Avaya Power Module in the Passport 5430 User Manual

Part No. 306622-A Rev 00
January 2000

4401 Great America Parkway
Santa Clara, CA 95054

Installing a Power Module
in the Passport 5430
Multiservice Access Switch

Copyright © 2000 Nortel Networks.

All rights reserved. Printed in the USA. January 2000.
The information in th is document is subject to cha nge without notice. The stat ements,

configurations, tech nic al data, and recomme ndations in this document are believed to be
accurate and reliable , but are presented without express or impl ie d wa rra nty. Users must take
full responsibility for their applications of any products specified in this document. The
information in this docum en t is pr opri etary to Nortel Networks NA Inc.

Trademarks

NORTEL NETWORKS is a trademark of Nortel Networks.
BayRS, BCC, and Passport are trademarks of Nortel Networks.
All other trademarks an d regist ere d trademarks are the property of their respective owners.

Statement of Conditions

In the interest of improving int ernal design, operational fu nction, and/or reliability, Nortel
Networks NA Inc. reserves the right to make changes to the products described in this document
without notice.

Nortel Networks NA Inc. does not assume any li abi l it y that may occur due to the use or
application of the product(s) or circuit layout(s) described herein.

USA Requirements Only

Federal Communications Commission (FCC) Compliance Notice: Radio Fre­quency Notice

Note: This equipment has been tested and found to comply with the limits for a Cl a ss A digital
device, pursuant to Part 15 of the FCC rules. These limi ts ar e designed to provide reasonable
protection against harmful interfere nce when the equipment is operated in a c o m mercial
environment. This equipment generates, uses, and can radiate radio frequency energy. If it is not
installed and used in accordance with the instruction manual, it may cause harmful interference
to radio communi cations. Operation of this equipment in a residential area is li kely to cause
harmful interference, in whic h ca se users will be required to take whatever measures may be
necessary to correct the int erference at their own expense.

ii

European Requirements Only

EN 55 022 Statement

This is to certify that the Nortel Networks Passport 5430 Multiservice Access Switchis shielded
against the generat ion of radio interferen ce in accordance with the application of Council
Directive 89/336/EEC, Article 4a. Conformity is declared by the application of EN 55 022 Class
A (CISPR 22).

Warning: This i s a Cla ss A product. In a domestic environment, th is product may cause radio
interference, in which case , the us er m ay be required to take appropriat e me asures.

Achtung: Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei
Betrieb dieses Gerätes Rundfunkstörungen auftrete n, in we lc he n Fällen der Benutzer für
entsprechende Gegenmaßnahmen verantwortlich ist.

Attention: Ceci est un produit de Classe A. Dans un environnement dom estique, ce produit
risque de créer des interférences radioélectriques, il appartiendra alors à l’utilisateur de prendre
les mesures spécifiques appropriées.

EC Declaration of Conformity

This product conforms (or th ese products conform) to the provisions of Council Directive 89/
336/EEC and 73/23/E EC . T he Declaration of Conformity is available on the Nortel Networks
World Wide Web site at http://libra2.corpwest.baynetworks.com/cgi-bin/ndCGI.exe/DocView/.

iii

Japan/Nippon Requirements Only

Voluntary Control Council for Interference (VCCI) Statement

Taiwan Requirements

Bureau of Standards, Metrology and Inspection (BSMI) Statement

iv

Canada Requirements Only

Canadian Department of Communications Radio Interference Regulations

This digital apparat us (Passp ort 5430) does not exceed the Class A limits for radio-noise
emissions from digital app ara t us as set out in the Radio Interference Regulations of the
Canadian Department of Communications.

Règlement sur le brouillage radioélectrique du ministère des Communications

Cet appareil numérique (Passport 5430) respecte les limites de bruits radioélectriques visant les
appareils numériques de classe A prescrites dans le Règlement sur le brouillage radioélectrique
du ministère des Communica ti ons du Canada.

