List button

2. Click the Setup button

.

on the control panel.

33

3. When a dialog box appears, click New button .

4. Specify the desired name in the text box.

5.

Hold down Shift or Ctrl key and click the channels from the list to select your own channel line up,

then click
to the desired group.

6.

Click Save to save the settings or click Cancel to abort without saving. If you want to

delete the unwanted group, simply click Delete

to add your selection to the desired group. Or drag the selected channels and drop them

4.6 Adjusting Volume

On the Control Panel, click and drag your mouse over the Vol ume meter to
increase or decrease the volume level. You can also press the + / – keys on the

numeric keypad to adjust the volume.

OR,

1. Right click on the TV monitor. When a pop-up menu appears, select Individual

Channel Setting. Or click Program List button
click Individual Channel Setting button

2. When a dialog box appears, select Video/Audio Settings tab.

3. Use

and next to the icon to adjust the system volume or the device volume.

on the control panel and then

.

34

4. If you just want to adjust individual volume level, select Individual Channel Setting

and repeat step 4 to increase or decrease volume.

5. To apply the converted settings to all channels, click Apply All button

6. Click Default button

if you want to revert the factory settings.

4.7 Specifying a Channel Name or Description

To assign a channel name or specify a description:

1. Click the

Digital TV icon on the left pane.

2. Under the

name or description.

3. Type in the channel name or description, then press Enter.

OR,

1. Click the

TV icon on the left pane.

2. Click Advance located at right-lower corner in the Program Information section. Then

the Advance Program Configuration dialog box will appear.

Setup button and in the Setup dialog box, click the Analog TV or

Name column, double-click the text box of the channel you want to assign a

Setup button and in the Setup dialog box, click the Analog TV or Digital

.

3. In the dialog box, select the channel/program you want to assign a name or description.

4. In the Name text box, type in the desired name or description. Press Apply to save the

settings and click OK to exit the dialog box. Or you can press Cancel to abort without

saving.

4.8 Modifying a program list name

You can change a program list name easily. To rename a program list, follow the steps
described below:

35

1. Click the Setup button and in the Setup dialog box, click Analog TV or Digital TV

icon on the left pane.

2. Click Advance located at right-lower corner in the Program Information section. Then

the Advance Program Configuration dialog box will appear.

3. Type the desired name in the Program List Name text box.

4. Press Apply to save the setting and click OK to exit the dialog box. Or press Cancel to

abort the saving.

4.9 Removing Unwanted Channels

If you want to exclude unwanted channels from your channel list, do the following:

1. Click the

TV icon on the left pane.

2. Click Advance located at the right-lower corner in the Program Information section.

Then the Advance Program Configuration dialog box will appear.

Setup button and in the Setup dialog box, click the Analog TV or Digital

36

3. In the Program Information section, select the unwanted channel and then click Delete.

This channel will be removed and that means you won’t be able to access these
programs anymore.

OR,

If you just want to skip a certain channel, do the following:

1. First, select the unwanted channel in the Progra m Information section.

2. Clear the Enable check box so that you will not access that channel

when you press Channel Up/Down buttons.

3. However, you can still see the channel in your program list. If you want to watch that

channel again some day just select the Enable check box.

37

4.10 Using the OverScan Function

On some broadcast channels, you might see
distorted lines or black spaces on the top, sides,
or bottom of the screen. These video artifacts
derive from the source signal, and can be masked

using the OverScan feature.

To hide the edges of the picture:

z Right-click on the TV Monitor and choose

OverScan to enable it.

OR,

1. Right click on the TV monitor. When a

pop-up menu appears, select Individual Channel Setting. Or click Program List

button

2. When a dialog box appears, select Video/Audio Settings tab.

3. Specify an appropriate number (0~50) in the Overscan text box to get a better quality

image.

4. If you just want to apply OverScan setting to one specific channel, select Individual

Channel Setting and repeat step 4.

5. To apply the converted settings to all channels, click App ly All button

6. Click Default button

You can see the difference from the pictures below:

on the control panel and then click Individual Channel Setting button .

.

if you want to revert the factory settings.

