AVERATEC AV4265-EH1, AV4270-EH1 User Manual

AVERATEC

User’s Manual

i -1

Notice

The information in this user’s manual is subject to change without notice.

THE MANUFACTURER OR RESELLER SHALL NOT BE LIABLE FOR ERRORS OR OMISSIONS CONTAINED IN THIS MANUAL AND
SHALL NOT BE LIABLE FOR ANY CONSEQUENTIAL DAMAGES, WHICH MAY RESULT FROM THE PERFORMANCE OR USE OF
THIS MANUAL.

The information in this user’s manual is protected by copyright laws. No part of this manual may be photocopied or reproduced in any form
without prior written authorization from the copyright owners.

Copyright March, 2005
All rights reserved.

Microsoft and Windows are registered trademarks of Microsoft Corporation. DOS, Windows 95/98/ME/2000/NT/XP are trademarks of
Microsoft Corporation.

Product names mentioned herein may be trademarks and/or registered trademarks of their respective owners/companies.

The software described in this manual is delivered under a license agreement. The software may be used or copied only in accordance with
the terms of the agreement.

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this
copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless
otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
.

Rev 1.4

i -2

TABLE OF CONTENTS

PREFACE

Symbols and Conventions
Protecting Your Computer - Avoid Abusive Handling and Adverse Environment
Chapter Summaries

1. GETTING TO KNOW THE BASICS

Performance Feature
System at a Glance

Top View
Front and Rear View s
Side View s
Bottom View
AC Adapter
LED Status Indicators

Keyboard Features

Function (Q uick) Keys
Windows Keys

Embedded Numeric Keypad
Touch Pad
Graphic Subsystem

Adjusting the Display Brightness

Extending the Life of the TFT Display Panel

Opening and Closing the Display Panel
Audio Subsyste

Adjusting the Volume in Windows

Voice Recording
Modem and Modem Setting
Ethernet Adapte

2. BIOS SETUP AND SECURITY

Entering the BIOS Setup Screen
Leaving the BIOS Setup Screen
BIOS Action Key
Mo difying the BIOS Settings

Main Setu

Advance Setup

Boot Setup

Security Setup

Power Setup

Exit Setup

3. BATTERY POWER & POWER MANAGEMENT

The Battery Pack

Lithium -Ion Battery Technology

Battery Low-Power Warnin
Installing and Removing the Battery Pack
Charging the Battery and Charging Time
Checking the Battery Leve
Prolonging the Battery’s Life and Usage Cycles

i -3

Using Windows Power Options

Windows’ Power Scheme

Suspend Mode

Power Button Action

Low Battery Warning

Power Manual Quick Access

4. UPGRADING YOUR COMPUTER

Upgrading the System Memory

5. TROUBLE-SHOOTING

First Step
Audio Problem
Hard Disk Problem
Optical Drive Problem
Display Problem
Keyboard and Mouse Problem
CMOS Battery Problem
Memory Problem
Modem Problem
Network Adapter / Ethernet Problem
PC Card / PCMCIA Problem
Performance Problem
FireWire (IEEE1394) and USB 2.0 Problem

APPENDIX A Product Specification
APPENDIX B Agency Regulatory Notices

i -4

Preface

Using This Manual

This User’s Manual contains general information about the hardware and software setup, troubleshooting, and
technical specifications of the notebook computer.

Symbols and Conventions

The following conventions and symbols are used in this manual:

n When keys are to be pressed at the same time, a plus (+) symbol is used. For instance, Fn+F7 means

holding Fn and F7 keys at the same time.

n When a series of clicking actions is needed in Windows O/S, [ ] and > symbols are used. For instance,

[Start > Settings > Control Panel > Display] means clicking the Start icon first, then the Settings, then the
Control Panel, then the Display icon.

n When you need to make a selection with the touch pad (or mouse), you will be asked to ’select’ or ‘click’ or

‘double-click’, ‘right-click’ the item.

Note: Text in this format and symbol means specific instructions, commentary, sidelights, or any additional information or notes that you

should be aware of.

Warning: Text in this format and symbol means that failures to comply with the given instructions or information could result in damage to

your computer or could cause bodily harm or loss of life.

i -5

Protecting Your Computer - Avoid Abusive Handling and Adverse Environment

Following the advice below will help ensure that you get the most out of your Investment.

Your computer will serve you well if you take good care of it.

n Do not expose the computer to direct sunlight or place it near sources of heat.
n Do not subject it to temperatures below 0oC (32oF) or above 30oC (86oF).
n Do not expose the computer to magnetic fields.
n Do not expose the computer to moisture or rain.
n Do not spill water or liquid on the computer.
n Do not subject the computer to adverse shock and vibration.
n Do not expose the computer to dust and dirt.
n Do not place heavy objects on top of the computer.
n Do not place the computer on rocky surfaces.

Here are some ways of taking care of your AC adapter.

n Do not connect the adapter to any devices other than your computer.
n Do not let water get into the adapter.
n Do not block the ventilation airway of the adapter.
n Keep the adapter in a cool and ventilated place.
n Do not step on the power cord or place heavy objects on top of it.
n Carefully tuck away the power cord and any cables away from pedestrian traffic.
n When unplugging the power cord, do not pull on the cord itself but pull on the plug.
n Keep the adapter away from children.
n The total ampere ratings of the equipment plugged in should not exceed the ampere rating of the cord if

you are using an extension cord.

n The total current rating of all equipment plugged into a single wall outlet should not exceed the fuse rating.
n Do not connect other AC adapters to your notebook. This Notebook uses exclusively the AC adapter: Liteon

PA-1650-01 (65W)

When cleaning the computer, observe these steps:

1. Power off the computer and remove the battery pack.

2. Disconnect the AC adapter.

3. Use a soft cloth dampened with water. Do not use liquid or aerosol cleaners.

Contact your dealer or see your service technician if any of the following occurs:

n Computer has been dropped or the body has been damaged.
n Liquid has been spilled into the product.
n The computer does not operate normally.

Cleaning the Ventilation Grills:
It is suggested that you clean the ventilation grills regularly to maintain optimal thermal regulation of the
notebook. To do this, you may use a soft brush or a vacuum cleaner (with appropriate head adapter) to remove
the dust buildup on the ventilation grills.

i -6

Chapter Summaries

The following is a summary of the available chapters and appendices in this manual.
Chapter 1: Getting to Know the Basics

In this chapter, you will learn the basic operations and features of your computer. It gives you a general
understanding of the components of your computer.

Chapter 2: BIOS Setup / Security
In this chapter, you will learn how to change various firmware settings and what the settings mean. Also,
you will learn how to take advantage of the built-in security feature provided by the BIOS.

Chapter 3: Battery Power & Power Management
In this chapter, you will learn the fundamentals of power management and how to use them to achieve
longer battery life.

Chapter 4: Upgrading Your Computer
In this chapter, you will learn how to upgrade the system memory.

Chapter 5: Trouble-Shooting
In this chapter, you will learn how to solve common hardware and software problems.

Appendix A: Product Specification
In this section, you will find a list of the computer’s system specifications.

Appendix B: Agency Regulatory Notices
In this section, you will find the general electro-magnetic and safety regulatory information.

i -7

■ chapter 1 getting to know the basics

CHAPTER ONE

GETTING TO KNOW THE BASICS

This chapter introduces the features and components of the computer.

1-1

■ chapter 1 getting to know the basics

Performance Features

 Windows Media® Player Quick Launch
One button lets you play movies, or music by quickly launching Windows Media® Player

 High Performance Intel Processor with 915GM Chipset

The notebook PC is equipped with a powerful Mobile Intel Pentium M or Celeron M processor. Together
with the latest Intel 915GM chipset and technologies, the system offers a very advanced PC
performance.

 Advanced Graphics Engine

The integrated Intel GMA 900 high-end graphic engine offers excellent video performance for the most
demanding professional. The advanced graphic chip also incorporates a hardware-based
motion-compensation engine, which gives you smooth MPEG video playback. DirectX 9 graphics
capability also adds realism to PC games.

 AveraBrite™ LCD Display

The computer is equipped with a wide 13.3-inch TFT high-resolution display panel for clear text and
brilliant colors.

 Expandability

The system offers 2 upgradeable DDR SDRAM sockets for expansion, allowing the user to easily
increase the system’s capacity as the need arises.

 Built-in Multiple Card Reader

There is a built-in 4-in-1 card reader to access many of the portable media formats (SD Card, MMC
Card, MS and MS Pro Card).

 Ethernet Port

The system provides a built-in Ethernet network adapter for high bandwidth network connection.

 FireWire (IEEE1394 / 1394a) and USB 2.0 ports

In addition to a full array of built-in I/O por
connection to high bandwidth digital video devices and USB2.0 ports to connect to any USB-based
peripheral device.

 Wireless LAN

The internal Wireless LAN module allows your notebook to connect wirelessly to other 802.11-enabled
systems, devices or networks.

ts, the computer offers IEEE1394 for ultra high-speed

1-2

■ chapter 1 getting to know the basics

System At A Glance

Top View

1. AveraBrite™ LCD Display

The panel is where the system content is displayed.

2. Keyboard

The keyboard is used to enter data. It has an embedded numeric keypad and cursor control keys. (See
Keyboard Section for details.)

3. Touch Pad

The touch pad is a built-in pointing device with functions similar to a mouse.

4. LED Status Indicator

The LED Status indicators reveal the status of these functions: Numeric keypad, cap lock, scroll lock,
WLAN, ODD and HDD. (See the LED Status Indicator Section for details.)
The LED Status indicators also reveal the status of the system power state and battery-charging state. See
the LED Status Indicator Section for details.

5. Power / Suspend Button

The power/suspend button turns the notebook on and off and it also acts as a system standby key. Press
momentarily to turn on the system. Press and hold for at least 4 seconds to turn off the system. How this
key behaves can be defined in [Start > Settings > Control Panel > Performance and Maintenance > Power

1-3

■ chapter 1 getting to know the basics

Options > Advanced] menu. Press the power / suspend button again to return from the suspend mode.
(See Chapter 3 for more details on system suspend function.)

