Page 1
VIDEO WALLS VIDEO PROCESSORS
VIDEO MATRIX SWITCHES
EXTENDERS SPLITTERS WIRELESS
CABLES & ACCESSORIES
Control Your Video
4x1 HDMI 2.0 Quad Multiviewer with
4K@60 UHD Scaler on Output
© 2016 Avenview Inc. All rights reserved.
The contents of this document are provided in connection with Avenview Inc. (“Avenview”) products. Avenview makes no representations or
warranties with respect to the accuracy or completeness of the contents of this publication and reserves the right to make changes to specifications
and product descriptions at any time without notice. No license, whether express, implied, or otherwise, to any intellectual property rights is granted
by this publication. Except as set forth in Avenview Standard Terms and Conditions of Sale, Avenview assumes no liability whatsoever, and claims any
express or implied warranty, relating to its products are is strictly prohibited.
Model #: HDM2-SPLITPRO-T4K
HDM2-SPLIPRO-T4K
Page 2
www.avenview.com
Page
2
TABLE OF CONTENTS
1. GETTING STARTED ..........................................................................................................................1
1.1 IMPORTANT SAFEGUARDS ..............................................................................................................1
1.2 SAFETY INSTRUCTIONS. ..................................................................................................................1
1.3 REGULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC) ........................... 2
2.
INTRODUCTION ..............................................................................................................................3
2.2 PACKAGE CONTENT... .....................................................................................................................5
2.3 BEFORE INSTALLATION ...................................................................................................................5
2.4 APPLICATION DIAGRAM ..................................................................................................................6
3. PANEL DESCRIPTION........................................................................................................................7
3.1 INPUT PANEL (HDM2-SPLITPRO-T4K) FRONT.............................................................................7
3.2 INPUT PANEL (HDM2-SPLITPRO-T4K) REAR.................................................................................7
4.
IR REMOTE CONTROL.....................................................................................................................8
4.1 INSTALLATION AND CONTROL SOFTWARE................................................................................9
5.
SPECIFICATIONS .............................................................................................................................20
2.1 FEATURES ..........................................................................................................................................4
Page 3
www.avenview.com
Page
1
SECTION 1: GETTING STARTED
1.1 IMPORTANT SAFEGUARDS
Please read all of these instructions carefully before you use the device. Save this manual for future reference.
What the warranty does not cover
• Any product, on which the serial number has been defaced, modified or removed.
• Damage, deterioration or malfunction resulting from:
• Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or failure to
follow instructions supplied with the product.
• Repair or attempted repair by anyone not authorized by us.
• Any damage of the product due to shipment.
• Removal or installation of the product.
• Causes external to the product, such as electric power fluctuation or failure.
• u se of supplies or parts not meeting our specifications.
• Normal wear and tear.
• Any other causes which does not relate to a product defect.
• Removal, installation, and set-up service charges.
1.2 SAFETY INSTRUCTIONS
The HDM2-SPLITPRO-T4K 4x1 Quad multiviewer with 4K UHD support on the output and audio has been tested for
conformance to safety regulations and requirements, and has been certified for international use. However, like all electronic
equipments, the HDM2-SPLITPRO-T4K should be used with care. Read the following safety instructions to protect yourself
from possible injury and to minimize the risk of damage to the unit.
!
Do not dismantle the housing or modify the module.
!
Dismantling the housing or modifying the module may result in electrical shock or burn.
!
Refer all servicing to qualified service personnel.
!
Do not attempt to service this product yourself as opening or removing housing may expose you to dangerous voltage
or other hazards
! Keep the module away from liquids.
!
Spillage into the housing may result in fire, electrical shock, or equipment damage. If an object or liquid falls or spills on
to the housing, unplug the module immediately.
!
Have the module checked by a qualified service engineer before using it again.
!
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the device before cleaning.
Page 4
www.avenview.com
Page
2
1.3 REG
ULATORY NOTICES FEDERAL COMMUNICATIONS COMMISSION (FCC)
This equipment has been tested and found to comply with part 15 of the F
CC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
Any changes or modifications made to this equipment may void the user’s authority to operate this equipment.