Canada CS-03 Rules and Regulations

Notice: The Industry Canada label identifies certified equipment. This cert ification means that
the equipment m ee ts te lecommunication s net wor k protective, operational and safe ty
requirements as prescribed in the appropriate Terminal Equipment Technical Requirements
document(s). The Depart m ent does not guarantee the equipment will operate to the user’s
satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the
facilities of th e local telecommu n ications company. The equipment must also be installed usi ng
an acceptable method of connection. The customer should be aware that compliance with the
above conditions may not prevent the degradation of service in some situations.

Canada Requirements Only

Repairs to certified equipment should be coordinate d by a repr esentative designated by the
supplier. Any repairs or alterations made by the user to this eq uipment, or equipment
malfunctions, may give the telecommunications company cause to request the user to
disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power
utility, telephone lines and internal metallic water pipe system, if present, are connected
together. This precaution may be particularly important in rural areas.

Caution: Users should not attempt to make such connections themselves, but should contact the
appropriate electric inspection authority, or electrician, as appropriate.

v

Notice: For equipment using loopstart lines, please note that the Rin ge r Equ ivalence Number
(REN) assigned to each te rm inal device provides an indication of the m aximum number of
terminals allowed to be connected to a telephone interface. The termination on an interface may
consist of any combination of devices subject only to the requirement that the sum of the Ringer
Equivalence Numbers of all the devices does not exceed 5 . T he REN is located on the “F CC
Rules Part 68” label l ocated on the bracket of the module, or on the back of the unit.

Canada CS-03 -- Règles et règlements

Avis: L'étiquette d'Industrie Canada identifie le matériel homologué. Cette étiquette certifie que
le matériel est conform e aux normes de protection, d'expl oi tation et de sécurité des résea ux de
télécommunications, comme le prescrivent les docum e nts concernant les exigences tec hni ques
relatives au matériel terminal. Le Ministère n'assure toutefois pas que le matériel fonctionnera à
la satisfaction de l'utilisateur.

Avant d'installer ce matéri el, l'utilisateur doit s'assurer qu'il est permis de le raccorde r aux
installations de l'entreprise locale de télécommunication. Le matériel doit également être
installé en suivant une méthode acceptée de raccordement. L'abonné ne doit pas oublier qu'il est
possible que la conformité aux conditions énoncées ci -dessus n'empêche pas la dégradation du
service dans cert ai nes situations.

Les réparations de matér ie l ho mologué doivent être coordonnées pa r un représentant désigné
par le fournisseur. L'entreprise de téléco m m unications peut demander à l'ut ilisateur de
débrancher un apparei l à la suite de réparations ou de modification s effectuées par l'utilisateur
ou à cause de mauvais fonctionnement.

Pour sa propre protection, l'utilisateur doit s'assurer que tous les fils de mise à la terre de la
source d'énergie électrique, des lignes téléphoniques et des canalisations d'eau métalliques, s'il y
en a, sont raccordés ensemble. Cette précaution est particulièrement importante dans les régions
rurales.

Avertissement: L'utilisateur ne doit pas tenter de faire ces raccordements l u i-même; il doit
avoir recours à un service d'inspection des installations électriques, ou à un électricien, selon le
cas.

vi

Avis: Veuillez prendre note que pour tout appareillage supportant des lignes de type “loopstart,”
l'indice d'équivalence de la sonnerie (IES) a ssi gné à chaque dispositif terminal indique le
nombre maximal de terminaux qui peuvent être raccordés à une interface. La terminaison d'une
interface téléphoni que peut consister en une combi naison de quelques dispositifs, à la seule
condition que la somme d'indi ces d'équivalence de la sonnerie de tous les dispositifs n'excède
pas 5. Le REN figure sur l’étiquette “FCC Rules Part 68” située sur le support du module ou à
l’arrière de l’unité.

