Page 1
CE MAKER/MAQUINA DE HACER HIELO
INSTRUCTION MANUAL/MANUAL DE INSTRUCCIONES
Model Numbers / No. de Modelos: IMW24/IMP25
BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING
INSTRUCTIONS.
Avanti has a policy of continuous improvement on its products and reserves the right to change materials and specifications
without notice.
Avanti Products, A Division of The Mackle Co., Inc.
P.O. Box 520604 - Miami, Florida 33152
www.avantiproducts.com
Page 2
ICE MAKER SAFETY
YOUR SAFETY AND THE SAFETY OF OTHERS ARE VERY IMPORTANT.
We have provided many important safety messages in this manual for your appliance. Always read and
obey all safety messages.
This is the safety alert symbol. This symbol alerts you to
Potential hazards that can kill or injure you and others.
All safety messages will follow the safety alert symbol
And either the words” danger”, “warning” or “caution”.
Danger means that failure to heed this safety
statement may result in severe personal
injury or death.
Warning means that failure to heed this
safety statement may result in extensive
product damage, serious personal injury, or
death.
Caution means that failure to heed this
safety statement may result in minor or
moderate personal injury, property or
equipment damage.
All safety messages will alert you to know what potent ial hazard is, tell you how to reduce the chance of
injury, and let you know what can happen if the instructions are not followed.
2
Page 3
IMPORTANT SAFEGUIDES
Before the appliance is used, it must be properly positioned
and installed as described in this manual, so read the manual
carefully. To reduce the risk of fire, electrical shock or
injury when using the appliance , follow basic precaution,
Including the following:
? Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and do not use an
extension cord .
? It is recommended that a separate circuit, serving only your appliance be provided. Use receptacles that
cannot be turned off by a switch or pull chain.
? Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or explosion. And do
not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
The fumes can create a fire hazard or explosion.
? Before proceeding with cleaning and maintenance operations, make sure the power line of the unit is
disconnected.
? Do not connect or disconnect the electric plug when your hands are wet.
? Unplug the appliance or disconnect power before cleaning or servicing. Failure to do so can result in electrical
shock or death.
? Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in this
manual. All other servicing should be referred to a qualified technician.
FOLLOW WARNING CALL OUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL
? Use two or more people to move and install appliance. Failure to do so can result in back or other injury.
? To ensure proper v entilation for your appliance, the front of the unit must be completely unobstructed. Choose
a well-ventilated area with temperatures above 60°f (16°c) and below 90 °f (32°c). This unit must be installed in
an area protected from the element, such as wind, rain, water spray or drips.
? The appliance should not be located next to ovens, grills or other sources of high heat.
? The appliance must be installed with all electrical, water and drain connections in accordance with state and
local codes. A standard electrical supply (115 v ac only, 60 hz), properly grounded in accordance with the
national electrical code and local codes and ordinances is required.
? Do not kink or pinch the p ower supply cord of appliance .
? The fuse (or circuit breaker) size should be 15 amperes.
? It is important for the appliance to be leveled in order to work properly. You may need to make several
adjustments to level it.
? All installation must be in accordance with local plumbing code requirements.
? Make certain that the pipes are not pinched or kinked or damaged during installations .
? Check for leaks after connection.
? Never allow children to operate, play with or crawl inside the appliance.
? If you use the drainage container, you must set the drain select switch to off or the water can overflow from the
drainage container
? Although the unit has been tested at the factory, due to long-term transit and storage, the first batch of cubes
must be discarded.
? Do not use solvent- based cleaning agents of abrasives on the interior. These cleaners may damage or discolor
the interior.
? Do not use this apparatus for other than its intended purpose.
3
Page 4
REGISTRATION INFORMATION
Thank you for purchasing this fine Avanti product. Please fill out this form and return it within 100 days
of purchase to receive these important benefits to the following address:
Avanti Products, A Division of The Mackle Co., Inc.
P.O. Box 520604 - Miami, Florida 33152 USA
? PROTECT YOUR PRODUCT:
We will keep the model number and date of purchase of your new Avanti product on file to help
you refer to this information in the event of an insurance claim such as fire or theft.