Warning symbols Description
ONLY USE THE PROVIDED POWER CABLE OR
POWER ADAPTER SUPPLIED. DO NOT TAMPER WITH
THE ELECTRICAL PARTS. THIS MAY RESULT IN
ELECTRICAL SHOCK OR BURN.
DO NOT TAMPER WITH THE UNIT. DOING SO WILL
VOID THE WARRANTY AND CONTINUED USE OF
THE PRODUCT.
THE VIDEO BOARDS ARE VERY SENSITIVE TO STATIC.
PLEASE ENSURE IF RACK MOUNTED OR INSTALLED ON
A SURFACE, IT SHOULD BE IN A GROUNDED
ENVIROMENT.
Page 5
www.avenview.com
Page
3
2.
INTRODUCTION
This 4 x1 multiviewer Scaler was developed for the purpose of supporting higher output resolution (4K@60) for multiple
sources on a single screen.
This HDMI device can accept 4 HDMI input digital sources and combine (4) four video signals onto a single HDMI UHD or
HD monitor The user can easily manage each input via the supplied Control Software and create any layout and position of
any of the 4 (four) Inputs on a single monitor. This device supports full range of input video resolutions up to WUXGA@60
(RB) or full HD1080p and audio RCA breakout supported for external audio distribution systems. Audio channels can be
selected to playback with input or can be muted.
Fast Switching – This device can input any 4 HDMI input digital sources and then combine, (4) four video signals onto a
single HDMI HD monitor. The user will benefit with from its processing power to switch between the 8 user defined function
via IR Remote, Ethernet or RS232.
Crop – This device can Crop any 4 HDMI input digital sources to remove black bars and then combine, (4) four video signals
onto a single HDMI HD monitor. This device can be configured using the supplied Control software via Ethernet or RS232 to
set the desired layout on the connected screens.
PIP,PAP, Overlay – This device can input any 4 HDMI digital sources and then combine, (4) four video signals onto a single
HDMI HD monitor, which the user can select picture In picture (PIP) , picture Aside picture (PAP) or overlay with the
supplied Control Software via Ethernet or RS232 to set the desired layout configuration.
Window Scale and Position – The user can easily change the individual channel size and choose different position and
layout on the single monitor with the Control Software via Ethernet or RS232 to set the desired layout configuration.
Scalable Rotation (90˚ & -90˚) – The user can easily Rotate/Scale only a single input/window image 90˚ left and right. This
device can be configured with the Control Software, IR Remote, Ethernet, RS232 or front panel buttons .
Page 6
www.avenview.com
Page
4
- Fast switching between input channels and combined multiple images on single HD monitor;
- Crop the (4) four HDMI Input Channels;
- Supports PIP, PAP and multi-windows layout configurations;
- Single Input Rotation (90˚ left & right ) functions;
- 8 preset Hot keys with 4 Custom layouts and 4 Full screen layouts within the supplied control software;
- 8 Custom saved layout buttons via the IR Remote;
- Input resolution support full range of video resolutions up to WUXGA@60 (RB) or full HD1080p;
- Output resolution support Full HD or upscale to 4K@60 (3840x2160);
- Audio dembedded via RCA Left and Right audio connectors
- RS 232 port for Service mode and firmware upgrade;
- Supports RS 232,Ethernet, IR Remote and front panel buttons;
- Factory Reset feature.
2.1
FEATURES
Page 7
www.avenview.com
Page
5
2.2 PACKAGE CONTENTS
Before you start the installation of the converter, please check the package contents.
1
HDM2-SPLITPRO-T4K
X 1
2
POWER SUPPLY (12V 5A)
X 1
3
IR REMOTE X 1
5
RACKMOUNT BRACKET X 2
2.3 BEFORE INSTALLATION
•
Put the product in an even and stable location. If the product falls down or drops, it may cause an injury or malfunction.