FCC Part 68 Compliance Statement

This equipmen t complies with Part 68 of F C C Rules. All direct connections to tel ephone
network lines must be made using standard plugs and jacks compliant with FCC Part 68. Please
note the following:

1. You are required to request service from the telephone company before you connect the
unit to a network. When you requ est servi ce, you must provide the telephon e c ompany
with the following data:

• When you request T1 Service, you must provide the telephon e company with

-- The Facility Interfac e Code
Provide the telephone company with all the codes below:

- 04DU9-BN (1.544 MB, D4 fram i ng format)

- 04DU9-DN (1.544 MB, D4 framin g format with B8ZF coding)

- 04DU9-1KN (1.544 MB, ESF frami ng format)

- 04DU9-1SN (1.544 MB, ESF fram i ng format with B8ZF coding)

- 04DU9-1ZN (1.544 MB, ANSI ESF and ZBTSI wi tho ut line power)

The telephone company will select the code it has available.

-- The Service Order Code(s) (SOC): 6.0 Y

-- The required Universal Service Order Code (USOC) j ac k: RJ 48C

vii

• When you request ISDN “U” Inte rface Service, you must provide the t el ep hone
company with

-- The Facility Interfac e Code: 02IS5

-- The Service Order Code(s) (SOC): 6.0 F

-- The required Universal Service Order Code (USOC) j ac k: RJ 49C

• When you request ISDN “S/T” Interface Service, you must provide the telephone
company with

-- The Service Order Code(s) (SOC): 6.0 P

-- The make, model number, and FCC Registration number of the NT1
Note: ISDN S/T cannot be directly connected to the network.

• When you request Primary Rate ISDN Service, you must provide the telephone
company with

-- The Facility Interface Code : 04DU9-1SN (1.544 MB, ESF framing format

with B8ZF coding)

-- The Service Order Code(s) (SOC): 6.0 Y

-- The required Universal Service Order Code (USOC) j ac k: RJ 48C

2. Your telephone company may ma ke cha nges to its facilities, equi pment, operations, or
procedures that cou ld affect the proper functioning of your equipment. The telephone
company will notify you in advance of such changes to give you an opportu n it y to
maintain uninterrupt ed telephone service.

3. If the unit causes harm to the telephone network, the telephone company may
temporarily discontinue your service. If possible, they will notify you in advance, but if
advance notice is not practic al , yo u will be notified as soon as possible and will be
informed of your right to file a c om plaint with the FCC.

viii

4. If you experience trouble with the unit, please contact the Nortel Networks Technical
Solutions Center in your ar ea for service or repairs. Repairs should be performed only
by service personnel authorize d by Norte l Ne tworks.

United States 1-800-2LANWAN
Valbonne, France 33-4-92-96-69-68
Sydney, Australia 61-2-9927-8800
Tokyo, Japan 81-3-5740-1700

5. You are required to notify the tel ephone company when you disc onnect the unit from
the network.

Nortel Networks NA Inc. Software License Agreement

NOTICE: Please carefully read this l icense agreemen t before copying or usin g the
accompanying software or installing the hardware unit with pre-enabled software (each of
which is referred to as “Software” in this Agreement). BY COPYING OR USING THE
SOFTWARE, YOU ACCEPT ALL OF THE TERMS AND CONDITIONS OF THIS
LICENSE AGREEMENT. THE TERMS EXPRESSED IN THIS AGREEMENT ARE THE
ONL Y TERMS UNDER WHICH NOR TEL NETWORKS WILL PERMIT Y OU TO USE THE
SOFTWARE. If you do not accept these terms and conditions, return the product, unused and in
the original shipping container, within 30 days of purchase to obtain a credit for the full
purchase price.

1. License Grant. Nortel Networks NA Inc. (“Nortel Networks”) grants the end user of the
Software (“Licensee”) a personal, nonexclusive, nontransferable license: a) to use the Software
either on a single computer or, if appl icable, on a s ingle authorized de v ice identified by host ID,
for which it was originally acquired; b) to copy the Software solely for backup purpo ses in
support of authorized use of the Software; and c) to use and copy the associated user m anual
solely in support of authori zed use of the Software by Licensee. Thi s lic e nse applies to the
Software only and does not extend to Nortel Networks Agent software or other Nortel Networks
software products. Nortel Networks Agent software or other Nortel Networks software products
are licensed for use under t he terms of the applicable Nort el N et wor ks NA Inc. Software
License Agreement tha t a cc om panies such software and upon payment by the end user of the

ix

applicable license fees for such software.