? PROMOTE BETTER PRODUCTS:
We value your input. Your responses will help us develop products designed to best meet your
future needs.
-----------------------------------------------------(DETACH HERE) --------------------------------------------------------
AVANTI REGISTRATION FORM
__________________________________ _____________________________________
NAME MODEL # SERIAL #
_______________________________ ___ ______________________________ _______
ADDRESS DATE PURCHASED STORE/DEALER NAME
______________________________ ____ ___________________________________ ___
CITY STATE ZIP OCCUPATION
________________________________ __ AS YOUR PRIMARY RESIDENCE, DO YOU:
AREA CODE PHONE NUMBER ?OWN ?RENT
DID YOU PURCHASE AN ADDITIONAL WARRANTY: YOUR AGE:
?EXTENDED ?NONE ?UNDER 18 ?18-25 ?26-30
REASON FOR CHOOSING THIS AVANTI PRODUCT: ?31-35 ?36-50 ?OVER 50
PLEASE INDICATE THE MOST IMPORTANT FACTORS MARITAL STATUS:
THAT INFLUENCED YOUR DECISION TO PURCHASE ?MARRIED ?SINGLE
THIS PRODUCT. IS THIS PRODUCT USED IN THE:
?PRICE ?HOME ?BUSINESS
?PRODUCT FEATURES HOW DID YOU LEARN ABOUT THIS PRODUCT:
?AVANTI REPUTATION ?ADVERTISING
?PRODUCT QUALITY ?IN STORE DEMO ?PERSONAL DEMO
?SALESPERSON RECOMMENDATION ?OTHER______________________________
?FRIEND/RELATIVE RECOMMENDATION COMMENTS____________________________
?WARRANTY _____________________________________
?OTHER_______________________ _____________________________________
4
Page 5
5
Page 6
Help us help you…
Read this guide carefully.
It is in tended to help you operate and maintain
your new ice maker properly.
Keep it handy to answer your questions.
If you don't understand something or you need
more help, please call:
Avanti customer service
800-220-5570
Keep proof of original purchase date (such as
your sales slip) with this guide to establish the
warranty period.
If you need service
We're proud of our service and want you to be
pleased. If for some reason you are not happy
with the service you receive, here are some
steps to follow for further assistance.
First, contact the people who serviced your ice
maker. Explain why you are not pleased. In
most cases, this will solve the problem.
Next, if you are still not pleased, write all the
Write down the model and serial numbers.
You'll find them on a plate located on the rear
wall of the ice maker.
Please write these numbers here:
____________________ ________________
Date of purchase
____________________________________
Model number
____________________________________
Serial number
Use these numbers in any correspondence or
service calls concerning your ice maker.
If you received a damaged ice maker,
immediately contact the dealer (or builder) that
sold you the ice maker.
Save time and money. Before you call for
service, check the troubleshooting guide. It lists
causes of minor operating problems that you
can correct yourself.
details, including your telephone number, and
send it to:
Customer Service
Avanti Products
10880 NW 30th Street
Miami, Fl 33172 USA
6
Page 7
PARTS AND FEATURES
1. Inner Liner
2. Water Reservoir
3. Ice Collecting Tray
4. Ice Bin Full Sensor
5. Ice Shovel
6. Water Tray
7. Evaporator
8. Water Inlet Tube
9. Water Drain Plug
10. Compressor
11. Water Pump
12. Power Cord
13. Lid
14. Control Board
15. Window
7
Page 8
Table of contents
Ice Maker Safety 2
Important Safeguards 3
Registration Information 4
Help Us Help You … 6
Parts And Features 7
Important Safety Instructions 9
Installation Instructions 9
Before Using Your Ice Maker 9
Installation Of Your Ice Maker 9
Electrical Connection 10
Extension Cord 10
Control Panel Operation 10
Operating Instructions 11
Care And Maintenance 11
Cleaning Your Ice Maker 11
Space Requirements 12
Trouble Shooting Guide 12
Service For Your Ice Maker 12
Your Avanti Products Warranty 1 3
Wiring Diagram 1 4
INSTRUCCIONES EN ESPAÑOL _______________________ ________________________15-19
8
Page 9
IMPORTANT SAFETY INSTRUCTIONS
? WARNING?
