Page 1
www.avenview.com
1
Remote Screen/Print Sharing Extender over
WIFI / LAN with KVM
Model #: HDM-SHAREPRO-IP
© 2012 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) product s. Avenview makes no representations or warranties with
respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications and product deLCriptions at any
time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted by this publication. Except as set forth in
Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and di LClaims any express or implied warranty, relating to its
products including, but not limited to, the implied warranty of merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
Reproduction of this manual, or parts thereof, in any form, without the express written permission of Avenview Inc. is strictly prohibited.
Page 2
www.avenview.com
2
Table of Contents
Section 1: Getting Started ...................................................................................................................... 3
1.1 Important Safeguards ............................................................................................................ 3
1.2 Safety Instructions ................................................................................................................. 3
1.3 Regulatory Notices Federal Communications Commission (FCC) ......................................... 4
1.4 Introduction ........................................................................................................................... 4
1.5 Package Contents ................................................................................................................... 4
1.6 Before Installation.................................................................................................................. 5
1.7 Device Description & Layout .................................................................................................. 5
1.8 Installation A .......................................................................................................................... 6
1.9 Installation B .......................................................................................................................... 7
1.10 Installation of Driver and Control Software. .......................................................................... 8
1.11 Control Software .................................................................................................................... 9
1.12 Disconnect Software ............................................................................................................ 10
Section 3: General Troubleshooting..................................................................................................... 11
Section 4: Specifications ....................................................................................................................... 12
4.1 PIN & Wiring Standard Definition ........................................................................................ 13
Page 3
www.avenview.com
3
Section 1: Getting Started
1.1 Important Safeguards
Please read all of these instructions carefully before you use the device. Save this manual for future
reference.
What the warranty does not cover
Any product, on which the serial number has been defaced, modified or removed.
Damage, deterioration or malfunction resulting from:
Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, or failure to follow instructions supplied with the product.
Repair or attempted repair by anyone not authorized by us.
Any damage of the product due to shipment.
Removal or installation of the product.
Causes external to the product, such as electric power fluctuation or failure.
Use of supplies or parts not meeting our specifications.
Normal wear and tear.
Any other causes which does not relate to a product defect.
Removal, installation, and set-up service charges.
1.2 Safety Instructions
The Avenview HDM-SHAREPRO-IP, RJ45 to HDMI Converter has been tested for conformity to safety
regulations and requirements, and has been certified for international use. However, like all electronic
equipment’s, the HDM-SHAREPRO-IP should be used with care. Read the following safety instructions to
protect yourself from possible injury and to minimize the risk of damage to the unit.
Do not dismantle the housing or modify the module.
Dismantling the housing or modifying the module may result in electrical shock or burn.
Refer all servicing to qualified service personnel.
Do not attempt to service this product yourself as opening or removing housing may expose you to
dangerous voltage or other hazards
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid
falls or spills on to the housing, unplug the module immediately.
Have the module checked by a qualified service engineer before using it again.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before
cleaning.
Page 4
www.avenview.com
4
1.3 Regulatory Notices Federal Communications Commission (FCC)
This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this
equipment.
1.4 Introduction
HDM-SHAREPRO-IP is an ideal networking display solution; it allows multiple users on the same Ethernet
network to access the display without physically connect their computer directly to the display! The product
supports ONLY ONE connection at a time. Users can now enjoy their favorite multimedia content stored on
their computer from anywhere in their home or office. HDM-SHAREPRO-IP also act as a display extender that
supports up to 1920*1080 resolutions with primary display, mirror desktop and extended desktop video
modes!
Support 1080p Video over TCP/IP,LPR,DHCP,UPnP
Support USB Keyboard and Mouse Wired/Wireless
Supports 500mA electric current for every USB port;
Digital Video HDMI with Audio
Analog Video with VGA and Audio connection
Analog 3.5mm Audio out connection
Converts RJ45 to HDMI
Ethernet IEEE 802 3 10Base IEEE
Standards:802.3 10Base-T;802.3U 100Base-T
Network Interface:10/100/1000Mbps RJ45
Supports the resolution up to 1080p
Allows multiple users to share a Multi-Function Print (MFP) over a network to print, scan, and fax
from any networked computer;
Supports Windows 7,Vista and XP
1.5 Package Contents
Before you start the installation of HDM-SHAREPRO-IP, please check the STANDARD package contents.