2. Restrictions on use; reservation of rights. The Software and user manu als are protected
under copyright laws. Nortel Networks and/or its licensors retain all title and ownership in both
the Software and user manuals, including any revisions made by Nortel Networks or its
licensors. The copyright not ic e must be reproduced and included with any copy of any portion
of the Software or user manuals. Li censee may not modify, translate, decompile, disa ssem b l e,
use for any competitive analysis, reverse engineer, distribute, or create derivative works from the
Software or user manuals or any copy, in whole or in part. Exce pt as expressly provided in this
Agreement, Lice nsee ma y not copy or tran sfer th e Soft ware or user manua ls, in wh ole o r in par t.
The Software and user manuals em body Nortel Networks’ and its licensors’ con fident ial a nd
proprietary intellectual property. Licensee shall not sublicense, assign, or otherwise disclose to
any third party the Software, or any inform a ti on about the operation, de sign, performance, or
implementati on o f th e Soft w are a nd u ser manu al s that is confidential to N ort el N etwo rks a nd i ts
licensors; however, Licensee may grant permission to its consultants, subcontractors, and agents
to use the Software at Licensee’s facility, provided they have agreed to use the Software only in
accordance with the ter ms of t his license.

3. Limited wa rranty. Nortel Networks warrants each item of Software, as delivered by Nortel
Networks and properly installed and operated on Nortel Networks hardware or other equipment
it is origina lly licensed fo r, to function substa ntially as desc r ibed in its accompanying us er
manual during its warranty perio d, wh ich begins on the date Software is first shipped to
Licensee. If any item of Software fail s to so function during its warranty peri od, as the sole
remedy Nortel Networks will at its discretion provide a suitable fix, patch, or workaround for
the problem that may be included in a future Software release. Nortel Networks further warrants
to Licensee that the me di a on which the Software is provided will be free from defects in
materials and workmanship unde r normal use for a period of 90 days from the dat e Software is
first shipped to Licensee. Nortel Netwo rks will replace defective media at no cha rge if it is
returned to Nortel Networks during the warranty period along with proof of the date of
shipment. This warranty do e s no t apply if the media has been dam aged as a result of accident,
misuse, or abuse. The Licensee assumes all responsibili ty for sel ection of the Software to
achieve Licensee’s intended results and for the instal la tion, use, and results obtained fro m the
Software. Nortel Networks does not warrant a) th at the functions contained in the software wil l
meet the Licens ee’s requirements, b) that the S oftware will operate in the hardware or softwa re

x

combinatio ns th a t the Licensee m ay s elect, c) that the operation of the S oft ware will be
uninterrupted or error free, or d) that all defects in the operation of the Software will be
corrected. Nortel Netwo rks is not obligated to remedy any Software defe ct that cannot be
reproduced with the late st Software release. These warrant ie s do not apply to the Software if it
has been (i) altered, except by Nortel Networks or in accordance with its instructions; (ii) used
in conjunction with another vendor’s product, resulting in the de fe ct; or (iii) damaged by
improper environment, abuse, misuse, accident, or negligence. THE FOREGOING
WARRANTIES AND LIMITATIONS ARE EXCLUSIVE REMEDIES AND ARE IN LIEU
OF ALL OTHER WARRANTIES EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A
PARTICULAR PURPOSE. Licensee is responsible for the security of its own data and
information and for maintaining adequate procedures apart from the Software to reconstruct lost
or altered files, data, or programs.