? Read all instructions before using the ice maker.
? Danger or W arning: risk of child entrapment.
? Child entrapment and suffocation are not problems of the past. Junked or abandoned
appliances are still dangerous. . . Even if they will “just sit in the garage a few days.”
? Before you throw away your ice maker: take off the door. Leave the shelves in place so
that children may not easily climb inside.
? Never allow children to operate, play with, or crawl inside the appliance.
? Never clean ice maker parts with flammable fluids. The fumes can create a fire hazard or
explosion.
? Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of this
or any other ice maker. The fumes can create a fire hazard or explosion.
-save these instructions -
To reduce the risk of fire, electrical shock, or
injury when using your ice maker, follow these
basic precautions:
INSTALLATION INSTRUCTIONS
? Before Using Your Ice Maker
? Remove the exterior and interior packing.
? Check to be sure you have all of the following parts:
? 1 Ice Shovel
? 1 Instruction Manual
? Before connecting the ice maker to the power source, let it stand upright for approximately 2 hours.
This will reduce the possibility of a malfunction in the cooling system from handling during
transportation.
? Clean the interior surface with lukewarm water using a soft cloth.
? Installation Of Your Ice Maker
? Locate the ice maker away from direct sunlight and sources of heat (stove, heater, radiator, etc.).
Direct sunlight may affect the acrylic coating and heat sources may increase electrical
consumption. Extreme cold ambient temperatures may also cause the ice maker not to perform
properly.
? Plug the ice maker into an exclusive properly installed-grounded wall outlet. Do not under any
circumstances cut or remove the third (ground) prong from the power cord. Any questions
concerning power and or grounding should be directed toward a certified electrician or an
authorized Avanti products service center.
9
Page 10
? Electrical connection
?
WARNING
?
IMPORTANT:
YOU MUST
PRESS “STOP”. THEN THE “START” BUTTON TO RESTART THE
IMPROPER USE OF THE GROUNDED PLUG CAN RESULT IN THE RISK OF ELECTRICAL
SHOCK. IF THE POWER CORD IS DAMAGED, HAVE IT REPLACED BY AN AUTHORIZED
AVANTI PRODUCTS SERVICE CENTER.
? This ice maker should be properly grounded for your safety. The power cord of this ice maker is
equipped with a three-prong plug which mates with standard three prong wall outlets to minimize
the possibility of electrical shock.
? Do not under any circumstances cut or remove the third ground prong from the power cord
supplied.
? Never use an extension cord to connect power to the unit.
? Never use a two-prong grounding adapter.
? Where a two-prong wall receptacle is encountered, contact a qualified electrician to have it replaced
with a 3-prong receptacle in accordance with applicable electrical codes.
? This ice maker requires a standard 115/120 volts a.c.~/60hz electrical outlet with three -prong
ground.
? The cord should be secured behind the ice maker and not left exposed or dangling to prevent
accidental injury.
? Extension cord
Because of potential safety hazards under certain conditions, it is strongly recommended that you do
not use an extension cord with this appliance. However, if you must use an extension cord it is
absolutely necessary that it be a UL/CUL-listed, 3-wire grounding type appliance extension cord having
a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at least 10
amperes.
OPERATING YOUR ICE MAKER
? Control Panel Operation
Start
Press to turn unit on. This button is also used to start the ice making cycle.
Stop
Press to turn unit off.
Select
ICE SIZE SELECTION of (S) small, (M) medium or (L) large. (The chosen mode shall stay as
selected unless changed or there is a power failure).
Please select the (S) when ambient temperature is below 15°C (59ºF).
Alert
ADD WATER INDICATOR. The ”Alert ” light will come on with a beep sound. Add water and press
“STOP” button and then press “START” button to restart the icemaker.
