Page 1
www.avenview.com
1
Wireless 5G HDMI Transmitter & Receiver
With 1080p and 3D compatible
Model #: W-HDM3D5G-30M
© 3012 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or warranties with
respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product deLCriptions at any
time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in
Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and diLClaims any express or implied warranty, relating to its
products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
Reproduction of this manual, or parts thereof, in any form, without the express written permission of Avenview Inc. is strictly prohibited.
Page 2
www.avenview.com
2
Table of Contents
Section 1: Getting Started ...................................................................................................................... 3
1.1 Important Safeguards ............................................................................................................ 3
1.2 Safety Instructions ................................................................................................................. 3
1.3 Regulatory Notices Federal Communications Commission (FCC) ......................................... 4
1.4 Introduction ........................................................................................................................... 4
1.5 Package Contents ................................................................................................................... 4
1.6 Before Installation.................................................................................................................. 4
1.7 Device Description & Layout .................................................................................................. 5
1.8 Getting Started....................................................................................................................... 7
1.9 A. Standard Package Installation ........................................................................................... 8
1.10 C. Full Package Installation .................................................................................................... 9
1.11 D. Standard Package Installation ......................................................................................... 10
1.12 Operation ............................................................................................................................. 10
1.13 Remote Control Functions ................................................................................................... 11
1.14 Add or Delete Transmitter ................................................................................................... 12
Section 2: Specifications ....................................................................................................................... 14
Page 3
www.avenview.com
3
Section 1: Getting Started
1.1 Important Safeguards
Please read all of these instructions carefully before you use the device. Save this manual for future
reference.
What the warranty does not cover
Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, or failure to follow instructions supplied with the product.
Repair or attempted repair by anyone not authorized by us.
Any damage of the product due to shipment.
Removal or installation of the product.
Causes external to the product, such as electric power fluctuation or failure.
Use of supplies or parts not meeting our specifications.
Normal wear and tear.
Any other causes which does not relate to a product defect.
Removal, installation, and set-up service charges.
1.2 Safety Instructions
The Avenview W-HDM5G-30M, Wireless Extender has been tested for conformity to safety regulations and
requirements, and has been certified for international use. However, like all electronic equipment’s, the
W-HDM5G-30M should be used with care. Read the following safety instructions to protect yourself from
possible injury and to minimize the risk of damage to the unit.
Do not dismantle the housing or modify the module.
Dismantling the housing or modifying the module may result in electrical shock or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing housing may expose you to
dangerous voltage or other hazards
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid
falls or spills on to the housing, unplug the module immediately.
Have the module checked by a qualified service engineer before using it again.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
cleaning.
Do not view directly into the laser module of transmitter or the end of the other side of optical cable
connected to transmitter with an optical instrument.
Page 4
www.avenview.com
4
1.3 Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this
equipment.
1.4 Introduction
W-HDM5G-30M, wireless extender set runs at 5GHz operation frequency to deliver uncompressed HD
video/audio 30 meters in open field. This device kit make wireless connection by using WHDI Technology from
HD media Source Devices such as HD Disc player, PC, Game Console, Set-to –Box to any display Device for
example LCD Plasma or LED TV and projector while keeping wire –equivalent quality and no latency.
WHDI Technology no latency
Extends HDMI or DVI signals up to 30M (open Space) or 12M (indoor)”
Supports HDMI 1.4, EDID 1.1, Support HDCP 2.0
Supports resolution up to 3D supported HDTV / 1080Pp/60Hz, Vesa (1920 x 1080)
Real time compression audio is embedded within the HDMI output stream
Suitable for use with Home Cinema and Computer Equipment
Extends IR and CEC Signals for remote control of AV Equipment
Supporting the point to point transmission function currently which can be expanded to the
multi-point to point transmission function.
1.5 Package Contents
Before you start the installation of W-HDM5G-30M, please check the A. STANDARD package contents.
- Wireless Transmitter x 1
- Wireless Receiver x 1
- Power Adapter (5VDC) x 2
- Remote Control x 1
- User Manual x 1
- IR Extension Cable
1.6 Before Installation
Put the product in an even and stable location. If the product falls down or drops, it may cause an
injury or malfunction.
Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high
humidity.
Use the DC power adapter with correct specifications. If inappropriate power supply is used then it
may cause a fire.
Page 5
www.avenview.com
5
1.7 Device Description & Layout
Actual Distances will depend entirely on the construction of the building and any walls or floors
that are situated between the Transmitter and Receiver Units
This product is composed of a Transmitter and a Receiver.