4. Limitation of liability. IN NO EVENT WILL NORTEL NETWORKS OR ITS
LICENSORS BE LIABLE FOR ANY COST OF SUBSTITUTE PROCUREMENT; SPECIAL,
INDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGES; OR ANY DAMA GES
RESULTING FROM INACCURATE OR LOST DATA OR LOSS OF USE OR PROFITS
ARISING OUT OF OR IN CONNECTION WITH THE PERFORMANCE OF THE
SOFTWARE, EVEN IF NORTEL NETW ORKS HAS BEEN AD VISED OF THE
POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL THE LIABILITY OF
NORTEL NETWORKS RELATING TO THE SOFTWARE OR THIS AGREEMENT
EXCEED THE PRICE PAID TO NORTEL NETWORKS FOR THE SOFTWARE LICENSE.

5. Gover n ment Licensees. This provision applies to all Software and documentation acquire d
directly or indirectly by or on behalf of the United States Government. The Soft wa re a nd
documentation are commercial products, licensed on the open market at market prices, and were
developed entirely at private expense and without the use of any U.S. Government funds. The
license to the U.S. Government is granted only with restricted rights, and use, duplication, or
disclosure by the U.S. Government is subject to the restrictions set fo rth in subparagraph (c)(1)
of the Commercial Co m put er Software––Restricted Ri ghts clause of FAR 52.227-19 and the
limitations set out in this license for civilian agencies, and subparagraph (c)(1)(ii) of the Rights
in Technical Data and Computer Software clause of DFARS 252.227-7013, for agencies of the
Department of Defense or their succe ssors, whi chever is applic able.

xi

6. Use of Software in the European Community. This provision applies to all Software
acquired for use within the European Community. If Licensee uses the Softwa re wi thin a
country in the Europea n Com munity, the Software Directive enacted by the Council of
European Commu nit ies Directive dated 14 May, 1991, will apply to the examination of the
Software to facilitate in teroperability. Licensee agrees to no ti fy Nortel Networks of any such
intended examination of t he Software and may procure support and assistance from Nortel
Networks.

7. Term and termination. This license is effective until terminated; however, all of the
restrictions with respec t to Nortel Networks’ copyright in the Soft wa re a nd user manuals will
cease being effective at the date of expirat ion of the Nortel Networks copy right; those
restrictions relating to use and disclosure of Nort el Networks’ confidential info rm ation shall
continue in effect. Licensee may ter m inate this license at any time. The lic ens e will
automatically terminate if Licensee fails to comply with any of the terms and conditions of the
license. Upon termination for any reason, Licensee will immediately destroy or return to Nortel
Networks the Software, user manuals, and all copies. Nortel Net wo rks is not liable to Licensee
for damages in any form solely by reason of the termination of this license.

8. Export and Re-export. Licensee agrees not to export, directly or in directly, the Software or
related technical data or information without first obtaining any required export licenses or other
governmental approvals. Without lim iting the foregoing, L ic ensee, on behalf of it s el f and its
subsidiaries and affiliates, agrees that it will not , without first obtaining all export licenses and
approvals required by the U.S. Government: (i) export, re-export, transf er, or divert any such
Software or technical data , or any direc t product thereof, to any country to which such exports
or re-exports are restricted or em bargoed under United States export co ntrol laws and
regulations, or to any national or resid ent of such restricted or embargoed co unt rie s ; or (ii)
provide the Software or related technical data or information to any military end user or for any
military end use, including the design, development, or production of any chemical, nuclear, or
biological weapons.

9. General. If any provision of this Agreement is held to be invalid or unenforceable by a court
of competent jurisdiction, the remainder of the provisions of this Agreement shall remain in full
force and effect. This Agreement will be governed by the laws of the state of California.