Ice Full
ICE FULL INDICATOR. This light will come on with a beep sound which indicates that the storage
cabinet is full. Press the “STOP” button and remove the ice cubes then, press the “START” button
to restart the Ice maker.
ICE MAKER AFTER YOU ADD WATER OR REMOVE SOME OF THE ICE CUBES.
10
Page 11
Operating Instructions
Starting your Ice maker
? Open the lid and fill the reservoir with water. Make sure the water level in the reservoir is not
over the Ice collecting tray.
? Press START button to turn unit on.
? Select desired ice cube size by pressing “i ce size” selectors S, M and L.
? Check the water level in the reservoir periodically. The ice maker will detect any shortage of
water and stop operating. The ALERT indicator will be lit. Press the STOP button and fill the
reservoir with water. W ait 3 minutes after the ALERT light goes out and then press the START
button. The Ice maker will begin operation.
? When the ice cubes are collected and reaches the bin sensor, the ice maker will stop operating
and the ICE FULL indicator will be lit.
? There are three sizes of ice cubes available, therefore the larger the ice cube selected, the
longer the time it will take to complete the cycle. When the ambient temperature is lower than
15°C (59ºF), the small or medium ice cubes sizes are recommended to avoid ice cubes
clumping together.
? For best performance, water temperature should be between 7°C (45ºF) and 35°C (95ºF) and
ambient between 15°C (59 ºF) and 25°C (77ºF).
CARE AND MAINTENANCE
? Cleaning Your Ice Maker
? To ensure the cleanliness of the ice cubes, water in the reservoir should be replaced every 24
hours.
? If the compressor stops for any reason such as water shortage, too much Ic e, power off, etc... Do
not start the system right away, wait 3 minutes, and then re-start the Ice maker.
? Remove the drain plug to drain remaining water from the water reservoir when the ice maker will not
be used for long period of time. Screw the drain plug back in place after the water has been drained.
? Always change with fresh water before starting ice production at initial installation or after long
shut-off periods.
? Please clean your Ice maker regularly. When cleaning, unplug the unit and remove the ice cubes.
Use a diluted solution of water and vinegar to clean the inside and the outside surface of the Ice
maker. Do not spray Ice maker with chemicals or diluted agents such as acids, gasoline or oil.
Rinse thoroughly before starting.
Caution
Failure to unplug the ice maker could result in electrical shock or personal injury.
? Space Requirements
? During transportation, the incline angle of the cabinet should not be over 45°
? Do not turn the Ice maker upside down. Problems could occur in the compressor and sealed
system.
? The Ice maker should be placed horizontally on a properly leveled surface.
? To ensure proper ventilation for your Ice maker allow 6” of space at the top, the back and on each
side.
? Before using the Ice maker for the first time, please wait 2 hours after positioning it.
? Clean the inner liner, ice collecting tray, water box, ice shovel and evaporator frequently.
IMPORTANT: Do not install the Ice maker near an oven, radiator, or other heat source.
TEMPERATURE SENSOR
11
Page 12
? Power Failure
Most power failures are corrected within a few hours and should not affect the temperature of your ice
maker if you minimize the number of times the door is opened. If the power is going to be OFF for a
longer period of time, you need to take the proper steps to disconnect your appliance.
PROBLEMS WITH YOUR ICE MAKER?
You can solve many common ice maker problems easily, saving you the cost of a possible service call.
Try the suggestions below to see if you can solve the problem before calling the servicer.
TROUBLESHOOTING GUIDE
Problem Possible Cause Suggested Solutions
The compressor works
abnormally with a buzzing
Noise.
Water shortage ind icator
Light is on .
Ice full indicator light is on. Ice storage cabinet is full to the
Indicator lights are off. Blown fuse/ no power/blown
The ice made is too large
and with pieces sticking
together.
Conditions for ice making
cycle are right but no ice is
made.
Both alert and ice full
indicators are on.
The voltage is lower than
Recommended.
There is not enough water in the
reservoir.
top.
breaker
The water temperature in the
storage tray or ambient is too
low.
Refrigerant leaks/ sealed
system is blocked.
The water tray does not turn.
Stop the ice maker and do not restart
until the voltage is normal.