Before using OverScan function After using OverScan function

38

4.11 16-Channel Preview

The 16-channel preview function can
can see clearly which TV p

To v

pre iew the channels:

1. Click

2. Click the 16-Channel Preview button.

3. The screen will be gradually filled up with 16 TV channels

starting from the currently selected channel.

Select a channel and press the numeric button “5” on the

4.

remote control to view it only and freeze the other channels. If you want to continue

to display other channels just press C letter on the keyboard.

5. ls

To display a channel on the TV Monitor window, select any one of the 16 channe
on-screen and double-click on that channel, or use the arrow ↑, ↓, ←, → button of
your keyboard and then press

6. Or, click the right mouse butto

channel.

4.1

2 Changing Signal Source

There are two ways to change signal source:

to open the Numeric Panel.

rograms are currently showing on these channels.

display 16 TV channels on-screen at the same time. You

,

Enter. You will then be tuned in to that channel.

n or press ESC to return to the originally selected TV

switch between TV and radio / external video sign

․ To als, click the Radio Source button

or Video Source button

․ Right click on the left pane of the control panel and a pop-up menu appears. Choose the

desired signal source.

on the control panel.

39

4.13 Sound Controlling (Optional)

This function provides a variety of sound effects.

1. Right click on the TV monitor. When a pop-up menu appears, select Individual

Channel Setting. Or click Program List button
Individual Channel Setting button

2. When a dialog box appears, select Sound mixer tab.

3. Choose the desired sound effects from the drop-down list.

4. Then use

5. If you just want to adjust sound effects of one specific channel, select Individual

Channel Setting and repeat step 4 and step 5.

6. To apply the converted settings to all channels, click App ly All button

7. Click Default button if you want to revert the factory settings.

, or the slider to control the “Stereo”, “Bass” and “Treble” level.

.

on the control panel and then click

.

40

Chapter 5 FM Radio

5.1 FM Radio Controls

Click the FM Radio button to listen to your favorite radio station programs.

Use the following button controls for selecting FM radio channels, adjusting volume,
scanning FM channels, recording radio programs and more.

To change back to live TV, click the Radio Source button.

(This picture is only for reference)

1.

2.

3.

4.

5.

6.

7.

8.

9.

10.

11.

12.

13.

Signal Status / Enable or disable Repeat Play
Signal Strength
Backward
Channel Loop
16-Channel Preview
Channel Up/Down
Mute
Setup
TEXT/RDS(It may vary depends on your

device and your living area.)
Forward
Radio Source
Program List
Audio Mode

14.

15.

16.

17.

18.

19.

20.

21.

22.

23.

24.

25.

26.

Schedule

Play List
Show/Hide Numeric Panel
Video Source
Record
TimeShift / Pause
Next File
Previous File
Stop

Play / Pause
Volume Control
Help
Numeric Buttons

5.2 How to Auto Scan FM Radio Channels

If this is your first time to use FM radio, perform auto scan to search and memorize active FM
radio stations in your area.

To auto scan FM radio stations:

1. Click the Setup button

and in the Setup dialog box, select an available AVerMedia

device in the left pane. Then select FM Radio.

41

2. Click New and the Program List dialog box will appear. Type in the desirable name and

click OK.

Note: The system will assign a default name (FM-Radio) if you don’t create a new program

list before scanning.

3. Click Scan. All active channels will be automatically scanned and memorized.

4. To terminate the scanning, click Stop.

5. Click Apply to save the setting and click OK to exit the current dialog box. To abort the

setting, click Cancel.

5.3 Manually Scanning Specific FM Channels

Instead of scanning all channels, you can choose to manually scan one or a few channels only.
To do this, follow these procedures.

To manually rescan specific FM radio channels:

1. Click the Setup button

pane.

2. Enter the channel frequency that you want to start scanning in the text box.

3. Select 0.01 MHz, 0.05MHz or 0.1MHz as your tuning increment.

4. Click

The scanning will stop when the application finds the closest ACTIVE FM frequency.

5. Or click

6. Click the Modify button if you’d like to keep the newly scanned frequency.

to scan upward or to scan downward from the selected channel frequency.

or to increase/decrease the frequency to search your preferred channel.

and in the Setup dialog box, click FM Radio icon on the left

5.4 Selecting a Channel

To select a channel:

1. Click

‧ Click on the

‧ Click the Channel Up/Down button repeatedly until reaching your desired channel.