Should you have any questions concern in g this Agreement, contac t Nortel Networks, 4401
Great America Parkway, P.O. Box 58185, San ta Clara, California 95054-8185.

xii

LICENSEE ACKNOWLEDGES THAT LICENSEE HAS READ THIS AGREEMENT,
UNDERSTANDS IT, AND AGREES TO BE BOUND BY ITS TERMS AND CONDITIONS.
LICENSEE FURTHER AGREES THAT THIS AGREEM ENT IS THE ENTIRE AND
EXCLUSIVE AGREEMENT B ETWE EN NORTEL NETWORKS AND LICENSEE, WHICH
SUPERSEDES ALL PRIOR ORAL AND WRITTEN AGREEMENTS AND
COMMUNICATIONS BETWEEN THE PARTIES PERTAINING TO THE SUBJECT
MATTER OF THIS AGREEMENT. NO DIFFERENT OR ADDITIONAL TERMS WILL BE
ENFORCEABLE AGAINST NORTEL NETWORKS UNLESS NORTEL NETWORKS
GIVES ITS EXPRESS WRITTEN CONSENT, INCLUDING AN EXPRESS WAIVER OF
THE TERMS OF THIS AGREEMENT.

xiii

Contents

Preface 1

Before You Begin1
Text Conventions1
Acronyms2
Hard-Copy Technical Manuals2
How to Get Help3

About the Power Supply 4

Checking Status Indicators6
AC Input Electrical Requirements8

Adding or Replacing a Power Supply 9

Adding a Second Power Supply10
Replacing a Power Supply12
Removing and Installing a Power Supply Filler Panel14
Removing a Power Supply Filler Panel14
Installing a Power Supply Filler Panel16

Connecting to the Power Source 17

Connecting to the AC Power Source17

xv

Preface

In this guide, the Passport 5430 Multiservice Access Switch is referred to as
the Passport 5430.

Before You Begin

This guide is intended for qualified service personnel who need to add or
replace a Passport 5430 power supply. A qualified service person should
have appropriate technical training and experience and be aware of the
hazards involved in installing and replacing power supplies.

Before installing the Passport 5430, ensure that all network wiring had been
installed on the premises using standard cable-system practices.

Text Conventions

This guide uses the following text conventions:

italic text

Indicates new terms and book titles.

1

Acronyms

EIA Electronic Industries Association
LED light-emitting diode

Hard-Copy Technical Manuals

You can print selected technical manuals and release notes free, directly
from the Internet. Go to support.baynetworks.com/library/tpubs/. Find the
product for which you need documentation. Then locate the specific
category and model or ve rsio n for your hardw are or softw are product . Using
Adobe Acrobat Reader, you can open the manuals and release notes, search
for the sections you need, and pr in t them on mos t standard printers. You can
download Acrobat Reader free from the Adobe Systems Web site,
www.adobe.com.

You can purchase selected documentation sets, CDs, and technical
publications through the collateral catalog. The catalog is located on the
World Wide Web at support.baynetworks.com/catalog.html and is divided
into sections arranged alphabetically:

• The “CD ROMs” section lists available CDs.

• The “Guides/Books” section lists books on technical topics.

2

• The “Technical Manuals” section lists available printed documentation
sets.

How to Get Help

If you purchased a service contract for your Nortel Netwo rks pro duct from a
distributor or authorized reseller, contact the technical support staff for that
distributor or reseller for assistance.

If you purchased a Nortel Networks service program, contact one of the
following Nortel Networks Technical Solutions Centers:

Technical Solutions Center Telephone Number

Billerica, MA 800-2LANWAN (800-252-6926)
Santa Clara, CA 800-2LANWAN (800-252-6926)
Valbonne, France 33-4-92-96-69-68
Sydney, Australia 61-2-9927-8800
Tokyo, Japan 81-3-5740-1700

3

About the Power Supply

FBR0031A

DC OK

PS1

PS2

Power supplies

DC OK

Power switch

The Passport 5430 contains one or two AC-input power supplies. Figure 1
shows the location of the power supplies in the Passport 5430.

Figure 1. Location of the Power Supplies

in the Passport 5430

4

The Passport 5430 ships with a single AC power supply. You can install a
second power supply for redundancy and high-availability operation.

