Avaya T24 KIM Installation Manual
T24 Key Indicator Module
(KIM) Installation Card
The T24 Key Indicator Module (KIM) is an add-on device which provides 24 extra memory or
line buttons for the T7316E telephone. Up to nine KIMs can be connected to a T7316E
telephone.
A Station Auxiliary Power Supply (SAPS) is required for T7316E telephones that have five to
nine KIMs attached. For SAPS installation instructions, refer to the SAPS Installation Card
provided with the SAPS kit.
Single T24 KIM installation Multiple T24 KIM installation
Position the metal hooks
1
from the left side of the KIM
next to the slots on the right
side of the T7316E
telephone.
Firmly press the T7316E and KIM together.
Slide the KIM down until its
2
aligned with the T7316E
telephone.
Remove the stand
3
from the T7316E
telephone.
Connect the KIM
4
cord to the accessory
T24 KIM Installation
connector port on the
T7316E telephone.
Press here
to remove stand.
Position the T7316E
1
telephone and KIMs
together. Align the
hooks on each KIM
to the slots on the
next KIM.
Firmly press the T7316E and KIMs together.
Slide the KIMs down
2
until they are aligned
with the T7316E
telephone.
Remove the
3
stands from
KIMs and
the T7316E
telephone.
Connect each KIM
4
cord to the connector
port on the next KIM
in a daisy-chain
order.
KIM 3
KIM 2
Press here
to remove
stands.
KIM 1
Cord to
T7316E
Replace the stand on the T7316E telephone to
5
complete the installation.
Connect the cord
5
on the first KIM
to the accessory
connector port on
the T7316E
telephone.
Replace the stands on the KIMs and the
6
T7316E telephone to complete t he instal la tion.
KIM 1
T24 KIM initialization
KIM button number assignment
KIM indicators turn o n a nd fl ash du rin g t he fi rst ten se cond s
after powering up. It can take up to five minutes for the KIM
to initialize.
The default setting for the programmable memory buttons
B01
B02
B03
B04
B13
B14
B15
B16
on the KIM is blank. The side illustration shows the button
number assignment on a KIM.
Troubleshooting Tip: An Addon Errormessage appears
on the T7316E telephone display and an error tone is
generated when there is a connector problem with a KIM.
Check that the K IM cord is properly inserted into the
B05
B06
B07
B08
B09
B10
B11
B12
B17
B18
B19
B20
B21
B22
B23
B24
accessory connector port of the T7316E telephone.
T24 KIM coldstarts
Internal autodial number s can be autom atical ly assigne d to the programm able m emory bu ttons on the
KIM when a coldstart is performed. Internal autodial numbers are assigned in ascending order starting
on the top left button (button 01) on the KIM. A coldstart must be performed during the first ten seconds after powering up a KIM.
To coldstart an individual KIM To coldstart all KIMs
Unplug the T7316E telephone line cord, then
1
reconnect it to power up.
While the indicators are
2
flashing on the individual
KIM, simultaneously press
the top two and the bottom
two buttons on the lower
button set of the KIM, as
shown in the i llu s tration
(buttons: 05, 12, 17 and 24).
At the beginning of the coldstart, in dic ator s beside
3
each KIM button will briefly flash start ing at the
bottom right button (button 24).
Unplug the T7316E telephone line cord, then
1
reconnect it to power up.
While the indicators are
2
flashing on the first KIM
(next to the telephone),
simultaneously press the
top two buttons and the
bottom two buttons on the
KIM, as shown in the
illustration.
(buttons: 01, 12, 13 and 24)
At the beginning of the coldst art, i ndicators bes ide
3
each KIM button will briefly flash starting at the
bottom right button (button 24).
When the KIM coldstart is completed, the T7316E
4
telephone display automati cally re turns t o the ti me
and date.
2
When the KIM coldstart is completed, the T7316E
4
telephone display automatical ly returns to the time
and date.
1-800-4 NORTEL
www.nortelnetworks.com
P0603481_02
Printed in Canada
Loading...