OR,

2. Use the

to open the Numeric Panel.

numeric keys on your keyboard to select a channel.

Numeric buttons to select a channel.

42

5.5 Adjusting Volume

On the Control Panel, click and drag your mouse over the Vol ume meter to
increase or decrease the volume level. You can also press the + / – keys on the

numeric keypad to adjust the volume.

OR,

1. Right click on the TV monitor. When a pop-up menu appears, select Individual

Channel Setting. Or click Program List button
Individual Channel Setting button

2. When a dialog box appears, select Video/Audio Settings tab.

3. Use

4. If you just want to adjust individual volume level, select Individual Cnannel Setting

5. To apply the converted settings to all channels, click App ly All button

6. Click Default button

and next to the icon to adjust the system volume or the device volume.

and repeat step4 to increase or decrease volume.

if you want to revert the factory settings.

.

on the control panel and then click

.

5.6 Skipping Unwanted Channels

If you want to exclude undesirable channels from your FM channel list, do the following:

1. Click the Setup button

pane.

2. In the Program column, click the unwanted channel. The check mark will be removed,

indicating that the channel will be excluded from your channel list and that you won’t

be able to access and hear them through the Channel Up/Down button.

and in the Setup dialog box, click FM Radio icon on the left

43

5.7 Adding a Radio Frequency

If the desired channel cannot be found through scanning, follow the instructions below.

1. Click the Setup button

dialog box, click FM Radio icon on the left

pane.

2. Specify the correct frequency in the text box

(as shown at right) and click Save.

and in the Setup

5.8 Modifying a Radio Name

You can manually modify any exiting FM radio channel.

1. Click the Setup button

pane.

2. Double click on

3. Enter the name or description you want in the provided text box and then press Enter.

4. To modify more channels, repeat step 2 to 3.

Name column of the existing FM channel which you want to modify.

and in the Setup dialog box, click FM Radio icon on the left

5. Click Apply to save the setting and click OK to exit the current dialog box.

5.9 Adding and Deleting Program Lists

Selecting a program list allows you to switch between the channels of the selected program
list only when pressing the
channel group, do the following:

To add a new program list:

1. Click the Setup button

left pane.

2. Click New and the Program List dialog box appears. Type in a program name and

click OK.

Channel Up/Down button. If you want to add or delete an FM

and in the Setup dialog box, click FM Radio icon on the

44

3. Now you can start to scan FM radio channels and manage the scanned FM data for this

new program list. For more information, refer to How to Auto Scan FM Radio
Channels.

4. To add more program lists, repeat steps 2 to 3.

To delete a program list:

1. Click the Setup button

and in the Setup dialog box, click FM Radio icon on the

left pane.

2. From the drop-down list, select the name of the program list that you want to remove.

3. Click Delete to remove the selected program list.

5.10 Creating Channel Groups

To add a new channel group:

1. Click the Program List button

2. Click the Setup button

.

3. When a dialog box appears, click New button

on the control panel.

.

4. Specify the desired name in the text box.

Hold down Shift or Ctrl key and click the channels from the list to select your own channel line up.

5.

Then, click
them to the desired group.

to add your selection to the desired group. Or drag the selected channels and drop

6.

Click Save to save the settings or click Cancel to abort without saving. If you want to

delete the unwanted group, simply click Delete

5.11 Customizing Audio Recording Settings

To customize audio recording settings:

1. Click the Setup button

pane.

2. Then select Record Format. You can choose default format as your audio file format.

Or, you can click New to create your own file format. For file format description,
please refer to the section titled Customize Video Record Settings in chapter 3.1.

and in the Setup dialog box, click FM Radio icon on the left

45

3. In the Format dialog box, select the audio file format.

4. Enter the desired format name or description in the Format Name text box.

5. Click Next. In the Video dialog box, select the desired audio format.

6. Click Finish.

7. If you want to change the setting of your own file format, click Modify or you can

click Delete to remove the unwanted file format that you created earlier.

8. Click Apply to save the setting and click OK to exit the current dialog box. To abort

this operation, click Cancel.

Note: To determine the length of recording and to choose a destination folder in which

to save the recorded audio, please refer to the section titled Recording Setting in Chapter 6.