Figure 2 shows an AC input power supply.

DC OK

100-240V~ 50-60Hz 25A

FBR0050A

Figure 2. Passport 5430 Power Supply

The operating system generates an event message in response to any change
in the status of a power module. These messages identify the power supply
by its slot. From t he back of the P ass port 5430, power supply 1 is on the left,
and power supply slot 2 is on the right.

5

Checking Status Indicators

FBR0024A

Module 3

Module 4

Module 5

Remote
Console

5V FLASH ONLY

PCMCIA 2

Module 2 Module 1 Port 1

Insert
Extract

PCMCIA 1

SYNC
LOOP

RED
ALM

TX/RX

SPD
Link

PS1
PS2
Fan

WAN
Mod2
cPCI

Run
Boot
Sys

YEL
ALM

Console

System

Processor

Expansion Card

ATM

T1/E1

Dsync

Dsync

Insert
Extract

Expansion Card

Daul

T1/E1

Insert
Extract

Module 2 Module 1

Module 2 Module 1

Module 2 Module 1

Voice Processor

Dsync

Dsync

COM

U

D

DD

B1

B2

RLSD

Serial

ISDN BRI
withNT1

Telco

Tx

Rx

RLSD

DTR

V.34 Modem

COM

RLSD

Serial

Port 2

Module 1 Port 1

TX/RX

SPD
Link

PS1
PS2
Fan

WAN
Mod2
cPCI

Run
Boot
Sys

Console

System

processor

Port 2

PCI Slot 1

PCI Slot 2

PCI Slot 3

PCI Slot 4

Port 1
Port 2

Port 1
Port 2

Port 1
Port 2

Port 1
Port 2

Figure 3 shows the location of the power supply LEDs on the s ys tem
processor card.

Figure 3. Passport 5430 System Processor Card

6

Diagnostic LEDs

Table 1 describes the power supply LEDs.

Table 1. AC Power Module LEDs

LED State Meaning

PS1 Off Power off

On (green) Power supply is operating.
Rapid flashing

(green)

PS2 Off Power off

On (green) Redundant power supply (optional) is

Rapid flashing
(green)

Power supply failed.

operating.
Redundant power supply failed.

7

AC Input Electrical Requirements

The installation site must meet the following electrical requirements for AC
power (Table 2):

Table 2. Electrical Requirements

Input Voltage Range Maximum Input Current

90-264 volts alternating current (VAC) 1.0 amperes (A)

Table 3 lists the wall receptacle requirements for AC power.

Table 3. Wall Receptacle Requirements for AC Power

Country Receptacle Voltage

United States
and Canada

Any other
country

8

National Electrical Manufacturers Association
(NEMA) 5-15R standard receptacle

Your Passport 5430 distributor attaches the
necessary plug to the power cable and
informs you of the receptacle you need.

100-120 V

100-240 V

Adding or Replacing a Power Supply

This chapter describes how to add or replace a Passport 5430 power supply,
as follows:

Topic Page

Adding a Second Power Supply 10
Replacing a Power Supply 12
Removing and Installing a Power Supply Filler Panel 14

9

Adding a Second Power Supply

To add a second power supply:

1. Put on an antistatic wrist strap.

Caution:

Electrostatic discharge can damage hardware. You
must wear the antistatic wri st strap on your arm whenever you
handle printed circuit boards. Refer to the instructions
enclosed wtih your antistatic wrist strap to attach it.

2. Remove the power supply filler panel.

For instructions, see “Removing and Installing a Power Supply Filler
Panel” on page14.

3. Grasp the handle and push the power supply into the slot along the side

guides, and gently insert the supply (Figure 4).

10

DC OK

100-240V~ 50-60Hz 25A

PS1

100-240V~ 50-60Hz 25A

DC OK

PS2

Captive screw

Figure 4. Removing or Installing a Power Supply

Using a flat-tip screwdriver, tighten the captive screw until the power

4.

supply is seated firmly.