Press the stop button, fill with water,
wait 3 minutes and press the start
button to restart.
Remove some of the ice.
Replace fuse / turn power on .
Stop the machine and reset the ice
making cycle. Restart the machine
after turning it off.
Replace unit.
Check for blocked ice cubes .
Service For Your Ice Maker
We are proud of our customer service organization and the network of professional service technicians
that provide service on your Avanti ice maker. With the purchase of your Avanti ice maker, you can be
confident that if you ever need additional information or assistance, the Avanti Products Customer
Service team will be here for you. Just call us toll-free.
Avanti Products Customer Services
Product information
800-323-5029
Part orders
800-220-5570
In-home repair service
800-220-5570
Whatever your questions are about our products,
help is available.
You may order parts and accessories that will be
delivered directly to your home, by personal
check, money order, master card, or visa.
An Avanti Products authorized service center will
provide expert repair service, scheduled at a time
that is convenient for you. Our trained servicers
know your ice maker inside and out.
12
Page 13
YOUR AVANTI PRODUCTS
WARRANTY
What Is Covered
Limited One-Year
Warranty
For one year from the date of purchase by the
original owner, Avanti Products will, at its
option, repair or replace any part of the ice
maker which proves to be defective in material
or
Workmanship under normal use. During this
period Avanti Products will provide all parts and
labor necessary to correct such defects free of
charge, so long as the ice maker has been
installed and operated in accordance with the
written instructions in this manual. In rental or
commercial use, the warranty period is 90
days. All Avanti appliances of 3.5 cubic feet
capacity or less must be brought/sent to the
appliance service shop for repair.
Staple your sales receipt here. Proof of
original purchase date is needed to obtain
service under warranty.
Limited Second Through
Fifth Year Warranty
For the second through the fifth year from date of
original purchase, Avanti Products will provide a
replacement compressor free of charge due to a
failure. You are responsible for the service labor and
freight charges. In rental or commercial use, the
limited compressor warranty is one year and nine
months. Cost to move the ice maker to the servicers’
shop and back to the user's home, as may be
required, are the user's responsibility.
WHAT IS NOT COVERED
? Incidental or consequential damages.
? Parts and labor costs for the following will not
be considered as warranty:
? Door springs and/or frames.
? Inner door panels and/or door supports.
? Chest ice maker lid liners.
? Plastic cabinet liners.
? Repairs performed by unauthorized servicers.
? Service calls that do not involve defects in material or
workmanship such as customer education, door
reversal, or proper installation.
? Service calls that are related to external problems,
such as abuse, misuse, inadequate electrical power,
accidents, fire, floods, or acts of god.
? Replacement of house fuses or resetting circuit
breakers.
? Failure of the product if it is used for other than its
intended purpose.
? This warranty does not apply outside the continental
U.S.A.
13
Page 14
WIRING DIAGRAM
14
Page 15
INSTRUCCIONES EN ESPAÑOL
16. Cubierta interna
17. Depósito de agua
18. Bandeja de depósito de hielo
19. Censor para el compartimiento de hielo: Lleno
20. Pala para sacar el hielo
21. Bandeja para el agua
22. Evaporador
23. Manguera de abastecimiento de agua
24. Tapón para desagüe
25. Compresor
26. Bomba de agua
27. Cable eléctrico
28. Tapa
29. Tablero de control
30. Ventanilla
15
Page 16
IMPORTANTE: INSTRUCCIONES DE SEGURIDAD
? CUIDADO?
? Lea todas las instrucciones antes de usar su máquina de hacer hielo.
? Peligro o Cuidado : riesgo de que niños queden atrapados.
? Niños atrapados o muertos por asfixia no son una cosa del pasado. Aparatos
abandonados o considerados chatarra todavía son peligrosos… aun cuando “estén en el
garaje por unos días”.
? Antes de deshacerse de su máquina de hacer hielo : asegúrese de quitarle la tapa.
? Nunca deje que los niños operen, jueguen o gateen dentro del aparato .