5.12 Sound Controlling (Optional)

This function provides a variety of sound effects.

1. Right click on the TV monitor. When a pop-up menu appears, select Individual

Channel Setting. Or click Program List button
Individual Channel Setting button

on the control panel and then click

.

46

2. When a dialog box appears, select Sound mixer tab.

3. Choose the desired sound effects from the drop-down list.

4. Then use

5. If you just want to adjust sound effects of one specific channel, select Individual

Channel Setting and repeat step 4 and step 5.

, or the slider to control the “Stereo”, “Bass” and “Treble” level.

6. To apply the converted settings to all channels, click App ly All button

7. Click Default button

if you want to revert the factory settings.

.

5.13 Viewing RDS Information (Optional)

RDS (Radio Data System) is an international standard for transmitting the digital data along
with FM Radio signal. An RDS-capable radio can display name of the station, program types,

local traffic information or commercials, etc. To view RDS information, press
control panel.

on the

47

Chapter 6 TimeShift

The TimeShift function performs background recording of a TV/Radio program, and lets you
return and watch any part of the recorded program. At the same time, the live TV/Radio
program continues to be recorded and played back so you won’t miss any part of the show.
You can also advance forward to skip commercials or rewind to replay scenes one more time.

6.1 TimeShift Controls

Use the following button controls in the Control Panel to start recording a live program, play
back the program from where you left off, advance forward, rewind, and more.

BUTTON FUNCTION

Backward

1

Playback Seek

2

Volume

3

Mute

4

Setup

5

Forward

6

TimeShift / Pause

7

Stop

8

Click to move backward in intervals
Drag the slider tab to move to any part of the recorded program
Drag your mouse up/down to increase/decrease the volume level.
Turn off the sound.
Allows you to:
*Autoscan channels.
*Create channel groups.
*Configure snapshot settings.

*Customize record settings.
*Customize the TimeShift function.
Click to skip forward in intervals

Click to perform background recording of the live program and play it back
simultaneously. / Click to temporarily freeze the playback.
Click to terminate recording and return to the live program

6.2 Customizing TimeShift Settings

Before you start using the TimeShift function, first check its recording settings to see if they
fit your needs.

To check and customize settings:

1. Click the

Setup button and in the Setup dialog box, click the Storage icon on the

left pane. You will then see the following settings.

48

2. By default, TimeShift performs recording of the TV program by creating a temporary

video file and deletes this file once you click the
video file, select the

Keep TimeShift Files check box.

Stop button. If you want to save the

3. In the Record section, you can determine your filename format, recording time, file

size and destination folder.

4. Click Apply to save the new settings and click OK to exit the current dialog box. Or,

click

Cancel to use the original settings.

To customize the file quality:

1. Click the

TV / FM Radio

Setup button and in the Setup dialog box, click the Analog TV / Digital

icon on the left pane.

2. Then click Timeshift icon.

3. Here you can determine the video size, bit rate and sample rate. Please be noted the

items may vary depending on the device you use.

4. Click Default if you want to revert to the factory settings.

49

6.3 Using the TimeShift Function

To pause the live program:

1. Click the

record the program.

2. When you want to rewind, use the

you want to watch or listen again. Click and drag the slider tab to the left until you
see the part of the show you wish to watch or listen, then release the mouse button.

3. You can also click the

you reach the part where you left off.

4. To advance forward and skip some parts of the recording (for example TV

commercials), drag the slider tab to the right. You can also click the

to move forward in fixed intervals.

5. To temporarily pause the playback, click the

again to resume.

TimeShift button on the Control Panel. The application will begin to

Playback Seek slider bar to move back to the part

Backward button to move backward in fixed intervals until

Forward button

Pause button . Click Pause button

6. To return to real-time viewing of the live program, click the Stop button . This

switches off the TimeShift function and returns you to live program.

50

Chapter 7 DVR

You can use your computer as a digital video recorder, and record your favorite TV programs
or capture video from an external source to your hard drive. You can also divide the recording
files in proper sizes to facilitate burning onto removable optical media, such as CD-R and
DVD discs.

7.1 DVR Controls

Use the following button controls for recording and video playback.