FBR0009A

11

When you insert an operational second power supply into the Passport
5430 with the power on, the PS2 LED on the system processor module
turns on. At the same time, the Passport 5430 automatically redistributes
the load between the two power supplies.

5. Connect to the AC power source.

For instructions, see “Connecting to the AC Power Source” on page 17.

6. Turn on the power supply power switch.

Replacing a Power Supply

To replace a power supply:

Caution:

To maintain proper cooling, neve r operate the Pass­port 5430 with an empty power supply slot. If you are replac­ing a failed se con d power supply and you do not have a power
filler panel, leave the failed power supply installed until a
replacement power supply is available.

1. Turn off the power switch on the power supply you are replacing.

12

Put on an antistatic wrist strap.

2.

Caution:

Electrostatic discharge can damage hardware. You
must wear the antistatic wri st strap on your arm whenever you
handle printed circuit boards. Refer to the instructions
enclosed with your antistatic wrist strap to attach it.

3. Disconnect the power cable from the power connector on the power

supply.

4. Using a flat-tip screwdriver, loosen the captive screw that fastens the

power supply to the chassis until the power supply disengages
(Figure 4).

5. Grasp the handle and u sing both hands, pull the p ower supply ou t of the

Passport 543 0.
You can remove an operational power supply without affecting the

operation of the Passport 5430. When you remove a power supply, the
associated LED (PS1 or PS2) on the system pro cessor mod ule turns o ff,
and the Passport 5430 automatically redistributes the load to the
remaining power supp ly.

6. Grasping the handle, guide the replacement power supply into the slot

along the side guides and gently insert the supply (see Figure 4 on
page 11).

13

Using a flat-tip screwdriver, tighten the captive screw until the power

7.

supply is seated firmly.

8. Connect to the AC power source.

For instructions, see “Connecting to the AC Power Source” on page 17.

9. Turn on the power supply power switch.

Removing and Installing a Power Supply Filler Panel

Nortel Networks ships the Passport 5430 with a filler panel in the power
supply slot reserved for the second power supply.

Before you can install a second power supply, you must remove the power
supply fille r pan el. fo r in stru ctions , see the ne xt secti on, “Rem ov ing a Power
Supply Filler Panel.”

If you remove a power supply from the Passport 5430 without replacing it,
you must install a power filler panel to maintain the proper cooling airflow.
For instructions, see “Installing a Power Supply Filler Panel” on page 16.

Removing a Power Supply Filler Panel

To remove a power supply filler panel:

1. Using a flat-tip screwdriver, loosen the captive screw that fastens the

power supply filler panel to the chassis until the filler panel disengages
(Figure 5).

14

DC OK

100-240V~ 50-60Hz 25A

PS1 PS2

Figure 5. Removing a Power Supply Filler Panel

FBR0059A

15

Pull the power supply filler panel away from the Passport 5430.

2.

Caution:

To maintain proper cooling, neve r operate the Pass­port 5430 with an empty power supply slot. Save the filler
panel to cov er the sl ot in cas e you nee d to opera te the P ass port
5430 with a

power supply removed.

Installing a Power Supply Filler Panel

If you remove a power supply from the Passport 5430 without replacing it,
you must install a power supply filler panel to maintain the prop e r cooling
airflow.

To install a power supply filler panel:

1. Place the power supply filler panel over the empty power supply slot.

2. Using a flat-tip screwdriver, tighten the captive screw until the power

supply filler panel firmly covers the slot.

16

Connecting to the Power Source

This chapter describes how to connect the Passport 5430 to the AC power
source.

Connecting to the AC Power Source

To connect the power cable to the Passport 5430:

1. Connect the a power cable to the power connector on each of the power

supplies (Figure 6).

17

Figure 6. Connecting the Po wer Cable to t he Passport 5430

FBR0031A

DC OK

PS1

PS2

Power supplies

DC OK

Power switch

Connect the remote end of the power cable to a grounded outlet.

2.

Turn the Passport 5430 on.

3.

18