- HDM-SHAREPRO-IP x 1
- Power Adapter (5VDC) x 1
- User Manual x 1
- Installation Disc x 1
Page 5
www.avenview.com
5
1.6 Before Installation
1. +5V DC: Connect to 5V DC power supply
3. USB INPUT: Connect ANY mouse/keyboard
wired/wireless adapter.
2. CAT/6: Plug in a CAT6 cable that is connected to
your router on the same IP Network
4. 3.5mm Jack: Stereo audio INPUT connection for
VGA connection.
5. 3.5mm Jack: Stereo audio OUTPUT connection for
VGA connection.
6. VGA: Connects to VGA Monitor with a male-male
cable.
7. HDMI OUT: Connects to a HDMI monitor with a
HDMI male-male cable
Note: Preferred CAT6 and Gigabit 10/1000 Router to ensure HD1080p resolution without delay in
transmission
Important Before starting the insulation please ensure that all devices are powered OFF
1
2
3
Put the product in an even and stable location. If the product falls down or drops, it may cause an
injury or malfunction.
Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high
humidity.
Use the DC power adapter with correct specifications. If inappropriate power supply is used then it
may cause a fire.
1.7 Device Description & Layout
This product is composed of a Converter RJ45 to HDMI
FRONT PANEL & REAR PANEL (Transmitter, HDM-C6IP-S)
Page 6
www.avenview.com
6
1.8 Installation A
DIRECT CONNECTION
HDMI CABLE
CAT5E/6
COMPUTER
Please ensure all the package contents are all received.
To setup Avenview HDM-SHAREPRO-IP follow these steps for connecting directly to a Monitor as a
CONVERTER:
1. Connect Converter to CPU with RJ45 cable; follow the standards of TIA-568BLAN
2. Connect your HDMI OR VGA display (such as a LCD TV/PLASMA) to the HDMI OR VGA Port on the
HDM-SHAREPRO-IP.
3. Make sure CAT-5E/6 LAN cable is tightly connected and not loose.
5. Plug in 5V DC power cord to the power jack of the transmitting unit HDM-SHAREPRO-IP.
Page 7
www.avenview.com
7
BOARDROOM (IP10.0.1.105)
LAPTOP WIRELESS @ OFFICE 1 (IP10.0.1.107)
CPU WIRED @ OFFICE 2 (IP10.0.1.106)
1.9 Installation B
Please ensure all the package contents are all received.
To setup Avenview HDM-SHAREPRO-IP follow these steps for connecting to a Remote Monitor.
1. Connect HDM-SHAREPRO-IP to Wireless or Wired Router with RJ45 cable at the desired Monitor; follow
the standards of TIA-568BLAN
2. Connect your HDMI OR VGA display (such as a LCD TV/PLASMA) to the HDMI OR VGA Port on the
HDM-SHAREPRO-IP.
3. Make sure CAT-5E/6 LAN cable is tightly connected and not loose.
5. Plug in 5V DC power cord to the power jack of the transmitting unit HDM-SHAREPRO-IP.
BOTH OFFICES CAN USE THIS PRODUCT ONCE THE SOFTWAR IS INSTALLED (NB: One at a Time)
ROUTER CONNECTION
Page 8
www.avenview.com
8
You will experience brief periods of dark screens and /or resolution changes during this time.
1.10 Installation of Driver and Control Software.
Insert Disk and run the Driver.exe file
Select your preferred Language.
From Disk run the Software.exe file
Accept and wait for install to be completed automatically
When completed restart the computer.
Page 9
www.avenview.com
9
Either or Both Selected
1.11 Control Software
Step 1.
Double-click ICON USB Server file:
On first use, click search and then the software will search the HDM-SHAREPRO-IP automatically.
System will display video converter searched out
Click : (The preferred device to be connected-DISPLAY or MEDIA DEVICE)
Click B: (connect the device), the converter will be automatically connected.
Note :( The system will set up the driver automatically for the first connection) connect the required one by one.
Note :( It is normal if the display is black for seconds in this process.)
Step 2.
Open Control Panel/Display/Screen Resolution, the HDMI output resolution can be set.
