Avenview HDM3D-C5SP-4 User Manual

VIDEO WALLS VIDEO PROCESSORS

VIDEO MATRIX SWITCHES

EXTENDERS SPLITTERS WIRELESS

AV Connectivity, Distribution And Beyond...

1x4 HDMI Extender / Splitter

Single CAT5 with 3D Support and

Local Output

CABLES & ACCESSORIES

© 2013 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and disclaims
any express or implied warranty, relating to its products of Avenview Inc. is strictly prohibited.

Model #: HDM3D-C5SP-4

Product Application & Market Sectors

Corporate House Of Worship

Military Residential

Education Industrial

Medical Aviation

www.avenview.com

TABLE OF CONTENTS

1. GETTING STARTED ..........................................................................................................................1

1.1 IMPORTANT SAFEGUARDS .............................................................................................................. 1

1.2 SAFETY INSTRUCTIONS ..................................................................................................................1

1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC) ........................... 2

2. INTRODUCTION .............................................................................................................................. 3

2.1 PACKAGE CONTENTS .....................................................................................................................3

2.2 BEFORE INSTALLATION ...................................................................................................................4

2.3 PANEL DESCRIPTION .......................................................................................................................5

2.3.1 Front Panel .................................................................................................................................5

2.3.2 Rear Panel...................................................................................................................................5

2.3.3 Bottom Panel ..............................................................................................................................5

3. EDID LEARNING ...............................................................................................................................6

4. INSTALLATION ..................................................................................................................................6

5. GENERAL TROUBLESHOOTING ..................................................................................................... 7

5. SPECIFICATIONS ............................................................................................................................... 8

6. HDMI PIN DEFINITION .................................................................................................................... 9

www.avenview.com

Page 3

1. GETTING STARTED

SECTION 1: GETTING STARTED

1.1 IMPORTANT SAFEGUARDS

Please read all of these instructions carefully before you use the device. Save this manual for future reference.

What the warranty does not cover

• Any product, on which the serial number has been defaced, modified or removed.

• Damage, deterioration or malfunction resulting from:

• Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to
follow instructions supplied with the product.

• Repair or attempted repair by anyone not authorized by us.

• Any damage of the product due to shipment.

• Removal or installation of the product.

• Causes external to the product, such as electric power fluctuation or failure.

• Use of supplies or parts not meeting our specifications.

• Normal wear and tear.

• Any other causes which does not relate to a product defect.

• Removal, installation, and set-up service charges.

1.2 SAFETY INSTRUCTIONS

The Avenview HDM3D-C5SP-4 HDMI Extender / Splitter over CAT5 with Full 3D Support has been tested for conformance to
safety regulations and requirements, and has been certified for international use. However, like all electronic equipment’s, the
HDM3D-C5SP-4 should be used with care. Read the following safety instructions to protect yourself from possible injury and to
minimize the risk of damage to the unit.

Do not dismantle the housing or modify the module.

!

Dismantling the housing or modifying the module may result in electrical shock or burn.

!

Refer all servicing to qualified service personnel.

!

Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous voltage

!

or other hazards

Keep the module away from liquids.

!

Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on

!

to the housing, unplug the module immediately.

Have the module checked by a qualified service engineer before using it again.

!

Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.

!

www.avenview.com

Page 1

1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC)

This equipment has been tested and found to comply with Part 15 of the FCC rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation.

Any changes or modifications made to this equipment may void the user’s authority to operate this equipment.

Warning symbols Description

ONLY USE THE PROVIDED POWER CABLE OR POWER

ADAPTER SUPPLIED. DO NOT TAMPER WITH THE

ELECTRICAL PARTS. THIS MAY RESULT IN ELECTRICAL

SHOCK OR BURN.

DO NOT TAMPER WITH THE UNIT. DOING SO WILL

VOID THE WARRANTY AND CONTINUED USE OF THE

PRODUCT.