6. Battery Saver Mode Button

Pressing the key enables the system to lower its power usage; therefore the fan speed is reduced to
achieve the lowest operating noise.
You may need to go to BIOS Setup to enable Battery Saver Mode for this button. See Chapter 2 for details.

7. Windows Media® Player Launch Key

Pressing the key launches a multimedia application that allows you to watch DVD movies or, listen to music
from the optical drive.

Front and Rear Views

Warning:

Do not place any heavy objects on the top of notebook. This may damage the display

1. Built-in Stereo Speakers

The built-in speakers output the sound in stereo.

2. Microphone Jack

The microphone jack (3.5-mm diameter) is where you connect a microphone.

3. Stereo Headphone

The stereo headphone jack (3.5-mm diameter) is where you connect the headphones or external speakers.

4. Wireless On/Off Switch

Use the Switch to disable or enable the Wireless function.

5. Kensington Lock Key Hole

A Kensington-type security lock latches to this keyhole for anti-theft purpose.

1-4

■ chapter 1 getting to know the basics

6. Battery Pack

The battery pack is a built-in power source for the notebook.

7. Power Jack (DC-in)

The DC-out jack of the AC Adapter connects here and powers the computer.

8. External VGA Port

The VGA video output port is for connecting the external LCD monitor or projector.

Side Views

Warning:

Do not place any heavy objects on the top of notebook. This may damage the display

1. USB 2.0 Port (x3)

The Universal Serial Bus (USB2.0-compliant) port allows you to connect a wide variety of devices to your

computer at a rate of up to 480 Mbps. This port conforms to the latest USB2.0 plug-and-play standards.

2. 4-in-1 Card Reader

The 4-in-1 Card Reader supports SD Card, MMC Card, MS and MS Pro Card.

3. Optical Drive and Disk Eject Button and Manual Eject Key Hole

If your computer comes with the Combo drive, DVD-RW, DVD+RW, or DVD-Dual drive, you may save data
onto a CD-R, CD-RW,,DVD+/-R and DVD+/-RW disc. Press the eject button to eject the disk tray. The
manual eject keyhole allows you to manually eject a jammed disk.

4. Modem Port

This is where you plug the phone jack (RJ-11) for fax/modem functions.

5. Ventilation Grill

The fan grill is where air is exchanged to dissipate the internal heat. Do not block this airway completely.

6. Ethernet / LAN Port

1-5

■ chapter 1 getting to know the basics

The port connects to a network hub via the RJ-45 cable and also conforms to the 10/100Base-TX
transmission protocol.

7. TV (S-Video) Port

The S-Video port permits you to redirect the screen output to a television set or any analog video playback
device. This TV Port is copyright protected. When a DVD movie is played, the output is scrambled to
prevent analog recording.

8. FireWire / IEEE1394 / 1394a Port

This is a high-speed serial data port. You may connect any Fire-wire-ready device to this port.

9. PC Card Slot (Type II PCMCIA) and Card Eject Button
The slot is where a PC Card (Type II PCMCIA) is inserted. Press the eject button to release the PC Card.

Bottom View

1. Battery Pack and Battery Latch

The battery pack is a built-in power source for the notebook. Slide the battery latch to release the battery
pack.

1-6

■ chapter 1 getting to know the basics

2. System Device Cover

The system’s processor with cooler assembly, Wireless LAN module, HDD and memory module are located

under the case cover. The system memory and hard disk drive can be upgraded to a larger capacity. (See

Chapter 4 for instructions on a memory upgrade.)

3. Ventilation Grill

The fan grill is where air is exchanged to dissipate the internal heat. Do not block this airway completely.

Warning:

Do not block the Fan Grill outlet. Place the machine on hard surface only. The bottom case may get very hot.

AC Adapter

1. DC-out Connector

The DC-out connector docks to the power jack (DC-in) on the computer.

2. Adapter

The adapter converts alternating current into constant DC voltage for the computer.

3. AC Plug

The AC plug to the AC wall outlet.

Warning:

sensation on any of the computer’s metal parts such as the I/O ports. This is caused by leakage current when the AC adapter is not

properly grounded (via the ground pin). However, the amount of leakage current is within the safety regulation and is not harmful to the

human body.

Make sure you are using a standard 2-prong AC wall socket with a ground pin. If not, you may feel a slight tingling

1-7

■ chapter 1 getting to know the basics

LED Status Indicator

The LED Status Indicator displays the operating status of your notebook. When a certain function is

enabled, an LED will light up. The following section describes its indication.

System & Power Status Indicators

LED Graphic

Symbol

Indication

Blue light indicates the notebook is ON.
Blinking blue light indicates the notebook

is in suspend mode.

Orange light indicates the battery is being
charged.

Blinking orange light indicates the battery
level is low.

Green light indicates the battery is fully
charged.

Blue light indicates the WLAN module is
active.

Green light indicates the hard drive and/or
optical drive is being accessed.
Green light indicates the numeric keypad
is activated.

Green light indicates the cap-lock is
activated.

Green light indicates the Battery Saver
mode is enabled.

1-8

■ chapter 1 getting to know the basics

Keyboard Features

Function Keys (Quick Keys)

Graphic

Symbol

For various system controls, press the Fn (Function) key and the Fx key simultaneously.

Action System Control

Fn + F3 Turns off the LCD backlight.

Fn + F4 Enters Suspend Mode.

Fn + F5 Changes Display Mode:

Fn + F6 Decreases Display Brightness.

Fn + F7 Increases Display Brightness.

Fn + F8 Turns Speaker Volume down.

Fn + F9 Turns Speaker Volume up.

Fn + F10 Turns off the Speaker Volume.

Fn + Num
Lk

Fn + Scr Lk Press the Scroll Lock key and

LCD-only, CRT-only and
LCD&CRT.

Enables the embedded keypad
to work in numeric mode. The
keys act like numeric keypads
in a calculator. Use this mode
when you need to do a lot of
numeric data entry. An
alternative would be to connect
an external numeric keypad.

then press ↑or ↓to move one
line up or down.

1-9

■ chapter 1 getting to know the basics

Windows Keys

Your keyboard also has two Windows keys:

1. Start Key

This key allows you to pull up the Windows Start Menu at the bottom of the taskbar.

2. Application Menu Key

This key brings up the popup menu for the application, similar to a click of the right mouse button.

Embedded Numeric Keypad

Press Fn+NumLk to enable the embedded numeric keypad. The numbers are printed in the upper right

corner of a key, in a color different from the alphabets. This key pad is complete with arithmetic operators (+,

-, * , /).

Press Fn+NumLk to revert to normal character keys.

1-10

■ chapter 1 getting to know the basics

Touch Pad

The built-in touch pad, which is a PS/2-compatible pointing device, senses movement on its surface. As you
move your fingertip on the surface of the pad, the cursor responds accordingly.

The following items teach you how to use the touch pad:

1. Move your finger across the touch pad to move the cursor.

2. Press buttons to select or execute functions. These two buttons are similar to the left and right buttons on a

mouse. Tapping on the touch pad twice is similar to clicking the left button of a mouse.

Function Left Button Right

Button

Execution Click twice

quickly

Selection Click once Tap once
Drag Click and hold

to drag the

cursor
Access
Context Menu

Click once

Tap twice (at the same speed as

Tap twice quickly and on the

Tips on Using the Touch Pad:

1. The double-click speed is timed. If you double-click too slowly, your notebook responds as if you
single-clicked twice.

2. Keep your fingers dry and clean when using the touch pad. Also keep the surface of touch pad clean and
dry to prolong its life.

3. The touch pad is sensitive to finger movements. Hence, the lighter the touch, the better the response.
Heavy touch does not produce better response.

Equivalent Tapping Action

double-clicking
the mouse button)

second tap hold finger to the touch
pad to drag the cursor

1-11

■ chapter 1 getting to know the basics

Graphic Subsystem

Your computer uses a high performance 13-inch active matrix TFT panel with high resolution and multi-million
colors for comfortable viewing. The integrated Intel GMA 900 video graphics accelerator, which is Microsoft
DirectX 9 compatible, performs graphic rendering at a lighting-fast speed.

Adjusting the Display Brightness

The notebook uses special key combinations, called hot keys, to control brightness.
Press Fn+F7 to increase the brightness.
Press Fn+F6 to decrease the brightness.

Note:

To maximize your battery operating time, set the brightness to the lowest comfortable setting, so that the internal backlight

uses less power.

Extending the Life of the TFT Display Device

Observe the following guidelines to maximize the life of the backlight in the display.

1. Set the brightness to the lowest comfortable setting (Fn+F6).

2. When working at your desk, connect your notebook to an external monitor and disable the internal
display Fn+ F5.

3. Do not disable the suspend time-outs.

4. If you are using AC power and have no external monitor attached, change to suspend mode when not
in use.

Opening and Closing the Display Panel

To open the display, push the LCD latch inwardly and lift up the lid. Then tilt it to a comfortable viewing
position.

To close the display cover, fold it down gently until the LCD latche clicks into place.

Warning:

display is closed

To avoid damaging the display, do not slam it when closing. Do not place any object on top of the computer when the

1-12

■ chapter 1 getting to know the basics

Audio Subsystem

Your computer’s audio subsystem is Sound Blaster Pro-compatible.

Adjusting the Volume Manually

To increase the volume, press Fn+F9.

To decrease the volume, press Fn+F8.

Adjusting the Audio Volume in Windows

1. Click the speaker symbol in the task tray in Windows.

2. Drag the volume control bar up or down to adjust the volume.

3. To temporarily silence the speaker without changing the volume setting, click Mute.

Voice Recording

You will need to plug-in an external microphone to the microphone connector to record sound. You will need

to use audio processing software to enable the built-in microphone. For example, you may use Microsoft

Sound Recorder.