Don’t place the product in too high temperature (over 50°C), too low temperature (under 0°C) or high humidity.
•
Use the DC power adapter with correct specifications. If inappropriate power supply is used then it may cause a fire.
• Do not twist or pull by force ends of the video cable. It can cause malfunction.
4
SOFTWARE X 1
6
USER MANUAL
X 1
Page 8
www.avenview.com
Page
6
2.4 APPLICATION DIAGRAM
Page 9
www.avenview.com
Page
7
3. PANEL DESCRIPTION
3.1 INPUT PANEL (HDM2-SPLITPRO-T4K) Front
*
Some display/monitor brands the window border may have interference, adjusting the display's motion setting may
resolve the interference issue.
3
3.2 INPUT PANEL (HDM2-SPLITPRO-T4K) Rear
9. HDMI IN 1-4: Connect up to 4 HDmI devices to the
INpu T ports 1-4( Blu-ray /Set-Top Box or PC)
10.
HDMI OUT: Connect a single HDmI HD monitor/
Display to view the four inputs connected.
11.
Stereo Audio L/R: Connect red white audio RCA
jacks to extract audio to an external audio source.
12.
RS-232: D-Sub 9pin port for sending and controlling
the unit by PC/Notebook via RS232 cable.
13. Ethernet: RJ45 jack for sending and controlling the
unit by pC/Notebook via ethernet cable.
14.
DC 12V: plug the 12V DC power supply into the
unit supplied to an AC 110v outlet.
12
11
13
14
10
9
1 2 4
5678
1.
Reserved Buttons: F1 & F2
5.
Full Screen Button
2.
Preset Layouts: PAP1/2/3/4
3.
IR Sensor: Receive IR commands from IR remote
4.
Resolution Button: 4K UHD/1080p
Rotation Button: +90 & -90
6.
Window Source Selection: Source A/B/C/D
7.
Window Label Button: Label ON/OFF
8.
Page 10
www.avenview.com
Page
8
4.
IR REMOTE CONTROL
1.
F1: 1st press activate DVI / 2nd press activate HDMI mode.
2.
F RESERVED: N/A
3.
4.
POWER: To power ON or OFF the unit
5.
ROTATION: Rotate Window A only +90 or -90.
6.
LABEL: To toggle window label ON/OFF
7.
SOUND: Easily switch between input audio source.
8.
BACKGROUND: To enable and setup background picture.
9.
4K2K: Enable 4k@60 UHD resolution on the output.
10.
1080p: Enable 1080p@60 resolution on the output.
11.
720p: Enable 720p@60 resolution on the output.
12.
M
UTE: To mute the audio on output
13.
CUSTOM LAYOUT 1-8: Enables the configured user defined layout1-8
14.
*
Audio function only work under A to D.
F RESERVED: N/A
QUAD LAYOUT 1: Enables the predefined layout 1
15. QUAD LAYOUT 2: Enables the predefined layout 2
16.
QUAD LAYOUT 3: Enables the predefined layout 3
17.
QUAD LAYOUT 4: Enables the predefined layout 4
18.
FULL SCREEN LAYOUT 1-4: Enables the source input to full screen window mode A-D
Page 11
www.avenview.com
Page
9
4.1 INSTALLATION (HDM2-SPLITPRO-T4K)
HARDWARE SETUP
To setup Avenview HDM2-SPLITPRO-T4K follow these steps below:
1.
Mount or fix the HDM2-SPLITPRO-T4K on a secure shelf, AV rack or steady surface;
2.
Ensure the power is off on the HDM2-SPLITPRO-T4K, all source devices and displays that will be connected;
3.
Connect your (4) four HDMI cables to the (4) four HDMI sources such as (Blu-ray player, Laptop or Set-Top-Box or
Gaming device);
4.
Connect your HDMI cables to the single HD Displays, LCD or PC monitors that is receiving the video signals.
5.
Power on all devices.
6.
Connect your computer to HDM2-SPLITPRO-T4K via RS232, RS-232 to USB or Ethernet cable in order
to control via Telnet or RS232.