Page 6
www.avenview.com
6
A. Standard Package
B. Standard + HDMI Switch
1 x Wireless HDMI Transmitter
1 x Wireless HDMI Receiver
1 x Remote Control
2 x DC 5V Power Adapter
1 x IR Extension Cable
1 x HDMI Cable
1 x User Guide
1 x Wireless HDMI Transmitter
1 x Wireless HDMI Receiver
1 x Remote Control
2 x DC 5V Power Adapter
1 x IR Extension Cable
1 x HDMI Cable
1 x HDMI Switch
1 x User Guide
C. Full Package (HDMI Switch +IR Extension
D. Stick Transmitter + Receiver
1 x Wireless HDMI Transmitter
1 x Wireless HDMI Receiver
1 x Remote Control
2 x DC 5V Power Adapter
1 x IR Extension Cable (4 x IR Eye)
1 x HDMI Cable
1 x HDMI Switch
1 x User Guide
1 x Wireless HDMI Transmitter Stick
1 x Wireless HDMI Receiver
1 x Remote Control
2 x DC 5V Power Adapter
1 x IR Extension Cable
1 x HDMI Cable
1 x HDMI Converter
1 x USB Cable
1 x User Guide
Page 7
www.avenview.com
7
1.8 Getting Started
Each Transmitter and Receiver after pairing support only point to point operation. It cannot
support signals broadcasting by wireless.
Important Before starting the insulation please ensure that all devices are powered OFF
It is ideal when your media player is located in your living room, while you want to watch your Full HD Movies
on Your LCD, Plasma or LED display device in your bedroom. You can install the Wireless HD Transmitter and
Receiver Kit and let the wireless transmission do the work via the air. Furthermore, you can operate the media
player with the original remote control in your bedroom.
The Wireless Extender can be used horizontal or vertical mode, depending on your requirement; however for
optimum performance is it recommended to operate in vertical mode. To use the extender in vertical mode
simply slide the foot, on the bottom edge of each unit until it creates a 90 ˚ angle with the body of the unit.
Page 8
www.avenview.com
8
1.9 A. Standard Package Installation
1. Place the Transmitter unit in close proximity to the HDMI source device.
2. Connect the HDMI source device to HDMI IN port of the Transmitter by using a standard HDMI cable.
3. Connect the IR Extension cable to the port on the transmitter unit.
4. Place the other end of the IR Extension cable near the IR port on the HDMI source device.
5. Place the Receiver unit near your HDMI display/projector, Connect the HDMI display /projector to the
HDMI Output port of the Receiver unit 5.
6. Connect the power adapter (included) to the DC IN ports of the Transmitter and Receiver.
Once these steps have been completed the Extender is ready to use, simply power on all devices to begin
operation.
Page 9
www.avenview.com
9
1.10 C. Full Package Installation
1. Place the Transmitter unit in close proximity to the HDMI source device.
2. Connect the HDMI Switch to the Transmitter
3. Connect the HDMI source device to HDMI IN port of the Transmitter by using a standard HDMI cable.
4. Connect the IR Extension cable to the IR port on the HDMI Switch.
5. Place the other end of the IR Extension cable near the IR port on the HDMI source device.
6. Place the Receiver unit near the HDMI display/projector, Connect the HDMI display /projector to the
HDMI Output port of the Receiver unit 5.
7. Connect the power adapter (included) to the DC IN ports of the Transmitter and Receiver.
Once these steps have been completed the Extender is ready to use, simply power on all devices to begin
operation.
Page 10
www.avenview.com
10
1.11 D. Standard Package Installation
1. Place the Stick Transmitter unit in close proximity to the HDMI source device.
2. Connect the HDMI source device to HDMI IN port of the Transmitter by using a standard HDMI cable.
3. Place the Receiver unit near your HDMI display/projector, Connect the HDMI display /projector to the
HDMI Output port of the Receiver unit 5.
4. Connect the power adapter (included) to the DC IN ports of the Transmitter and Receiver.
Once these steps have been completed the Extender is ready to use, simply power on all devices to begin
operation.
1.12 Operation
Once all equipment is turned on, the Extender will initiate a Wireless link successful connection of the link will
be shown by the blue Wireless Link LED on Both the Transmitter and Receiver. Once this has been completed
the blue Link Led will be lit on both units.
Whilst the Extender is creating the video link it is normal for the HDMI display to flicker ON and OFF. With
both the wireless and video Link LED illuminated the Extender is ready to transmit video. If your HDMI source
and display devices support CEC then the source device can simply be controlled using the display remote
control.