1-13

■ chapter 1 getting to know the basics

Modem

Your computer comes with a 56K V.92 internal fax/modem and a phone jack (RJ-11), which is located on the left side of
your computer.
Use a telephone cable to connect the computer to the telephone wall outlet.

Connecting the Modem

1. Plug one end of the phone line into the modem port located on the rear side of the computer.

2. Plug the other end of the line into the analog phone wall outlet.

Depending on where your computer is used, you may need to change settings in the modem. The correct setting will
allow you to maintain a stable connection in a country where its telecommunication system may be different to others.

To change the modem setting, do the following:

1. Go to [Start > Settings > Control Panel > Printers and Other Hardware] and double-click on Phone and
Modem Options icon. You will see a similar dialog box.

2. Click on the pull-down menu and select the country where it is applicable. Click on OK to exit.

1-14

■ chapter 1 getting to know the basics

Ethernet

Your computer is equipped with a 10/100Base-TX Fast Ethernet network adapter. Connect the active LAN cable

to the RJ-45 LAN port located on the right side of the computer. This allows you to access and transmit data in

the local area network.

Connecting to the Network

Use Unshielded Twisted Pair (UTP) Ethernet cable only.

1. Insert one end of the UTP cable into the network connector until the connector snaps securely into the

receptacle.

2. Either connect the other end of the cable to an RJ-45 jack wall outlet or to an RJ-45 port on a UTP

concentrator or hub in the network.

Cabling Restriction for Networks

The following restrictions should be observed for 100BASE-TX networks:

 The maximum cable run length is 100 meters(m) (328 feet[ft]).

 For 100-Mbps operations, use Category 5 wiring and connections.

Note:

Consult Windows manual and / or Novell Netware user’s guide for the software installation, configuration and operation of the

network.

1-15

¦ chapter 2 bios setup and security feature

CHAPTER TWO

BIOS SETUP AND SECURITY FEATURE

In this chapter, you will learn how to enter the BIOS Setup Menu and manipulate
various hardware control settings. You will also learn how to use the built-in security
features.

2-1

¦ chapter 2 bios setup and security feature

The Setup Utility is a hardware configuration program built into your computer’s BIOS (Basic Input/Output

System). It runs and maintains a variety of hardware functions. It is a menu-driven software, which allows you to
easily configure and change the settings.

The BIOS contains manufacture’s default settings for the computer’s standard operations. However, there are
occasions when you may be required to modify the default settings in the BIOS. For example, you may need to
configure the BIOS power management (APM) settings if you are using DOS, or non-Windows operating
system.

The BIOS allows you to set up passwords to limit access to users. This is an important feature because a great
deal of vital information is carried within the computer nowadays. Unauthorized access can be prevented. Later
in this chapter, you will learn how to use this security feature.

2-2

¦ chapter 2 bios setup and security feature

previous menu OR exits the BIOS setup

Entering the BIOS Setup Screen

First turn on the notebook and press F2 key quickly to access the BIOS Setup Utility.

Note: You may need to press F2 key fairly quickly. Once the system begins to load Windows, you may have to retry by cycling the power.

Leaving the BIOS Setup Screen

When you finish modifying the BIOS settings, exit the BIOS Setup Utility.

BIOS Action Keys

Function Key Command Description

Leaves a sub-menu to return to the

ESC Exit

while saving changes.
Enter Go to Sub Screen Shows the Sub Menu
F1 General Help Shows the Help Screen

F10 Save and Exit
<Tab> Select a field Selects the next field.

? Select an item Selects the next upper item.
? Select an item Selects the next lower item.

- Lower value Selects the next value within a field.
+ Higher value Selects the next value within a field.

Saves changes and reboots the

computer.

2-3

¦ chapter 2 bios setup and security feature

Modifying the BIOS Settings

The AMIBIOS setup main menu is subdivided into sub-menus. Each menu item is described in this section.

Main Setup

Under this menu, you may change time/date and view basic processor and system memory information.

Item Selections /

Sub-menu

Date N/A Type in the current date, in MM/DD/YY
Time N/A Type in the current date, in HH:MM:SS

Description

format.
format.

Advanced Setup

IDE Configuration

Item

Primary
IDE
Master
Secondary
IDE
Master

Note: The sub-menu is not selectable. Press enter to view information of the storage device.

Item

LCD Auto
DIMM
Function

LCD
Backlight
Saver

2-4

Selections /
Sub-menu

Hard Disk Primary Master is where the HDD is

ATAPI CDROM The secondary master controls the

Selections /
Sub-menu

Enable
Disable

Enable
Disable

Description

connected.

ATAPI CD-ROM drive.

Description

[Enable]: The system automatically
reduces the LCD brightness when AC
power is removed to save power.
[Disable]: The LCD brightness remains
the same whether or not AC power is
present.
[Enable]: The system automatically
reduces the LCD brightness when AC
power is removed and the keyboard or
touchpad has been idle for more than
10 minutes.
[Disable]: The LCD Backlight Saver
function is disabled.

¦ chapter 2 bios setup and security feature

Supervisor

Boot Setup

Boot Device Priority

Item

Selections /

Description

Sub-menu

1st Boot Device

Removable Dev.

Set the type of device for the first boot device.

CD/DVD

2nd Boot Device
3rd Boot Device
4th Boot Device

Hard Drive

Realtek Boot Agent
Disabled

Set the second boot device.
Set the third boot device.
Set the fourth boot device.

Note: If you select Realtek Boot Agent, the system will attempt to boot from the network.
Note: When the computer is first turned ON, you may also press F12 Key to enable the Boot Device selection menu. You may choose

CD/DVD, Hard Drive, or Realtek Boot Agent as the first storage device to boot from. If you have already connected a USB Floppy Disk
Drive before powering up, it will appear as a Removable Device in the Boot Device selection menu

Security Setup

Boot Settings Configuration

Item

Change

Selections /
Sub-menu

N/A Install or Change the Password

Description

Password
Change

N/A Install or Change the Password
User
Password

Boot
Sector
Virus
Protection

Disabled

Enabled

To enable or disable the boot sector
protection.
When Enabled, BIOS gives a warning
when any program attempts to rewrite
or delete the boot sector.

Note: About Boot Sector Virus Protection:

If enabled, the following warning message appears when a program attempts to alter the boot sector. You may have to enter “N” several
times to prevent the boot sector write.
Boot Sector Write!!!
Possible VIRUS: Continue (Y/N)? _
The following warning message appears when a program attempts to format the hard disk drive.
Format!!!
Possible VIRUS: Continue (Y/N)? _

2-5

¦ chapter 2 bios setup and security feature

Using Password Protection

Two Levels of Password Protection are available. The BIOS provides both a Supervisor and a User password. If
you try to activate both passwords, the Supervisor password must be set first.
The passwords activate two different levels of protection:

1. System always asks for password every time it is powered on.

2. System asks for password only when you attempt to enter BIOS utility.
The passwords are encrypted and stored in NVRAM. Make sure you write them down or memorize them. If you
lose the passwords, the computer may need to be sent back to the factory or an authorized service dealer to
reset the passwords.

Power Setup

Item

Intel
SpeedStep
tech.

Power Button
Mode

Long Battery
Life Mode

Selections /
Sub-menu

Maximum
Speed

Minimum
Speed

Automatic
Disabled

On/Off
Suspend

Enable
Disable

Description

[Maximum speed]: CPU performance is
maximized.

[Minimum Speed]: CPU performance is
minimized to save battery life.

[Automatic]: CPU adjusts its frequency
automatically (on AC power or battery
power) to save battery life.

[Disabled]: SpeedStep function is
disabled.

[On/Off]: When the power button is
pressed, the system is turned off.

[Suspend]: When the power button is
pressed, the system enters the suspend
mode.

When Enabled, maximum battery life
can be achieved. The processor
performance is lowered.

Note: The Suspend Mode selection in BIOS only applies to older Windows version (such as Windows 3.1 or Windows 95 or NT4) or

non-Windows operating system. In Windows ME / 98SE / 2000 / XP, suspend mode and settings are determined by settings in the Power
Options Properties (Start > Control Panel > Power Options).

Note: By default, both the Long Battery Life Mode and High Performance Mode are enabled. In this combination, when the notebook is on

AC power, it enters Higher Performance Mode automatically, and when the notebook is on battery power, it enters Long Battery Life Mode.

2-6

¦ chapter 2 bios setup and security feature

F10 key can be

setup questions. F9 key can be used for

Exit Setup

Item

Saves
Changes and
Exit

Discard
Changes

Load Optimal
Defaults

Selections /
Sub-menu

N/A

N/A

N/A

Description

After you have completed the BIOS
settings, select this item to save all
settings, exit BIOS Setup utility, and
reboot. New system settings will take
effect on next power-up.
used for this operation.

Discards changes done so far to any of
the setup questions.

Load Optimal Default value for all the
this operation.

2-7

¦ chapter 3 battery power & power management

CHAPTER THREE

BATTERY POWER & POWER MANAGEMENT

In this chapter, you will learn the fundamentals of power management and how to
use it to achieve longer battery life.

3-1

¦ chapter 3 battery power & power management

In this chapter, you will learn how to operate your notebook on battery power, how to handle and maintain the

battery pack, and learn about the system’s power saving features.

The LCD display, CPU and hard disk drive are the major hardware components that consume the most power.
Power management deals with how these key components should behave to conserve power. For example,
you can have the system turn off its display after 2 minutes of inactivity to save power. Efficient power
management can help you work longer sessions before having to recharge the battery.

The Battery Pack

Lithium-Ion Battery

Your notebook uses a six-cell Lithium-Ion battery pack that provides power when you don’t have
access to an AC outlet.

Note: It is necessary that you charge the battery pack for at least 6 hours before using it for the first time.
Note: In the Standby Suspend mode, a fully charged battery loses its power in roughly 1/2 day or less. When not being used,

the battery’s power will deplete in 1-2 month(s).