BUTTON FUNCTION

1 Backward
2 Playback Seek
3 Volume
4 Mute
5 Setup

6 Forward
7 Play List
8 Record
9 Play Previous/Next File

(This picture is only for reference)

Click to move backwards in intervals

Drag the slider tab to move to any part of the recorded file.

Drag your mouse up/down to increase/decrease the volume level.

Turn off the sound.

Allows you to:

*Autoscan channels.
*Create channel groups.
*Configure snapshot settings.

*Customize record settings.

*Customize the TimeShift function.

Click to skip forward in intervals.

Click to create a playlist of video files to play back.

Click to start recording.

Click to go to the previous/next video file in the playlist.

10 Stop
11 Play /Pause

7.2 Recording Settings

Click to stop recording or playback.

Click to play back / Click to temporarily freeze the playback.

51

Before recording, check if the settings meet your needs.

1. Click the

pane.

2. By default, the system is set the recording “Date” and “Time” as the file name format.

To create your own file name format, please click Custom.

3. The Duration option allows you to specify a recording duration otherwise the system

will record the largest clip that your hard drive can accommodate.

4. This application lets you to divide the recording files into smaller parts for burning

onto removable optical media, such as CD-R (650 MB) and DVD (4096 MB) discs.

Enable the Split File Size option and select the appropriate video file size from the

drop-down list so that each video file will not exceed the limit. Or you can choose

Custom to assign the file size you want.

5. Determine the destination folder. Click

6. Click Apply to save the settings and click OK to exit the current dialog box. To abort

this operation, click Cancel.

7. To determine the file format, please refer to the section titled Customizing Video

Recording Settings in chapter 3 or Customizing Audio Recording Settings in chapter 4.

Note: To hide the sound of the TV program when recording, click the Mute button

Setup button . In the Setup dialog box, click the Storage icon on the left

to choose a folder you want.

on the Control Panel.

7.3 Using the Recording Function

To record a TV/Radio program that you want, do the following:

1. Click the Record button

2. You can click the Stop button

on the Control Panel.

to terminate the recording and return to live TV program.

7.4 Playing the Recorded Programs

Each TV program that you recorded will be saved as a video file in the assigned destination
folder.

To play back the recorded video files:

Click the

OR,

(1) Click the

(2) To add more video files to the playback list, first navigate the

Play button to play back.

Play List button , and you may see some recorded video files are listed at the

top right pane of the Playback List window.

file on the left pane to find

the folder that contains the desired video files. When you have located the folder, the
media files will then be displayed on the right top pane. Select the files that you want,
then click
list.

Insert, or click Insert All to add all media files in the folder to the playback

52

(3) To delete files from the Playback List, select them from the list in the bottom right pane

and click Delete, or click Delete all to delete all files in the playback list.

7.5 Picture-in-Picture Display

With the picture-in-picture window feature, you will be able to play
back recorded video files, and at the same time, watch live TV.

To enable PIP function, right click the TV monitor, select PIP and

choose desired position of the PIP window.

Position Description

Top-left Corner /

Top-right Corner /

Bottom-left Corner /

Bottom-right Corner /

Movable /

By default, you will be able to play back recorded video files on the main window, and at the same
time, watch live TV on the PIP window. If you want to switch the video playback to the PIP window
and the live TV to the main window, press the button
size of the PIP window and the distance between the main window and the PIP window. To exit the
PIP window, press

Display the PIP window on the top-left corner

Display the PIP window on the top- right corner

Display the PIP window on the bottom-left corner

Display the PIP window on the bottom-right corner

Resize the PIP window and separate it from the main window

. You can also press the button to fix the

.

53

Chapter 8 Image Capture

While you watch TV or a recorded video on your PC monitor, you can use the AVerTV 6 application

to capture images for your documents, presentations or web pages.

8.1 Before Capturing

Before you start capturing images, first set the destination folder for saving captured images.

Click the

choose a folder where you want to save captured images.

Setup button

and select the

,

Snapshot icon on the left pane. Then click to

8.2 Capturing a TV/ Video Image

To capture a still image, click the Snapshot button on the Control Panel. The Album

will then appear, displaying thumbnails of the captured images.

BUTTON

1 Wallpaper
2 Save as
3 Remove
4 Remove All

To capture another image, click the

thumbnails will be added to the Album as you capture more images.