IR Extender Function
If the HDMI source and display devices support CEC, then it is possible to control the source device remotely
using the IR Extender function. Ensure that the IR Eye on the Receiver unit is positioned to receive IR
Commands.
1. Connect the supplied IR Extender Cable to the IR Input on the Transmitter unit
2. Position the IR Flasher near the IR Port of the source device
Page 11
www.avenview.com
11
1.13 Remote Control Functions
Button
Description
MENU
Enter Setup Mode
EXIT
Exit Setup Mode
SOURCE
Wireless Transmitter List
ADD
Searching and adding a new Wireless Transmitter
DELETE
Delete a Wireless Transmitter
OK
Enter or Confirm Function
SHIFT
Transmitter name character editing
A1- A4
Switch 4 Video Source for Local HDMI Display
B1 – B4
Switch 4 Video Source for Wireless HDMI Transmitter
GUEST
User HOT Key ,
Default as Sleep Mode function with HDMI Switch (B and C Package)
Character Selection
Page 12
www.avenview.com
12
1.14 Add or Delete Transmitter
1. Use the supplied remote control to search and add a new transmitter or delete a Transmitter.
2. First turn on your Wireless HDMI Transmitter and Receiver, Remote control point to Transmitter.
3. Press the remote control MENU button, HDMI Display show.
Page 13
www.avenview.com
13
General Troubleshooting
Problem
Possible Solution
The Wireless or Video
Link LED is not Lit
If the transmitter and /or Receiver are positioned horizontally
move the units to vertical position. Power cycle both extender
units (OFF 30 sec then ON).
Reduce the distance between the Transmitter and Receiver
units. Power cycle both extender units (OFF 30 sec then ON).
The screen is blank
Re-check all connections and verify they are in the correct
positions and verify the units are powered.
Check that the wireless and Video Link LEDs are LIT
The IR Extender does not work
Check the IR Extender cable is connected to the Transmitter
unit
Check that the IR EYE is visible and not being obstructed and
the transmission of IR from the remote can be sent.
Reposition the IR Flasher to another location near the IR port of
your source device
What is Consumer Electronics Control (CEC)?
Consumer Electronics Control or CEC is a function that allows you to control multiple devices over
HDMI using one remote control by having a secondary device receives commands from a
primary device.
Although CEC wiring is required for every HDMI port it does not mean that every HDMI port will
have the function enabled. If your device has the CEC function, this information will be located
under your setup or settings menu. To enable the function you will need to turn the CEC function
on and then search for any devices that are CEC enabled that are connected to the TV.
Page 14
www.avenview.com
14
Section 2: Specifications
Item
Description
Units
W-HDM3D5G-S-30M (Transmitter)
W-HDM3D5G-R-30M (Receiver)
Unit Description
WIRELESS Transmitter
WIRELESS Receiver
Operating Frequency
5.1GHz to 5.9 GHz
5.1GHz to 5.9 GHz
RF Communication
MIMO
MIMO
Audio Format
Supported
PCM,DTS,DOLBY DIGITAL
Supported Resolution &
Distance
TV-Up to 480P,576P,720P,1080i1080p60Hz @ 30 meters (66 feet)
PC Up to 1920x1080 Pixels
HDMI Connector
HDMI FEMALE Plug (input)
HDMI FEMALE Plug (input)
Antenna
High Performance Internal Antenna
Image Delay
<1ms
IR CMFS
38KHz
Modulation
OFDM
Transmission Power
12dBm+- 2dBm
Dimensions (L x W x H)
11.5” x 1.3” x .5”
Power Supply
AC Input 100-240V,DC Output 5V
Environmental
Operating Temperature
32˚ ~ 104˚F (0˚ to 40˚C)
Storage Temperature
-4˚ ~ 140˚F (-20˚ ~ 60˚C)
Relative Humidity
20~90% RH (no condensation)
Page 15
www.avenview.com
15
DiLClaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the
operation or use of Avenview hardware, software or other products and documentation described herein, for any act or omission of
Avenview concerning such products or this documentation, for any interruption of service, loss or interruption of business, loss of
anticipatory profits, or for punitive, incidental or consequential damages in connection with the furnishing, performance, or use of the
Avenview hardware, software, or other products and documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability,
function or design. With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties
regarding such products, including but not limited to, the implied warranties of merchantability, fitness for a particular purpose, and
non-infringement.
Loading...