THE VIDEO BOARDS ARE VERY SENSITIVE TO STATIC.
PLEASE ENSURE IF RACK MOUNTED OR INSTALLED ON A
SURFACE, IT SHOULD BE IN A GROUNDED ENVIROMENT.

www.avenview.com

Page 2

2. INTRODUCTION

The Avenview HDM3D-C5SP-4 HDMI over Single CAT5 with Full 3D Support Distribution Amplifier with Local Output provides
the most flexible solution by which the high definition video and high quality audio can be transmitted to different locations over
a long distance. These devices can cascade, allowing you to extend HDMI compliant displays almost anywhere. The input HDMI
source can be duplicated and distributed to up to 4 HDMI enable displays through cost effective Cat-5/6 cables and RJ-45 to
HDMI mini-extenders HDM3D-C5-R-M or Long Range HDM-C53X-R aka HDM3D-C53X-R. With the built in equalization, the
input HDMI cable can be extended up to 20 meters (66 feet) long under Full HD, and make the overall transmission distance
superior than regular HDMI splitters or matrix switches in the market. With use of Long Range Receiver, HDMI signal can be
extended to 50 meters (165 feet).

- Supports HDMI Deep Color & Full 3D

- HDMI

- HDCP compliant

- Regenerates the HDMI signal

- HDMI local output

- Supports default HDMI EDID and has the ability to learn the EDID of the displays

- Extends up to 20m (66ft) of input HDMI cable with Mini Receiver

- Extends up to 50m (165ft) (720p / 1080i) of output CAT5/6 cable with Long Range Receiver

- Extends up to 40m (130ft) (1080p) of output CAT5/6 cable with Long Range Receiver

- Pure unaltered uncompressed 7.1ch digital HDMI over LAN cable transmission

- Allows cascading

- Perfectly integrated with other HDM-C5XD Series products

2.1 PACKAGE CONTENTS

Before you start the installation of the Extender/Splitter, please check the package contents.

HDM3D-C5SP-4 X 1

1

POWER ADAPTER (+5VDC, 4A) X1

2

USER’S MANUAL X 1

3

www.avenview.com

Page 3

2.2 BEFORE INSTALLATION

• Put the product in an even and stable location. If the product falls down or drops, it may cause an injury or malfunction.

• Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high humidity.

• Use the DC power adapter with correct specifications. If inappropriate power supply is used then it may cause a fire.

• Do not twist or pull by force ends of the UTP cable. It can cause malfunction.

www.avenview.com

Page 4

2.3 PANEL DESCRIPTION

2.3.1 Front Panel

1
2

2.3.2 Rear Panel

3 4 5 6

2.3.3 Bottom Panel

1. Power LED 2. Signal LED

3. Power Jack 4. HDMI Input

5. HDMI Local Output 6. CAT 5/6/7 Output 1 – 4

7. SW1: EDID Mode 8. SW2: EDID – Full HD Selection

9. SW3: EDID – Audio Selection 10. SW4: 3D/2D Selection

www.avenview.com

7

8

9

10

Page 5

3. EDID LEARNING

1. Power up the HDM3D-C5SP-4. Connect to HDMI OUTPUT with the display you want the HDM3D-C5SP-4 to learn
its EDID.

2. To learn the display’s EDID for source device connected to HDMI OUTPUT, Set SW1 to left Position. Power on and
wait for about 2-3 seconds to complete the EDID learning process; the users do not need to power cycle again or even

twice while plugging on different displays.

Left Position Right Position

SW1

SW2

SW3

SW4

- The instant switching is enabled only when the video and audio setting of the source has been adjusted to
“Auto” or “Pass Through”

DEFAULT EDID EDID LEARNING

FULL HD HD

AUDIO-MULTI CHANNEL AUDIO – 2 CHANNEL

3D 2D

4. INSTALLATION

To setup Avenview HDM3D-C5SP-4 follow these steps for connecting to a device:

1. Turn off all devices including monitors / TV

2. Connect to a HDMI source (such as a Blu-Ray Disc player) to HDMI Input of HDM3D-C5SP-4

3. Connect the receiver HDM-C53X-R or HDM-C5-R-M to HDM3D-C5SP-4 from RJ45 Out with CAT5 / CAT6 cable

4. Plug in 5V 4A DC Power (supplied).

5. Power on the HDMI display

6. Power on HDMI Sources.

www.avenview.com

Page 6

5. GENERAL TROUBLESHOOTING

PROBLEM POSSIBLE SOLUTION

NO IMAGE

SCREEN DEFECTS
APPEAR

EQUALIZER SET­TINGS

• Check if connection to the source and the display are correct.

• Ensure that display device supports 480p, 720p and 1080p resolution

• This product supports up to 1080p resolution.

• Check the HDMI connection

• If outputting from a PC. Check the maximum resolution range of the graphics card.