By double-clicking on the thumbnails, you can view images in a full-screen window with
default image viewer.

Snapshot button on the Control Panel again. New

To display the captured image as your desktop wallpaper :

1. Select the thumbnail of the desired image and then click the

2. The selected image will be displayed as your desktop wallpaper, the background of

your desktop.

To save the captured image:

1. Select the thumbnail of the image and then click the

As

dialog box will then appear.

54

Save As button . The Sa ve

Wallpaper button .

2. From the

File Format drop-down menu, select the format for saving the captured

image.

3. Choose the Color format. The options here depend on the file

format you choose.

• Choose 24-bit to capture image in 16M colors.

• Choose 8-bit to capture image in 256 colors.

4. Click

Browse to scan for folders and select a destination location for saving the

image. Then specify a f

ile name for saving the captured image.

5. Choose the image size.

• In the Size section, select the Standard option and choose a desirable image

size from the drop-down list.

55

• If you want to set your own image size, select Customize and enter the image

Width and Height. If you want to maintain relative width and height, select the
Keep Ratio option. Choose a measurement unit from the Unit drop-down list.

You can specify any image size you want. The maximum capture size can be
1600×1200.

6. Click OK to save the image. Click Cancel if you do not want to save the image.

8.3 Multiple Image Sequence Capture

To capture a continuous sequence of images, do the following:

1. Click the

Setup button . In the Setup dialog box, click the Snapshot icon on the

left pane.

2. In the

Number of Pictures box, specify the number of images you want to capture.

3. In the

Interval Time box, specify the interval between captures. For instance, if you

specify 10 seconds, an image will be captured every 10 seconds.

4. On this page, you can choose the file format and destination folder, file name format

and image resolution in advance.

5. Click Apply to save the new settings and click OK to exit the current dialog box. Or

Click Cancel if you do not want to change the settings.

6. Click the

Snapshot button on the Control Panel to start capturing.

56

Chapter 9 Teletext (PAL/SECAM only)

Teletext makes TV viewing a unique experience. It allows you to view teletext broadcasts
from your television programs to get the most updated information on TV Schedules, News,
Stock Market Prices, Concert & Theatre information and so on. Teletext information may not
be available if there is no such service provided in your region or country.

9.1 Customize the Display Mode

1. Click the Setup button and in the setup dialog box, click the Teletext icon in the left pane.

2. From the Display Mode drop-down list, choose Other Window Display to open a new Teletext

window or choose Main Window Display to overlay the Teletext window on the TV monitor.

3. Select the Transparent check box to make the Teletext window transparent.

(This picture is only for reference)

57

9.2 Overview

Click the Teletext button on the control panel to open the Teletext application as shown

below. For more information about Teletext, please see below in this chapter.

4

1
2

5

BUTTON FUNCTION

1 Menu Bar

2 Toolbar

3 Status Bar

4 Title Bar

5 Teletext

Browser

3

This contains the names of the available drop-down list option menus. To
access any of the menu items, simply click on it or hold down Alt and press
the first character of each item.

It includes buttons that gives quick access to perform certain frequently used

functions from the Menu Bar.

Status bar is located at the lower left corner of the window. It contains a short
text message or explanation of the currently selected menu command.

This is located at the top of the window. It contains the current displayed page
number or in hexadecimal page number of an active window.

Teletext information is displayed in this area. The information would be the

TV schedules, news, stock market reports, concert & theater information and
so on.

58

9.3 Toolbar Buttons

Lock Sub page

Locks the current sub page. The upcoming transmitted sub pages will be stored in the Teletext
Cache for later use.

Previous Sub page/ Next Sub page

Switches to the next or the previous sub page.

Home (Ctrl+H)

Connects to the Teletext home page which always goes to page 100, but page 100 may not be
the primary Teletext source.

Previous Page (-) / Next Page (+)

Displays the preceding or the succeeding Teletext in hexadecimal page number.

History Back / History Forward

Retrieves the previous page in the history list.

Moves a page forward in the history list. The command is usable after one or more back steps
in the history list.

TV Scale

Changes the proportion of the Teletext window to 4 by 3.

Always On Top

Makes Teletext Window float over the top of other applications.

Teletext File

Switches between the Teletext file which is opened from the previously saved file and the
most recent Teletext information.

