Page 1
User’s Manual
Moonlight 600TVL Vandal proof Dome
Model No. IV-MS6860VPA
Video System NTSC/ PAL System
Sensor 1/3" Sony Super HAD II CCD Hitachi 14bit DSP
Pixel NTSC: 768H*494V; PAL: 752H*582V
Resolution 600TVL(Color), 650TVL(B/W)
Lens Aspherical 2.8-10mm Lens with Auto Iris and IR-CUT
True Day & Night
COLOR,B/W(Saturation protection Erea Select),EXT,
AUTO(D/N LEVEL;LOW/MIDDLE/HIGH)
Sync. Internal
Scanning 2:1 Interlace
Signal Noise Ratio 50dB Min.
Burst Level 0.286Vp-p
ECLIPSE DAY/ NIGHT (BLACK/ GRAY)
3D-XDNR OFF, ON (0~20), COLOR SUPRESSION
SBLC OFF/ LOW/ MID/ HIGH
D-EFFECT MIRROR (H /V /ROTATE), FREEZE
D-ZOOM LEVEL, LIMIT
Motion Detection ON/ OFF (4 Programmable Zone)
Privacy Mask ON /OFF (4 Programmable Zone)
Communication RS485, PELCO-D Protocol
Electronic Shutter NTSC: 1/60-1/60,000S; PAL: 1/50-1/60,000S
White Balance ATW/ MANUAL/ PUSH
Backlight Compensation OFF, ON (ZONE ADJUSTABLE)
Auto Gain Control Off/ On (0~20)
Gamma Correction 0.35/ 0.4/ 0.45/ 0.65/ 0.75 Selectable
Video Output 1V p-p,75Ω
Min. Illumination 0.00005Lux
Voltage Input DC12V (+20% -10%)
Power Current 180mA Max
Operation Temp. -10°C~50C
Storage Temp. -20°C~60°C
Humidity Range 30%~80% RH
Dimension ø128*98 mm
Net Weight 720g
Technical Specifications:
Feature:
1/3" Sony Super HAD II CCD, Hitachi 14bit DSP
Super High Resolution 600TVL
Low illumination 0.00005Lux
Aspherical 2.8-10mm Lens with Auto Iris and IR-CUT Module
Full OSD operation Controlled via RS485 or OSD joystick inside
Can always remain in color in low light conditions
Dual Power DC12/ AC24V Optional
Vandal proof Dome
Installation:
To prevent shock or damage to the waterproof body, tighten all the screws and cover
Adjust the visor to prevent the lens from direct sunlight
Do not directly touch the front glass. To clean the dust, wipe with soft cloth with alcohol.
Don’t install it in the place where dithering and shake often
Don’t install it in the place where temperature is above 50°C or below –20°C
Video line tie-in and DC tie-in must be avoided to touch water.
If abnormal, please power off and contact the manufacturer
Note: Non-regulated power supply may cause camera damaged.
Page 2
External OSD Operation
-- Communication Setting of Keyboard and Camera:
MENU OPERATION：
Users’ Manual
MENU
LENS……………………………..DC/ESC
WHITE BAL……………………...ATW/PUSH/USER2/USER1
ANTI CR/MANUAL/PUSH LOCK
WDR……………………………….WDR/BLC/HLC/OFF
BACKLIGHT……………………...OFF/ON
DNR……………………………….OFF/3DNR/2DNR
DAY/NIGHT……………………AUTO/COLOR/EXIT1/EXIT2/IRED/B/W
IMAGE ADJ
GENERAL
RETURN…………………………...SAVE ALL/NOT SAVE
DC
BRIGHTNESS
AGC………………………………..0~20
FLICKERNESS…………………...OFF/ON
SHUTTER………………………….1/50~1/10K
DSS…………………………………OFF/X2~X512
2D-DNR
LEVEL…………………………AUTO/LOW/MID/HIGH
RETURN
GENERAL
CAM ID………………..0~255 optional
ID DISPLAY…………..OFF/ON
CAM TITLE…………...OFF/ON
LANGUAGE………….Eng/Chinese/Japanese/Germen/French/Russian/
Portuguese/Spanish/Korean
SYNC………………….INT
BAUDRATE………….2400~115200 BPS optional
VERSION…………….P1.21C
FACTORY RESET
The Camera has built-in Pelco-D Protocol. It can be connected and
controlled by the keypad or DVR. Please note to press key "SAVE" to
operate your changes on OSD MENU before exit.
How to connect in MINI keypad
Step 1:
Power up the camera and keypad, connect camera and keypad in
RS485 port.
Caution: RS485 has Negative and Positive port, please connect properly.