3-2

¦ chapter 3 battery power & power management

Battery Low-Power Warning

1. Low Battery Warning
Low battery condition occurs when battery power is reduced to 6%. The red battery status LED
indicator blinks and the system beeps once every 16 seconds or so.

2. Very Low Battery Warning
Very Low battery condition occurs at 3 % power remaining. The red battery status LED indicator
blinks and the system beeps at 4-second intervals.

When the notebook warns you of its low battery condition, you will only have a few minutes to save
your current work.

Warning: Do not expose battery packs to temperatures below 0 degree Celsius (32 degree F) or above 60 degree C (140F).

This may adversely affect the battery pack.

Note: Press Fn+F3 to turn off the battery warning beep.

3-3

¦ chapter 3 battery power & power management

Installing and Removing the Battery Pack

To Remove the Battery Pack:

1. Place the notebook bottom-side up on a flat and secured surface.

2. Push the latch and pull the battery’s hard case away from the notebook.

3-4

¦ chapter 3 battery power & power management

To Install the Battery Pack:

1. Place the notebook bottom-side up on a flat and secured surface.

2. Carefully insert the battery pack into the battery compartment of the notebook.

Charging the Battery and Charging Time

To charge the battery while it is in the notebook, plug the AC adapter into the notebook and an electrical
outlet.
The charging time is approximately 4-6 hours when the notebook is turned off and approximately 6-10
hours when the notebook is turned on.
When the battery is fully charged, the battery charge indicator becomes green.

Note: If system runs at heavy loading or in a high temperature environment, the battery may not be fully charged. You need to

continue to charge it with the AC adapter plugged in until the charging LED turns green.

3-5

¦ chapter 3 battery power & power management

Checking the Battery Level

You can check the remaining battery power in the Windows battery status indicator, which is located at the
lower right-hand corner of the task bar. (If you do not see a battery or AC-in icon on the task tray, go to
Power Options Properties box and click on the Advanced tab. Check off ``Always show icon on the task
bar``.)
Alternatively, you can access the power meter by clicking the Power Options icon in the Windows Control
Panel.

Prolonging the Battery’s Life and Usage Cycles

There are ways you can prolong battery life.
n Use the AC adapter wherever an AC wall outlet is available. This will ensure uninterrupted

computing.

n Purchase an additional battery pack.
n Store the battery pack in room temperature. Higher temperature tends to deplete the battery’s power

faster.
n Make good use of the power management function. Save To Disk (Hibernate) saves the most energy
by storing current system contents in a hard disk space reserved for this function.

n The life expectancy of the battery is approximately 300 recharges.
n See the notices section in the beginning of the user manual on how to care for the battery pack.

Note: Read the Section about Protecting Your Notebook in the beginning of this manual for tips about how to maintain the battery

pack.

Note: To achieve optimal battery performance, you may need to do a battery calibration at a 3-month interval. To do this:

1. Fully charge the battery.

2. Then discharge the battery by entering the BIOS setup screen. (Press F2 key as soon as you turn on the computer. And let it
remain at the setup screen until the battery runs out.

3. Fully charge the battery again.

3-6

¦ chapter 3 battery power & power management

Using Windows Power Options

Windows Power Management provides basic power saving features. In the Windows Power Options
Properties [Start > Settings > Control Panel > Performance and Maintenance > Power Options] dialogue
box, you may enter time-out values for display and hard disk drive. Windows power manager saves power
by turning off the hard drive after 1 minute of inactivity, for example.

Windows’ Power Schemes

The power management control panel in Windows XP, known as Power Schemes, is designed to
provide the user with an easy-to-use interface. The Power Schemes tab can be found in the Power
Options Properties panel that is accessible via the control panel window.
Schemes are easy to understand, based on notebook usage scenarios, and control not only
processor power usage but other system peripherals as well.
Go to [Start > Settings > Control Panel > Performance and Maintenance] and double-click the Power
Options icon.

Always on mode puts the processor into maximum performance mode, which provides no power
saving. The other schemes control processor performance based on demand. For example, Max
Battery mode lowers the processor’s speed and voltage to conserve power as much as possible.

In this dialog box, you can manually set the LCD and hard drive’s time-out values in the “Plugged in”
column and in the “Running on batteries” column. Lower time-out values will conserve battery power.

Note: Also consult Windows user guide for more information on how to use Windows power management functions.
Note: Actual dialogue box shown above may appear slightly different.

3-7

¦ chapter 3 battery power & power management

Suspend Mode

Standby Suspend

The system automatically enters this mode after a period of inactivity, which is set in the Power Schemes
dialog box. In Standby mode, hardware devices, such as the display panel and hard disk, are turned off to
conserve energy.

Hibernate Suspend

In this mode, all system data is saved in the hard disk before powering down. When this mode is activated,
the system state and contents are saved to the hard disk drive after a period of inactivity defined by the
user. No power or very little power is drawn from the battery module under this mode.
However, depending on how much RAM that has been installed on your computer, the amount of time the
system requires to restore all its previous contents can range from 5 to 20 seconds.
For Windows 2000 / XP users, hibernation is handled by the operating system; therefore, no special disk
partition or disk file is necessary.
If you wish to activate Hibernate mode, you need enable Hibernate Support in the Hibernate tab of the
Power Options menu.

Note: Do not install or remove the memory module when the system is in the suspend mode.
Note: Actual dialogue box shown above may appear slightly different.

3-8

¦ chapter 3 battery power & power management

Power Button Action

The notebook PC’s power button can be set to turn off the system or activate the suspend mode.

Go to [Start > Settings > Control Panel > Performance and Maintenance > Power Options] and click
on the Advanced tab. In the pull-down menu, select how you wish the power button to work as.

Note: Actual dialogue box shown above may appear slightly different.

Warning: In the When I close the lid of my portable computer pull-down menu, DO NOT select Do nothing – otherwise the

system will still run at high speed while the processor’s fan grill is fully blocked by the closed LCD panel. The heat will damage
the LCD panel.

3-9

¦ chapter 3 battery power & power management

Low Battery Warning

You can define when and how the system warns you of its low battery condition.

Go to the Alarms tab in the Power Options Properties box. If you wish to hear audible beeps, click on
the Alarm Action button and put a check on Sound Alarm.

Note: Consult Windows user guide for more information on how to use Windows power management functions.
Note: Actual dialogue box shown above may appear slightly different.

3-10

¦ chapter 3 battery power & power management

Power Menu Quick Access

Instead of making specific selections in the Power Options Properties box, you can quickly and easily
specify which pre-set power saving function you desire by left clicking on the Battery icon at the lower
right-hand corner of the task bar. (If you do not see a battery or AC-in icon, go to Power Options
Properties box and click on the Advanced tab. Check off ``Always show icon on the task bar``.) Select
Max Battery if you want the system to enter suspend mode more often. Or, select Always On if your
notebook PC is plugged into an AC power source.

Note: Actual dialogue box shown above may appear slightly different.

3-11

¦ chapter 4 upgrading your computer

CHAPTER FOUR

UPGRADING YOUR COMPUTER

In this chapter, you will learn how to upgrade the DRAM.

Warning: We strongly recommend that you send your notebook back to the manufacturer for upgrading.
When you upgrade your system, please turn off the power, disconnect the LAN and Modem cable first
for your safety. After the system upgrade, please replace all the screws before turning on.

4-1

¦ chapter 4 upgrading your computer

Upgrading the System Memory

Many applications will generally run faster when the computer’s dynamic memory capacity is increased. The
computer provides two DDR memory sockets. There is one located underneath the System Device Cover and
another one located underneath the keyboard. You can increase the amount of memory by replacing the
existing one with a dual inline memory module (commonly known as SO-DIMM) of a higher capacity. The
SO-DIMM can be 256MB, or 512MB in capacity. The SO-DIMM is of type DDR1 has 200 pins and runs on 2.5V.

Warning: Memory upgrade is a delicate process. Please observe the following instructions carefully or have a qualified technician install

it for you. Damages due to mishandling of this procedure are NOT covered by the manufacture’s warranty.

Warning: Changing memory while your computer is in suspend or power-saving mode may cause permanent damage to the hardware.

Make sure you turn off the power and unplug the AC cord before proceeding with a memory upgrade.

Warning: You should only use the DIMM module that is approved; otherwise the system may become unstable.

4-2

¦ chapter 4 upgrading your computer

Installing a memory module (DIMM) into the system

To install the DIMM under the System Device Cover, do the following:

1. Power OFF the notebook. Unplug the AC cord and all cables/devices attached to the notebook.
Remove the battery.

2. Place your hand on a large metal object momentarily to discharge any static electricity. Place the
notebook on a flat surface and fully close the LCD lid.

3. Locate and remove 7 Screw A’s on the System Device Cover.

4. Remove the System Device Cover. The DIMM socket is now seen as shown below.

5. If you need to remove an old DIMM from the socket, press out on the latches located on both edges
of the socket at the same time. The DIMM should pop up to an angle of 30 degree (see diagram below).
Pull the DIMM module out of the memory socket. Store away the DIMM for future use.

4-3

¦ chapter 4 upgrading your computer

6. Install the new DIMM module into the memory socket. The DIMM will only fit in one way. Insert the
DIMM at an angle of approximately 30 degrees into the empty memory socket. Then press it firmly so that
the contact edge is driven into the receiving socket.

7. Pivot the DIMM until the latches on both sides of the socket snap into place.

Note: Notice the notch on the DIMM. The notches should fit in the socket.

8. Replace the System Device Cover back and tighten 7 Screw A’s.

4-4

¦ chapter 4 upgrading your computer

To install the DIMM under the keyboard, do the following:

1. Power OFF the notebook. Unplug the AC cord and all cables/devices attached to the notebook.
Remove the battery.

2. Place your hand on a large metal object momentarily to discharge any static electricity. Place the
notebook on a flat surface and fully close the LCD lid.