? Nunca limpie las piezas de su máquina de hacer hielo con líquidos inflamables. Los gases
pueden causar un incendio o una explosión.
? No almacene, ni use gasolina o algún otro líquido o gas inflamable cerca de esta o alguna
otra máquina de hacer hielo. Los gases pueden causar un incendio o una explosión.
-Guarde estas instrucciones -
Para reducir el riesgo de fuego, descarga
eléctrica o daños personales mientras usa su
aparato, siga estas precauciones básicas:
INSTRUCCIONES DE INSTALACIÓN
? Antes de usar su máquina de hacer hielo
? Quite los empaques exteriores e interiores.
? Verifique y asegúrese de tener las piezas que se detallan a continuación:
? 1 Pala de hielo
? 1 Manual de instrucciones
? Antes de conectar su aparato a una fuente de electricidad, déjelo reposar de pie por dos horas
aproximadamente. Esto reducirá las posibilidades de fallas en el funcionamiento del sistema de
enfriamiento debido al movimiento durante el transporte.
? Limpie la superficie interior con agua tibia y un paño suave.
? Instalando su máquina de hacer hielo
? Ubique su aparato en un lugar donde los rayos del sol no caigan directamente y lejos de fuentes de
calor (estufas, calentadores, radiadores, etc.). Los rayos del sol podrían afectar el recubrimiento
acrílico y las fuentes de calor podrían incrementar el consumo eléctrico. Ambientes
extremadamente fríos podrían causar que su aparato no funcione apropiadamente.
? Conecte su máquina de hacer hielo a un enchufe de pared (con conexión a tierra) y que sea
exclusivo para este fin. Bajo ninguna circunstancia corte o quite el tercer punto (conexión a tierra)
del cable eléctrico. Si tiene alguna pregunta respecto de la fuente eléctrica y/o la conexión a tierra,
ésta deberá ser dirigida a un electricista certificado o a un centro de servicio autorizado de Avanti
Products.
16
Page 17
? Conexión Eléctrica
?
CUIDADO
?
IMPORTANTE:
ANTES DE A
ADIR AGUA O SACAR HIELO DEBER
PRESIONAR “STOP”.
EL USO INAPROPIADO DE LA CONEXIÓN A TIERRA INCREMENTARÁ EL RIESGO DE
DESCARGA ELÉCTRICA. SI EL CABLE DE ELECTRICIDAD ESTÁ DAÑADO, HÁGALO
REEMPLAZAR POR EN CENTRO DE SERVICIO DE AVANTI PRODUCTS????.
? La máquina de hacer hielo debe estar apropiadamente conectada a tierra por su seguridad. El
enchufe del cable eléctrico de su aparato está equipado con tres puntos, éstos están diseñados
para ser usados con los enchufes de pared estándar y reducir el riesgo de una descarga eléctrica.
? Bajo ninguna circunstancia corte o quite el tercer punto (conexión a tierra) del cable eléctrico.
? Nunca use un cable de extensión para conectar su aparato.
? Nunca use un adaptador de dos puntos.
? Si solo tiene enchufes de pared de dos puntos, contáctese con un electricista calificado para que lo
reemplace por uno de tres puntos y que cumpla con lo establecido en el código de electricidad.
? Esta máquina de hacer hielo requiere un enchufe eléctrico estándar (115 v AC, 60 hz) apropiado,
con conexión a tierra.
? El cable eléctrico deberá estar asegurado a la parte posterior de su aparato y no deberá quedar
expuesto o colgando, para prevenir heridas accidentales.
? Cable de extensión
Debido a que, bajo ciertas circunstancias, existen peligros potenciales contra su seguridad, se
recomienda no usar un cable de extensión con este aparato. Sin embargo, si por algún motivo tuviera la
necesidad de usar uno, éste tendrá que ser: un cable de extensión para aparatos eléctricos, de tres
cables, aprobado por UL/CUL, cuyo enchufe y salida tengan conexión a tierra, y que el cordón pueda
conducir 115 voltios y no menos de 10 amperios.