9.4 LED Lamp

Different LED color indicates different state.

Left LED Lamp:

Gray -- The system does not receive the Teletext broadcast data.

Green -- The system is receiving the Teletext broadcast data.

Right LED Lamp:

Green -- The cache in Teletext application is running less than 90% usage.
Yellow -- The cache in Teletext application is running over 90% usage.
Red -- The cache in Teletext application is running out.

9.5 Using Teletex

The following briefly describes how to use the Teletext feature.

Teletext Page

There are two page numbers displayed on the first line of each Teletext page. The page
number on the left is the page number that you have selected or keyed in. The other one in the
middle of line is the page number of the currently displayed Teletext data.

t

59

The newly selected page number will appear on the upper left corner of the page. Sometimes,
this may take a while to retrieve the newly selected Teletext page. There will be no changes
on the page when there is no page data transmitted with the number you have selected.

A Teletext page can be selected with one of the following methods:

y Key in the hexadecimal or Teletext page number using the numeric buttons of your

keyboard or AVerMedia TV remote control.

y Press the + (positive) or – (negative) button to move to the succeeding or preceding

Teletext page.

Copying a Teletext Page

1. Simply click and drag over the text or the area that you want to copy using the mouse.

2. Choose Copy from the Edit menu (Alt+E, C) or press Ct rl+C.

3. You can then paste the contents of the Teletext page in TXT or BMP format to a

document you are working with.

Saving a Teletext Page

Some Teletext pages include a number of subpages. If the file has subpages, Teletext will also
save the existing subpages.

1. A Teletext page can be saved using one of the following ways:

● To automatically save the file using the displayed Teletext page as the filename and

the default file format, choose Save from the File menu or press Ctrl+S.

● To save the file by specifying your own filename and different file format, choose
Save As from the File menu or press Ctrl+A.

2. A save as dialog box will appear:

3. Select the file format to use for saving the Teletext page. You can save the Teletext

page in :

TXT Text file format
BMP Windows bitmap file format
TLT Teletext file format
TLX Teletext file format

60

4. Enter a filename and click OK.

Opening a Teletext Page

1. Choose Open from the File menu or press Ctrl+O.

2. From the Open dialog box, select the file containing the teletext page you want and

click Open.

Opening Another Teletext Window

To open another teletext window, choose New Window from the File menu or press Ctrl+W.

Closing the Active Teletext Window

Choose Close Window from the File menu or press Ctrl+L to close the active Teletext page

window.

61

Chapter 10 Scheduler

The Scheduler allows you to create a list of preset schedules for watching and recording

your favorite TV/Radio programs. You can set the day and time to record the TV/Radio
program and specify the length of recording.

To run this application, click the
Scheduler dialog box will appear.

1

2

The check box next to the Program column (as shown at right)

indicates the schedule will be executed at a preset time. Once the
application starts to execute a scheduled task, the system will clear the
check mark automatically. If you want to skip the schedule temporarily,
just clear the check box.

Schedule Management

Schedule button on the Control Panel. Then the

BUTTO N

1 Current Time
2 Selected Schedule

This displays a list of preset schedules you have created.

Modify

Select a preset schedule and click this button to make changes.

Delete

Click this to delete selected schedule.

Delete Expired Schedule

Click this to delete the expired schedule.

Delete All

Click this to delete all schedules.

10.1 Adding Schedules

To create a new schedule:

3. Click the

Add button .

4. The following dialog box will then appear:

62

5. Type the desired name in the Schedule Name text box.

6. From the Function drop-down list, select Activate AVerTV to watch a TV program or

listen to a radio broadcast. Otherwise, select Record to save a TV/Radio program for
future viewing/listening. You can also select Silent Record which means the system

will perform background recording instead of activating the TV/Radio program. If you

want to schedule a task to enable Timeshift function, select Timeshift.

Note: If you select Silent Record, when the application is performing the

recording task, the icon

will appear on the task bar (the lower right corner of
the screen). To immediately watch or listen to the TV/FM program which is
being recorded, just double-click this icon.