3. Follow the Step 3 and Step 4 from the previous section and remove Screw D.

4. Find the keyboard latches near the upper edge and the side edges of the keyboard. The latch is
spring-loaded. It will retract when pressed and revert back to its original position when released. Using a
small blade to press the latch inward. The keyboard tray should pop up slightly over the latch. If the
keyboard tray does not pop up, try to gently lift it up just over the latch. Repeat the step for the other
keyboard latches.

4. Carefully lift up the top edge and position the keyboard out of the way and the following is revealed.

4-5

¦ chapter 4 upgrading your computer

5. If you need to remove an old DIMM from the socket, press out on the latches located on both edges
of the socket at the same time. The DIMM should pop up to an angle of 30 degree (see diagram below).
Pull the DIMM module out of the memory socket. Store away the DIMM for the future use.

6. Install the new DIMM module into the memory socket. The DIMM will only fit in one way. Insert the
DIMM at an angle of approximately 30 degrees into the empty memory socket. Then press it firmly so that
the contact edge is driven into the receiving socket.

7. Pivot the DIMM until the latches on both sides of the socket snap into place.

Note: Notice the notch on the DIMM. The notches should fit nicely with the socket.

8. Put the keyboard back to its position. Make sure the upper edge of the keyboard now resides under
the spring-loaded latches. Re-attached Screw D. Put the System Device Cover back on and tighten 7
Screw A’s.

Congratulations! You have just completed the memory upgrade. When you boot up the computer, you
should expect to see an increase in DRAM capacity.

Note: Your computer has been tested with a wide range of DIMM on the market. However, not all memory modules are compatible.

Check with your system vendor for a list of compatible DIMM for your computer.

4-6

¦ chapter 5 trouble shooting

CHAPTER FIVE

TROUBLE SHOOTING

In this chapter, you will learn how to solve common hardware and software problems.

5-1

¦ chapter 5 trouble shooting

Your computer has been fully tested and complies with the system specifications before shipping. However,

incorrect operations and/or mishandling may cause problems.

This chapter provides a reference for identifying and correcting common hardware and software problems that
you may encounter.

When you encounter a problem, you should first try to go through the recommendations in this chapter. Instead
of returning the computer and waiting for repair, you may easily solve the problems by considering the following
scenarios and possible solutions. If the error continues, contact your reseller for service information.

Before taking further actions, consider the following suggestions:

n Check to see if the problem persists when all the external devices are removed.
n Check to see that the green light indicator on the AC adapter is lit.
n Check to see the power cord is properly plugged to the wall outlet and to the computer.
n Check to see the power indicator of the computer is on.
n Check to see if your keyboard is operational by pressing and holding any key.
n Check for any incorrect or loose cable connections. Make sure the latches on the connectors latch

securely on to the receptor end.
n Be sure you have not performed an incorrect setting on the hardware devices in the BIOS Setup utility. A
faulty setting may cause the system to misbehave. If you are not sure of the changes you made, try to restore
all the settings to factory defaults.
n Be sure all the device drivers are installed properly. For example, without the audio driver properly
installed, the speakers and microphone will not work.
n If external devices such as USB camera, scanner or printer do not function correctly when connected to
the system, it is usually the device’s own problem. Consult the device’s manufacturer first.
n Some software programs, which have not gone through rigorous coding and testing, may cause problems
during your routine use. Consult the software vendor for problem solving.
n Legacy peripheral are not plug-and-play capable. You need to restart the system with these devices
powered up and connected first.

n Be sure to go to BIOS SETUP and load DEFAULT SETTING after BIOS re-flash.
n Be sure the Quick Key Lockout Switch on the bottom of the computer is not engaged; otherwise the quick

keys will not work.

5-2

¦ chapter 5 trouble shooting

Audio Problems

No speaker output -

n Software volume control is turned down in Microsoft Sound System or is muted. Double-click the
speaker icon on the lower right corner of the taskbar to see if the speaker has been muted or turned down
all the way.
n Most audio problems are software-related. If your computer worked before, chances are the software
may have been set incorrectly.
n Go to [Start > Settings > Control Panel] and double-click the Sounds . Speech and Audio Devices icon.
In the Sounds and Audio Devices Properties box, make sure that Realtek AC97 Audio is the default
playback device.

Sound cannot be recorded -

n You will need to plug-in an external microphone to the microphone connector to record sound.
n Double-click the speaker icon on the lower right corner of the taskbar to see if the microphone has

been muted.

1. Click Options and select Properties.

2. Select Recording and click the OK button.

3. After Click OK button, the recording volume control panel will appear.
n Go to [Start > Settings > Control Panel > Sounds. Speech and Audio Devices] and double-click the
Sounds and Audio Devices icon. In the Volume or Audio page, make sure that Realtek AC97 Audio is the
default recording device.

5-3

¦ chapter 5 trouble shooting

Hard Disk Problems

The hard disk drive does not work or is not recognizable -

n
n The new HDD may need to be partitioned and reformatted. O/S and drivers will need to be

re-installed as well.
n Check the hard disk indicator LED. When you access a file, the LED lamp should light up
momentarily.

n The HDD may be defective.
n If your computer has been subjected to static electricity or physical shock, you may have damaged

the disk drive.

The hard drive is making abnormal whining noises -

n You should back up your files as soon as possible.
n Make sure the source of noise is indeed from the hard drive and not the fan or other devices.

The hard disk drive has reached its capacity -

n Run Disk Cleanup utility in Windows. [Start > All Programs > Accessories > System Tools > Disk
Cleanup] The system will prompt you for what to do.
n Archive files or programs that you no longer use by moving them to an alternative storage medium
(floppy disk, optical record-able disk, etc.) or uninstall programs that are no longer used.
n Many browsers store files in the hard drive as a cache to speed up the performance. Check the
program’s Online Help for instructions on decreasing the cache size or on removing temporary Internet
files.
n Empty the Recycle Bin to create more disk space. When you delete files, Windows saves them to the
Recycle Bin.

The hard disk takes longer to read a file -

n If you have been using the drive for a period, the files may be fragmented. Go to [Start > All Programs
> Accessories > System Tools > Disk Defragmenter] to perform a disk defragmentation. This operation may
take a while.
n Interrupted requests or problems with other hardware devices may have occupied the CPU and
therefore slowing down the system performance.

The files are corrupted -

n Run the Error-checking utility in Windows to check the HDD. Double-click My Computer. Right-click C:
and select Properties. Click Check Now in Error-checking in Tools.

5-4

¦ chapter 5 trouble shooting

Optical Drive Problems

The optical drive does not work -

n Try rebooting the system.
n The disk is damaged or files are not readable.
n After you have inserted a CD-ROM disk, it may take a moment before you can access its content.

The drive does not read any disks -

n The CD may not be properly seated in the tray. Make sure the disk is firmly seated onto the spindle.
n The disk is damaged or not readable.

The disk cannot be ejected -

n Normally, it takes a few seconds to eject the disk.
n If the disk cannot be ejected, it may be mechanically jammed. Straighten out a paper clip and insert it

into the tiny hole next to the eject button. This should eject the disk tray. If not, return the unit for repair. Do
not forcefully pull on the disk tray.

The DVD RW drive cannot record -

n Make sure that media is blank and not defective.

5-5

¦ chapter 5 trouble shooting

Display Problems

The display panel is blank when the system is turned on -

n Make sure the computer is not in the Standby or Hibernate suspend modes. The display is turned off
to conserve energy in these modes.

The screen is difficult to read -

n The display resolution should at least be set to at least 1280x800 for optimal viewing.

1. Go to [Start > Settings > Control Panel > Appearance and Themes] and double-click the Display icon.

2. Under the Settings page, set screen resolution to at least 1280x800 and choose at least 256 colors.

The screen flickers -

n It is normal if the display flickers a few times when shutting down or powering up.

Keyboard and Mouse Problems

The built-in touch pad performs erratically -

n Make sure there is no excess perspiration or humidity on your hand when using the touch pad. Keep
the surface of the touch pad clean and dry.
n Do not rest your palm or wrist on the surface of the touch pad while typing or using the touch pad.

The built-in keyboard accepts no input -

n If you are connecting an external keyboard to the system, the built-in keyboard may not work.
n Try restarting the system.

The characters on the screen repeat while I type.

n You may be holding the keys down too long while you’re typing.
n Keep the keyboard clean. Dust and dirt under the keys could cause them to stick.
n Configure the keyboard to wait longer before the auto repeat feature starts. To adjust this feature, Go

to [Start > Settings > Control Panel > Printers and Other Hardware], and double-click the Keyboard icon. A
dialogue box shows up with the adjustable settings for the keyboard.

5-6

¦ chapter 5 trouble shooting

CMOS Battery Problem

A message “CMOS Checksum Failure” displays during the booting process or the time (clock)
resets when booting -

n Try to reboot the system.
n If the message “CMOS Checksum Failure” appears during the booting procedure even after

rebooting, it may indicate failure of the CMOS battery. If so, you need to replace the battery. This battery
normally lasts two to five years. The battery is a type CR2032 (3V). You may replace it by yourself. The
battery is located under the System Device Cover on the bottom of the notebook. See Chapter 4 for more
details.

Memory Problems

The Operating System does not show an increased memory capacity when you have already
installed additional memory -

n Certain brands of memory module may not be compatible with your system. You should ask your
vendor for a list of compatible DIMM.
n The memory module may not be installed properly. Go back to Chapter 4 to review the details of this
operation.
n The memory module may be defective.

The Operating System issues an insufficient memory error message during operation -

n This is often a software or Windows-related problem. A program is draining the memory resources.
n Close the application programs you’re not using and restart the system.
n You need to install an additional memory module. For instructions, go to Chapter 4 Upgrading Your

Computer.