PONIENDO EN FUNCIONAMIENTO SU MÁQUINA DE HACER HIELO
? Uso del Panel de Control
Inicio (Start)
Presione este botón para encender. También se usa este botón para iniciar el ciclo de fabricación
de hielo.
Parar (Stop)
Presione para este bot ón para apagar.
Seleccionar (Select)
SELECCIÓN DEL TAMAÑO DEL HIELO. Elija entre pequeño (S), mediano (M), y grande (L).
(Este tamaño seleccionado permanecerá hasta que elija otro o por alguna falla en la fuente
eléctrica).
Por favor seleccione “S” cuando la temperatura del ambiente esté por debajo de los 15°C (59ºF).
Alerta (Alert)
INDICADOR DE FALTA DE AGUA. La luz de esta alerta se encenderá y sonará un “bip”. Añada agua
y presione “STOP”. Finalmente presione “START” para reiniciar la máquina.
Carga de Hielo completa (Ice Full)
INDICADOR DE CARGA DE HIELO COMPLETA. La luz de esta alarma se encenderá y sonará
un “bip” indicando que el depósito de hielo está completamente lleno. Presione “STOP” y saque
los cubos de hielo. Para reiniciar la máquina presione “START”.
DESPUÉS PRESIONE “START” PARA REINICIAR LA M ÁQUINA.
Ñ
Á
17
Page 18
Instrucciones de Uso
Comenzando a usar su máquina de hacer hielo
? Abra la tapa y llene el depósito con agua. Asegúrese que el nivel de agua no sea tal, que cubra
la bandeja de depósito de hielo.
? Presione “START” para encender su unidad.
? Seleccione el tamaño deseado de cubos de hielo con el selector “ice size” (S, M o L).
? La máquina de hielo comenzará a funcionar.
? Verifique el nivel del agua en el depósito periódicamente. La máquina detectará la falta de
agua y dejar á de funcionar. El indicador de alerta “ALERT” se encenderá. Presione “STOP” y
llene el depósito con agua. 3 minutos después que la luz de alerta “ALERT” se apague,
presione “START”. La máquina de hacer hielo comenzará a funcionar nuevamente.
? Cuando la cantidad de hielo pr oducida llegue al censor del depósito, la máquina dejará de
funcionar y el indicador carga de hielo completa “ICE FULL” se encenderá.
? Existen tres tamaños de cubos de hielo para escoger, y por tanto, el tiempo para completar el
ciclo dependerá del tamaño del cubo que elija (m ás grande, más tiempo). Cuando la
temperatura de la habitación esté por debajo de los 15°C (59ºF), se recomienda escoger los
cubos pequeños “S” o medianos “M” (esto evitará que los cubos se peguen unos con otros).
? Para un mejor funcionamiento, la temperatura del agua debe estar entre los 7°C (45ºF) y 35°C
(95ºF) y la de la habitación entre 15°C (59ºF) y 25°C (77ºF).
CUIDADO Y MANTENIMIENTO
? Limpiando su máquina de hacer hielo
? Para asegurar una mayor limpieza en los cubos de hielo, el agua del depósito deberá cambiarse
cada 24 horas.
? Si el compresor se detiene por motivos tales como falta de agua o mucho hielo, presionar el botón
de apagado, etc., NO reinicie la máquina inmediatamente, espere tres minutos y luego podrá
hacerlo.
? Deberá quitar el tapón de desagüe para sacar el agua restante del depósito cuando la máquina no
vaya a producir hielo por un tiempo considerable. Atornille de vuelta el tapón de desagüe luego de
haber sacado toda el agua.
? Siempre use agua fresca en su depósito, ya sea cuando produzca hielos por primera vez o luego
de un período considerable en que la máquina no estuvo en funcionamiento.
? Por favor limpie su máquina con regularidad. Para hacerlo, desconéctela y saque todos los cubos
de hielo. Use una solución de agua y vinagre (disuelto en ésta) para limpiar el interior y las
superficies exteriores de su aparato. No utilice agentes químicos o diluyentes (tales como ácido,
gasolina o aceite). Enjuague a fondo antes de poner en funcionamiento su máquina.