SERIAL PORT SETTING
RS-232 Wiring (Cross Cable Connection)
HDM-SPLITPRO-4K
Remote Controller(PC)
PIN Assignment
PIN De finition
1 NC
1 NC
2 TxD
2 RxD
3 RxD
3 TxD
4 NC
4 NC
5 GND
5 GND
6 NC
6 NC
7 NC
7 NC
8 NC
8 NC
9 NC
9 NC
è
ç
RS-232 SETTINGS
Baud Rate: 115200bps
Data Bit: 8 bits
parity: None
flow Control: None
Stop Bit: 1
Page 12
Control through RS-232 port / Ethernet port
1. Please note when power cycling device, please restart unit at least 5 to 15 seconds after to allow the power
capacitors to discharge.
2.
The HDM2-SPLITPRO-T4K PC control software operates with Microsoft Windows 98, 2000, XP, 7, 8 through
the interface of Ethernet or RS-232 serial control.
3. Through software and COM port you can assign an IP address before connecting via RJ45.
Please NOTE: (Under Microsoft Windows 7, please run software as administrator).
Once the software is installed click on the ICON, the following dialog will pop-up. First time connection,
please connect via RS232 serial cable.
RS-232 serial Mode: Use RS-232 to connect the port on device and computer. Select
the correct COM port and
click the OK button.
Ethernet Mode: Enter the IP address of the device and click the OK button.
After the software control setting is complete and correct, it will enter directly to control interface.
4.2 INSTALLATION (HDM2-SPLITPRO-T4K) with PC Control Software
www.avenview.com
Page 10
Page 13
1.
2.
Output Settings
Users can set up the desiginated inputs, to each window A~D or duplicate, output resolution, PAP
predefined layout
setting or single input rotation.
(1) Source Selection
For each display window, you can assign the video souras
the caption below:
1
2
3
4
5
6
7 8
Connection Status:
This shows the active connection status. If connected by RS-232 serial Mode device, the icon is . If connected
by ethernet . Easily change the control method, by clicking on the button.
www.avenview.com
Page 11
4.2 CONTROL INTERFACE
Page 14
(2) Quick Selection Tabs
Provided in the software 9 default modes (5 PAP and 4 Full Screen) and 8 custom modes for you to create.
(3) Output Resolution
Set the output resolution from 640x480-4K@60 to match the connected Monitor Timings
(4) Save Layout
Also the user can define their own 8 custom layouts and save the frequently used scenarios into the flash memory.
www.avenview.com
Page
12
Page 15
As illustrated below, users can resize any window by simply dragging the highlighted box with the mouse and
immediately see the results on the attached monitor. The different colors of the frames represent the different
inputs for easy identification. The Horizontal and Vertical coordinate shows the position of input source on the
screen. In addition, the display ratio can be adjusted to view the layout in software (Zoom in Zoom out) .
3.
Advanced Setting
(5) Display Panel
www.avenview.com
Page
13
Page 16
Users can adjust each display area and input source as desired. To proceed with this function user have to click on
the specific channel A, B, C, or D, as indicated by the icons in the control panel as shown above.
After the specific channel is chosen, users can click on the "CROP ENABLE" box, then crop the display area of that
and other channels. The control panel of the software illustrates by preview on how those settings would to be
presented at the output. Using "DIVIDE- Horizontal/Vertical"
(2) Label Text
In here, users can easily rename /label the input to be shown on the window with the video to identify the input.
(3) Sound
To set and match which audio source to the output video through the R/L channels.
(4) Background
To set up the background of each window. The CS has 4 default pictures for the user to select. To change the
default picture,please click the button to select the picture that would be used.
(5) Window Label
Users can simply determine if the window’s label/border can be shown or invisble.
(1) Window settings
www.avenview.com
Page
14
Page 17
(1) Learn EDID from Default
Select Default EDID
Select Input
Click
button to learn default EDID.
(2) Learn EDID from File
Select input
Click button to select the EDID file and write it into input
4.