5-7

¦ chapter 5 trouble shooting

Modem Problems

The built-in modem does not respond -

n Make sure the modem driver is loaded properly.
n Go to [Start > Settings > Control Panel > Printers and Other Hardware > Phone and Modem Options]

and go to Modems tab. Make sure the 56K V.92 Modem is listed. Otherwise, click the Add button to add the
modem drive, which is located in the factory CD-ROM (or floppy diskette).
n Go to [Start > Settings > Control Panel > Performance and Maintenance > System] and click Device
Manager button in the Hardware page to check for possible resource or driver conflict. See Windows
on-line help or manual for how to handle such problems.
n Make sure the phone line, which the computer is connected to, is working.

Connection difficulties -

n Be sure to disable Call Waiting on the phone line.
n Be sure to have the correct country setting where your computer is used. [Start > Settings > Control

Panel > Printers and Other Hardware > Phone and Modem Options] In the Country/Area pull-down menu,
select the appropriate country setting.
n Excessive line noise might cause the connection to be dropped. To check this, put the regular phone
handset on the line and place a phone call. If you do hear abnormal noise, try to make the modem
connection with a different line or contact your local telephony company for service.

n Make sure the cable connection is firm.
n Try a different receiver number and see if the problem persists.

Network Adapter / Ethernet Problems

The Ethernet adapter does not work -

n Go to [Start > Settings > Control Panel > Performance and Maintenance > System > Hardware >
Device Manager]. Double-click on Network Adapters and check if Realtek RTL8139/810x Family Fast
Ethernet NIC appears as one of the adapters. If it does not exist, Windows has not detected the Realtek
RTL8139/810x Family Fast Ethernet NIC or the device driver has not been installed properly. If there is a
yellow mark or red-cross on the network adapter, it may be a device or resource conflict. Replace or update
the device driver from the factory CD-ROM disk or consult Windows manual on how to solve the resource
conflict problem.

n Make sure the physical connections on both ends of the cable are good.
n The hub or concentrator may not be working properly. Check to see if other workstations connected

to the same hub or concentrator are working.

The Ethernet adapter does not appear to operate in the 100Mbps transmission mode -

n Make sure the hub you are using supports 100Mbps operation.
n Make sure that your RJ-45 cable meets the 100Base-TX requirements.
n Make sure the Ethernet cable is connected to the hub? socket that supports 100Base-TX mode.

The hub may have both 100Base-TX and 100Base-T sockets.

5-8

¦ chapter 5 trouble shooting

PC Card / PCMCIA Problems

PC Cards do not function-

n Make sure you have properly installed the driver for the card.
n Consult the card’s manual or contact the vendor for trouble-shooting.

The PC card cannot be recognized -

n Windows NT4.0 does not support PCMCIA (PC Card) function. You may need an external program
for this.
n Make sure the card is fully inserted; the outer end of the card should be even with the edge of the
computer.

n Remove and insert the PC card again.
n Make sure there is no IRQ conflict with the card. See Windows on-line help for solving IRQ conflicts.
n Reboot the computer and see if the problem persists.
n The card may be defective. Try the card on another system, if possible.

Windows crashes or freezes when you remove the PC card-

n Make sure you <Stop> the PC card before removing it. Double-click the Safely Remove Hardware
icon at the lower right corner of the task bar and select the card you wish to stop. When you click <Close>,
in a few seconds Windows will prompt you to remove the card.

Performance Problems

The computer becomes hot -

n In a 35oC environment, certain areas of the computer’s back case are expected to reach 50 degrees.
n Make sure the air vents are not blocked.
n If the fan does not seem to be working at high temperatures (50 degrees Celsius and up), contact the

service center.
n Certain programs that are processor-intensive may increase the computer temperature to a degree
where the computer automatically slows down its CPU clock to protect itself from thermal damage.

The program appears stopped or runs very slowly -

n Press CTRL+ALT+DEL to see if an application is still responding.
n Restart the computer.
n This may be normal for Windows when it is processing other CPU-intensive programs in the

background or when the system is accessing slow-speed devices such the floppy disk drive.
n You may be running too many applications. Try to close some applications or increase system
memory for higher performance.
n The processor may have been overheated due to the system’s inability to regulate its internal heat.
Make sure the computer’s ventilation grills are not blocked.

5-9

¦ chapter 5 trouble shooting

FireWire (IEEE1394) and USB 2.0 Problems

The USB device does not work -

n Windows NT 4.0 does not support USB protocols
n Check the settings in the Windows Control Panel.
n Make sure you have installed the necessary device drivers.
n Contact the device vendor for additional support.

The IEEE1394 port does not work -

n Go to [Start > Settings > Control Panel > Performance and Maintenance > System > Hardware >
Device Manager]. You should see an entry which reads “Texas Instrument OHCI Compliant IEEE 1394 Host
Controllers”. If it does not exist, Windows has not detected the host controller or the device driver has not
been installed properly. If there is a yellow mark or red-cross on the 1394 host controller, it may be a device
or resource conflict. Replace or update the device driver from the factory CD-ROM disk or consult the
Windows manual on how to solve the resource conflict problem.

n Make sure the cable is fully connected.
n Make sure you have installed the necessary device drivers.
n Contact the device vendor for additional support.

5-10

■ appendix A product specification

A

APPENDIX A

PRODUCT SPECIFICATION

-1

■ appendix A product specification

A

 Processor

 Core Logic

Processor and Core Logic

Mobile Intel Pentium M or Mobile Intel Celeron M

Intel 915GM + ICH6-M (FW82801FBM) chipset with video, audio, modem, and USB2.0 controllers
integrated
533 MHz (Pentium M) / 400 MHz (Celeron M) Front Side Bus

 Memory Type
 Default
 Memory

Expansion

System Memory

DDR SDRAM 333MHz, PC2700
256 / 512MB, 2.5-Volt 64-bit bus
Two 200-pin DIMM sockets, Max 2 GB

 LCD Panel

 Graphic

Accelerator

 Motion

Playback

 Other

Features

 S-Video

TV-out Encoder

Display

13.3-inch (1280x800) WXGA TFT display with 24-bit colors

Intel® Graphics Media Accelerator 900

Hardware Motion Compensation and IDCT Supported for MPEG1/2 Playback
DirectX compatible

Integrated with graphics accelerator

-2

■ appendix A product specification

A

Audio

 Chipset
 Audio Codec
 Sound

Capabilities

 Chipset

 Transmission

Rate

 Module
 Transmission

Protocol

 Chipset

 PnP Function

 Flow Control
 Speed

Selection

 Other

Features

Intel (ICH6M) integrated audio controller
Realtek ALC655
DirectSound 3D, EAX 1.0 & 2.0 compatible
A3D, I3DL2 compatible
AC97 V2.3 compatible

7.1 Multi-channel compatible (through S/PDIF)
2 Stereo Speakers

Modem

Intel (ICH6M) integrated Modem Controller with MDC card, AC97 V2.2 Modem support
V.92 / V.90 / K56flex for download data speed up to 56Kbps.
V.34, V.17, V.29 protocol supported

Wireless LAN

Intel PRO/Wireless 2200 or MSI-6833A
MiniPCI Interface IEEE802.11 B&G

LAN / Ethernet

Realtek 8100CL Ethernet function for 10/100Base-TX network standards
Windows 2000 / XP Plug and Play compatible
Automatic Jam and auto-negotiation for flow control
Auto Negotiation and Parallel detection for automatic speed selection (IEEE 802.3u)
High performance 32-bit PCI bus master architecture with integrated DMA controller for low CPU
and bus utilization
Remote Wake-up Scheme supported
Hot Insertion supported

-3

■ appendix A product specification

A

 Chipset

 Capabilities

 Hard Drive

 DVD±R/±RW

or DVD-Dual or
DVD-Multi
Standards

 Keyboard

 Touch pad

 Chipset
 PC Card
 4-in-1 Card

Reader Format
Support

FireWire IEEE1394(a)

IEEE1394 OHCI Host Controller and
Up to 400 Mbps
Expandable up to 63 devices in chains

Storage

2.5-inch format hard disk drive

5.25-inch format (12.7mm height) fixed module (Optional Purchase)

Keyboard & Touch pad

86-key QWERTY keyboard with embedded numeric keypad and Windows keys, 19.05mm Pitch

Built-in Touch Pad

PC Card & Multiple Card Reader

OZ601 (PC Card), GL817E (Card Reader)
PC Card TYPE II, Hot insertion and removal supported
Multimedia Card (MMC), Secure Digital Card (SD), Memory Stick (MS), Memory Stick Pro (MS Pro)

 Mic-In Port
 Audio-Out / SPDIF
 FireWire
 USB 2.0 Port
 Ethernet
 Modem
 S-Video
 Power-In
 VGA Port
 Card Reader
 PC Card Slot

Ports and Connectors

One Microphone-in jack
One Headphone
One FireWire (IEEE1394) host connector
Three USB 2.0-compliant connectors
One standard network Ethernet connector (RJ-45)
One modem / phone connector (RJ11)
One S-video (TV-out) output connector
One DC-in connector
One 15-pin VGA connector
One 4-in-1 Card Reader slot
One PC Card Slot (type II)

-4

■ appendix A product specification

A

 Primary

Battery Pack

 Feature

 Adapter

AC-Input /
DC-Output

Battery Pack / AC Adapter

Li-Ion 6-Cell pack, 11.1V x 4400 mAh

Low battery state with low battery warning beep
Uniwill SmartPower II Power Management
Smart Battery Compliant; low battery warning beep
Long Battery Life Mode and Silent Mode

Auto sensing AC-in 100~240V, DC-out 19V, 65W

BIOS

 PnP Function
 Self Test
 Auto

Detection

 Power

Management

 Security
 Other

Features

Plug and Play BIOS
Power On Self Test
DRAM auto-detection, auto-sizing
L2 Cache auto-detection
Hard disk type auto-detection
APM 1.2 (Advanced Power Management) &
ACPI 2.0 (Advanced Configuration Power Interface)
Two Level Password Protections
32-bit access, Ultra DMA, PIO5 Mode support
Multi-boot capability

 O/S

Compatible with Microsoft Windows XP

Physical Specification

 Dimension
 Weight

 Environmental

Limits

12.44” (W) x 8.81” (D) x 1.25~1.35” (H) Inches

4.5 lbs. (with LCD, Optical Drive and 6-cell battery pack)

Operating Temperature: 5 to 30
Operating Humidity: 20 to 80 percent RH (5 to 35
Storage Temperature: -15 to 50

o

C (41 to 86oF)

o

C (-5 to 122oF)

o

C)

-5

¦ appendix B agency regulatory notices

APPENDIX B

AGENCY REGULATORY NOTICES

B-1

¦ appendix B agency regulatory notices

Federal Communications Commission Notice

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:

n Reorient or relocate the receiving antenna.
n Increase the separation between the equipment and the receiver.
n Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
n Consult the dealer or an experienced radio or television technician for help.