Precaución
Si no desconecta la máquina podría recibir una descarga eléctrica o daños personales.
? Necesidades de espacio
? Mientras es transportado, el ángulo de inclinación del aparato no deberá ser mayor a 45°.
? No ponga la máquina de hacer hielo de cabeza. Esto podría causar problemas con el compresor y
el sistema de sellado.
? La máquina de hacer hielo deberá ser ubicada en posición horizontal en una superficie nivelada.
? Para asegurarle una ventilación apropiada a su máquina, deje un espacio libre de 6” arriba, detrás
y a cada lado de la misma.
? Antes de usar su aparato por primera vez, espere dos horas luego de haberlo instalado.
? Limpie frecuentemente estas piezas de su máquina: la cubierta interna, la bandeja recolectora de
hielo, el depósito de agua, la pala del hielo y el evaporador.
IMPORTANTE: No instale la máquina de hacer hielo cerca de un
horno, radiador o alguna otra fuente de calor.
18
Page 19
? Fallas en la fuente eléctrica
La mayoría de fallas en la fuente eléctrica se corrigen en pocas horas y no afectarán la temperatura de
su unidad, si minimiza el número de veces que abre su puerta. Si la falla no se corrige por un largo
período, usted necesitará tomar las medidas apropiadas para desconectar su máquina.
¿PROBLEMAS CON SU MÁQUINA DE HACER HIELO?
Usted puede resolver fácilmente problemas comunes de su máquina, ahorrándose el posible costo de
una llamada de servicio. Inténtelo con estas sugerencias antes de llamar al servicio de mantenimiento.
GUÍA DE SOLUCIÓN DE PROBLEMAS
Problema Causa Probable Solución sugerida
El compresor funciona mal y
se escucha un zumbido.
La luz indicadora de falta de
agua está encendida.
El indicador de “carga de
hielo completa” está
encendido.
Las luces indicadoras están
apagadas.
Los cubos de hielo son muy
grandes y algunos se están
pegando.
Las condiciones para la
producción de hielo son
correctas, pero no se produce
hielo.
Las alertas de falta de agua y
carga de hielo llena, están
encendidas.
El voltaje es más bajo que el
recomendado.
No hay suficiente agua en el
depósito.
El depósito de hielo está
completamente lleno.
Voló el fusible/no hay
electricidad
La temperatura del agua en
la bandeja o la de la
habitación es muy baja.
Existe fuga del refrigerante/el
sistema de sellado está
bloqueado.
El depósito de agua está
trabado.
Apague la máquina hasta que el
voltaje vuelva a la normalidad.
Presione “STOP”, llene el depósito
con agua, espere 3 minutos y
presione “START” para reiniciar el
ciclo.
Saque un poco de hielo.
Cambie el fusible/Encienda su
máquina.
Apague la máquina y reajuste el ciclo
de producción de hielo. Reinicie la
máquina.
Cambiar la unidad.
Verifique que no existan cubos de
hielo que lo bloqueen.
Servicio de mantenimiento para su producto
Estamos orgullosos de la organización de nuestro servicio al cliente y de los técnicos profesionales que
proveen servicio a su máquina de hacer hielos Avanti. Cuando compra un producto Avanti, usted
puede estar seguro que si alguna vez necesita información o asistencia, el equipo de servicio al cliente
de Avanti Products estará para ayudarlo. Llámenos de manera gratuita.
Servicio al cliente de Avanti Products
Información de producto
800-323-5029
Pedido de piezas
800-220-5570
Servicio de reparación a domicilio
800-220-5570
Cualquier sea su pregunta sobre nuestros productos, la
ayuda está disponible.
Usted puede ordenar piezas y accesorios que serán
enviados directamente a su casa con cargo a un cheque
personal, órdenes de dinero, mastercard o visa.
Un centro de servicio autorizado de Avanti Products le
proveerá de un servicio de reparación experimentado,
éste será programado a la hora que le sea más
conveniente. Nuestro equipo de servicio está totalmente
entrenado y conoce su unidad por dentro y fuera.
P RINTED IN CHINA
19
Loading...