EDID (Extended Display Identification Data)
www.avenview.com
Page
15
Page 18
5.
System Setting
(1) Firmware Update
Click button to perform authorized firmware update.
The “Firmware update” window pops up as below.
Please select the correct COM port or click “Scan” button to connect device.
www.avenview.com
Page
16
Page 19
To change the OSD (window label) font, please click “OSD Font Update” window and click
“update” to change OSD font.
www.avenview.com
Page
17
Click “update” button to do firmware update
.
Page 20
(2) Factory Reset
Click button to performa factory default reset.
The process will take approx. 25 seconds.
www.avenview.com
Page
18
Page 21
6.
IP Configure
To use Ethernet control users should click on the button button to set the network IP range. Please see
the caption below. After the information has been complete, please click the button.
7.
Info
Displays the Software and firmware version.
8.
Refresh
This function will gather the changes made wihin software and hardware. Then
update the software interface state with its current info.
www.avenview.com
Page
19
Software/firmware information is subject to change without prior notice
Page 22
www.avenview.com
Page
20
5.
SPECIFICATIONS
Item Description
UNITS
UNIT DESCRIPTION
HDCP COMPLIANCE
VIDEO BANDWIDTH
HDM2-SPLITPRO-T4K
4x1 HDMI 2.0 Quad multiviewer with Rotation, 4K@60 support on output
Yes 2..2
HDMI COMPLIANCE
Input: HDMI [2.25G to 6.75Gbps] / Output: Single-link 600MHz [18Gbps]
Input: HDMI 1.4 /Output: HDMI 2.0a
VIDEO FORMAT SUPPORT
HDMI 2.0
INPUT SUPPORTED
RESOLUTIONS
PC -VGA 640x480, XGA (1024 x 768), SXGA (1280 x 1024),
UXGA (1600 x 1200), WUXGA (1920 x 1200)
480i/720p/1080i/1080p@60 and up to 1920x1200@60
OUTPUT SUPPORTED
RESOLUTIONS
720p 50Hz, 720p 60Hz, 1080p 24Hz,
1080p 25Hz, 1080p 30Hz, 1080p 50Hz, 1080p 60Hz, 1920X1200RB Hz,
3840x2160 60 Hz and 4K2K@60 (4:4:4 8bits)
AUDIO SUPPORT
Bypass
LPCM 2CH, 6CH, 8CH/AC3/DTS/Dolby Digital Plus/ Dolby TruHD/DTS-HD
INPUT
4x HDMI + 1xRS-232 + 1x RJ-45(Ethernet)
OUTPUT
CONTROL
RJ45 CONNECTOR
ESD PROTECTION
WEIGHT
DIMENSIONS (L X W X H)
POWER SUPPLY
POWER CONSUMPTION
1 x HDMI
RS 232 / IP Control
WE/SS 8P8C with 2 LED indicators
Human body model — ±15kV [air-gap discharge] &
±8kV [contact discharge]
3.3 lbs
12.5" x 6.8" x 1.7"
12V/5A DC (US/EU standards, CE/FCC/UL certified)
8.9W
Environmental
OPERATING TEMPERATURE 32˚ ~ 104˚F (0˚ to 40˚C)
STORAGE TEMPERATURE -4˚ ~ 140˚F (-20˚ ~ 60˚C)
RELATIVE HUMIDITY 20~90% RH (no condensation)
Page 23
www.avenview.com
Avenview Warranty Certificate
AVENVIEW CORP. (“Avenview”) warrants Avenview-branded product(s) contained in the original packaging against defects in materials and workmanship when used
normally in accordance with Avenview's enclosed manual guidelines for a period of THREE (3) YEARS from the date of original retail purchase - Warranty Period. Avenview’s
published guidelines include but are not limited to information contained in technical specifications, user manuals and service communications.
LABOR: During the Warranty Period of THREE (3) YEARS, Avenview will repair or replace the product(s) at no cost using new or used parts equivalent to novel performance
and reliability if the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Labor applicable to product(s) after Warranty Period. For labor costs,
please contact [email protected].