7. In the After Record-Schedule, it automatically switches to the selected power control

mode when the schedule recording is completed. Choose an appropriate power control
status listed below:

‧ Watch TV: Switch to real-time TV mode.
‧ Exit: Turn off the AVerTV Application.
‧ Stand By: Turn off your monitor and hard disks.
‧ Hibernate: Save everything and then turn off your computer.
‧ Shut Down: Turn off your computer.

Note: If you choose Watch TV from the drop-down list, after completing the Silent

Record task, the icon will appear on the task bar (the lower right corner of

the screen). Just double-click this icon, you can immediately watch live TV or
listen to the radio.

63

8. In the Program Settings section, select the desired device, video source, group and

channel you want.

9. Set the schedule to tune in live TV or to perform recording. You can set the schedule on

Once, Daily or Weekly.

‧ Choose
‧ Choose
‧ Choose

Once to perform schedule at a preset day and a preset time.
Weekly to perform schedule every week, at a preset day and time.
Everyday to perform schedule everyday at a preset time.

10. If you choose Activate AVerTV in step 4, click Insert

to complete the settings. If you choose Record or Silent
Record, you need to do the following.

11. Click the Advance icon.

12. In the Record Setting section, you can determine the

file format, recording duration, file size, destination
folder and audio mode.

13. Click

Insert to save the new schedule or click Cancel

to abort without saving.

64

Chapter 11 Hot Keys

You can use the default hot keys or create your own hot keys.

To re-define the shortcut keys:

1. Click the

2. Choose the signal status from the Category drop down list.

3. Choose a command that you want to specify a new hot keys.

4. Assign hotkey combination to the command that you use most often and then click Assign. Or you

can click Remove to delete hotkeys.

Setup button . In the Setup dialog box, click the Keyboard icon on the left pane.

(This picture is only for reference)

5. Click Default if you want to revert to the factory setting.

6. Click Apply to save settings or click Ca ncel to abort without settings.
Note: It is recommended to use an unassigned key to use as your new keys.

65 66

The following is the default definition:

Hot Key Description Function

UP/DOWN ARROW Channel or Frequency

Up/Down

L Channel Loop

Press to go to the next upper/lower
TV/Radio channel.

Press to go to the previously accessed
TV/Radio channel.

NUMERIC KEYS Select Channel

Use NUMERIC KEYS to directly enter
the TV/Radio channel number.

ESC Stop

or, Change back to Normal

View
F1 Help
F2 Minimize

F5 Full Screen
F6 Display (OSD) information
F8 16-Channel Preview

Stop (playback, recording, TimeShift, or
16-Channel Preview). Or change full
screen back to normal view.

Open the Users Manual.

Minimize the application and an icon will appear
in the notification area. To return to the previous
screen, double click the icon again.

Show TV/Video in full screen.

Display information on the TV monitor.

Press to perform 16-Channel Preview
function.

+/- (on your numeric
keypad)

Volume

Press to increase or decrease the volume
level.

LEFT/ RIGHT
ARROW

Rewind/

Fast Forward
A Audio Mode
D Show/Hide TV Monitor Panel

M Mute
Ctrl + N Play Next File
Ctrl + P Play Previous File
Ctrl + R Record
P Play / Pause

Ct r l + S Snapshot

Ctrl + T TimeShift
Insert Transparent

Page Up Previous page
Page Down Next page

Press to rewind or fast forward (for
playback and TimeShift).

Choose between available languages.

Toggles between showing and hiding the
panel on the TV monitor window.

Turn off/on the sound.

Play the next file in the playlist.

Play the previous file in the playlist.

Start recording.

Play/Pause (for playback, recording, and
TimeShift).

Capture an image (or a continuous
sequence of images).

Enable the TimeShift function.

Make Teletext window transparent. (Only
available for Teletext overlay mode.)

Go to the preceding Teletext page.

Go to the succeeding Teletext page.

Home Home page

Go the Teletext home page.

Chapter 12 Customer Service

The AVerTV application provides a convenient tool, which allows users to contact
AVerMedia’s customer service department easily via our website. Please make sure that you
have already connected to the Internet.

To contact the customer service:

1. Right-click on the TV monitor window. When a menu list

pop-up, choose About (as shown at right).

2. When a information dialog box appear, select the office in

your area from the drop-down list.

Click to connect to our website. Then click to exit the current dialog box.

3.

www.avermedia.com

67