• Please check the RX (Receiver) Dial Mode to ensure it is on Min or gradually increase
it to Max until the video appears.

WARNING

Do Not Over Power The Eq Signal Strength

When Adjusting The Eq Please Ensure A Slow Clockwise

Turn From Min-Max

Stop Once The Picture/Audio Is Working Properly

Do Not Continue To Turn Dial.

Persistance Will Cause An Over Power Condition Of The Signal

And May Affect Long Term Reliability.

Thank You.

www.avenview.com

Page 7

5. SPECIFICATIONS

ITEM DESCRIPTION

UNITS HDM3D-C5SP-4

UNIT DESCRIPTION HDMI 1.3 Transmitter / Splitter over CAT5 / CAT6 with Full 3D Support

HDMI COMPLIANCE HDMI Deep Colour & Full 3D

HDCP COMPLIANCE Yes

VIDEO BANDWIDTH Single Link 225 MHz (6.75Gbps)

SUPPORTED RESOLUTIONS 480i / 480p / 720p / 1080i / 1080p60

RESOLUTION AND DIS­TANCE

AUDIO SUPPORT Surround Sound (up to 7.1 Ch) or Stereo Digital Audio

EQUALIZATION Built-in

INPUT TMDS SIGNAL 1.2 Volts (peak-to-peak)

INPUT DDC SIGNAL 5 Volts (peak-to-peak, TTL)

ESD PROTECTION

INPUT 1 x HDMI

OUTPUT 4 x Rj45

HDMI CONNECTOR Type A (19 pin female)

RJ45 CONNECTOR WE/SS 8P8C

DIMENSIONS (L X W X H) 7.6” x 4.3” x 1.1”

POWER SUPPLY 5V 4A DC

POWER CONSUMPTION 13 Watt (max)

Full HD: (1080p) ~ 40meter (130feet) (CAT5e) / 50meter (165feet) (CAT6)

HD: (720p/1080i) ~ 50meter (165feet) (CAT5e) / 60meter (200feet) (CAT6)

- Human body model — ±15kV (air-gap discharge) & ±8kV (contact
discharge)

- Core chipset — ±8kV

Environmental

OPERATING TEMPERATURE 32˚ ~ 104˚F (0˚ to 40˚C)

STORAGE TEMPERATURE -4˚ ~ 140˚F (-20˚ ~ 60˚C)

RELATIVE HUMIDITY 20~90% RH (no condensation)

www.avenview.com

Page 8

6. HDMI PIN DEFINITION

Type A (Receptacle) HDMI

Pin 1

Pin 2

Pin 3

Pin 4

Pin 5

Pin 6

Pin 7

Pin 8

Pin 9

Pin 10

TMDS Data2+

TMDS Data2 Shield

TMDS Data2–

TMDS Data1+

TMDS Data1 Shield

TMDS Data1–

TMDS Data0+

TMDS Data0 Shield

TMDS Data0–

TMDS Clock+

Pin 11

Pin 12

Pin 13

Pin 14

Pin 15

Pin 16

Pin 17

Pin 18

Pin 19

TMDS Clock Shield

TMDS Clock–

NC

Reserved (N.C. on

device)

SCL

SDA

DDC/CEC Ground

+5V Power

Hot Plug Detect

www.avenview.com

Page 9

Notice

1. All HDMI over CAT5 transmission distances are measured using Belden CAT6A (625MHz), 4-Pair,
U/UTP-Unshielded, Riser-CMR, Premise Horizontal Cable, 23 AWG Solid Bare Copper Conductors,
Polyolefin Insulation, Patented Double-H spline, Ripcord, PVC Jacket using Quantum 980 signal
HDMI Video Generator Module Video Pattern Testing.

2. The transmission length is largely affected by the type of category cables, also the type of HDMI
sources, and the type of HDMI display. The testing result shows solid UTP cables (usually in the
form of 300m or 1000ft bulk cable) can transmit a lot longer signals than stranded UTP cables
(usually in the form of patch cords). Shielded STP connectors are better suit than unshielded UTP
connectors. A solid UTP CAT5e cable shows longer transmission length than stranded STP CAT6
cable. For long extension users, solid cables are your only choice.

3. EIA/TIA-568-B termination (T568B) for category cables is recommended for better performance.

4. To reduce the interference among the unshielded twisted pairs of wires in category cable, you can
use shielded STP cables with shielded connector to improve EMI problems, which occurs in long
transmission.