Page 10
www.avenview.com
10
Take Windows 7 as example:
Short-cut function cannot be applied by some computers due to compatibility
A. Select the display that needs to adapt. 1 Display is input computer and 2 Display is output device by default.
B. Set up the resolution
C. Set up the display direction
D. Set up the display mode
Note: Short-cut Function: Press”Win+P” to see the following images.
From left to right, Computer only, Duplicate, Extend and Projector only. You can easily switch display mode.
From left to right, Computer only, Duplicate, Extend and Projector only. You can easily switch display mode.
1.12 Disconnect Software
A. Select the device
B. Click the button to disconnect the chose device.
Page 11
www.avenview.com
11
Problem
Possible Solution
No video output
Please make sure that all cables properly connected.
Please disconnect the connectivity in software and re-connect or
re-install the driver.
No Audio or Mouse Response
The connectivity will be always disturbed by unstable network.
Please disconnect the connection of audio and mouse in software.
Display will show “Be sure to
disconnect the device and exit?”
when USB server is closed.
Power off the converter or re-boot the computer.
Connect VGA and HDMI output
simultaneously, but VGA no display
A: Please select VGA or HDMI output before the converter is powered on.
If the software refuses to disconnect, please power off the converter.
Make sure to store all files before power off.
Section 3: General Troubleshooting
Page 12
www.avenview.com
12
Section 4: Specifications
Item
Description
Units
HDM-SHAREPRO-IP
Unit Description
RJ45 TO HDMI CONVERTER
HDMI Compliance
Full HD
HDCP Compliance
Yes
Supported Resolutions
480i@60Hz, 480p@60Hz, 576i@50Hz, 576p@50Hz, 720p@50/60Hz,
1080i@50/60Hz, 1080p@50/60Hz
Audio Support
Stereo Audio
USB Support
Multi-Function Print (MFP) over a network from any networked computer;
USB Support
Wired or Wireless Keyboard Mouse/Supports 500mA electric current 2x USB
Input
1 x 3.5mm Audio ,2 x USB, 1 x RJ45
Output
1x VGA + 3.5mm Stereo Audio
1x HDMI + 1x 3.5mm
HDMI Connector
Type A (19 pin female)
RJ45 Connector
WE/SS 8P8C with 2 LED indicators
Power Adapter
1 X DC 5V/1A
Power Consumption
3W Max Each
Dimension L x W x H
110 x 58 x 26mm (4.3” x 2.2” x 1”)
Weight
245g
Environmental
Operating Temperature
32˚ ~ 104˚F (0˚ to 40˚C)
Storage Temperature
-4˚ ~ 140˚F (-20˚ ~ 60˚C)
Relative Humidity
20~90% RH (no condensation)
Performance rating
Type of category cable
Wiring
Shielding
CAT5
CAT5e
CAT6
Solid
Unshielded (UTP)
Shielded (STP)
Stranded
Unshielded (UTP)
Shielded (STP)
Termination
Please use EIA/TIA-568-B termination (T568B) at any time
Performance Guide for HDMI over Category Cable Transmission
Page 13
www.avenview.com
13
4.1 PIN & Wiring Standard Definition
Pin 1
TMDS Data2+
Pin 11
TMDS Clock Shield
Pin 2
TMDS Data2 Shield
Pin 12
TMDS Clock–
Pin 3
TMDS Data2–
Pin 13
CEC
Pin 4
TMDS Data1+
Pin 14
Reserved (N.C. on device)
Pin 5
TMDS Data1 Shield
Pin 15
SCL
Pin 6
TMDS Data1–
Pin 16
SDA
Pin 7
TMDS Data0+
Pin 17
DDC/CEC Ground
Pin 8
TMDS Data0 Shield
Pin 18
+5V Power
Pin 9
TMDS Data0–
Pin 19
Hot Plug Detect
Pin 10
TMDS Clock+
Type A (Receptacle) HDMI
Page 14
www.avenview.com
14
Disclaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the
operation or use of Avenview hardware, software or other products and documentation described herein, for any act or omission of
Avenview concerning such products or this documentation, for any interruption of service, loss or interruption of business, loss of
anticipatory profits, or for punitive, incidental or consequential damages in connection with the furnishing, performance, or use of the
Avenview hardware, software, or other products and documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability,
function or design. With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties
regarding such products, including but not limited to, the implied warranties of merchantability, fitness for a particular purpose, and
non-infringement.
Loading...