Modifications

The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly
approved by the Manufacture may void the user’s authority to operate the equipment.

Connections to Peripheral Devices

Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods to maintain
compliance with FCC Rules and Regulations.

Declaration of Conformity

This device complies with Part 15( CLASS B )/68 the FCC Rules. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.

European Notice

Products with the CE Marking comply with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC)
and R&TTE Directive (1999/5/EC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the following European Norms:

n EN55022 : 1998+A1: 2000+A2: 2003, CLASS B
n EN61000-3-2 : 2000
n EN61000-3-3 : 1995+A1: 2001
n EN55024 : 1998+A1 : 2001+A1: 2003
n IEC61000-4-2: 2001
n IEC61000-4-3:2002+A1:2002
n IEC61000-4-4:1995+A1:2000+A2:2001
n IEC61000-4-5:2001
n IEC61000-4-6:2001
n IEC61000-4-8:2001
n IEC61000-4-11:2001
n EN50082 (IEC801-2, IEC801-3, IEC801-4) Electro-magnetic Immunity
n EN 300 328-2, EN 300 328-1, EN 301 489-1, EN 301 489-17 (ETSI 300 328, ETSI 301 489) Electro-magnetic

Compatibility and Radio Spectrum Matter.

n TBR21 ( ETSI TBR21) Terminal Equipment.
n EN60950 (IEC60950) I.T.E. Product Safety

Canadian Notice

This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus as set out in the
radio interference regulations of the Canadian Department of Communications.

Le present appareil numerique nemet pas de bruits radioelectriques depassant les limites applicables aux appareils
numeriques de Classe B prescrites dans le reglement sur le brouillage radioelectrique edicte par le Ministere des
Communications du Canada.

Power Cord Requirement

The power cord supplied with the AC adapter should match the plug and voltage requirements for your local area.
Regulatory approval for the AC adapter has been obtained using the power cord for the local area. However, if you travel to
a different area and need to connect to a different outlet or voltage, you should use one of the power cords listed below. To

B-2

¦ appendix B agency regulatory notices

purchase a power cord (including one for a country not listed below) or a replacement ac adapter, contact your local dealer.

U.S. and Canada

n The cord set must be UL-Listed and CSA-Certified or C-UL Listed.
n The minimum specifications for the flexible cord are (1) No. 18 AWG, (2) Type SJ, and (3) 3-conductor.
n The cord set must have a rated current capacity of at least 10 A.
n The attachment plug must be an earth-grounding type with a NEMA 5-15P (15A, 125V) or NEMA 6-15P (15 A, 250V)

configuration.

Japan

n All components of the cord set (cord, connector, and plug) must bear a `PSE` mark and registration number in

accordance with the Japanese Dentori Law.

n The minimum specification for the flexible cord are: (1) 0.75 mm2 conductors, (2) Type VCT or VCTF, and (3)

3-conductor.

n The cord set must have minimum rated current capacity of 7 A.
n The attachment plug must be a two-pole, grounded type with a Japanese Industrial Standard C8303 (15 A, 125 VAC)

configuration.

Other Countries

n The cord set fittings must bear the certification mark of the agency responsible for evaluation in a specific country.

Acceptable agencies are:

BSI (UK)
OVE (Australia)
CEBEC (Belgium)
SEMKO (Sweden)
FIMKO (Finland)
DEMKO (Denmark)
NEMKO (Norway)
SETI (Finland)
EANSW (Australia)
SEV (Switzerland)
IMQ (Italy)
UTE (France)
CCC (China)
PSB (Singapore)
PSE (Japan)
BSMI (Taiwan)
B (Polish)
VDE (Germany)
SASO (Saudi Arabia)

n The flexible cord must be of a HAR (harmonized) type HO5VV-F 3-conductor cord with a minimum conductor size of

0.03 square inches.

n The minimum specification for the flexible cord for Class II product are: (1) 2X0.75 mm2 conductors, (2) 2-conductor

cord.

n The cord set must have a current capacity of at least 10 A and a nominal voltage rating of 125 / 250 VAC.

CAUTION: THIS MODEL IS DESIGNED TO USE WITH THE FLLOWING AC ADAPTER MODEL ONLY
Manufacturer: LITE -ON ELECTRONICS, INC
Model: PA-1650-01 (65W)

Telephone lines requirement

n The appropriate utilization of 26AWG telephone line cord on unit.
CAUTION: Always disconnect all telephone lines from the wall outlet before servicing or disassembling this equipment.
CAUTION: To reduce the risk of fire, use only No. 26AWG or larger telecommunication line cord.

Battery Pack Safety

n The battery pack is intended to use only with this notebook.
n Do not disassemble the pack.
n Do not dispose of the battery pack in fire or water.

B-3

¦ appendix B agency regulatory notices

n To avoid risk of fire, burns, or damage to your battery pack, do not allow a metal object to touch the battery contacts.
n Handle a damaged or leaking battery with extreme care. If you come in contact with the electrolyte, wash the

exposed area with soap and water. If it contacts the eye, flush the eye with water for 15 minutes and seek medical
attention.

n Do not charge the battery pack if the ambient temperature exceeds 45? (113? ).
n To obtain a replacement battery, contact your local dealer.
n Do not expose the battery pack to high storage temperatures (above 60? , 140? ).
n When discarding a battery pack, contact your local waste disposal provider regarding local restrictions on the disposal

or recycling of batteries.

n Use only supplied AC Adapter for charging.
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended

by the manufacturer. Discard used batteries according to the manufacturer’s instructions or local laws.

VORSICHT! Explisionsgefahr bei unsachgernazen Austausch der Batterie. Ersatz nur durch denselben oder einem vom
Hersteller empfohlenem ahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des Herstellers.

Laser Safety

The optical drive used with this computer is certified as a Class 1 laser device according to the U.S. Department of Health
and Human Services (DHHS) Radiation Performance Standard and International Standards IEC 825 / IEC 825-1 (EN60825
/ EN60825-1). The device is not considered harmful, but the following precautions are recommended:

n Do not open the unit.
n Avoid direct exposure to the laser beam.
n If the unit requires service, contact an authorized service center.
n Ensure proper use by reading and following the instructions carefully.
n Do not attempt to make any adjustment of the unit.

CLASS 1 LASER PRODUCT
APPAREIL A LASER DE CLASSE 1
LASERSCHUTZKLASSE 1 PRODUKT

Warning!

Do not attempt to disassemble the cabinet containing the laser. The laser beam used in this product is harmful to the eyes.
The use of optical instruments, such as magnifying lenses, with this product increase the potential hazard to your eyes. For
your safety, have this equipment serviced only by an authorized service provider.

Lithium battery warning / Bridge battery warning

This computer contains a lithium battery to power the clock and calendar circuitry.
CAUTION: Danger of explosion if battery is replaced incorrectly. Replace only with the same or equivalent type

recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions.
ATTENTION: Il y a danger d’xplosion s’il y a remplacement incorrect de la batterie. Remplacer uniquement avcc unc

batterie du meme type ou d’un type recommande par le constructer. Mettre au rebut les batteries usagees conformement
aux instructions du fabricant.

VORSICHT! Explosionsgefahr bei unsachgemBen Austausch der Batterie Ersatz nur durch denselben oder einem vom
Hersteller empfohlenem ahnlichen Typ. Entsorgung gebrauchter Batterien nach Angaben des Herstellers.

Der Arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 betragt 70dB (A) oder weniger.
Zum Netzanschlua dieses Gerates ist eine geprufte Leitung zu verwenden. Fur einen Nennstrom bis 6A und einem

Gerategewicht groBer 3kg ist eine Leitung nicht leichter als (1)H05VV-F, 3G, 0.75mm2 (2)2X0.75 mm

2

conductors

einzusetzen.

Die Steckdose muB nahe dem Gerat angebracht und leicht zuganglich sein.

B-4

¦ appendix B agency regulatory notices

CAUTION!
This part is hot. Be Careful.
VORSICHT!
Diese Flache wird sehr heiss.

When you see this symbol, be careful as this spot may be very hot.

B-5

Rev 06/07/04

1-YEAR LIMITED WARRANTY

Applicable to new AVERATEC Notebooks

The limited warranty set forth in this warranty
card is provided by AVERATEC, Inc. with
respect to the AVERATEC brand notebook
computer. (Herein referred to as “Portable
Computer”) This warranty is valid for Averatec
Portable Computers purchased and used in the
United States and Canada. The Portable
Computer purchased is the only AVERATEC
brand computer to which this warranty card and
the limited warranty stated herein apply.
When purchased in new condition, your Portable
Computer is warranted against defects for one
(1) year from the date of purchase, with the
exception of the notebook battery. A six (6)
month limited warranty is provided for the
notebook battery. The warranty period cannot be
extended or altered for time the product is
returned for warranty repair.
A defective Portable Computer or a defective
part returned to AVERATEC, proven defective
through testing upon receipt, will be repaired or
exchanged for comparable parts or a
comparable Portable Computer and configured
to the original specifications.
KEEP A COPY OF YOUR ORIGINAL STORE
RECIEPT. Warranty service will only be provided
upon proof of purchase.
This limited warranty shall only apply if the
Portable Computer is used in conjunction with
compatible peripheral equipment and compatible
software. This limited warranty covers all defects
encountered in normal use of the Portable
Computer, and does not apply in the following
cases:
(1) Loss of or damage to, or inability to use, the

Portable Computer in whole or in part due to
abuse, mishandling, improper packaging by
the consumer, alteration, accident, electrical
current fluctuations, software bugs or
viruses, failure to follow operating,
maintenance or environmental instructions
prescribed in AVERATEC’S user’s manual,
or service performed by other than
AVERATEC.