Otherwise the connection between keypad and camera will be failed.
Step 2:
Select the same protocol, baud rate and camera ID in both keypad/DVR
and camera.
Shift+1: Select Protocol ( Pelco-D for this camera )
Shift+2: Select baud rate ( 2400bps for this camera )
(Press LEFT/ RIGHT to select optional items, ENTER to confirm.)
Camera ID: Input the camera ID directly, ENTER to confirm.
Step 3:
After all the settings done properly, the keypad shall be able to control
the camera.
Press [Menu] to enter into the OSD Menu.
MENU
LENS
WHITE BAL
WDR
DNR
DAY/NIGHT
IMAGE ADJ
GENERAL
EXIT
DC
ATW
WDR
2DNR
AUTO
+…
+…
SAVE ALL
DC
BRIGHTNESS
AGC 14
FLICKERNESS OFF
DSS X2
SHUTTER 1/50
RETURN
DAY/NI(AUTO)
DELAY CNT
D/N LEVEL
RETURN
3 SEC
MID
MOTION
AREA
DISPLAY
DETECT AREA
SENSITIVITY
TOP
BOTTOM
LEFT
RIGHT
RETURN
1/4
OFF
8
1
7
1
11
PRIVACY
AREA
DISPLAY
POSITION
COLOR
TRANSP
MOSAIC
RETURN
1/15
OFF
WHITE
IMAGE ADJ
IMAGE
D-EFFECT
MOTION
PRIVACY
COLOR GAIN
RETURN
+…
+…
+…
+…
+…
GENERAL
CAM ID
ID DISPLAY
CAM TITLE
LANGUAGE
SYNC
BAUDRATE
VERSION
FACTORY RESET
RETURN
1
OFF
OFF
ENG
INT
9600 BPS
P1.91H
MOTION
AREA………………………...1/4~4/4
DISPLAY……………………. OFF/ON
DETECT AREA
SENSITIVIIY
TOP…………………………..0~15
BOTTOM……………………1~16
LEFT………………………...0~23
RIGHT……………………….1~24
RETURN
PRIVACY
AREA…………………….1/15~15/15
DISPLAY………………...OFF/ON
POSITION
COLOR…………………..WHITE/YELLOW/GREEN/BLUE/RED/
BLACK/GRAY optional
TRANSP
MOSAIC
RETURN
2D-DNR
LEVEL
RETURN
MID
DAY/NIGHT(AUTO)
DELAY CNT …………………0~15 SEC
D/N LEVEL…………………..LOW/MID/HIGH
RETURN
RS485 OSD Settings
Cable OSD Settings
ESC
BRIGHTNESS
AGC 14
FLICKERNESS OFF
DSS X2
RETURN
ESC
BRIGHTNESS
AGC………………………………..0~20
FLICKERNESS…………………...OFF/ON
DSS…………………………………OFF/X2~X512
RETURN
WDR
MODE WDR
BRIGHTNESS 110
CONTRAST MID
RETURN
WDR
MODE………………………………WDR
BRIGHTNESS……………………..0~255
CONTRAST………………………..MID/MID-HIGH/HIGH/LOW/MID-LOW
DAY/NI(IRED)
AREA
DELAY CNT
DAY→NIGHT
NIGHT→DAY
BRIGHTNESS
DWDR
CONTRAST
RETURN
AUTO
3 SEC
7
35
DAY/NIGHT(IRED)
AREA ………………………. AUTO/MANUAL
DELAY CNT…………………..0~15 SEC
DAY→NIGHT………………….0~255
NIGHT→DAY………………….0~255
BRIGHTNESS
DWDR
CONTRAST
RETURN
IMAGE
SHARPNESS
GAMMA
HR MODE
CONTRAST
RETURN
8
0.55
X3
32
IMAGE
SHARPNESS………………………0~15
GAMMA……………………………..0.38`~0.83
HRMODE…………………………...OFF/X1~X7
CONTRAST………………………….0~63
RETURN
D-EFFECT
DIS
D-ZOOM
MIRROR
FREEZE
NEGA/POSI
RETURN
OFF
OFF
OFF
OFF
POSI
D-EFFECT
DIS………………………………...OFF/ON
D-ZOOM………………………….OFF/X2~X16
MIRROR…………………………..OFF/V-FLIP/H-FLIP/HV-FLIP
FREEZE…………………………….OFF/ON
NEGA/POSI………………………..POSI/NEGA
RETURN
UP: OSD Option Upward
LEFT: OSD Option Leftward
ENTER: OSD Option Enter
RIGHT: OSD Option Rightward
DOWN: OSD Option Downward
VIDEO: Second Video
Loading...