PARTS: During the Warranty Period of of THREE (3) YEARS, Avenview will supply new or rebuilt replacements in exchange for defective parts of the product(s) at no cost if
the product(s) is determined to have abide by Avenview’s published guidelines. Cost of Parts applicable to product(s) after Warranty Period. For part(s) costs, please contact
To obtain Warranty: (a) proof of purchase in the form of a bill of sale or receipted invoice reflecting that the registered product(s) is within warranty period must be presented
to obtain warranty service; (b) product(s) must be registered at time of purchase. Failure to do so will result in applicable parts and labor charges. Returning product(s) must
be shipped in Avenview’s original packaging or in packaging pertaining equal degree of protection to Avenview’s. Both Avenview and purchaser are responsible for freight
charges and brokerages when shipping the product(s) to the receiver.
NOT COVERED BY THIS WARRANTY
This warranty does not apply to any non-Avenview branded product(s); non-registered Avenview product(s). This warranty does not apply: (a) to cosmetic damage, including
but not limited to scratches, dents and broken cords; (b) to damage caused by use with another product; (c) to damage caused by accident, abuse, misuse, liquid contact, fire,
earthquake or other external cause; (d) to damage caused by operating the Avenview product(s) outside Avenview’s manuals or guidelines; (e) to damage caused by service
performed by anyone who is not a representative of A venview or an Avenview authorized personnel; (f) to defects caused by normal wear and tear or otherwise due to the
normal aging of the Avenview product(s), or (g) if any serial number has been removed or defaced from the Avenview product(s).
AVENVIEW IS NOT LIABLE FOR DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY OR
CONDITION, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING BUT NOT LIMITED TO LOSS OF USE; LOSS OF REVENUE; LOSS OF ACTUAL OR
ANTICIPATED PROFITS (INCLUDING LOSS OF PROFITS ON CONTRACTS); LOSS OF THE USE OF MONEY; LOSS OF ANTICIPATED SAVINGS; LOSS OF BUSINESS;
LOSS OF OPPORTUNITY; LOSS OF GOODWILL; LOSS OF REPUTATI ON; LOSS OF, DAMAGE TO, COMPROMISE OR CORRUPTION OF DATA; OR ANY INDIRECT
OR CONSEQUENTIAL LOSS OR DAMAGE REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE EXCLUSIVE REMEDY OF THE CONSUMER.
Some states do not allow the inclusion or limitation of incidental or consequential damages, or allow limitations on duration implements of the Warranty Period; therefore the above limitations or
exclusions may not be applicable to you. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
1100 Military Road, Kenmore, NY 14217
1.866.508.0269
Page 24
TECHNICAL SUPPORT
Disclaimer
While every precaution has been taken in the preparation of this document, Avenview Inc. assumes no liability with respect to the operation or use of
Avenview hardware, software or other products and documentation described herein, for any act or omission of Avenview concerning such products or this
documentation, for any interruption of service, loss or interruption of business, loss of anticipatory profits, or for punitive, incidental or consequential damages
in connection with the furnishing, performance, or use of the Avenview hardware, software, or other products and documentation provided herein.
Avenview Inc. reserves the right to make changes without further notice to a product or system described herein to improve reliability, function or design.
With respect to Avenview products which this document relates, Avenview disclaims all express or implied warranties regarding such products, including but
not limited to, the implied warranties of merchantability, fitness for a particular purpose, and non-infringement.
Control Your Video
Avenview Canada
151 Esna Park Drive, Unit 11-12
Markham, ON L3R 3B1
Phone: +1 905 907 0525
Email: [email protected]
Sales: [email protected]
Avenview USA
1100 Military Road
Kenmore, NY 14217
Phone: +1 716 218 4100 x223
Fax: +1 866 387 8764
Email: [email protected]
Avenview Europe
Phone: +31 085 2100 613
Email: [email protected]
Avenview Asia
Email: [email protected]
Sales: [email protected]
Loading...