(2) Defects resulting from software, interfacing,

parts or supplies not supplied by
AVERATEC which cause damage to the
Portable Computer or cause abnormally
frequent service calls or service problems.

(3) The Portable Computer has had its serial

number or dating altered or removed.

Additional Information Available at:

PHONE: [phone]
WEB: www.averatec.com

NO IMPLIED WARRANTY, INCLUDING ANY
IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE, APPLIES TO THE
PORTABLE COMPUTER AFTER THE
APPLICABLE PERIOD OF THE EXPRESS
LIMITED WARRANTY STATED ABOVE. NO
OTHER EXPRESS WARRANTY OR
GUARANTY, EXCEPT AS MENTIONED
ABOVE, GIVEN BY ANY PERSON OR ENTITY
WITH RESPECT TO THE PORTABLE
COMPUTER SHALL BIND AVERATEC.
AVERATEC SHALL NOT BE LIABLE FOR
LOSS OF REVENUES OR PROFITS,
EXPENSES FOR SUBSTITUTE EQUIPMENT
OR SERVICE, STORAGE CHARGES, LOSS
OR MISUSE OF, OR INABILITY TO USE THE
PORTABLE COMPUTER, REGARDLESS OF
THE LEGAL THEORY ON WHICH THE CLAIM
IS BASED, INCLUDING IF AVERATEC HAS
BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. AVERATEC IS NEITHER
RESPONSIBLE NOR LIABLE IN ANY WAY
FOR ANY PERSONAL DATA ON THE
PERSONAL COMPUTER, OR FOR LOSS
THEREOF, AND WILL NOT ASSIST IN
BACKUP OR DATA RECOVERY. IN NO
EVENT SHALL DATA RECOVERY OF ANY
KIND AGAINST AVERATEC BE GREATER IN
AMOUNT THAN THE PURCHASE PRICE OF
THE PORTABLE COMPUTER SOLD BY
AVERATEC AND CAUSING THE ALLEGED
DAMAGE. WITHOUT LIMITING THE
FOREGOING, CONSUMER ASSUMES ALL
RISKS AND LIABILITY FOR LOSS, DAMAGE,
OR INJURY TO ONESELF OR THEIR
PROPERTY, OR TO OTHERS AND THEIR
PROPERTY ARISING OUT OF THE USE OR
MISUSE OF, OR INABILITY TO USE, THE
PORTABLE COMPUTER. THIS LIMITED
WARRANTY SHALL NOT EXTEND TO
ANYONE OTHER THAN THE ORIGINAL
PURCHASER OF THE PORTABLE
COMPUTER, OR THE PERSON FOR WHOM
IT WAS PURCHASED AS A GIFT, AND
STATES EXCLUSIVE REMEDY.

This limited warranty gives you specific legal
rights, and you may also have other rights, which
vary, from state to state.

Rev 03/15/05

SIX MONTH LIMITED WARRANTY

Applicable to new AVERATEC Batteries

The limited warranty set forth on this warranty card is provided by AVERATEC, Inc. with respect to the AVERATEC
brand Battery that you have purchased, when purchased and used with a AVERATEC brand notebook computer.
The Battery that you have purchased is the only AVERATEC brand product to which this warranty card and the
limited warranty stated herein apply.

Your Battery, when purchased in a new condition, is warranted against defects for six (6) months from the date of
purchase. The warranty period will not be extended or altered for any time for any time during which it is in for
warranty repair.

A defective Battery returned to AVERATEC and proven to be defective upon inspection will be repaired or exchanged
for a comparable part.

KEEP A COPY OF YOUR ORIGINAL STORE RECIEPT. Warranty service will only be provided upon proof of
purchase provided to AVERATEC.

This limited warranty shall only apply if the Battery is used in conjunction with compatible peripheral equipment and
compatible software. This limited warranty covers all defects encountered in normal use of the Accessory, and does
not apply in the following cases:

(1) Loss of or damage to, or inability to use, the Battery in whole or in part due to abuse, mishandling, improper

packaging by you, alteration, accident, electrical current fluctuations, software bugs or viruses, failure to
follow operating, maintenance or environmental instructions prescribed in AVERATEC’S user’s manual, or
service performed by other than AVERATEC.

(2) Defects resulting from software, interfacing, parts or supplies not supplied by AVERATEC which cause

damage to the Battery or cause abnormally frequent service calls or service problems.

(3) If the Battery has had its serial number or dating altered or removed.

NO IMPLIED WARRANTY, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE, APPLIES TO THE BATTERY AFTER THE APPLICABLE PERIOD OF THE
EXPRESS LIMITED WARRANTY STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY,
EXCEPT AS MENTIONED ABOVE, GIVEN BY ANY PERSON OR ENTITY WITH RESPECT TO THE BATTERY
SHALL BIND AVERATEC. AVERATEC SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR PROFITS,
EXPENSES FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OR MISUSE OF, OR
INABILITY TO USE, THE BATTERY, REGARDLESS OF THE LEGAL THEORY ON WHICH THE CLAIM IS
BASED, AND EVEN IF AVERATEC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO
EVENT SHALL RECOVERY OF ANY KIND AGAINST AVERATEC BE GREATER IN AMOUNT THAN THE
PURCHASE PRICE OF THE BATTERY SOLD BY AVERATEC AND CAUSING THE ALLEGED DAMAGE.
WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE, OR
INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE OR
MISUSE OF, OR INABILITY TO USE, THE BATTERY NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF
AVERATEC. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL
PURCHASER OF THE BATTERY, OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT, AND
STATES YOUR EXCLUSIVE REMEDY.

This limited warranty gives you specific legal rights, and you may also have other rights, which vary, from state to
state.

Additional Information Available at:

PHONE: [phone]

WEB: www.averatec.com

Rev 03/15/05

1-YEAR LIMITED WARRANTY

Applicable to new AVERATEC Accessories

The limited warranty set forth on this warranty card is provided by AVERATEC, Inc. with respect to the AVERATEC
brand Accessory that you have purchased, when purchased and used with a AVERATEC brand notebook computer.
The accessory that you have purchased is the only AVERATEC brand product to which this warranty card and the
limited warranty stated herein apply.

Your Accessory, when purchased in a new condition, is warranted against defects for one (1) year from the date of
purchase. The warranty period will not be extended or altered for any time for any time during which it is in for
warranty repair.

A defective Accessory returned to AVERATEC and proven to be defective upon inspection will be repaired or
exchanged for comparable part.

KEEP A COPY OF YOUR ORIGINAL STORE RECIEPT. Warranty service will only be provided upon proof of
purchase provided to AVERATEC.

This limited warranty shall only apply if the Accessory is used in conjunction with compatible peripheral equipment
and compatible software. This limited warranty covers all defects encountered in normal use of the Accessory, and
does not apply in the following cases:

(1) Loss of or damage to, or inability to use, the Accessory in whole or in part due to abuse, mishandling,

improper packaging by you, alteration, accident, electrical current fluctuations, software bugs or viruses,
failure to follow operating, maintenance or environmental instructions prescribed in AVERATEC’S user’s
manual, or service performed by other than AVERATEC.

(2) Defects resulting from software, interfacing, parts or supplies not supplied by AVERATEC which cause

damage to the Accessory or cause abnormally frequent service calls or service problems.

(3) If the Accessory has had its serial number or dating altered or removed.

NO IMPLIED WARRANTY, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR
A PARTICULAR PURPOSE, APPLIES TO THE ACCESSORY AFTER THE APPLICABLE PERIOD OF THE
EXPRESS LIMITED WARRANTY STATED ABOVE, AND NO OTHER EXPRESS WARRANTY OR GUARANTY,
EXCEPT AS MENTIONED ABOVE, GIVEN BY ANY PERSON OR ENTITY WITH RESPECT TO THE
ACCESSORY SHALL BIND AVERATEC. AVERATEC SHALL NOT BE LIABLE FOR LOSS OF REVENUES OR
PROFITS, EXPENSES FOR SUBSTITUTE EQUIPMENT OR SERVICE, STORAGE CHARGES, LOSS OR MISUSE
OF, OR INABILITY TO USE, THE ACCESSORY, REGARDLESS OF THE LEGAL THEORY ON WHICH THE
CLAIM IS BASED, AND EVEN IF AVERATEC HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
IN NO EVENT SHALL RECOVERY OF ANY KIND AGAINST AVERATEC BE GREATER IN AMOUNT THAN THE
PURCHASE PRICE OF THE ACCESSORY SOLD BY AVERATEC AND CAUSING THE ALLEGED DAMAGE.
WITHOUT LIMITING THE FOREGOING, YOU ASSUME ALL RISK AND LIABILITY FOR LOSS, DAMAGE, OR
INJURY TO YOU AND YOUR PROPERTY AND TO OTHERS AND THEIR PROPERTY ARISING OUT OF USE OR
MISUSE OF, OR INABILITY TO USE, THE ACCESSORY NOT CAUSED DIRECTLY BY THE NEGLIGENCE OF
AVERATEC. THIS LIMITED WARRANTY SHALL NOT EXTEND TO ANYONE OTHER THAN THE ORIGINAL
PURCHASER OF THE ACCESSORY, OR THE PERSON FOR WHOM IT WAS PURCHASED AS A GIFT, AND
STATES YOUR EXCLUSIVE REMEDY.

This limited warranty gives you specific legal rights, and you may also have other rights, which vary, from state to
state.

Additional Information Available at:

PHONE: [phone]

WEB: www.averatec.com