5. Because the quality of the category cables has the major effects in how long transmission distance
will be made and how good is the received display, the actual transmission length is subject to your
category cables. For resolution greater than 1080i or 1280x1024, a solid CAT6 cable is the only
viable choice.

PERFORMANCE GUIDE FOR HDMI OVER CATEGORY CABLE TRANSMISSION

PERFORMANCE RATING TYPE OF CATEGORY CABLE

WIRING

SOLID

STRANDED

TERMINATION PLEASE USE EIA/TIA-568-B TERMINATION (T568B) AT ANY TIME

SHIELDING

UNSHIELDED (UTP)

SHIELDED (STP)

UNSHIELDED (UTP)

SHIELDED (STP)

CAT5 CAT5E CAT6

««« «««« ««««

««« «««« «««««

« «« ««

« « ««

www.avenview.com

Page 10

Notes

www.avenview.com

Page 11

Avenview Warranty Certificate

AVENVIEW CORP. (“Avenview”) warrants Avenview-branded product(s) contained in the original packaging against defects in materials and workmanship when used
normally in accordance with Avenview's enclosed manual guidelines for a period of THREE (3) YEARS from the date of original retail purchase - Warranty Period. Avenview’s
published guidelines include but are not limited to information contained in technical specifications, user manuals and service communications.

LABOR: During the Warranty Period of THREE (3) YEARS, Avenview will repair or replace the product(s) at no cost using new or used parts equivalent to novel performance
and reliability if the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Labor applicable to product(s) after Warranty Period. For labor costs,
please contact [e-mail].

PARTS: During the Warranty Period of of THREE (3) YEARS, Avenview will supply new or rebuilt replacements in exchange for defective parts of the product(s) at no cost if
the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Parts applicable to product(s) after Warranty Period. For part(s) costs, please contact

[e-mail].

To obtain Warranty: (a) proof of purchase in the form of a bill of sale or receipted invoice reflecting that the registered product(s) is within warranty period must be presented

to obtain warranty service; (b) product(s) must be registered at time of purchase. Failure to do so will result in applicable parts and labor charges. Returning product(s) must
be shipped in Avenview’s original packaging or in packaging pertaining equal degree of protection to Avenview’s. Both Avenview and purchaser are responsible for freight
charges and brokerages when shipping the product(s) to the receiver.

This warranty does not apply to any non-Avenview branded product(s); non-registered Avenview product(s). This warranty does not apply: (a) to cosmetic damage, including
but not limited to scratches, dents and broken cords; (b) to damage caused by use with another product; (c) to damage caused by accident, abuse, misuse, liquid contact, fire,
earthquake or other external cause; (d) to damage caused by operating the Avenview product(s) outside Avenview’s manuals or guidelines; (e) to damage caused by service
performed by anyone who is not a representative of A venview or an Avenview authorized personnel; (f) to defects caused by normal wear and tear or otherwise due to the
normal aging of the Avenview product(s), or (g) if any serial number has been removed or defaced from the Avenview product(s).

AVENVIEW IS NOT LIABLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR

CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOSS OF USE; LOSS OF REVENUE; LOSS OF ACTUAL OR
ANTICIPATED PROFITS (INCLUDING LOSS OF PROFITS ON CONTRACTS); LOSS OF THE USE OF MONEY; LOSS OF ANTICIPATED SAVINGS; LOSS OF BUSINESS;
LOSS OF OPPORTUNITY; LOSS OF GOODWILL; LOSS OF REPUTATI ON; LOSS OF, DAMAGE TO, COMPROMISE OR CORRUPTION OF DATA; OR ANY INDIR ECT
OR CONSEQUENTIAL LOSS OR DAMAGE REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.

Some states do not allow the inclusion or limitation of incidental or consequential damages, or allow limitations on duration implements of the Warranty Period; therefore the above limitations or
exclusions may not be applicable to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

NOT COVERED BY THIS WARRANTY

275 Woodward Avenue, Kenmore, NY 14217

1.866.508.0269

AV Connectivity, Distribution And Beyond...

TECHNICAL SUPPORT

Disclaimer

While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of
Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this
documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages
in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and documentation provided herein.

Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability, function or design.
With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties regarding such products, including but
not limited to, the implied warranties of merchantability, fitness for a particular purpose, and non-infringement.